Lukasz Majewski [Sat, 26 Dec 2020 00:09:02 +0000 (01:09 +0100)]
xea: config: Disable CONFIG_SPL_OF_PLATDATA_PARENT on XEA (imx28)
On the XEA board (imx28) one needs in the SPL support for GPIO, MMC and
SPI. Two last ones are necessary for booting the device. The GPIO support
allows deciding which medium will be used. For example the GPIO DTS node
(gpio@0 at imx28.dtsi) has pinctrl parent (pinctrl@80018000) for which we
don't need driver asigned for correct operation.
In the spl/dts/dt-platdata.c the gpio@0 has index 4 and its parent -
pinctrl@80018000 has index 5.
In the bind_drivers_pass() function (at drivers/core/lists.c) call to
device_bind_by_name() for `fsl_imx23_pinctrl` returns -2, which is
expected.
With current setup - when the SPL_OF_PLATDATA_PARENT=y
The gpio@0 node with index 4 is skipped as its parent with 5 is not yet
bound. It cannot be as we don't need and provide the driver for it.
As a result the gpio@0 is never bound and we end up with bricked board in
the SPL stage.
When CONFIG_SPL_OF_PLATDATA_PARENT is NOT set, all entries from
spl/dts/dt-platdata.c are scanned in ascending index order, so gpio@0 is
properly initialized. For `fsl_imx_pinctrl` we simply check 10 times if
the driver for is available (which is not) and exit.
As a result the GPIOs are initialized and can be used in early SPL stage.
This commit fixes XEA regression introduced with e41651fffda7da55f6.
Signed-off-by: Lukasz Majewski <lukma@denx.de> Reviewed-by: Simon Glass <sjg@chromium.org>
Lukasz Majewski [Sat, 26 Dec 2020 00:09:01 +0000 (01:09 +0100)]
xea: config: Use CONFIG_PREBOOT from Kconfig
The usage of the preboot feature is now controlled via a separate Kconfig
option - namely CONFIG_USE_PREBOOT.
It must be enabled for preboot code executing commands now defined in
CONFIG_PREBOOT (also moved to the Kconfig).
After defining both CONFIG_USE_PREBOOT and CONFIG_PREBOOT in
imx28_xea_defconfig the define of CONFIG_PREBOOT shall be removed from
xea.h as it is redundant.
Hugh Cole-Baker [Sun, 22 Nov 2020 13:03:44 +0000 (13:03 +0000)]
rockchip: pinebook-pro: default to SPI bus 1 for SPI-flash
SPI flash on this machine is located on bus 1, default to using bus 1
for SPI flash and stop aliasing it to bus 0.
Signed-off-by: Hugh Cole-Baker <sigmaris@gmail.com> Suggested-by: Simon Glass <sjg@chromium.org> Fixes: c4cea2bb ("rockchip: Enable building a SPI ROM image on bob")
Marek Vasut [Sat, 2 Jan 2021 16:44:47 +0000 (17:44 +0100)]
ARM: dts: stm32: Fix GPIO hog flags on DHCOM DRC02
The GPIO hog flags are ignored by gpiolib-of.c now, set the flags to 0.
Since GPIO_ACTIVE_HIGH is defined as 0, this change only increases the
correctness of the DT.
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Patrice Chotard <patrice.chotard@st.com> Cc: Patrick Delaunay <patrick.delaunay@st.com> Reviewed-by: Patrice Chotard <patrice.chotard@st.com> Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Marek Vasut [Sat, 2 Jan 2021 16:44:46 +0000 (17:44 +0100)]
ARM: dts: stm32: Fix GPIO hog flags on DHCOM PicoITX
The GPIO hog flags are ignored by gpiolib-of.c now, set the flags to 0.
Due to a change in gpiolib-of.c, setting flags to GPIO_ACTIVE_LOW and
using output-low DT property leads to the GPIO being set high instead.
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Patrice Chotard <patrice.chotard@st.com> Cc: Patrick Delaunay <patrick.delaunay@st.com> Reviewed-by: Patrice Chotard <patrice.chotard@st.com> Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Pali Rohár [Sat, 21 Nov 2020 22:30:11 +0000 (23:30 +0100)]
Nokia RX-51: Decrease i2c speed to 100000
It looks like that i2c bus lot of times timeout on some units. Prior
migration to CONFIG_DM_I2C i2c speed was set to CONFIG_SYS_OMAP24_I2C_SPEED
value which was 100000. Lower speed fixes timeout problems, so change speed
back to its previous value.
Signed-off-by: Pali Rohár <pali@kernel.org> Fixes: 8d8c18170325 ("Nokia RX-51: Convert to CONFIG_DM_I2C") Reviewed-by: Pavel Machek <pavel@ucw.cz> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Philippe Reynes [Wed, 23 Dec 2020 14:33:07 +0000 (15:33 +0100)]
cmd: ubi: don't allow to rename a volume to a name that already exist
This commits add a check on the command ubi rename. This check avoids
to rename a volume to with a name that is already used on another ubi
volume. If two volumes has the same name, then the ubi device can't be
mounted anymore.
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
Stefan Agner [Wed, 30 Dec 2020 12:16:36 +0000 (13:16 +0100)]
nvme: Use only 32-bit accesses in nvme_writeq/nvme_readq
There might be hardware configurations where 64-bit data accesses
to NVMe registers are not supported properly. This patch removes
the readq/writeq so always two 32-bit accesses are used to read/write
64-bit NVMe registers, similarly as it is done in Linux kernel.
This patch fixes operation of NVMe devices on RPi4 Broadcom BCM2711 SoC
based board, where the PCIe Root Complex, which is attached to the
system through the SCB bridge.
Even though the architecture is 64-bit the PCIe BAR is 32-bit and likely
the 64-bit wide register accesses initiated by the CPU are not properly
translated to a sequence of 32-bit PCIe accesses.
nvme_readq(), for example, always returns same value in upper and lower
32-bits, e.g. 0x3c033fff3c033fff which lead to NVMe devices to fail
probing.
This fix is analogous to commit 8e2ab05000ab ("usb: xhci: Use only
32-bit accesses in xhci_writeq/xhci_readq").
Cc: Sylwester Nawrocki <s.nawrocki@samsung.com> Cc: Nicolas Saenz Julienne <nsaenzjulienne@suse.de> Cc: Matthias Brugger <mbrugger@suse.com> Reviewed-by: Stefan Roese <sr@denx.de> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Signed-off-by: Stefan Agner <stefan@agner.ch>
This change revers code which asserting PERST# signal when unloading
driver. Driver's remove callback is still there as it is used for other
functionality.
Asserting PERST# signal prior booting kernel is causing that A3720 boards
(Turris MOX and Espressobin) with stable Linux kernel versions 4.14 and
4.19 are not able to detect some PCIe cards (e.g. Compex WLE200 and WLE900)
and anymore. When PERST# signal is not asserted these cards are detected
correctly. As this is regression for existing stable Linux kernel versions
revert this problematic change in U-Boot.
To make cards working with OpenWRT 4.14 kernel it is needed to disable link
training prior booting kernel, which is already done in driver's remove
callback.
Described issue is in Linux kernel pci aardvark driver which is (hopefully)
fixed in latest upstream versions. Latest upstream versions should be able
to initialize PCIe bus and detects cards independently of the link training
and PERST# signal state.
So with this change, U-Boot on A3720 boards should be able to boot OpenWRT
4.14 kernel, stable 4.14 and 4.19 kernels and also latest mainline kernels.
Signed-off-by: Pali Rohár <pali@kernel.org> Reviewed-by: Stefan Roese <sr@denx.de>
Stefan Roese [Thu, 10 Dec 2020 05:40:10 +0000 (06:40 +0100)]
arm: mvebu: Add armada-xp-gp-u-boot.dtsi for U-Boot properties
Add some missing "u-boot,dm-pre-reloc;" properties to UART0, SPI
controller and SPI NOR flash node to enable usage in SPL. Otherwise
these devices will not be available.
Signed-off-by: Stefan Roese <sr@denx.de> Cc: Dennis Gilmore <dgilmore@redhat.com> Tested-by: Dennis Gilmore <dgilmore@redhat.com>
Marc Ferland [Tue, 22 Dec 2020 19:24:12 +0000 (14:24 -0500)]
arm: dart6ul: read and print SoM info from eeprom on startup
The dart6ul has an i2c eeprom at 0x50 which contains, among other
things, the manufacturing/revision/options info of the SoM. This patch
replaces the current checkboard() implementation with a more
exhaustive one based on the content of the eeprom.
Since this code uses the new driver model, some changes were also
required in the DTS to make the nodes related to i2c available before
relocation.
This code was inspired from the supported u-boot code from Variscite
which can be found here:
Igor Opaniuk [Tue, 22 Dec 2020 15:56:46 +0000 (17:56 +0200)]
toradex: hand over maintainership
Hand over maintainership of Toradex SoMs (that I was responsible of) to
Oleksandr because of my resignation from Toradex, as such I will
have no immediate involvement with these modules and as a result not
able to continue maintaining these boards.
1. Configure 125MHz clock
2. Setup the TX clock delay (RX is enabled by default),
3. Setup reserved bits to avoid voltage peak
The clock delays are nowadays already configured by the
PHY driver (in ar803x_delay_config). The code for that
can simply be dropped. The clock speed can also be
configured by the PHY driver by adding the device tree
property "qca,clk-out-frequency".
What is left is setting up the undocumented reserved bits
to avoid the voltage peak problem. I slightly improved its
documentation while updating the board's PHY rework code.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Instead of hardcoding index magic numbers in the board code,
also rely on board_fit_config_name_match choosing the right
config for the fitImage containing the kernel.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Ilias Apalodimas [Wed, 23 Dec 2020 11:25:00 +0000 (13:25 +0200)]
efi_loader: Extra checks while opening an OPTEE session
When opening an OP-TEE session we need to check the internal return
value of OP-TEE call arguments as well the return code of the
function itself.
The code was also ignoring to close the OP-TEE session in case the
shared memory registration failed.
Fixes: f042e47e8fb43 ("efi_loader: Implement EFI variable handling via OP-TEE") Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org> Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Add a host_build() function, so that it's possible to
check for software being build with USE_HOSTCC without
relying on preprocessor conditions. In other words
#ifdef USE_HOSTCC
host_only_code();
#endif
can be written like this instead:
if (host_build())
host_only_code();
This improves code readability and test coverage and
compiler will eleminate this unreachable code.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com> Reviewed-by: Simon Glass <sjg@chromium.org>
configs: imx8m: enable eMMC HS400ES and SD UHS mode on EVK
i.MX8M series includes support for high speed modes in uSDHC controllers.
Turn on corresponding configuration options for EVK boards, which would
enable high speed modes to be included in U-Boot.
ARM: dts: imx8m: increase off-on delay on the SD Vcc regulator
Some SD Card controller and power circuitry has increased capacitance,
which keeps the internal logic remains powered after regulator is switch
off. This is generally the case when card is switched to SD104 mode,
where a power cycle should be performed. In case if the card internal
logic remains powered, it causes a subsequent failure of mode
transition, effectively leading to failed enumeration.
Introduce a delay of 20 msec in order to provide a possibility for
internal card circuitry to drain voltages and perform a power cycle
correctly.
Similar fix is done in commit c49d0ac38a76 ("ARM: dts: rmobile: Increase
off-on delay on the SD Vcc regulator") targeted Renesas SOCs.
Adam Ford [Fri, 4 Dec 2020 23:27:46 +0000 (17:27 -0600)]
arm: dts: imx8mm: sync dts from Linux Kernel 5.10-rc6
There have been some updates to the device tree since 5.6.
This also includes some clocks, and makes it easier to keep
board device tree files in sync with Linux
Signed-off-by: Adam Ford <aford173@gmail.com> Acked-by: Peng Fan <peng.fan@nxp.com>
As per kernel commit 0672d22a1924 ("ARM: dts: imx: Fix the AR803X phy-mode)
the correct phy-mode should be "rgmii-id", so fix it accordingly
to fix the Ethernet regression.
Sughosh Ganu [Mon, 14 Dec 2020 06:22:44 +0000 (11:52 +0530)]
fsp: Move and rename fsp_types.h file
The fsp_types.h header file contains macros for building signatures of
different widths. These signature macros are architecture agnostic,
and can be used in all places which use signatures in a data
structure. Move and rename the fsp_types.h under the common include
header.
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tom Rini [Wed, 16 Dec 2020 00:06:03 +0000 (19:06 -0500)]
Travis-CI: Drop support
Travis-CI is changing their support for FOSS (understandably) to have a
limited per-month number of build minutes. Unfortunately for us, the
matrix of jobs we run will exhaust that very quickly. Remove the yml
file. Thanks for all the builds, Travis-CI!
Signed-off-by: Tom Rini <trini@konsulko.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Michael Walle [Sun, 20 Dec 2020 21:35:13 +0000 (22:35 +0100)]
board: kontron: sl28: reorder mmc devices
Since linux commit 2e6cde96873253fd9eb0f20afd8ffd18278cff75 ("arm64:
dts: ls1028a: make the eMMC and SD card controllers use fixed indices")
mmc0 is the eMMC and mmc1 is the SD card. Also swap it in u-boot to
avoid any confusion by the user and to be aligned with linux.
Tom Rini [Sun, 20 Dec 2020 19:55:59 +0000 (14:55 -0500)]
Merge tag 'efi-2021-01-rc4' of https://gitlab.denx.de/u-boot/custodians/u-boot-efi
Pull request for UEFI sub-system for efi-2021-01-rc4
* Provide a tool to create a file with UEFI variables to preseed UEFI
variable store.
* Make size of UEFI variable store configurable.
* Add man pages for commands 'bootefi' and 'button'.
Marek Szyprowski [Fri, 18 Dec 2020 10:43:45 +0000 (11:43 +0100)]
ARM: dts: meson: switch TFLASH_VDD_EN pin to open drain on Odroid-C4
For the proper reboot Odroid-C4 board requires to switch TFLASH_VDD_EN
pin to the high impedance mode, otherwise the board is stuck in the
middle of loading early stages of the bootloader from SD card.
This can be achieved by using the OPEN_DRAIN flag instead if the
ACTIVE_HIGH, what will leave the pin in input to achieve high state (pin
has the pull-up) and solve the issue.
Suggested-by: Neil Armstrong <narmstrong@baylibre.com> Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com> Acked-by: Neil Armstrong <narmstrong@baylibre.com> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Add SPI Flash controller driver for Cortina Access
CAxxxx SoCs
Signed-off-by: Pengpeng Chen <pengpeng.chen@cortina-access.com> Signed-off-by: Alex Nemirovsky <alex.nemirovsky@cortina-access.com> CC: Vignesh R <vigneshr@ti.com> CC: Tom Rini <trini@konsulko.com>
[jagan: rebase on master] Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Sean Anderson [Fri, 16 Oct 2020 22:57:53 +0000 (18:57 -0400)]
spi: dw: Add mem_ops
The designware ssi device has "broken" chip select behaviour [1], and needs
specific manipulation to use the built-in chip select. The existing fix is
to use an external GPIO for chip select, but typically the K210 has SPI3
directly connected to a flash chip with dedicated pins. This makes it
impossible to use the spi_xfer function to use spi, since the CS is
de-asserted in between calls. This patch adds an implementation of
exec_op, which gives correct behaviour when reading/writing spi flash.
This patch also rearranges the headers to conform to U-Boot style.
[1] https://lkml.org/lkml/2015/12/23/132
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Tested-by Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com> Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Sean Anderson [Fri, 16 Oct 2020 22:57:52 +0000 (18:57 -0400)]
spi: dw: Document devicetree binding
This documentation has been taken from Linux commit 3d7db0f11c7a ("spi: dw:
Refactor mid_spi_dma_setup() to separate DMA and IRQ config"), immediately
before the file was deleted and replaced with a yaml version. Additional
compatible strings from newer versions have been added, as well as a few
U-Boot-specific ones.
Signed-off-by: Sean Anderson <seanga2@gmail.com> Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Sean Anderson [Fri, 16 Oct 2020 22:57:51 +0000 (18:57 -0400)]
spi: dw: Add support for multiple CTRLR0 layouts
CTRLR0 can have several different layouts depending on the specific device
(dw-apb-ssi vs dwc-ssi), and specific parameters set during synthesis.
Update the driver to support three specific configurations: dw-apb-ssi with
SSI_MAX_XFER_SIZE=16, dw-apb-ssi with SSI_MAX_XFER_SIZE=32, and dwc-ssi.
dw-apb-ssi is the version of the device on Altera/Intel SoCFPGAs, MSCC
SoCs, and Canaan Kendryte K210 SoCs. This is the only version this driver
supported before this change. The register layout before version 3.23a is:
Note that DFS (Data Frame Size) is only 4 bits, limiting transfers to data
frames of 16 bits or less.
In version 3.23a, the SSI_MAX_XFER_SIZE parameter was introduced. This
parameter defaults to 16 (resulting in the same layout as prior versions),
but may also be set to 32. To allow setting longer data frame sizes, a new
DFS_32 register was introduced:
The old DFS field no longer controls the data frame size. To detect this
layout, we try writing 0xF to DFS. If we read back 0x0, then this device
has SSI_MAX_XFER_SIZE=32.
dwc-ssi is the version of the device on Intel Keem Bay SoCs and Canaan
Kendryte K210 SoCs. The layout of ctrlr0 is:
The semantics of the fields have not changed since the previous version.
However, SSI_MAX_XFER_SIZE is effectively always 32.
To support these different layouts, we model our approach on the one
which the Linux kernel has taken. During probe, the driver calls an init
function stored in driver_data. This init function is responsible for
determining the layout of CTRLR0, and supplying the update_cr0 function.
The style of and information behind this commit is based on the Linux MMIO
driver for these devices. Specific reference was made to the series adding
support for Intel Keem Bay SoCs [1].
Sean Anderson [Fri, 16 Oct 2020 22:57:50 +0000 (18:57 -0400)]
spi: dw: Add SoC-specific compatible strings
This adds SoC-specific compatible strings to all users of the designware
spi device. This will allow for the correct driver to be selected for each
device. Where it is publicly documented, a compatible string for the
specific device version has also been added. Devices without
publicly-documented device versions include MSCC SoCs, and Arc Socs. All
compatible strings except those for SoCFPGAs and some of the versioned
strings have been taken from Linux.
Since SSI_MAX_XFER_SIZE is determined at runtime, this is not strictly
necessary. However, it is a good cleanup and brings things closer to Linux.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Tested-by Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com> Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Sean Anderson [Fri, 16 Oct 2020 22:57:49 +0000 (18:57 -0400)]
spi: dw: Rearrange struct dw_spi_priv
This should reduce the size of the struct, and also groups more similar
fields together.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Tested-by Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com> Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Sean Anderson [Fri, 16 Oct 2020 22:57:46 +0000 (18:57 -0400)]
spi: dw: Use generic function to read reg address
Using an fdt-specific function causes problems when compiled with a live
tree.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Tested-by Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com> Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Sean Anderson [Fri, 16 Oct 2020 22:57:45 +0000 (18:57 -0400)]
spi: dw: Rename "cs-gpio" to "cs-gpios"
This property is named differently than other SPI drivers with the same
property, as well as the property as used in Linux.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Tested-by Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com> Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Sean Anderson [Fri, 16 Oct 2020 22:57:44 +0000 (18:57 -0400)]
spi: dw: Convert calls to debug to dev_*
This allows different log levels to be enabled or disabled depending on the
desired level of verbosity. In particular, it allows for general debug
information to be printed while excluding more verbose logging which may
interfere with timing.
Signed-off-by: Sean Anderson <seanga2@gmail.com> Reviewed-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Sean Anderson [Fri, 16 Oct 2020 22:57:43 +0000 (18:57 -0400)]
spi: dw: Fix driving MOSI low while recieving
The resting state of MOSI is high when nothing is driving it. If we drive
it low while recieving, it looks like we are transmitting 0x00 instead of
transmitting nothing. This can confuse slaves (like SD cards) which allow
new commands to be sent over MOSI while they are returning data over MISO.
The return of MOSI from 0 to 1 at the end of recieving a byte can look like
a start bit and a transmission bit to an SD card. This will cause the card
to become out-of-sync with the SPI device, as it thinks the device has
already started transmitting two bytes of a new command. The mmc-spi driver
will not detect the R1 response from the SD card, since it is sent too
early, and offset by two bits. This patch fixes transfer errors when using
SD cards with dw spi.
Signed-off-by: Sean Anderson <seanga2@gmail.com> Reviewed-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
U-Boot is able to erase bad mtd blocks on raw nand devices, but this
is not true for spinand flashes. Lets enable this feature for spinand
flashes as well. This is extemelly useful for flash testing.
Frieder Schrempf [Mon, 22 Jun 2020 13:16:33 +0000 (16:16 +0300)]
mtd: spinand: Do not erase the block before writing a bad block marker
Currently when marking a block, we use spinand_erase_op() to erase
the block before writing the marker to the OOB area. Doing so without
waiting for the operation to finish can lead to the marking failing
silently and no bad block marker being written to the flash.
In fact we don't need to do an erase at all before writing the BBM.
The ECC is disabled for raw accesses to the OOB data and we don't
need to work around any issues with chips reporting ECC errors as it
is known to be the case for raw NAND.
Fixes: 7529df465248 ("mtd: nand: Add core infrastructure to support SPI NANDs") Cc: stable@vger.kernel.org Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de> Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/linux-mtd/20200218100432.32433-4-frieder.schrempf@kontron.de
Frieder Schrempf [Mon, 22 Jun 2020 13:16:32 +0000 (16:16 +0300)]
mtd: spinand: Explicitly use MTD_OPS_RAW to write the bad block marker to OOB
When writing the bad block marker to the OOB area the access mode
should be set to MTD_OPS_RAW as it is done for reading the marker.
Currently this only works because req.mode is initialized to
MTD_OPS_PLACE_OOB (0) and spinand_write_to_cache_op() checks for
req.mode != MTD_OPS_AUTO_OOB.
Fix this by explicitly setting req.mode to MTD_OPS_RAW.
Fixes: 7529df465248 ("mtd: nand: Add core infrastructure to support SPI NANDs") Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de> Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/linux-mtd/20200218100432.32433-3-frieder.schrempf@kontron.de
Frieder Schrempf [Mon, 22 Jun 2020 13:16:31 +0000 (16:16 +0300)]
mtd: spinand: Stop using spinand->oobbuf for buffering bad block markers
For reading and writing the bad block markers, spinand->oobbuf is
currently used as a buffer for the marker bytes. During the
underlying read and write operations to actually get/set the content
of the OOB area, the content of spinand->oobbuf is reused and changed
by accessing it through spinand->oobbuf and/or spinand->databuf.
This is a flaw in the original design of the SPI NAND core and at the
latest from 13c15e07eedf ("mtd: spinand: Handle the case where
PROGRAM LOAD does not reset the cache") on, it results in not having
the bad block marker written at all, as the spinand->oobbuf is
cleared to 0xff after setting the marker bytes to zero.
To fix it, we now just store the two bytes for the marker on the
stack and let the read/write operations copy it from/to the page
buffer later.
Fixes: 7529df465248 ("mtd: nand: Add core infrastructure to support SPI NANDs") Cc: stable@vger.kernel.org Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de> Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/linux-mtd/20200218100432.32433-2-frieder.schrempf@kontron.de
Patrick Delaunay [Thu, 15 Oct 2020 15:18:17 +0000 (17:18 +0200)]
spi: migrate trace to dev and log macro in spi uclass
Define LOG_CATEGORY and change printf and pr_*
to dev_ (when dev is available) or log_ macro.
This patch adds the support of logging feature with log command
(filtering, display of device name in trace) and allows to
suppress traces via the syslog driver.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Jagan Teki [Fri, 23 Oct 2020 08:32:48 +0000 (14:02 +0530)]
dh_imx6: Switch to full DM-aware
Enable DM_SPI/DM_SPI_FLASH with a related config option.
Build fine, but not tested.
Cc: Ludwig Zenz <lzenz@dh-electronics.de> Cc: Andreas Geisreiter <ageisreiter@dh-electronics.de> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Hayes Wang [Wed, 16 Dec 2020 09:03:23 +0000 (17:03 +0800)]
eth/r8152: fix the aggregation issue
Remove the redundant setting for USB_RX_EARLY_SIZE. Besides, for
RTL8153B, it is necessary to notify the hardware of the changes
of the aggregation settings.
Ran Wang [Wed, 18 Nov 2020 07:49:02 +0000 (15:49 +0800)]
usb: xhci: fix lack of short packet event trb handling
For bulk IN transfer, the codes will set ISP flag to request event TRB
being generated by xHC for the case of short packet. So when encountering
buffer-cross-64K-boundary (which we will divide payload and enqueuqe
more than 1 transfer TRB), and the first TRB ends up with a short packet
condition it will trigger an short packet code transfer event per that
flag and cause more than 1 event TRB generated for this transfer.
However, current codes will only handle the first transfer event TRB
then mark current transfer completed, causing next transfer
failure due to event TRB mis-match.
Such issue has been observed on some Layerscape platforms (LS1028A,
LS1088A, etc) with USB ethernet device.
This patch adds a loop to make sure the event TRB for last transfer TRB
has been handled in time.
Signed-off-by: Ran Wang <ran.wang_1@nxp.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
projects / u-boot.git / log