Masahiro Yamada [Fri, 13 Oct 2017 10:21:51 +0000 (19:21 +0900)]
gpio: uniphier: rework single device node model
First, I implemented this driver as per-bank model, but it was
a design mistake.
- There are 31 banks in the maximum case. It is painful to add
so many nodes to DT.
- The IRQ control registers are shared between banks. Per-bank
design is a problem for Linux. The counterpart for Linux turned
around to the single node model.
mtd: nand: do not check R/B# for CMD_SET_FEATURES in nand_command(_lp)
Set Features (0xEF) command toggles the R/B# pin after 4 sub feature
parameters are written.
Currently, nand_command(_lp) calls chip->dev_ready immediately after
the address cycle because NAND_CMD_SET_FEATURES falls into default:
label. No wait is needed at this point.
If you see nand_onfi_set_features(), R/B# is already cared by the
chip->waitfunc call.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
[ Linux commit: c5d664aa5a4c4b257a54eb35045031630d105f49 ]
mtd: nand: do not check R/B# for CMD_READID in nand_command(_lp)
Read ID (0x90) command does not toggle the R/B# pin. Without this
patch, NAND_CMD_READID falls into the default: label, then R/B# is
checked by chip->dev_ready().
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
[ Linux commit: 3158fa0e739615769cc047d2428f30f4c3b6640e ]
Diego Dorta [Thu, 5 Oct 2017 12:15:58 +0000 (09:15 -0300)]
mx6: sys_proto: Add prototypes for imx6_pcie_toggle() functions
When compiling with W=1 errors are observed:
drivers/pci/pcie_imx.c:517:12: warning: no previous prototype for ‘imx6_pcie_toggle_power’ [-Wmissing-prototypes] __weak int imx6_pcie_toggle_power(void)
drivers/pci/pcie_imx.c:528:12: warning: no previous prototype for ‘imx6_pcie_toggle_reset’ [-Wmissing-prototypes] __weak int imx6_pcie_toggle_reset(void)
Remove these warnings by adding the functions prototypes on arch-mx6/sys_proto.
Diego Dorta [Thu, 5 Oct 2017 12:15:57 +0000 (09:15 -0300)]
mx6: clock: Add a prototype for do_mx6_showclocks()
When compiling with W=1 the following warning is observed:
arch/arm/mach-imx/mx6/clock.c:1268:5: warning: no previous prototype for ‘do_mx6_showclocks’ [-Wmissing-prototypes] int do_mx6_showclocks(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
Remove this warning by adding the function prototype into arch-mx6/clock.h file.
i.mx6ul: xpress: update UART init for current board revision
UART pinmux has been changed on the last board revision. Change
board pinmux accordingly. Console is on UART7 now, add pinmux,
base address and update console string in environment.
Fabio Estevam [Mon, 2 Oct 2017 13:11:37 +0000 (10:11 -0300)]
mx6slevk: Use PARTUUID to specify the rootfs location
mx6slevk can run different kernel versions, such as NXP 4.1 or mainline.
Currently the rootfs location is passed via mmcblk number and the
problem with this approach is that the mmcblk number for the SD
card changes depending on the kernel version.
In order to avoid such issue, use the UUID method to specify the
rootfs location.
Sven-Ola Tuecke [Thu, 5 Oct 2017 11:46:42 +0000 (08:46 -0300)]
drivers: pci: imx: fix imx_pcie_remove function
We have at least a minor count of boards, that failed to re-initialize
PCI express in the Linux kernel. Typical failure rate is 20% on affected
boards. This is mitigated by commit 6ecbe1375671 ("drivers: pci: imx:
add imx_pcie_remove function").
However, at least on some i.MX6 custom boards, when calling
assert_core_reset() as part of the first-time PCIe init, read access
to PCIE_PL_PFLR simply hangs. Surround this readl() with
imx_pcie_fix_dabt_handler() does not help. For this reason, the forced
LTSSM detection is only used on the second assert_core_reset() that is
called shorly before starting the Linux kernel.
The detection mechanism is to probe the PMIC and when it is
found, then the revision of the board is revd1.
As the detection is done via PMIC, we need to print the board version
at a later stage via CONFIG_DISPLAY_BOARDINFO_LATE and also need
to disable CONFIG_DISPLAY_BOARDINFO, which is done much earlier.
Make the necessary adjustments for the AR8035 PHY to work on revd1.
Based on Richard Hu's work from Technexion's U-Boot tree.
Stefan Agner [Tue, 3 Oct 2017 14:43:26 +0000 (16:43 +0200)]
doc: update imx_usb_loader URL
The changes required to use U-Boot's Serial Download Protocol
implementation are now available in upstream imx_usb_loader
repository. Update the URL accordingly.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com> Reviewed-by: Tom Rini <trini@konsulko.com>
Uri Mashiach [Sun, 24 Sep 2017 06:00:23 +0000 (09:00 +0300)]
imx: mx7: DDR controller configuration for the i.MX7 architecture
The configuration files imximage.cfg are used for the DDR controller
configuration.
Add DDR configuration function to replace the DDR controller
configuration in the imximage.cfg file. The function can be used for
DDR size detection.
Signed-off-by: Uri Mashiach <uri.mashiach@compulab.co.il>
Diego Dorta [Wed, 27 Sep 2017 16:12:40 +0000 (13:12 -0300)]
mx6sabresd: Include <usb/ehci-ci.h> header file
When compiling with W=1 the following warning is observed:
board/freescale/mx6sabresd/mx6sabresd.c:586:5: warning: no previous prototype for ‘board_ehci_hcd_init’ [-Wmissing-prototypes] int board_ehci_hcd_init(int port)
Diego Dorta [Wed, 27 Sep 2017 16:12:39 +0000 (13:12 -0300)]
usb: ehci-ci: Add a prototype for board_ehci_power()
When compiling with W=1 the following warning is observed:
board/freescale/mx6sabresd/mx6sabresd.c:601:5: warning: no previous prototype for ‘board_ehci_power’ [-Wmissing-prototypes] int board_ehci_power(int port, int on)
Remove this warning by adding the function prototype into usb/ehci-ci.h file.
Diego Dorta [Wed, 27 Sep 2017 16:12:38 +0000 (13:12 -0300)]
mx6sabresd: Include <asm/mach-imx/spi.h> header file
When compiling with W=1 the following warning is observed:
board/freescale/mx6sabresd/mx6sabresd.c:680:5: warning: no previous prototype for ‘board_spi_cs_gpio’ [-Wmissing-prototypes] int board_spi_cs_gpio(unsigned bus, unsigned cs)
Remove this warning by including <asm/mach-imx/spi.h>.
Diego Dorta [Thu, 21 Sep 2017 18:10:03 +0000 (15:10 -0300)]
imx: sys_proto: Add a prototype for board_mmc_get_env_dev()
When compiling with W=1 the following warning is observed:
board/freescale/mx6sabresd/mx6sabresd.c:266:5: warning:
no previous prototype for ‘board_mmc_get_env_dev’
[-Wmissing-prototypes] int board_mmc_get_env_dev(int devno)
Remove this warning by adding the function prototype into sys_proto.h file.
Diego Dorta [Fri, 22 Sep 2017 15:12:18 +0000 (12:12 -0300)]
imx: Include <input.h> header file
When building with W=1 errors like the one below is seen:
board/freescale/mx6sabresd/mx6sabresd.c:546:5: warning:
no previous prototype for ‘overwrite_console’
[-Wmissing-prototypes] int overwrite_console(void)
Fix the build warnings by including <input.h>.
Signed-off-by: Diego Dorta <diego.dorta@nxp.com> Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Rob Clark [Tue, 10 Oct 2017 12:23:01 +0000 (08:23 -0400)]
efi_loader: console support for color attributes
Shell.efi uses this, and supporting color attributes makes things look
nicer. Map the EFI fg/bg color attributes to ANSI escape sequences.
Not all colors have a perfect match, but spec just says "Devices
supporting a different number of text colors are required to emulate the
above colors to the best of the device’s capabilities".
Signed-off-by: Rob Clark <robdclark@gmail.com> Tested-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Reviewed-by: Alexander Graf <agraf@suse.de>
[agraf: s/unsigned/unsigned int/] Signed-off-by: Alexander Graf <agraf@suse.de>
Rob Clark [Tue, 10 Oct 2017 12:23:06 +0000 (08:23 -0400)]
efi_loader: Add mem-mapped for fallback
When we don't have a real device/image path, such as 'bootefi hello',
construct a mem-mapped device-path.
This fixes 'bootefi hello' after devicepath refactoring.
Fixes: 95c5553ea2 ("efi_loader: refactor boot device and loaded_image handling") Signed-off-by: Rob Clark <robdclark@gmail.com> Acked-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Signed-off-by: Alexander Graf <agraf@suse.de>
Chris Packham [Thu, 28 Sep 2017 21:53:36 +0000 (10:53 +1300)]
i2c: muxes: pca954x: look up width from chip_desc
Commit 8e6eda7cda6c ("drivers/i2c/muxes/pca954x: Add pca9547 I2C mux
support") introduced a chip_desc for the pca954x devices but failed to
update pca954x_ofdata_to_platdata() to be aware of it. Make
pca954x_ofdata_to_platdata() lookup the chip_desc to validate the device
width.
Signed-off-by: Chris Packham <judge.packham@gmail.com> Reviewed-by: Marek Behun <marek.behun@nic.cz>
The option is specified in Kconfig, but still a few config header files
are overriding the choice by #undef'ing it. Re-sync the option with
moveconfig to rid of the #undefs.
Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
Having this as a 'default y' is rather annoying because it doesn't
actually compile unless other options are defined in the board header:
../cmd/bootm.c: In function 'do_imls_nor':
../cmd/bootm.c:330:7: error: 'CONFIG_SYS_MAX_FLASH_BANKS' undeclared (first use in this function); did you mean 'CONFIG_SYS_MAX_FLASH_SECT'?
i < CONFIG_SYS_MAX_FLASH_BANKS; ++i, ++info) {
Make it 'default n' so people who develop new boards that start from a
blank defconfig have one less compilation failure to debug.
Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
The constant MAX_UTF8_PER_UTF16 is used to calculate
required memory when converting from UTF-16 to UTF-8.
If this constant is too big we waste memory.
A code point encoded by one UTF-16 symbol is converted to a
maximum of three UTF-8 symbols, e.g.
0xffff could be encoded as 0xef 0xbf 0xbf.
The first byte carries four bits, the second and third byte
carry six bits each.
A code point encoded by two UTF-16 symbols is converted to four
UTF-8 symbols.
So in this case we need a maximum of two UTF-8 symbols per
UTF-16 symbol.
As the overall maximum is three UTF-8 symobls per UTF-16 symbol
we need MAX_UTF8_PER_UTF16 = 3.
Fixes: 78178bb0c9d lib: add some utf16 handling helpers Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Signed-off-by: Alexander Graf <agraf@suse.de>
Jonathan Gray [Tue, 10 Oct 2017 02:55:26 +0000 (13:55 +1100)]
efi_loader: search all possible disk partitions
When searching for partitions don't stop if a partition is not present
for a given partition number as there may be valid partitions after.
Search for up to MAX_SEARCH_PARTITIONS matching the other callers of
part_get_info().
This allows OpenBSD to boot via the efi_loader on rpi_3 again after
changes made after U-Boot 2017.09. With MBR partitioning OpenBSD will
by default use the fourth partition for the 0xA6 (OpenBSD) partition.
Signed-off-by: Jonathan Gray <jsg@jsg.id.au> Signed-off-by: Alexander Graf <agraf@suse.de>
Marek Vasut [Wed, 4 Oct 2017 01:03:50 +0000 (03:03 +0200)]
ARM: rmobile: Fixup ULCB CPLD support after PFC rework
The ULCB CPLD support was not updated during the PFC table rework,
fix up the GPIO numbers until the CPLD support is rewritten to a
proper DM capable and DT probing driver.
York Sun [Thu, 28 Sep 2017 15:42:16 +0000 (08:42 -0700)]
armv8: ls1043ardb_sdcard: prepare falcon boot
Due to a conflict with recent Primary Protected Application (PPA),
PPA cannot be loaded for SPL stage, falcon boot is not enabled by
default. With compatible PPA image, to enable falcon boot, activate
these Kconfig options in defconfig
CONFIG_SPL_FIT=y
CONFIG_SPL_FSL_LS_PPA=y
CONFIG_SPL_GZIP=y
CONFIG_SPL_LOAD_FIT=y
CONFIG_SPL_OS_BOOT=y
CONFIG_SPL_OF_LIBFDT=y
Because environment variables are not avaiable during SPL stage for
SD boot, set "boot_os=y" as default.
Signed-off-by: York Sun <york.sun@nxp.com> Reviewed-by: Simon Glass <sjg@chromium.org>
York Sun [Thu, 28 Sep 2017 15:42:12 +0000 (08:42 -0700)]
armv8: fsl-layerscape: Avoid running dram_init_banksize again
gd->ram_size is reduced in this function to reserve secure memory.
Avoid running this function again to further reduce memory size.
This fixes issue for SPL boot with PPA image loaded in which case
secure memory is incorrectly allocated due to repeated calling.
Signed-off-by: York Sun <york.sun@nxp.com> Reviewed-by: Simon Glass <sjg@chromium.org>
York Sun [Thu, 28 Sep 2017 15:42:11 +0000 (08:42 -0700)]
cmd: spl: fix compiling error when CONFIG_CMD_SPL_WRITE_SIZE not defined
CONFIG_CMD_SPL_WRITE_SIZE is used for writing parameters to non-volatile
storage. So far it is only used for NAND. Fix compiling error when this
macro is not used for SD.
Signed-off-by: York Sun <york.sun@nxp.com> CC: Anatolij Gustschin <agust@denx.de>
York Sun [Thu, 28 Sep 2017 15:42:10 +0000 (08:42 -0700)]
spl: fix assignment of board info to global data
Commit 15eb1d43bf47 ("spl: reorder the assignment of board info to
global data") intended to move assignment of board info earlier,
into board_init_r(). However, function preload_console_init() is
called either from spl_board_init() or from board_init_f(). For the
latter case, the board info assignment is much earlier than proposed
board_init_r(). Create a new function to fill gd->bd and call this
function when needed.
Signed-off-by: York Sun <york.sun@nxp.com> CC: Lokesh Vutla <lokeshvutla@ti.com> CC: Ravi Babu <ravibabu@ti.com> CC: Lukasz Majewski <lukma@denx.de> CC: Tom Rini <trini@konsulko.com> Reviewed-by: Simon Glass <sjg@chromium.org>
The MC boot sequence is contained in mc_env_boot. Update LS1088A
boards to use this function, and hook it to reset_phy so that it's
called late enough, after the ports have been initialized, for
proper DPC / DPL fixup.
Signed-off-by: Bogdan Purcareata <bogdan.purcareata@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
Sumit Garg [Tue, 3 Oct 2017 21:50:49 +0000 (03:20 +0530)]
armv8: fsl-layerscape: Allocate Secure memory from first ddr region
This change is required due to trusted OS (OP-TEE) not being position
independent code, it requires compile time fixed base address.
To take care of this it is assumed that all layerscape armv8 platforms
has minimum 2G ddr in first region. So we can have fixed address
space (66 MB -> (2MB for PPA + 64MB for trusted OS)) allocated from
top of first 2G ddr region and compile trusted OS with this fixed
base address.
But one exception here is ls1012 where we have only 1G (rdb) or 512M
(frdm) ddr memory. For those we can have different fixed compile time
base addresses for trusted OS.
Signed-off-by: Sumit Garg <sumit.garg@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
Gong Qianyu [Mon, 18 Sep 2017 08:59:28 +0000 (16:59 +0800)]
armv8: ls1046aqds: Fix NAND offset for Fman ucode and env
Fix a bug of 'commit 8104deb2d6b7 ("armv8: layerscape: Adjust memory
mapping for Flash/SD card on LS1046A")' as NAND block size is 256KB
on LS1046AQDS.
Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
Rob Clark [Sun, 8 Oct 2017 15:33:08 +0000 (11:33 -0400)]
efi_loader: Fix disk dp's for pre-DM/legacy devices
This fixes an issue with OpenBSD's bootloader, and I think should also
fix a similar issue with grub2 on legacy devices. In the legacy case
we were creating disk objects for the partitions, but not also the
parent device.
Reported-by: Jonathan Gray <jsg@jsg.id.au> Signed-off-by: Rob Clark <robdclark@gmail.com> Signed-off-by: Alexander Graf <agraf@suse.de>
efi_selftest: avoid dereferencing NULL in tpl test
The task priority levels test uses two events one passes the
notification counter as context. The other passes NULL.
Both use the same notification function. So we need to check
for NULL here.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Alexander Graf <agraf@suse.de>
efi_selftest: efi_st_memcmp return difference of bytes
If the memory regions are different efi_st_memcmp currently
returns the difference of the addresses. Insted the
difference of the first differing byte pair should be
returned.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Signed-off-by: Alexander Graf <agraf@suse.de>
This patch provides an EFI application to check the correct function
of the Simple Network Protocol implementation.
It sends a DHCP request and analyzes the DHCP offer.
Different error conditions including a 10s timeout are checked.
A successful execution will look like this:
=> bootefi nettest
Scanning disk ide.blk#0...
Found 1 disks
WARNING: Invalid device tree, expect boot to fail
Network test
DHCP Discover
DHCP reply received from 192.168.76.2 (52:55:c0:a8:4c:02)
as broadcast message.
OK. The test was completed successfully.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Alexander Graf <agraf@suse.de>
The WaitForPacket event informs that a network package has been
received by the SimpleNetworkProtocol.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
[agraf: Move is_signaled = true line into efi_net_push()] Signed-off-by: Alexander Graf <agraf@suse.de>
A timer event is defined. The timer handler cares for receiving new
packets.
efi_timer_check is called both in efi_net_transmit and efi_net_receive
to enable events during network communication.
Calling efi_timer_check in efi_net_get_status is implemented in a
separate patch.
[agraf] This patch is needed to make efi_net_get_status() actually
report incoming packets.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
[agraf: fix spelling in comment] Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Alexander Graf <agraf@suse.de>
U-Boot does not implement all functions of the simple network
protocol. The unimplemented functions return either of
EFI_SUCCESS and EFI_INVALID_PARAMETER.
The UEFI spec foresees to return EFI_UNSUPPORTED in these cases.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Alexander Graf <agraf@suse.de>
The UEFI spec defines parameter index of WaitForEvent as UINTN*.
So we should use size_t here.
I deliberately do not use UINTN because I hold a following patch
that will eliminate UINTN because uppercase types to not match
the U-Boot coding style.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Alexander Graf <agraf@suse.de>
Rename counter to more illustrative names.
Update notification function description.
Simplify notification function.
Add comment for arbitrary non-zero value.
Document @return.
Use constants for return values of setup, execute, teardown.
Reported-by: Simon Glass <sjg@chromium.org> Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Alexander Graf <agraf@suse.de>
Queued and signaled describe boolean states of events.
So let's use type bool and rename the structure members to is_queued
and is_signaled.
Update the comments for is_queued and is_signaled.
Reported-by: Simon Glass <sjg@chromium.org> Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Reviewed-by: Rob Clark <robdclark@gmail.com> Reviewed-by: Rob Clark <robdclark@gmail.com> Signed-off-by: Alexander Graf <agraf@suse.de>
efi_selftest: use efi_st_error for all error messages
All error messages in the selftests should use efi_st_error.
efi_st_error will print the file name and line number of the error.
Splitting message texts due to lines being over 80
characters is avoided. This resolves the issue reported
by Simon Glass in
https://lists.denx.de/pipermail/u-boot/2017-September/307387.html
Reported-by: Simon Glass <sjg@chromium.org> Fixes: 623b3a579765 efi_selftest: provide an EFI selftest application Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Alexander Graf <agraf@suse.de>
Klaus Goger [Wed, 20 Sep 2017 11:50:41 +0000 (13:50 +0200)]
dm: ofnode: query correct property in livetree ofnode_get_addr_size
The livetree codepath of ofnode_get_addr_size always used the "reg"
property for of_get_property. Use the property parameter of the function
call instead and check the return value if the property exists.
Otherwise return FDT_ADDR_T_NONE.
This was discoverd while using SPI NOR with livetree.
spi_flash_decode_fdt checks for memory-map and will not fail with
livetree even if the property does not exist.
Signed-off-by: Klaus Goger <klaus.goger@theobroma-systems.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Simon Glass <sjg@chromium.org>
projects / u-boot.git / log