Dylan Hung [Thu, 9 Dec 2021 02:12:28 +0000 (10:12 +0800)]
clk: ast2600: Revise MII interface delay
The clock delay of the RMII/RGMII interface is controlled by SCU340~35C.
These values are obtained by measurement and experiments so we simply
use macro to define them.
Signed-off-by: Dylan Hung <dylan_hung@aspeedtech.com> Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Dylan Hung [Thu, 9 Dec 2021 02:12:26 +0000 (10:12 +0800)]
ARM: dts: ast2600: Add MDIO devices
There are 4 MDIO bus controllers in AST2600 SOC. Each of them can
connect to one or more PHY chips and is flexible to work with the 4 MAC
devices in AST2600. On AST2600 EVB, MDIO 0,1,2,3 connect to the PHY
chips used by MAC 0,1,2,3 respectively.
Signed-off-by: Dylan Hung <dylan_hung@aspeedtech.com> Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Dylan Hung [Thu, 9 Dec 2021 02:12:24 +0000 (10:12 +0800)]
net: ftgmac100: Add DM_MDIO support
Add support for DM_MDIO to connect to PHY. For the systems that have a
stand-alone MDIO hardware block, enable CONFIG_DM_MDIO to use driver
model for MDIO devices.
Signed-off-by: Dylan Hung <dylan_hung@aspeedtech.com> Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
This commit introduces get/set_rate callbacks, these are dummy at
the moment, and can be used to get/set clock for various devices
based on the clk id.
Signed-off-by: Amit Singh Tomar <amittomer25@gmail.com> Reviewed-by: Sean Anderson <seanga2@gmail.com>
AJ Bagwell [Fri, 3 Dec 2021 15:18:53 +0000 (15:18 +0000)]
pinctrl: single: add support for pinctrl-single, pins when #pinctrl-cells = 2
Changes to the am33xx device (33e9021a) trees have been merged in from
the upstream linux kernel which now means the device tree uses the new
pins format (as of 5.10) where the confinguration can be stores as a
separate configuration value and pin mux mode which are then OR'd
together.
This patch adds support for the new format to u-boot so that
pinctrl-cells is now respected when reading in pinctrl-single,pins Signed-off-by: Anthony Bagwell <anthony.bagwell@hivehome.com>
Qu Wenruo [Mon, 27 Dec 2021 06:11:14 +0000 (14:11 +0800)]
fs/btrfs: fix a bug that U-boot fs btrfs implementation doesn't handle NO_HOLE feature correctly
[BUG]
When passing a btrfs with NO_HOLE feature to U-boot, and if one file
contains holes, then the hash of the file is not correct in U-boot:
# mkfs.btrfs -f test.img # Since v5.15, mkfs defaults to NO_HOLES
# mount test.img /mnt/btrfs
# xfs_io -f -c "pwrite 0 4k" -c "pwrite 8k 4k" /mnt/btrfs/file
# md5sum /mnt/btrfs/file 277f3840b275c74d01e979ea9d75ac19 /mnt/btrfs/file
# umount /mnt/btrfs
# ./u-boot
=> host bind 0 /home/adam/test.img
=> ls host 0
< > 12288 Mon Dec 27 05:35:23 2021 file
=> load host 0 0x1000000 file
12288 bytes read in 0 ms
=> md5sum 0x1000000 0x3000
md5 for 01000000 ... 01002fff ==> 855ffdbe4d0ccc5acab92e1b5330e4c1
The md5sum doesn't match at all.
[CAUSE]
In U-boot btrfs implementation, the function btrfs_read_file() has the
following iteration for file extent iteration:
/* Read the aligned part */
while (cur < aligned_end) {
ret = lookup_data_extent(root, &path, ino, cur, &next_offset);
if (ret < 0)
goto out;
if (ret > 0) {
/* No next, direct exit */
if (!next_offset) {
ret = 0;
goto out;
}
}
/* Read file extent */
But for NO_HOLES features, hole extents will not have any extent item
for it.
Thus if @cur is at a hole, lookup_data_extent() will just return >0, and
update @next_offset.
But we still believe there is some data to read for @cur for ret > 0
case, causing we read extent data from the next file extent.
This means, what we do for above NO_HOLES btrfs is:
- Read 4K data from disk to file offset [0, 4K)
So far the data is still correct
- Read 4K data from disk to file offset [4K, 8K)
We didn't skip the 4K hole, but read the data at file offset [8K, 12K)
into file offset [4K, 8K).
This causes the checksum mismatch.
[FIX]
Add extra check to skip to the next non-hole range after
lookup_data_extent().
Ovidiu Panait [Sat, 1 Jan 2022 17:13:30 +0000 (19:13 +0200)]
common: board_r: include asm-generic/gpio.h
Not all architectures define <asm/gpio.h> and even on those that do, the
header cannot be included for all boards without causing various build
failures.
Since common/board_r.c only needs gpio_hog_probe_all() declaration, include
<asm-generic/gpio.h> and drop the associated ifdef.
Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Ovidiu Panait [Sat, 1 Jan 2022 17:13:29 +0000 (19:13 +0200)]
common: board_r: move init_addr_map() to init.h
asm/mmu.h include is currently guarded by CONFIG_ADDR_MAP ifdef because
the header is only present on arm and powerpc. In order to remove the
dependency on this header and the associated ifdef, move init_addr_map()
declaration to init.h, since it is only called during the common init
sequence.
Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Ovidiu Panait [Sat, 1 Jan 2022 17:13:27 +0000 (19:13 +0200)]
common: board_r: drop initr_kgdb wrapper
Add a return value to kgdb_init and use it directly in the post-relocation
init sequence, rather than using a wrapper stub. Also, move the "KGDB"
print message inside kgdb_init().
Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Ovidiu Panait [Sat, 1 Jan 2022 17:13:26 +0000 (19:13 +0200)]
common: remove bedbug debugger support
Commit 98f705c9cefd ("powerpc: remove 4xx support") removed (in 2017) the
last code that made use of bedbug debugger support. Since there aren't
any boards left that define either CONFIG_CMD_BEDBUG or a real
bedbug_init(), drop this feature from u-boot.
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com> Reviewed-by: Thomas Huth <thuth@redhat.com> Reviewed-by: Simon Glass <sjg@chromium.org>
qianfan Zhao [Tue, 16 Nov 2021 00:30:12 +0000 (08:30 +0800)]
drivers: musb_gadget: Save endpoint desc to usb_ep->desc
Fix fastboot flash bug.
If the downloading file size is equal to the partition size, "fastboot
flash" can't work, at least in sunxi platform, because used an
uninitalized point: ep->desc.
This patch also fixed 'data abort' bug in am335x platform.
Robert Marko [Wed, 5 Jan 2022 15:01:00 +0000 (16:01 +0100)]
mtd: nand: pxa3xx: set mtd->dev
Currently the pxa3xx driver does not set the udevice in the mtd_info
struct and this prevents the mtd from parsing the partitions via DTS
like for SPI-NOR.
So simply set the mtd->dev to the driver udevice.
Signed-off-by: Robert Marko <robert.marko@sartura.hr> Reviewed-by: Stefan Roese <sr@denx.de>
Tom Rini [Mon, 17 Jan 2022 16:24:43 +0000 (11:24 -0500)]
Merge branch '2022-01-15-TI-platform-updates'
- Let am335x_evm use the CPSW or PRUSS ethernet.
- Implement timer_get_boot_us in the omap timer driver
- gpmc bitflip, QSPI clock calculation on am437x, da8xx_gpio bugfixes
- Assorted K3 updates
Tom Rini [Mon, 17 Jan 2022 13:36:12 +0000 (08:36 -0500)]
Merge tag 'u-boot-at91-2022.04-b' of https://source.denx.de/u-boot/custodians/u-boot-at91
Second set of u-boot-at91 features for the 2022.04 cycle:
This small feature set includes few changes for sama7g5 and sama7g5ek:
turn blue led on at boot, changes required for the Rev4 of the board,
better sync with the Linux DT with regards to the new DT nodes.
CONFIG_PHANDLE_CHECK_SEQ will allow different sequence number for nodes
that have the same name, but they are different.
In sama7g5ek case, there are multiple 'i2c@600' nodes which are child
nodes of different parent 'flexcom' nodes.
These are different i2c busses even if the node is the same, and have to be
differentiated.
Without this config, the sequence number 0 is reused for two i2c busses, and
this is something that we have to avoid:
Looking for 'i2c' at 4704, name i2c@600
- serial0, /ahb/apb/serial@e1824200
- i2c0, /ahb/apb/flexcom@e181c000/i2c@600
Found seq 0
i2c_post_bind: i2c@600, seq=0
Looking for 'i2c' at 6236, name i2c@600
- serial0, /ahb/apb/serial@e1824200
- i2c0, /ahb/apb/flexcom@e181c000/i2c@600
Found seq 0
i2c_post_bind: i2c@600, seq=0
After this patch:
Looking for 'i2c' at 4704, name i2c@600
- serial0, /ahb/apb/serial@e1824200
- i2c0, /ahb/apb/flexcom@e181c000/i2c@600
- i2c1, /ahb/apb/flexcom@e2818000/i2c@600
Found seq 1
Before the patch:
=> i2c bus
Bus 0: i2c@600
Bus 0: i2c@600 (active 0)
52: eeprom@52, offset len 1, flags 0
53: eeprom@53, offset len 1, flags 0
=>
After the patch:
=> i2c bus
Bus 0: i2c@600
Bus 1: i2c@600 (active 1)
52: eeprom@52, offset len 1, flags 0
53: eeprom@53, offset len 1, flags 0
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Eugen Hristev [Tue, 4 Jan 2022 16:23:36 +0000 (18:23 +0200)]
ARM: dts: at91: sama7g5ek: move eeproms to flexcom8
The rev4 of the board sama7g5ek has the eeproms on flexcom8 instead of
flexcom1.
Initialize flexcom8 with required pincontrol and move the eeproms accordingly.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Eugen Hristev [Tue, 4 Jan 2022 16:21:54 +0000 (18:21 +0200)]
ARM: dts: at91: sama7g5: add flx8 and required nodes
Add Flexcom8 node with required referenced nodes as phandles.
Since Flexcom8 is present in Linux, take the node exactly as-is from Linux.
Some nodes are referenced in Linux as phandles, the dma and the gic.
Add them as well to the file, even if they are unused by Uboot.
This is a step towards having the U-boot DT equivalent with the DT in Linux.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Mark Kettenis [Mon, 10 Jan 2022 19:58:42 +0000 (20:58 +0100)]
arm: dts: apple: Update Apple M1 device trees
This synchronizes the device trees with those that are in the
process of being upstreamed into Linux. This is mostly the
current state of the device trees on the asahilinux branch
with a few extra bits used by OpenBSD. This includes device
trees for machines that were still missing.
There are still some differences that will hopefully be resolved
soon.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org> Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com> Reviewed-by: Simon Glass <sjg@chromium.org>
board: ti: am335x: Choose CPSW or PRUSS configuration based on jumper setting
The am335x-ice-v2 board's Ethernet ports can be configured
in 'MII' or 'RMII' mode to be connected to 'PRUSS' or 'CPSW'
Ethernet subsystems.
This patch sets the environment variable 'ice_mii' to
'mii' or 'rmii' accordingly. Based on that we choose the
appropriate board devicetree i.e. 'am335x-ice-v2.dtb' or
'am335x-ice-v2-prueth.dtb'.
Since there are 2 Ethernet ports with 2 modes, there can be 4
configurations but for now we consider both ports in different modes
to be an invalid configuration and prevent boot in that case.
Signed-off-by: Roger Quadros <rogerq@ti.com>
[Amjad: use overlay instead of using new am335x-ice-v2-prueth.dtb] Signed-off-by: Amjad Ouled-Ameur <aouledameur@baylibre.com> Reviewed-by: Tom Rini <trini@konsulko.com>
[trini: Make prueth_is_mii be marked __maybe_unused] Signed-off-by: Tom Rini <trini@konsulko.com>
David Rivshin [Thu, 18 Nov 2021 18:25:24 +0000 (13:25 -0500)]
nand: gpmc: Handle bitflips in erased pages when using BCH ECC engine
In the case of an erased (sub)page both the data and ECC are all 0xFF
bytes. This fails the normal ECC verification, as the computed ECC of
all-0xFF is not also 0xFF. The GPMC NAND driver attempted to detect
erased pages by checking that the ECC bytes are all-0xFF, but this had
two problems:
1) bitflips in the data were not corrected, so the data looked not-erased
2) bitflips in the ECC bytes were reported as uncorrectable ECC errors
The equivalent Linux driver [1] correctly handles this by counting the
number of 0-bits in the combination of data and ECC bytes. If the number
of 0-bits is less than the amount of bits correctable by the selected
ECC algorithm, then it is treated as an erased page with correctable
bitflips.
Implement similar, though simplified, logic in omap_correct_data_bch().
[1] see omap_elm_correct_data() in omap2.c
Signed-off-by: David Rivshin <drivshin@allworx.com>
Stefan Mätje [Tue, 30 Nov 2021 00:06:56 +0000 (01:06 +0100)]
Fix wrong QSPI clock calculation for AM4372
On AM4372 the SPI_GCLK input gets its clock from the PRCM module which
divides the PER_CLKOUTM2 frequency (192MHz) by a fixed factor of 4.
See AM437x Reference Manual in section 27 QSPI >> 27.2 Integration.
The QSPI_FCLK therefore needs to take this factor into account and
becomes (192000000 / 4).
Signed-off-by: Stefan Mätje <stefan.maetje@esd.eu>
The fastboot protocol uses per default the UDP port 5554. In some cases
it might be needed to change the used port. The fastboot utility provides
a way to specifiy an other port number to use already.
Markus Koch [Tue, 11 Jan 2022 18:22:54 +0000 (19:22 +0100)]
net: fsl: Fix busy flag polling register
NXP's mEMAC reference manual, Chapter 6.5.5 "MDIO Ethernet Management
Interface usage", specifies to poll the BSY (0) bit in the CFG/STAT
register to wait until a transaction has finished, not bit 31 in the
data register.
In the Linux kernel, this has already been fixed in commit 26eee0210ad7
("net/fsl: fix a bug in xgmac_mdio").
This patch changes the register in the fman_mdio and fsl_ls_mdio
drivers.
As the MDIO_DATA_BSY define is no longer in use, this patch also removes
its definition from the fsl_memac header.
Signed-off-by: Markus Koch <markus@notsyncing.net> Reviewed-by: Camelia Groza <camelia.groza@nxp.com>
Marek Vasut [Sat, 1 Jan 2022 19:12:23 +0000 (20:12 +0100)]
net: eth-phy: Demote missing phy-handle log message to debug
Reduce the missing phy-handle log message to debug message. It is
possible for ethernet DT node to have no phy-handle e.g. in case
of a fixed-link connection. Furthermore, drop the FEC: prefix,
which is a copy-paste error and rather print the ethernet device
name.
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Ramon Fried <rfried.dev@gmail.com> Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Vladimir Oltean [Sat, 4 Dec 2021 23:00:35 +0000 (01:00 +0200)]
net: dsa: sja1105: fix device id detection
The sja1105_check_device_id() function contains logic to work without
changing the device tree on reworked boards, one of which I have (the
NXP LS1021A-TSN normally has a SJA1105T, but I have a version with a
resoldered SJA1105Q which is pin compatible). This logic is taken from
the Linux driver.
However this logic gets shortcircuited in U-Boot by an earlier check for
the exact device ID specified in the device tree. So the reworked board
does not probe the SJA1105Q switch. Remove this duplicated logic and let
the automatic device ID detection do its job.
Fixes: f24b666b2204 ("net: dsa: add driver for NXP SJA1105 L2 switch") Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Vladimir Oltean [Sat, 4 Dec 2021 23:00:34 +0000 (01:00 +0200)]
net: dsa: fix phydev->speed being uninitialized for the CPU port fixed PHY
If the DSA API is going to allow drivers to do things such as:
- phy_config in dsa_ops :: port_probe
- phy_startup in dsa_ops :: port_enable
then it would actually be good if the ->port_probe() method would
actually be called in all cases before the ->port_enable() is.
Currently this is true for user ports, but not true for the CPU port,
because the CPU port does not have a udevice registered for it (this is
all part of DSA's design). So the current issue is that after
phy_startup has finished for the CPU port, its phydev->speed is an
uninitialized value, because phy_config() was never called for the
priv->cpu_port_fixed_phy, and it is precisely phy_config() who copies
the speed into the phydev in the case of the fixed PHY driver.
So we need to simulate a probing event for the CPU port by manually
calling the driver's ->port_probe() method for the CPU port.
Fixes: 8a2982574854 ("net: dsa: introduce a .port_probe() method in struct dsa_ops") Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
cmd: pxe_utils: sysboot: add label override support
This will allow consumers to choose a pxe label at runtime instead of
having to prompt the user. One good use-case for this, is choosing
whether or not to apply a dtbo depending on the hardware configuration.
e.g: for TI's AM335x EVM, it would be convenient to apply a particular
dtbo only when the J9 jumper is on PRUSS mode. To achieve this, the
pxe menu should have 2 labels, one with the dtbo and the other without,
then the "pxe_label_override" env variable should point to the label with
the dtbo at runtime only when the jumper is on PRUSS mode.
This change can be used for different use-cases and bring more
flexibilty to consumers who use sysboot/pxe_utils.
if "pxe_label_override" is set but does not exist in the pxe menu,
the code should fallback to the default label if given, and no failure
is returned but rather a warning message.
Signed-off-by: Amjad Ouled-Ameur <aouledameur@baylibre.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Artem Lapkin <email2tema@gmail.com> Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Call dram_init_banksize() from spl_board_init() otherwise TFTP download
fails due to lmb_get_free_size() not able to find unreserved region due
to lack of DRAM size info. Required to support Ethernet boot on AM64x.
net: ti: am65-cpsw: Add support for multi port independent MAC mode
On certain TI SoC, like AM64x there is a CPSW3G which supports 2
external independent MAC ports for single CPSW instance.
It is not possible for Ethernet driver to register more than one port
for given instance.
This patch modifies top level CPSW NUSS as UCLASS_MISC and binds
UCLASS_ETH to individual ports so as to support bring up more than one
Ethernet interface in U-Boot.
Note that there is no isolation in the since, CPSW NUSS is in promisc
mode and forwards all packets to host.
Since top level driver is now UCLASS_MISC, board files would need to
instantiate this driver explicitly.
Probe toplevel AM65 CPSW NUSS driver from misc_init_r() when driver
is enabled. Since driver is modeled as UCLASS_MISC, we need to
explicitly probe the driver. Use common misc_init_r() that entire
K3 family of SoCs.
dma: ti: k3-udma: Fix rflow reservation for PKTDMA
Driver has a bug in that it uses rflow_in_use bitmap when setting up free rflow range
from TISCI but use rflow_map for reservation in __udma_reserve_rflow()
Fix this by dropping rflow_in_use bitmap array and use rflow_map for
PKTDMA. BCDMA does not need rflow_in_use either.
This fixes CPSW3g not able to get DMA channels at R5 SPL on AM64x
ARM: mach-k3: sysfw-loader: Copy sysfw.itb to OCRAM in OSPI/SPI bootmode
In case of xSPI bootmode OSPI flash is in DDR mode and needs to be accessed
in multiple of 16bit accesses Hence we cannot parse sysfw.itb FIT image
directly on OSPI flash via MMIO window. So, copy the image to internal
on-chip RAM before parsing the image.
Moreover, board cfg data maybe modified by ROM/TIFS in case of HS platform
and thus cannot reside in OSPI/xSPI and needs to be copied over to
internal OCRAM.
Michael Liebert [Wed, 15 Dec 2021 15:14:28 +0000 (16:14 +0100)]
arm: mach-k3: am642_init: Unlock MCU PADCFG regs
Currently only the PADCFG registers of the main domain are unlocked.
Also unlock PADCFG registers of MCU domain, so MCU pin muxing can be configured by u-boot or Linux.
Signed-off-by: Michael Liebert <liebert@ibv-augsburg.de> Tested-by: Christian Gmeiner <christian.gmeiner@gmail.com> Acked-by: Nishanth Menon <nm@ti.com>
Tom Rini [Sat, 15 Jan 2022 12:39:09 +0000 (07:39 -0500)]
Merge tag 'efi-2022-04-rc1' of https://source.denx.de/u-boot/custodians/u-boot-efi
Pull request for efi-2022-04-rc1
Documentation:
* Fix building HTML documentation of readthedocs.io
* Add ARM Juno board documentation
* Build requirements for Alpine Linux
* Include DM headers in API documentation
UEFI:
* Fix section alignment of EFI binaries
* Fix header length of RISC-V EFI binaries allowing to run them on EDK II
* Remove kaslr-seed from device tree if the EFI_RNG_PROTOCOL is provided
Tom Rini [Sat, 15 Jan 2022 12:34:46 +0000 (07:34 -0500)]
Merge branch '2022-01-14-assorted-fixes'
- A number of fixes in various subsystems. This includes having the phy
uclass track power-on and init counts as this should resolve some
tricky functional problems on a number of platforms.
Simon Glass [Tue, 4 Jan 2022 10:51:13 +0000 (03:51 -0700)]
x86: efi: Tweak the code used for the 64-bit EFI app
Add an empty CPU init function to avoid fiddling with low-level CPU
features in the app. Set up the C runtime correctly for 64-bit use
and avoid clearing BSS, since this is done by EFI when U-Boot is loaded.
Simon Glass [Tue, 4 Jan 2022 10:51:11 +0000 (03:51 -0700)]
x86: efi: Update efi_get_next_mem_desc() to avoid needing a map
At present this function requires a pointer to struct efi_entry_memmap
but the only field used in there is the desc_size. We want to be able
to use it from the app, so update it to use desc_size directly.
Simon Glass [Tue, 4 Jan 2022 10:51:10 +0000 (03:51 -0700)]
efi: Move exit_boot_services into a function
At present this code is inline in the app and stub. But they do the same
thing. The difference is that the stub does it immediately and the app
doesn't want to do it until the end (when it boots a kernel) or not at
all, if returning to UEFI.
Move it into a function so it can be called as needed.
Add a comment showing how to store the memory map so that it can be
accessed within the app if needed, for debugging purposes only. The map
can change without notice.
efidebug: avoid 'dfu_alt_info not defined' message
If variable dfu_alt_info is not defined duplicate messages are displayed.
=> efidebug boot dump
Scanning disk mmc2.blk...
Scanning disk mmc1.blk...
Scanning disk mmc0.blk...
Found 3 disks
No EFI system partition
"dfu_alt_info" env variable not defined!
Probably dfu_alt_info not defined
"dfu_alt_info" env variable not defined!
Probably dfu_alt_info not defined
Remove the 'Probably dfu_alt_info not defined' message.
Instead write a warning if the variable contains no entities.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
efi_loader: Get rid of kaslr-seed if EFI_RNG_PROTOCOL is installed
U-Boot, in some occasions, injects a 'kaslr-seed' property on the /chosen
node. That would be problematic in case we want to measure the DTB we
install in the configuration table, since it would change across reboots.
The Linux kernel EFI-stub completely ignores it and only relies on
EFI_RNG_PROTOCOL for it's own randomness needs (i.e the randomization
of the physical placement of the kernel). In fact it (blindly) overwrites
the existing seed if the protocol is installed. However it still uses it
for randomizing it's virtual placement.
So let's get rid of it in the presence of the RNG protocol.
It's worth noting that TPMs also provide an RNG. So if we tweak our
EFI_RNG_PROTOCOL slightly and install the protocol when a TPM device
is present the 'kaslr-seed' property will always be removed, allowing
us to reliably measure our DTB.
The alignment of sections in the EFI binaries generated by U-Boot is
incorrect.
According to the PE-COFF specification [1] the minimum value for
FileAlignment is 512. If the value of SectionAlignment is
less then the page size, it must equal FileAlignment.
Let's set both values to 512 for the ARM and RISC-V architectures.
EDK II refuses to load the EFI binaries created by U-Boot.
The reason is an incorrect PE-COFF header. The number of
data directories does not match NumberOfRvaAndSizes.
This leads to a failed consistency check in
PeCoffLoaderGetPeHeader():
Patrick Delaunay [Wed, 12 Jan 2022 09:55:41 +0000 (10:55 +0100)]
doc: add include/dm/fdtaddr.h to the HTML documentation
Correct Sphinx style comments in include/dm/fdtaddr.h
and add the devfdt API to the HTML documentation;
these functions are NOT compatible with live tree.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com> Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Patrick Delaunay [Wed, 12 Jan 2022 09:53:49 +0000 (10:53 +0100)]
doc: add include/dm/of*.h to the HTML documentation
Correct Sphinx style comments in include/dm/ofnode.h
and add the device tree node API to the HTML documentation;
the ofnode functions are compatible with Live tree or with flat
device tree.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com> Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Andre Przywara [Mon, 20 Dec 2021 18:12:04 +0000 (18:12 +0000)]
doc: add Arm Juno board documentation
The Juno Arm development board is an open, vendor-neutral, Armv8-A
development platform.
Add documentation that briefly outlines the hardware, and describes
building and installation of U-Boot.
Signed-off-by: Andre Przywara <andre.przywara@arm.com> Reviewed-by: Sudeep Holla <sudeep.holla@arm.com> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Reviewed-by: Simon Glass <sjg@chromium.org>
Eugen Hristev [Tue, 4 Jan 2022 16:20:19 +0000 (18:20 +0200)]
lib: Kconfig: fix PHANDLE_CHECK_SEQ position outside of menu
CONFIG_PHANDLE_CHECK_SEQ is outside of the menu 'Library routines'
thus it's invisible in menuconfig and cannot be selected.
Fix this by moving the 'endmenu' after the PHANDLE_CHECK_SEQ definition
Fixes: c589132a1d ("fdt: Use phandle to distinguish DT nodes with same name") Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com> Reviewed-by: Aswath Govindraju <a-govindraju@ti.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Peter Robinson [Sun, 2 Jan 2022 11:38:35 +0000 (11:38 +0000)]
env: fat: Add new lines at the end of print statements
Add some new line feeds at the end of print messages to make things
easier to read on the console. The other env options do this so
this is just an omission for FAT env.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
On boards using the RK3399 SoC, the USB OHCI and EHCI controllers share
the same PHY device instance. While these controllers are being stopped
they both attempt to power-off and deinitialize it, but trying to
power-off the deinitialized PHY device results in a hang. This usually
happens just before booting an OS, and can be explicitly triggered by
running "usb start; usb stop" in the U-Boot shell.
Implement a uclass-wide counting mechanism for PHY initialization and
power state change requests, so that we don't power-off/deinitialize a
PHY instance until all of its users want it done. The Allwinner A10 USB
PHY driver does this counting in-driver, remove those parts in favour of
this in-uclass implementation.
The sandbox PHY operations test needs some changes since the uclass will
no longer call into the drivers for actions matching its tracked state
(e.g. powering-off a powered-off PHY). Update that test, and add a new
one which simulates multiple users of a single PHY.
The major complication here is that PHY handles aren't deduplicated per
instance, so the obvious idea of putting the counts in the PHY handles
don't immediately work. It seems possible to bind a child udevice per
PHY instance to the PHY provider and deduplicate the handles in each
child's uclass-private areas, like in the CLK framework. An alternative
approach could be to use those bound child udevices themselves as the
PHY handles. Instead, to avoid the architectural changes those would
require, this patch solves things by dynamically allocating a list of
structs (one per instance) in the provider's uclass-private area.
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org> Tested-by: Peter Robinson <pbrobinson@gmail.com> - Rock960
Mark Kettenis [Tue, 21 Dec 2021 16:31:50 +0000 (17:31 +0100)]
armv8: apple: Disable PSCI reset
Apple's ARMv8 cores don't implement EL3 and therefore don't
provide a PSCI implementation. So don't attempt to use
PSCI to reset on machines using Apple SoCs.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
This happens when nvme_print_info() tries to return to the caller. It
looks like this error is caused by trying to allocate 8 KiB of memory
on the stack by the two uses of ALLOC_CACHE_ALIGN_BUFFER().
Use malloc_cache_aligned() to allocate this memory dynamically instead.
This fixes 'nvme detail' on Turris Omnia.
Note that similar change was applied to file drivers/nvme/nvme.c in past by
commit 2f83481dff9c ("nvme: use page-aligned buffer for identify command").
Signed-off-by: Pali Rohár <pali@kernel.org> Signed-off-by: Marek Behún <marek.behun@nic.cz>
projects / u-boot.git / log