In commit b24bb99d cp110 configuration initially done in u-boot
was removed and delegated to atf firmware as smc call.
That commit didn't account for later introduced in d13b740c SATA invert polarity support.
This patch adds support of passing SATA invert polarity flags to atf
firmware during the smc call.
Signed-off-by: Denis Odintsov <shiva@mail.ru> Cc: Baruch Siach <baruch@tkos.co.il> Cc: Rabeeh Khoury <rabeeh@solid-run.com> Cc: Stefan Roese <sr@denx.de> Reviewed-by: Stefan Roese <sr@denx.de>
dm: pci: Fix handling of errors when scanning device
Some PCIe controller's read_config() method support indicating error
directly via return value, but some cannot distinguish all-ones (or
all-zeros) read response from an error.
The current code in pci_bind_bus_devices() interprets all-ones /
all-zeros in PCI_VENDOR_ID register as "nothing connected", and
continues the cycle, but an error returned via return value breaks the
cycle.
This is wrong for the PCIe controllers which return this error via
return value.
Handle all errors when reading PCI_VENDOR_ID the same way.
This fixes enumeration of PCI devices for example when there is a PCI
bridge connected behind another PCI bridge and not all ports are
connected to a device, and the controller (for example Aardvark)
translates the UR error (Unsupported Request) as -EOPNOTSUPP.
Signed-off-by: Pali Rohár <pali@kernel.org> Signed-off-by: Marek Behún <marek.behun@nic.cz> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Stefan Roese <sr@denx.de>
Simon Glass [Sat, 7 Aug 2021 13:24:12 +0000 (07:24 -0600)]
dm: gpio: Add of-platdata support
Add support for accessing GPIOs using of-plata. This uses the same
mechanism as for clocks, but allows use of the xlate() method so that
the driver can interpret the parameters.
Update the condition for GPIO_HOG so that it is not built into SPL,
since it needs SPL_OF_REAL which is not enabled in sandbox_spl.
Simon Glass [Sat, 7 Aug 2021 13:24:09 +0000 (07:24 -0600)]
clk: Rename clk_get_by_driver_info()
This is actually a misnomer now, since the phandle info may contain
a driver_info index or a udevice index. Rename it to use the word
'phandle', which seems more accurate. Add a comment while we are here.
Simon Glass [Sat, 7 Aug 2021 13:24:02 +0000 (07:24 -0600)]
fdt: Create a new OF_REAL Kconfig
The condition to indicate whether there is a runtime devicetree available
is OF_CONTROL && !OF_PLATDATA. This is a bit unweidly and is repeated in
a lot of places.
Add a new OF_REAL Kconfig which provides this information directly.
Note: This is similar in effect to LIBFDT. We might consider dropping
LIBFDT and using this instead, but this is left for now as we also have
OF_LIBFDT_OVERLAY which it would not make sense to change.
TCG EFI Protocol Specification defines the number_of_algorithms
field in spec ID event to be equal to the number of active
algorithms supported by the TPM device. In current implementation,
this field is populated with the count of all algorithms supported
by the TPM which leads to incorrect spec ID event creation.
Similarly, the algorithm array in spec ID event should be a variable
length array with length being equal to the number_of_algorithms field.
In current implementation this is defined as a fixed length array
which has been fixed.
Signed-off-by: Ruchika Gupta <ruchika.gupta@linaro.org> CC: Masahisa Kojima <masahisa.kojima@linaro.org> CC: Ilias Apalodimas <ilias.apalodimas@linaro.org> CC: Heinrich Schuchardt <xypron.glpk@gmx.de> Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Simon Glass [Sun, 19 Sep 2021 21:51:10 +0000 (15:51 -0600)]
doc: Add mention of the /config binding
The devicetree binding files are in their own directory and use a simple
text format. Add a link for the binding for the /config node, since it
is otherwise hard to find.
Suggested-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Kristian Amlie [Tue, 7 Sep 2021 06:37:51 +0000 (08:37 +0200)]
ARM: vexpress_ca9x4: Reintroduce board in order to use with QEMU.
vexpress_ca9x4 is seemingly the only board except for qemu_arm which
is able to run U-Boot correctly, using the `-M vexpress-a9` option to
QEMU. Building for qemu_arm and running qemu-system-arm with the `-M
virt` argument has a number of downsides, most importantly that it
only supports virtio storage drivers. This significantly reduces its
usefulness in testing memory card and Flash solutions, especially when
the tested images are from a third party source.
So therefore we reintroduce the vexpress_ca9x4 board in this commit,
with the explicit goal of using it with QEMU.
A number of differences to note from the original:
* Since the board was apparently unmaintained, I have now set myself
as the maintainer.
* The board has been converted to use the driver model, which was the
reason it was removed in the first place.
* The vexpress_ca15_tc2 and vexpress_ca5x2 boards, which were removed
in the same commit, are not necessary for the QEMU use case, and
have been omitted.
* An `mmc0` alias was introduced in the dts file. The mmc is not
detected correctly without this, now that it's based on the device
tree instead of the board's init function.
* A couple of other nodes were removed because they were problematic
when trying to run the UEFI bootmgr. Once again, the primary use
case here is QEMU, and these nodes are not needed for that to work.
* Unnecessary board init code has been removed, thanks to driver model
and device tree.
* `CONFIG_OF_EMBED` has been enabled. I know this goes against
recommended practice, but there doesn't seem to be any other way to
pass the dtb to U-Boot in the QEMU scenario. Using the -dtb argument
does not work, I suppose because U-Boot doesn't use the same
mechanics as the kernel when it's booting.
* Load addresses have been changed to fit QEMU use case.
People wanting to get a more detailed, yet somewhat isolated, diff
between this and the original, can run this command:
Patrick Delaunay [Wed, 22 Sep 2021 09:02:26 +0000 (11:02 +0200)]
mtd: remove SPEAr flash driver st_smi
Remove the driver st_smic.c used in SPEAr products and the associated
config CONFIG_ST_SMI; this driver is no more used in U-Boot after the
commit 570c3dcfc153 ("arm: Remove spear600 boards and the rest of SPEAr
support").
Fixes: 570c3dcfc153 ("arm: Remove spear600 boards and the rest of SPEAr support") Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com> Reviewed-by: Stefan Roese <sr@denx.de> Reviewed-by: Tom Rini <trini@konsulko.com>
Patrick Delaunay [Tue, 21 Sep 2021 16:18:51 +0000 (18:18 +0200)]
MAINTAINERS: remove SPEAR entry
As the lastest spear directories are removed, delete the associated entry
in the MAINTAINERS file:
- arch/arm/cpu/arm926ejs/spear/
- arch/arm/include/asm/arch-spear/
Fixes: 570c3dcfc153 ("arm: Remove spear600 boards and the rest of SPEAr support") Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
=> bootefi hello
Scanning disk mmc2.blk...
No valid Btrfs found
Bad magic number for SquashFS image.
** Unrecognized filesystem type **
Scanning disk mmc1.blk...
No valid Btrfs found
Bad magic number for SquashFS image.
** Unrecognized filesystem type **
Scanning disk mmc0.blk...
No valid Btrfs found
Bad magic number for SquashFS image.
** Unrecognized filesystem type **
Albeit a whole disk may be formatted with a filesystem in most cases
a partition table is used and the whole disk (partition number 0) doesn't
contain a filesytem. Some partitions may only contain a blob. Not seeing a
filesytem on the whole disk or on any partition is only worth a debug
message.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Our mailmapper script required Python 2 which is no longer maintained.
A main difference when converting to Python 3 is that byte strings are not
character strings. So add conversion and skip over conversion errors.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
test/py: tpm2: Skip tpm pytest based on env variable
Tpm test cases relies on tpm device setup. Provide an environment
variable "env__tpm_device_test_skip = True" to skip the test case
if tpm device is not present.
Only needed will have to add variable to the py-test framework.
Test runs successfully even this variable is absent.
Signed-off-by: Stefan Roese <sr@denx.de>
[trini: Make this default to off as it causes problems on some platforms still] Signed-off-by: Tom Rini <trini@konsulko.com>
Stefan Roese [Thu, 2 Sep 2021 15:00:18 +0000 (17:00 +0200)]
arm64: memset-arm64: Use simple memset when cache is disabled
The optimized memset uses the dc opcode, which causes problems when the
cache is disabled. This patch adds a check if the cache is disabled and
uses a very simple memset implementation in this case. Otherwise the
optimized version is used.
Ported from https://github.com/ARM-software/optimized-routines
These files are included from this repository, including the latest
git commit ID:
string/aarch64/memcpy.S: afd6244a1f8d
string/aarch64/memset.S: e823e3abf5f8
string/asmdefs.h: e823e3abf5f8
Note that memmove is also handled by the memcpy function.
Please note that when adding these optimized functions as default memset
memcpy functions in U-Boot, U-Boot fails to boot on the LX2160ARDB.
After the initial ATF output, no U-Boot output is shown on the serial
console. Some exception is triggered here in the very early boot process
as some of the assembler opcodes need the caches to be enabled.
Because of this, a follow-up patch will add a check to use a simple
non-optimized memset for the "cache disabled" case.
Note:
I also integrated and tested with the Linux versions of these optimized
functions. They are similar to the ones now integrated but these ARM
versions are still a small bit faster.
Tom Rini [Fri, 24 Sep 2021 02:38:21 +0000 (22:38 -0400)]
Merge branch '2021-09-23-assorted-updates' into next
- Rework lmb reservation so we have common code for all arches to use
- armv8 cache.S cleanups, crc32 speedup
- ENV_IS_NOWHWERE, pci io/memory base configuration fixes
pci: Fix configuring io/memory base and limit registers of PCI bridges
Lower 4 bits of PCI_MEMORY_BASE and PCI_MEMORY_LIMIT registers are reserved
and should be zero. So do not set them to non-zero value.
Lower 4 bits of PCI_PREF_MEMORY_BASE and PCI_PREF_MEMORY_LIMIT registers
contain information if 64-bit memory addressing is supported. So preserve
this information when overwriting these registers.
Lower 4 bits of PCI_IO_BASE and PCI_IO_LIMIT register contain information
if 32-bit io addressing is supported. So preserve this information and do
not try to configure 32-bit io addressing (via PCI_IO_BASE_UPPER16 and
PCI_IO_LIMIT_UPPER16 registers) when it is unsupported.
Signed-off-by: Pali Rohár <pali@kernel.org> Reviewed-by: Stefan Roese <sr@denx.de>
arm: mediatek: merge board Kconfigs into mach-mediatek
On MediaTek boards we cannot override the SYS_BOARD / SYS_CONFIG_NAME
variables from defconfig.
This is because in board/mediatek/mtXXXX/Kconfig this value was override
by default due to the if CONFIG_TARGET_MTXXXX condition.
Merge all the Kconfigs to the mach-medatek/Kconfig.
This way:
- we only define SYS_{SOC,VENDOR} once
- all board definitions are in a single place, simplifying the build logic.
Signed-off-by: Guillaume La Roque <glaroque@baylibre.com>
Marek Vasut [Fri, 10 Sep 2021 20:47:18 +0000 (22:47 +0200)]
lmb: x86: Add arch_lmb_reserve()
Add arch_lmb_reserve() implemented using arch_lmb_reserve_generic().
It is rather likely this architecture also needs to cover U-Boot with
LMB before booting Linux.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Simon Glass <sjg@chromium.org> Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com> Cc: Tom Rini <trini@konsulko.com>
Marek Vasut [Fri, 10 Sep 2021 20:47:17 +0000 (22:47 +0200)]
lmb: xtensa: Add arch_lmb_reserve()
Add arch_lmb_reserve() implemented using arch_lmb_reserve_generic().
It is rather likely this architecture also needs to cover U-Boot with
LMB before booting Linux.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Chris Zankel <chris@zankel.net> Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com> Cc: Tom Rini <trini@konsulko.com>
Marek Vasut [Fri, 10 Sep 2021 20:47:15 +0000 (22:47 +0200)]
lmb: riscv: Add arch_lmb_reserve()
Add arch_lmb_reserve() implemented using arch_lmb_reserve_generic().
It is rather likely this architecture also needs to cover U-Boot with
LMB before booting Linux.
Reviewed-by: Rick Chen <rick@andestech.com> Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Atish Patra <atish.patra@wdc.com> Cc: Leo <ycliang@andestech.com> Cc: Rick Chen <rick@andestech.com> Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com> Cc: Tom Rini <trini@konsulko.com>
Marek Vasut [Fri, 10 Sep 2021 20:47:14 +0000 (22:47 +0200)]
lmb: nds32: Add arch_lmb_reserve()
Add arch_lmb_reserve() implemented using arch_lmb_reserve_generic().
It is rather likely this architecture also needs to cover U-Boot with
LMB before booting Linux.
Reviewed-by: Rick Chen <rick@andestech.com> Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Rick Chen <rick@andestech.com> Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com> Cc: Tom Rini <trini@konsulko.com>
Marek Vasut [Fri, 10 Sep 2021 20:47:13 +0000 (22:47 +0200)]
lmb: nios2: Add arch_lmb_reserve()
Add arch_lmb_reserve() implemented using arch_lmb_reserve_generic().
It is rather likely this architecture also needs to cover U-Boot with
LMB before booting Linux.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com> Cc: Thomas Chou <thomas@wytron.com.tw> Cc: Tom Rini <trini@konsulko.com>
Marek Vasut [Fri, 10 Sep 2021 20:47:12 +0000 (22:47 +0200)]
lmb: Remove imx board_lmb_reserve()
This function is clearly architecture specific code, not board specific
code. The only difference from the previous arm arch_lmb_reserve() is the
extra reservation of 16k of memory below the stack bottom, rather than
the 4k. The common code now also uses 16k alignment. Remove this custom
implementation, as it now behaves exactly as the common code.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Alexey Brodkin <alexey.brodkin@synopsys.com> Cc: Angelo Dureghello <angelo@sysam.it> Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com> Cc: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com> Cc: Hai Pham <hai.pham.ud@renesas.com> Cc: Michal Simek <monstr@monstr.eu> Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com> Cc: Tom Rini <trini@konsulko.com> Cc: Wolfgang Denk <wd@denx.de> Cc: Ye Li <ye.li@nxp.com>
Marek Vasut [Fri, 10 Sep 2021 20:47:11 +0000 (22:47 +0200)]
lmb: arm: Increase LMB alignment to 16k in arch_lmb_reserve_generic()
According to input NXP, the 4k alignment is not always sufficient.
Currently iMX works around this problem by implementing board specific
LMB reservation, however it is likely this could also occur on other
systems. Increase the LMB reservation alignment to 16k by default.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Alexey Brodkin <alexey.brodkin@synopsys.com> Cc: Angelo Dureghello <angelo@sysam.it> Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com> Cc: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com> Cc: Hai Pham <hai.pham.ud@renesas.com> Cc: Michal Simek <monstr@monstr.eu> Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com> Cc: Tom Rini <trini@konsulko.com> Cc: Wolfgang Denk <wd@denx.de> Cc: Ye Li <ye.li@nxp.com> Reviewed-by: Tom Rini <trini@konsulko.com>
Marek Vasut [Fri, 10 Sep 2021 20:47:10 +0000 (22:47 +0200)]
lmb: Switch to generic arch_lmb_reserve_generic()
Switch arc/arm/m68k/microblaze/mips/ppc arch_lmb_reserve() to
arch_lmb_reserve_generic().
Reviewed-by: Tom Rini <trini@konsulko.com> Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Alexey Brodkin <alexey.brodkin@synopsys.com> Cc: Angelo Dureghello <angelo@sysam.it> Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com> Cc: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com> Cc: Hai Pham <hai.pham.ud@renesas.com> Cc: Michal Simek <monstr@monstr.eu> Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com> Cc: Tom Rini <trini@konsulko.com> Cc: Wolfgang Denk <wd@denx.de>
Marek Vasut [Fri, 10 Sep 2021 20:47:09 +0000 (22:47 +0200)]
lmb: Add generic arch_lmb_reserve_generic()
The arc/arm/m68k/microblaze/mips/ppc arch_lmb_reserve() implementations
are all mostly the same, except for a couple of details. Implement a
generic arch_lmb_reserve_generic() function which can be parametrized
enough to cater for those differences between architectures. This can
also be parametrized enough so it can handle cases where U-Boot is not
relocated to the end of DRAM e.g. because there is some other reserved
memory past U-Boot (e.g. unmovable firmware for coprocessor), it is not
relocated at all, and other such use cases.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Alexey Brodkin <alexey.brodkin@synopsys.com> Cc: Angelo Dureghello <angelo@sysam.it> Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com> Cc: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com> Cc: Hai Pham <hai.pham.ud@renesas.com> Cc: Michal Simek <monstr@monstr.eu> Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com> Cc: Tom Rini <trini@konsulko.com> Cc: Wolfgang Denk <wd@denx.de> Reviewed-by: Tom Rini <trini@konsulko.com>
Marek Vasut [Fri, 10 Sep 2021 20:47:08 +0000 (22:47 +0200)]
lmb: Always compile arch_lmb_reserve() into U-Boot on arc
The arch_lmb_reserve() is called by lib/lmb.c lmb_reserve_common() even
if CMD_BOOTM is not enabled. However, the arc variant of arch_lmb_reserve()
is only compiled in if CMD_BOOTM is enabled.
This currently does not trigger build error, because there is an empty
weak implementation of arch_lmb_reserve(), however that is not the
function that should be used on arc.
Fix this by moving the arch_lmb_reserve() implementation into common
code and always compile it in.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Simon Glass <sjg@chromium.org> Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com> Cc: Tom Rini <trini@konsulko.com>
Marek Vasut [Fri, 10 Sep 2021 20:47:07 +0000 (22:47 +0200)]
lmb: Always compile arch_lmb_reserve() into U-Boot on arm
The arch_lmb_reserve() is called by lib/lmb.c lmb_reserve_common() even
if CMD_BOOT{I,M,Z} is not enabled. However, the arm32/arm64 variant of
arch_lmb_reserve() is only compiled in if CMD_BOOT{I,M,Z} is enabled.
This currently does not trigger build error, because there is an empty
weak implementation of arch_lmb_reserve(), however that is not the
function that should be used on arm32/arm64.
Fix this by moving the arch_lmb_reserve() implementation into common
code and always compile it in.
Reviewed-by: Tom Rini <trini@konsulko.com> Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Simon Glass <sjg@chromium.org> Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com> Cc: Tom Rini <trini@konsulko.com>
Marek Vasut [Mon, 30 Aug 2021 13:05:23 +0000 (15:05 +0200)]
crc32: Add crc32 implementation using __builtin_aarch64_crc32b
ARMv8.0 has optional crc32 instruction for crc32 calculation. The
instruction is mandatory since ARMv8.1. The crc32 calculation is
faster using the dedicated instruction, e.g. 1.4 GHz iMX8MN gives:
Add implementation using the compiler builtin wrapper for the crc32
instruction and enable it by default, since we don't support any
platforms which do not implement this instruction.
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Simon Glass <sjg@chromium.org>
[trini: Make crc32_table guarded by CONFIG_ARM64_CRC32] Signed-off-by: Tom Rini <trini@konsulko.com>
Replace the current 2-instruction 2-step tripling code by a
corresponding single instruction leveraging ARMv8-A's "flexible second
operand as a register with optional shift". This has the added benefit
(albeit arguably negligible) of reducing the final code size.
Fix the comment as the tripled cache level is placed in x12, not x0.
Improve the file's readability and conciseness by using the appropriate
Aarch64 instruction: ubfx (unsigned bitfield extract). This makes the
code easier to follow as it directly manipulates the offsets and widths
of the fields read from system registers, as they are expressed in the
Standard (ARM ARM). This has the added benefit (albeit arguably
negligible) of reducing the final code size.
env: Make _init() expect _INVALID when _IS_NOWHERE
Avoid applying the "fix" introduced by commit 5557eec01cbf ("env: Fix
invalid env handling in env_init()") to the environment "nowhere".
This is necessary as that commit, by setting the return value of
env_init() to -ENOENT if gd->env_valid is ENV_INVALID, forces that
function to reset gd->env_valid to ENV_VALID. By doing so, it breaks the
assumption (required by ENV_IS_NOWHERE) that gd->env_valid must be
ENV_INVALID.
This, in turn, results in env_relocate() calling env_load() (it should
not), which itself, calls U_BOOT_ENV_LOCATION(nowhere).load() i.e.
env_nowhere_load(). That function, being implemented under the
assumption mentioned above, calls env_set_default(), which in turn,
seeing that gd->env_valid is ENV_VALID (it should not), tries to
dereference whatever lies in gd->env_addr (most likely garbage), leading
to a faulty memory access.
Note that other env_locations might be concerned by this bug but that
this commit only intends to fix it for when ENV_IS_NOWHERE.
Tom Rini [Wed, 22 Sep 2021 18:55:16 +0000 (14:55 -0400)]
Merge tag 'u-boot-at91-2022.01-a' of https://source.denx.de/u-boot/custodians/u-boot-at91 into next
First set of u-boot-at91 features for the 2022.01 cycle:
This feature set includes : the support for CPU driver for arm926
(sam9x60 device); changes required for OP-TEE boot for sama5d2_xplained
and sama5d27_som1_ek boards; QSPI boot configuration for sama5d2_icp;
starting to remove old Kconfig unused symbols from config_whitelist.txt
(work will take more time); also small fixes and updates in mach, DT,
configs, etc.
Marek Vasut [Tue, 14 Sep 2021 03:20:19 +0000 (05:20 +0200)]
ddr: altera: use KBUILD_BASENAME instead of __FILE__
The KBUILD_BASENAME contains just the name of the compiled module,
in this case 'sequencer', rather than a full path to the compiled
file. Use it to prevent pulling the full path into the U-Boot binary,
which is useless and annoying.
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Siew Chin Lim <elly.siew.chin.lim@intel.com> Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com> Cc: Tien Fong Chee <tien.fong.chee@intel.com>
Marek Vasut [Tue, 14 Sep 2021 03:25:32 +0000 (05:25 +0200)]
arm: socfpga: vining: Set default SPI NOR mode and frequency
The SPI NOR bus mode is 0 on this system, update it accordingly.
Increase frequency to 40 MHz and enable SFDP parsing, since the
flashes on this system support that and it is a huge performance
improvement.
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Siew Chin Lim <elly.siew.chin.lim@intel.com> Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com> Cc: Tien Fong Chee <tien.fong.chee@intel.com>
Mark Kettenis [Thu, 16 Sep 2021 14:00:09 +0000 (16:00 +0200)]
usb: xhci-dwc3: Add support for USB 3.1 controllers
This adds support for the DWC_sub31 controllers such as those
found on Apple's M1 SoC. This version of the controller
seems to work fine with the existing driver.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Allow using different PHY interfaces for multiple USB controllers. When no
value is set in DT, we fall back to CONFIG_MXC_USB_PORTSC for now to stay
compatible with current board configurations.
This also adds support for the HSIC mode of the i.MX7.
Signed-off-by: Markus Niebel <Markus.Niebel@ew.tq-group.com> Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Samuel Holland [Mon, 5 Jul 2021 12:29:03 +0000 (13:29 +0100)]
usb: xhci-dwc3: Add support for clocks/resets
Some platforms, like the Allwinner H6, do not have a separate glue layer
around the dwc3. Instead, they rely on the clocks/resets/phys referenced
from the dwc3 DT node itself. Add support for enabling the clocks/resets
referenced from the dwc3 DT node.
Signed-off-by: Samuel Holland <samuel@sholland.org> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Samuel Holland [Mon, 5 Jul 2021 12:29:02 +0000 (13:29 +0100)]
usb: xhci-pci: Move reset logic out of XHCI core
Resetting an XHCI controller inside xhci_register undoes any register
setup performed by the platform driver. And at least on the Allwinner
H6, resetting the XHCI controller also resets the PHY, which prevents
the controller from working. That means the controller must be taken out
of reset before initializing the PHY, which must be done before calling
xhci_register.
The logic in the XHCI core was added to support the Raspberry Pi 4
(although this was not mentioned in the commit log!), which uses the
xhci-pci platform driver. Move the reset logic to the platform driver,
where it belongs, and where it cannot interfere with other platform
drivers.
This also fixes a failure to call reset_free if xhci_register failed.
Fixes: 0b80371b350e ("usb: xhci: Add reset controller support") Signed-off-by: Samuel Holland <samuel@sholland.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Samuel Holland [Mon, 5 Jul 2021 12:29:01 +0000 (13:29 +0100)]
phy: sun50i-usb3: Add a driver for the H6 USB3 PHY
This driver is needed for XHCI to work on the Allwinner H6 SoC. The
driver is copied from Linux v5.10.
Reviewed-by: Andre Przywara <andre.przywara@arm.com> Signed-off-by: Samuel Holland <samuel@sholland.org> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Andy Shevchenko [Sat, 11 Sep 2021 18:27:42 +0000 (21:27 +0300)]
x86: tangier: acpi: Add GPIO card detection to SDHCI #2
On Intel Tangier the SDHCI #2 provides SD card connection.
Add GPIO card detection for it.
Fixes: 39665beed6f7 ("x86: tangier: Enable ACPI support for Intel Tangier") BugLink: https://github.com/edison-fw/meta-intel-edison/issues/135 Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: Bin Meng <bmeng.cn@gmail.com>
Eugen Hristev [Thu, 19 Aug 2021 11:09:41 +0000 (14:09 +0300)]
board: atmel: sama7g5ek: avoid rewriting of configured CONFIG_BOOTCOMMAND
Rewrite the CONFIG_BOOTCOMMAND only if it's not previously configured from
defconfig file.
This allows the user to select from defconfig/menuconfig the desired
boot command.
Adjust the current board defconfigs to reflect the default booting command
for the specific ENV configuration.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Mihai Sain [Tue, 17 Aug 2021 10:29:25 +0000 (13:29 +0300)]
configs: sama5d2: add qspi config for QSPI1
Add new config for storing environment from QSPI1.
Signed-off-by: Mihai Sain <mihai.sain@microchip.com>
[eugen.hristev@microchip.com: cleanup and add MAINTAINERS entry] Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
projects / u-boot.git / log