Kever Yang [Tue, 7 Jan 2020 07:15:20 +0000 (15:15 +0800)]
ram: rk3328: only do data traning for cs0
No need to do twice data training for rk3328 ddr sdram, we re-use the
setting for both channel. And adjust the sdram_init properly for correct
init flow.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com> Signed-off-by: YouMin Chen <cym@rock-chips.com>
Jagan Teki [Thu, 9 Jan 2020 18:46:22 +0000 (00:16 +0530)]
doc: boards: Add rockchip documentation
Rockchip has documentation file, doc/README.rockchip but
which is not so readable to add or understand the existing
contents. Even the format that support is legacy readme
in U-Boot.
Add rockchip specific documentation file using new rst
format, which describes the information about Rockchip
supported boards and it's usage steps.
Added minimal information about rk3288, rk3328, rk3368
and rk3399 boards and usage. This would indeed updated
further based on the requirements and updates.
Cc: Kever Yang <kever.yang@rock-chips.com> Cc: Matwey V. Kornilov <matwey.kornilov@gmail.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Jagan Teki [Thu, 9 Jan 2020 18:46:21 +0000 (00:16 +0530)]
rockchip: Add Single boot image (with binman, pad_cat)
All rockchip platforms support TPL or SPL-based bootloader
in mainline with U-Boot proper as final stage. For each
stage we need to burn the image on to flash with respective
offsets.
This patch creates a single boot image component using
- binman, for arm32 rockchip platforms
- pad_cat, for arm64 rockchip platforms.
This would help users to get rid of burning different
boot stage images.
The new image called 'u-boot-rockchip.bin'
which can burn into flash like:
Jagan Teki [Thu, 9 Jan 2020 18:46:16 +0000 (00:16 +0530)]
Makefile: Add rockchip image type
Add rockchip image type support. right now the image
type marked with rksd, So create image type variable
with required image type like rksd or rkspi.
Cc: Matwey V. Kornilov <matwey.kornilov@gmail.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Jagan Teki [Thu, 9 Jan 2020 08:52:19 +0000 (14:22 +0530)]
rockchip: rk3399: Add bootcount support
Add bootcount support for Rockchip rk3399.
The bootcount value is preserved in PMU_SYS_REG0 register,
this would help to support redundent boot.
Once the redundant boot triggers, the altboot command
will look for extlinux-rollback.conf on particular
bootable partition which supposed to be a recovery
partition where redundant boot required.
Reviewed-by: Kever Yang <kever.yang@rock-chips.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Jagan Teki [Thu, 9 Jan 2020 08:52:17 +0000 (14:22 +0530)]
arm: rockchip: Add common cru.h
Few of the rockchip family SoC atleast rk3288,
rk3399 are sharing some cru register bits so
adding common code between these SoC families
would require to include both cru include files
that indeed resulting function declarations error.
So, create a common cru include as cru.h then
include the rk3399 arch cru include file and move
the common cru register bit definitions into it.
The rest of rockchip cru files will add it in future.
Reviewed-by: Kever Yang <kever.yang@rock-chips.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Jagan Teki [Sat, 21 Dec 2019 07:54:36 +0000 (13:24 +0530)]
env: Enable SPI flash env for rockchip
Most of the SPI flash devices in rockchip are 16MiB size.
So, keeping U-Boot proper offset start from 128MiB with 1MiB
size and then start env of 8KiB would be a compatible location
between all variants of flash sizes.
This patch add env start from 0x14000 with a size of 8KiB.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Thomas Hebb [Fri, 20 Dec 2019 20:28:15 +0000 (12:28 -0800)]
ram: rk3399: don't assume phy_io_config() uses real regs
In the RK3399 DRAM driver, the function set_ds_odt() supports operating
in two different modes, selected by the ctl_phy_reg argument: when true,
the function reads and writes directly from the DRAM registers, accessed
through "chan->pctl->denali_*"; when false, the function reads and
writes from an array, accessed through "params->pctl_regs.denali_*",
which is written to DRAM registers at a later time.
However, phy_config_io(), which is called by set_ds_odt() to do a subset
of its register operations, operates directly on DRAM registers at all
times. This means that it reads incorrect values (and writes new values
prematurely) when ctl_phy_reg in set_ds_odt() is false. Fix this by
passing in the address of the registers to work with.
This prevents an "Invalid DRV value" error in the SPL debug log and
(presumably) results in a more correct end state. See the following logs
from a RK3399 NanoPi M4 board (4GB LPDDR3):
Tom Rini [Wed, 29 Jan 2020 14:34:13 +0000 (09:34 -0500)]
Merge tag 'for-v2020.04' of https://gitlab.denx.de/u-boot/custodians/u-boot-i2c
i2c changes for 2020.04
- updates the Designware I2C driver
- get timings from device tree
- handle units in nanoseconds
- make sure that the requested bus speed is not exceeded
- few smaller clean-ups
- adds enums for i2c speed and update drivers which use them
- global_data: remove unused mxc_i2c specific field
Martin Fuzzey [Tue, 14 Jan 2020 15:56:18 +0000 (15:56 +0000)]
pmic: allow dump command for non contiguous register maps
Some PMICs (such as the DA9063) have non-contiguous register maps.
Attempting to read the non implemented registers returns an error
rather than a dummy value which causes 'pmic dump' to terminate
prematurely.
Fix this by allowing the PMIC driver to return -ENODATA for such
registers, which will then be displayed as '--' by pmic dump.
Use a single error code rather than any error code so that
we can distinguish between a hardware failure reading the PMIC
and a non implemented register known to the driver.
Signed-off-by: Martin Fuzzey <martin.fuzzey@flowbird.group>
Martin Fuzzey [Tue, 14 Jan 2020 15:56:17 +0000 (15:56 +0000)]
power: regulator: add driver for Dialog DA9063 PMIC
Add a driver for the regulators in the the DA9063 PMIC.
Robert Beckett: move regulator modes to header so board code can set
modes. Correct mode mask used in ldo_set_mode.
Add an option CONFIG_SPL_DM_REGULATOR_DA9063.
Signed-off-by: Martin Fuzzey <martin.fuzzey@flowbird.group> Signed-off-by: Robert Beckett <bob.beckett@collabora.com>
Martin Fuzzey [Tue, 14 Jan 2020 15:56:16 +0000 (15:56 +0000)]
power: pmic: add driver for Dialog DA9063 PMIC
This adds the basic register access operations and child regulator
binding (if a regulator driver exists).
Robert Beckett: simplify accesses by using bottom bit of address as
offset overflow. This avoids the need to track which page we are on.
Add an option CONFIG_SPL_DM_PMIC_DA9063.
Signed-off-by: Martin Fuzzey <martin.fuzzey@flowbird.group> Signed-off-by: Robert Beckett <bob.beckett@collabora.com>
Ian Ray [Tue, 14 Jan 2020 16:18:20 +0000 (16:18 +0000)]
rtc: s35392a: encode command correctly
The 3-bit "command", or register, is encoded within the device address.
Configure the device accordingly, and pass command in DM I2C read/write
calls correctly.
Signed-off-by: Ian Ray <ian.ray@ge.com> Signed-off-by: Robert Beckett <bob.beckett@collabora.com>
This can be used for device tree size reduction similar as
CONFIG_OF_SPL_REMOVE_PROPS option. Some boards must pass the
built-in DTB unchanged to the kernel, thus we may not cut it
down unconditionally. Therefore enable the property removal
list option only if CONFIG_OF_DTB_PROPS_REMOVE is selected.
Marek Szyprowski [Fri, 17 Jan 2020 13:02:44 +0000 (14:02 +0100)]
arm: exynos: Read default MMC device from XOM[7:5] pins
XOM pins provide information for iROM bootloader about the boot device.
Those pins are mapped to lower bits of OP_MODE register (0x10000008),
which is common for all Exynos SoC variants. Set the default MMC device id
to reflect the boot device selected by XOM[7:5] pins (2 for the SD or 0 for
the eMMC).
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
spi: cadence-qspi: Add support for Cadence Octal SPI controller
Cadence OSPI is similar to QSPI IP except that it supports Octal IO
(8 IO lines) flashes. Add support for Cadence OSPI IP with existing
driver using new compatible
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com> Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Add support for Direct Access Controller mode of Cadence QSPI. This
allows MMIO access to SPI NOR flash providing better read performance.
Direct mode is only exercised if AHB window size is greater than 8MB.
Support for flash address remapping is also not supported at the moment
and can be added in future.
For better performance, driver uses DMA to copy data from flash in
direct mode using dma_memcpy().
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com> Tested-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com> Acked-by: Jagan Teki <jagan@amarulasolutions.com>
Current Cadence QSPI driver has few limitations. It assumes all read
operations to be in Quad mode and thus does not support SFDP parsing.
Also, adding support for new mode such as Octal mode would not be
possible with current configuration. Therefore move the driver over to spi-mem
framework. This has added advantage that driver can be used to support
SPI NAND memories too.
Hence, move driver over to new spi-mem APIs.
Please note that this gets rid of mode bit setting done when
CONFIG_SPL_SPI_XIP is defined as there does not seem to be any user to
that config option.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com> Tested-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com> Acked-by: Jagan Teki <jagan@amarulasolutions.com>
Make sure corresponding setup registers are updated depending on CS.
This ensures that driver can support QSPI flashes on ChipSelects other
than on CS0
Reported-by: Andreas Dannenberg <dannenberg@ti.com> Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com> Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Marcin Wojtas [Thu, 21 Nov 2019 04:38:47 +0000 (05:38 +0100)]
spi: prevent overriding established bus settings
The SPI stack relies on a proper bus speed/mode configuration
by calling dm_spi_claim_bus(). However the hitherto code
allowed to accidentally override those settings in
the spi_get_bus_and_cs() routine.
The initially established speed could be discarded by using
the slave platdata, which turned out to be an issue on
the platforms whose slave maximum supported frequency
is not on par with the maximum frequency of the bus controller.
This patch fixes above issue by configuring the bus from
spi_get_bus_and_cs() only in case it was not done before.
Signed-off-by: Marcin Wojtas <mw@semihalf.com> Reviewed-by: Simon Glass <sjg@chromium.org> Acked-by: Jagan Teki <jagan@amarulasolutions.com>
Bin Meng [Mon, 9 Sep 2019 13:00:03 +0000 (06:00 -0700)]
test: dm: spi: Fix sandbox dm_test_spi_find()
Per sandbox_cs_info(), sandbox spi controller only supports chip
select 0. Current test case tries to locate devices on chip select
1, and any call to spi_get_bus_and_cs() or spi_cs_info() with cs
number 1 should not return 0.
This updates the test case to handle it correctly.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Michael Walle [Tue, 17 Dec 2019 23:09:58 +0000 (00:09 +0100)]
spi: nxp_fspi: new driver for the FlexSPI controller
This is a port of the kernel's spi-nxp-fspi driver. It uses the new
spi-mem interface and does not expose the more generic spi-xfer
interface. The source was taken from the v5.3-rc3 tag.
The port was straightforward:
- remove the interrupt handling and the completion by busy polling the
controller
- remove locks
- move the setup of the memory windows into claim_bus()
- move the setup of the speed into set_speed()
- port the device tree bindings from the original fspi_probe() to
ofdata_to_platdata()
There were only some style change fixes, no change in any logic. For
example, there are busy loops where the return code is not handled
correctly, eg. only prints a warning with WARN_ON(). This port
intentionally left most functions unchanged to ease future bugfixes.
This was tested on a custom LS1028A board. Because the LS1028A doesn't
have proper clock framework support, changing the clock speed was not
tested. This also means that it is not possible to change the SPI
speed on LS1028A for now (neither is it possible in the linux driver).
Signed-off-by: Michael Walle <michael@walle.cc> Reviewed-by: Jagan Teki <jagan@amarulasolutions.com> Tested-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Simon Glass [Thu, 23 Jan 2020 18:48:25 +0000 (11:48 -0700)]
i2c: designware_i2c: Separate out the speed calculation
We want to be able to calculate the speed separately from actually setting
the speed, so we can generate the required ACPI tables. Split out the
calculation into its own function.
Drop the double underscore on __dw_i2c_set_bus_speed while we are here.
That is reserved for compiler internals.
Simon Glass [Thu, 23 Jan 2020 18:48:24 +0000 (11:48 -0700)]
i2c: designware_i2c: Move dw_i2c_speed_config to header
This is used to store the speed information for a bus. We want to provide
this to ACPI so that it can tell the kernel. Move this struct to the
header file so it can be accessed by the ACPI i2c implementation being
added later.
Simon Glass [Thu, 23 Jan 2020 18:48:14 +0000 (11:48 -0700)]
i2c: designware_i2c: Rewrite timing calculation
At present the driver can end up with timing parameters which are slightly
faster than those expected. It is possible to optimise the parameters to
get the best possible result.
Create a new function to handle the timing calculation. This uses a table
of defaults for each speed mode rather than writing it in code.
The function works by calculating the 'period' of each bit on the bus in
terms of the input clock to the controller (IC_CLK). It makes sure that
the constraints are met and that the different components of that period
add up correctly.
This code was taken from coreboot which has ended up with this same
driver, but now in a much-different form.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Heiko Schocher <hs@denx.de>
Simon Glass [Thu, 23 Jan 2020 18:48:12 +0000 (11:48 -0700)]
i2c: designware_i2c: Drop scl_sda_cfg parameter
Instead of passing this parameter into __dw_i2c_set_bus_speed(), pass in
the driver's private data, from which the function can obtain that
information. This allows the function to have access to the full state of
the driver.
Simon Glass [Thu, 23 Jan 2020 18:48:07 +0000 (11:48 -0700)]
i2c: designware_i2c: Rename 'max' speed to 'high' speed
Some SoCs support a higher speed than what is currently called 'max' in
this driver. Rename it to 'high' speed, which is the official name of the
3.4MHz speed.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Jun Chen <ptchentw@gmail.com> Reviewed-by: Heiko Schocher <hs@denx.de>
Simon Glass [Thu, 23 Jan 2020 18:48:06 +0000 (11:48 -0700)]
i2c: designware_i2c: Include clk.h in the header file
We use struct clk here so really should include this header file to avoid
build errors. Also switch the order of clk.h in the C file to match the
required code style.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Ley Foon Tan <ley.foon.tan@intel.com> Reviewed-by: Jun Chen <ptchentw@gmail.com> Reviewed-by: Heiko Schocher <hs@denx.de>
Pedro Jardim [Thu, 23 Jan 2020 13:21:05 +0000 (10:21 -0300)]
clock_imx8mq: Remove the function sscg_pll_init()
Function sscg_pll_init() is not used anywhere, so it can simply be deleted.
This was found because of the following sparse
warning:
arch/arm/mach-imx/imx8m/clock_imx8mq.c:702:5: warning: no previous prototype for ‘sscg_pll_init’ [-Wmissing-prototypes]
int sscg_pll_init(u32 pll)
^~~~~~~~~~~~~
Signed-off-by: Pedro Jardim <jardim.c.pedro@gmail.com>
Pedro Jardim [Thu, 23 Jan 2020 13:20:51 +0000 (10:20 -0300)]
clock_imx8mq: Make do_imx8m_showclocks() static
Since do_imx8m_showclocks() is only used inside this file, make it 'static'.
This fixes the following sparse warning:
arch/arm/mach-imx/imx8m/clock_imx8mq.c:836:5: warning: no previous prototype
for ‘do_imx8m_showclocks’ [-Wmissing-prototypes]
int do_imx8m_showclocks(cmd_tbl_t *cmdtp, int flag, int argc,
^~~~~~~~~~~~~~~~~~~
Signed-off-by: Pedro Jardim <jardim.c.pedro@gmail.com>
Joel Johnson [Sun, 26 Jan 2020 16:48:58 +0000 (09:48 -0700)]
arm: mvebu: fix A38x breakage from commit bb872dd930cc
This function parameter usage of load_addr was incorrectly caught in
the clarifying renames of commit bb872dd930cc, which results in boot
failures on Marvell A38x.
Signed-off-by: Joel Johnson <mrjoel@lixil.net> Patch-to: Simon Glass <sjg@chromium.org>
Andre Przywara [Fri, 10 Jan 2020 01:47:32 +0000 (01:47 +0000)]
sunxi: Automate loading from 128KB MMC offset
Since commit 067e0b9684d4 ("sunxi: Allow booting from 128KB SD/eMMC offset")
we support having the SPL loaded from either the traditional 8KB SD
card/eMMC offset, or from the alternative location at 128KB. However the
sector to find the U-Boot image was still hard-coded at compile time,
and had to be adjusted for one of the two choices.
Since we can actually override the function to return the sector offset,
we can just check the boot source byte there to select the proper offset
based on from where the SPL was loaded.
This allows the very same binary image to be loaded from either 128KB or
8KB, with the U-Boot proper image always being located just behind the SPL.
Signed-off-by: Andre Przywara <andre.przywara@arm.com> Acked-by: Jagan Teki <jagan@amarulasolutions.com>
Andre Przywara [Fri, 10 Jan 2020 01:47:31 +0000 (01:47 +0000)]
sunxi: SPL: Factor out sunxi_get_boot_source()
The Boot ROM write some boot source ID (SD card, eMMC, SPI, ...) into
a certain location in SRAM, so the SPL can easily determine where to
load U-Boot proper from.
Factor out reading this value, as it will come in handy again shortly.
Signed-off-by: Andre Przywara <andre.przywara@arm.com> Acked-by: Jagan Teki <jagan@amarulasolutions.com>
Giulio Benetti [Thu, 12 Dec 2019 22:53:19 +0000 (23:53 +0100)]
clk: uclass: clk_get_by_name() must not be available if CONFIG_OF_PLATDATA is enabled
clk_get_by_name() requires clk_get_by_id() that is not available if
CONFIG_OF_PLATDATA is defined, so move clk_get_by_name() into #else
condition of #if CONFIG_IS_ENABLED(OF_PLATDATA).
Fabien Parent [Thu, 17 Oct 2019 19:02:05 +0000 (21:02 +0200)]
clk: mediatek: use unsigned type for returning the clk rate
mtk_clk_find_parent_rate is calling clk_get_rate to know the rate
of a parent clock. clk_get_rate returns a ulong, while
mtk_clk_find_parent_rate returns an int. This implicit cast creates
an issue for clock rates big enough to need the full 32 bits to
store its data. When that happen the clk rate will become incorrect
because of the implicit cast between ulong -> int -> ulong.
This commit change the return type of mtk_clk_find_parent_rate to
ulong.
projects / u-boot.git / log