Adam Ford [Mon, 2 Sep 2019 11:52:01 +0000 (06:52 -0500)]
ARM: omapl138_lcdk: Remove dead code
The header it littered with #ifdefs and #defines and that appear
to be legacy associations to the older da850-evm and in some cases
obsolete with either Kconfig or DM migrations. This patch removes
these legacy references.
Enable driver model for USB, MMC, SPI and SPI_FLASH. Also enable BLK.
This will remove the following compile warnings:
===================== WARNING ======================
This board does not use CONFIG_DM_MMC. Please update
the board to use CONFIG_DM_MMC before the v2019.04 release.
====================================================
===================== WARNING ======================
This board does not use CONFIG_DM_USB. Please update
the board to use CONFIG_DM_USB before the v2019.07 release.
====================================================
===================== WARNING ======================
This board does not use CONFIG_DM_SPI_FLASH. Please update
the board to use CONFIG_SPI_FLASH before the v2019.07 release.
====================================================
Target was compile tested, build was clean.
Add device tree from Linux for driver model conversion
and enable OF_CONTROL. This will remove the following compile
warning:
==================================================
Device Tree Source is not correctly specified.
Please define 'CONFIG_DEFAULT_DEVICE_TREE'
or build with 'DEVICE_TREE=<device_tree>' argument
===================================================
Target was compile tested, build was clean.
In case dma_ring_reset_quirk is not set the k3_ringacc_ring_reset_dma will
just exit without ring reset. Fix it, by adding ring reset call in case
dma_ring_reset_quirk is not.
Tom Rini [Thu, 12 Sep 2019 03:08:34 +0000 (23:08 -0400)]
Merge tag 'u-boot-rockchip-20190912' of https://gitlab.denx.de/u-boot/custodians/u-boot-rockchip
- add idbloader.img target for rockchip tpl+spl;
- usb ehci/ohci: go on process if clock driver don't have clk_enable();
- remove clk_enable() for rockchip clock drivers;
- add boot order for rockpro64
Kever Yang [Wed, 28 Aug 2019 08:23:47 +0000 (16:23 +0800)]
usb: ohci-generic: don't probe fail if there is no clk_enable() ops
Some clock driver do not have a clk_enable() call back, and we should not
treat this as fail in ehci probe like other modules, eg. clk_enabl_bulk()
do not return fail if ret value is '-ENOSYS'
Signed-off-by: Kever Yang <kever.yang@rock-chips.com> Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Kever Yang [Wed, 28 Aug 2019 08:23:46 +0000 (16:23 +0800)]
usb: ehci-generic: don't probe fail if there is no clk_enable() ops
Some clock driver do not have a clk_enable() call back, and we should not
treat this as fail in ehci probe like other modules, eg. clk_enabl_bulk()
do not return fail if ret value is '-ENOSYS'
Signed-off-by: Kever Yang <kever.yang@rock-chips.com> Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
- Tangier ACPI table fixes
- Support getting high memory size on QEMU x86
- Show UEFI images involved in crash for x86
- EFI loader conventional memory map fix
Tom Rini [Tue, 10 Sep 2019 12:51:17 +0000 (08:51 -0400)]
Merge tag 'u-boot-amlogic-20190910' of https://gitlab.denx.de/u-boot/custodians/u-boot-amlogic
- Add support for dis_u2_susphy_quirk in the xhci-dwc3 driver to fix boot when
a device is plugged only in the OTG capable port for libretech-ac and libretech-cc
Andy Shevchenko [Thu, 29 Aug 2019 14:04:20 +0000 (17:04 +0300)]
x86: tangier: Fix off-by-one error when preparing CSRT
Intel iDMA 32-bit controller has 17 bits for the maximum block size value.
Due to nature of the binary number representation the maximum value is
2^17 - 1. The original code misses the latter part in equation.
Fixes: 5e99fde34a77 ("x86: tangier: Populate CSRT for shared DMA controller") Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Andy Shevchenko [Thu, 29 Aug 2019 14:04:19 +0000 (17:04 +0300)]
x86: tangier: Reserve PCI ECAM in motherboard resources
Per PCI firmware specification the ACPI has to reserve the memory
which is defined as PCI ECAM.
Fixes: 39665beed6f7 ("x86: tangier: Enable ACPI support for Intel Tangier") Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Andy Shevchenko [Thu, 29 Aug 2019 14:04:18 +0000 (17:04 +0300)]
x86: acpi: Annotate struct acpi_table_header with __packed
GCC 9.2 starts complaining about possible pointer misalignment of
pointers to the unpacked (alignment=4) structures in the packed
(alignment=1) ones:
CC arch/x86/cpu/tangier/acpi.o
arch/x86/cpu/tangier/acpi.c: In function ‘acpi_create_fadt’:
arch/x86/cpu/tangier/acpi.c:22:37: warning: taking address of packed
member of ‘struct acpi_fadt’ may result in an unaligned pointer value
[-Waddress-of-packed-member]
22 | struct acpi_table_header *header = &(fadt->header);
CC arch/x86/lib/acpi_table.o
arch/x86/lib/acpi_table.c: In function ‘acpi_create_spcr’:
arch/x86/lib/acpi_table.c:366:37: warning: taking address of packed
member of ‘struct acpi_spcr’ may result in an unaligned pointer value
[-Waddress-of-packed-member]
366 | struct acpi_table_header *header = &(spcr->header);
Fix the potential issues by annotating embedded structures with
__packed even though they are packed naturally.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
[bmeng: add GCC version number in the commit message] Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Neil Armstrong [Mon, 9 Sep 2019 18:52:39 +0000 (18:52 +0000)]
usb: xhci-dwc3: Add support for dis_u2_susphy_quirk
This quirk is necessary for the Amlogic GXL SoCs otherwise the
Port 2 PHY doesn't get out of suspend and U-Boot resets the board after:
XHCI timeout on event type 33... cannot recover.
BUG: failure at drivers/usb/host/xhci-ring.c:474/xhci_wait_for_event()!
BUG!
This quirk is also handled in the dwc3 core code, but until the
xhci-dwc3 driver uses the dwc3 core, the quirk must be handled here
to fix USB support on the Amlogic libretech-cc and libretech-ac board
when a device is only plugged in the OTG port.
Cc: Yuri Frolov <crashing.kernel@gmail.com> Cc: Bin Meng <bmeng.cn@gmail.com> Fixes: dc9cdf859e ("usb: dwc3: Add DWC3 controller driver support") Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Park, Aiden [Tue, 3 Sep 2019 17:43:46 +0000 (17:43 +0000)]
x86: efi_loader: Use efi_add_conventional_memory_map()
Use efi_add_conventional_memory_map() to configure EFI conventional memory
properly with ram_top value. This will give 32-bit mode U-Boot proper
conventional memory regions even if e820 has an entry which is greater than
32-bit address space.
Signed-off-by: Aiden Park <aiden.park@intel.com> Tested-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
[bmeng: fixed some typos in the commit message] Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Bin Meng [Thu, 29 Aug 2019 09:53:03 +0000 (02:53 -0700)]
x86: Drop weak version board_get_usable_ram_top()
Every x86 platform provides board_get_usable_ram_top(), hence there
is no need to provide a weak version board_get_usable_ram_top(), not
to mention there is another weak version board_get_usable_ram_top()
in common/board_f.c.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Reviewed-by: Aiden Park <aiden.park@intel.com>
Andy Shevchenko [Mon, 26 Aug 2019 01:48:15 +0000 (09:48 +0800)]
x86: acpi: Slightly reduce binary size of ACPI tables for Tangier
Using ACPI predefined macros, such as Zero or One, will reduce a binary
size of resulting ACPI tables.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
[bmeng: manually fixed the conflicts when applying] Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Tom Rini [Mon, 9 Sep 2019 14:55:45 +0000 (10:55 -0400)]
arm: ti: Add missing "=" from previous fix
While the original patch to fix a regression in distro boot for mmc on
these platforms had the correct syntax, I broke the change while
applying. Add back in the missing "=" here so that the syntax is
correct.
Reported-by: Andre Heider <a.heider@gmail.com> Fixes: 27e0f3bcf075 ("arm: ti: Fix regression in distro boot for mmc") Signed-off-by: Tom Rini <trini@konsulko.com>
efi_loader: volume name in EFI_FILE_PROTOCOL.GetInfo()
We cannot determine the volume name in U-Boot. Instead of providing a dummy
volume name in case of EFI_FILE_SYSTEM_INFO and EFI_UNSUPPORTED in case of
EFI_FILE_SYSTEM_VOLUME_LABEL consistently return an empty string.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
EFI_FILE_PROTOCOL.Read() is used both to read files and directories.
When reaching the end of a directory we always have to return buffer size
zero irrespective of the incoming buffer size. (The described scenario for
a Shim quirk cannot arise because every directory has at least '.' and '..'
as entries.)
Even when the buffer_size is too small multiple times we have to keep a
reference to our last read directory entry.
When we return to the start of the directory via SetPosition() we must
remove the reference to a previously kept directory entry.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Tom Rini [Fri, 6 Sep 2019 23:49:51 +0000 (19:49 -0400)]
Merge tag 'rpi-next-2019.10' of https://github.com/mbgg/u-boot
- fix mailbox status register used for polling
- fix bcm2835_sdhost to wait long enough for a transfer to complete
- increase kernel image size from 8 MB to 64 MB on arm64
- add support for RPi4
- add prefixes for raspberry pi related stuff to git-mailrc
Andrei Gherzan [Wed, 24 Jul 2019 14:39:06 +0000 (15:39 +0100)]
ARM: bcm283x: Define configs for RaspberryPi 4
Define two target configs for Raspberry Pi 4 (32 and 64bit) and the
corresponding BCM2838* configs.
Be aware of the current limitation in firmware which requires an
explicit configuration to force the arm in 64bit mode when the
respective target is used.
Devices of bcm283x have different base address, depending if they are on
bcm2835 or bcm2836/7. Use BCM283x_BASE depending on the SoC you want to
build and only add the offset in the header files.
Signed-off-by: Matthias Brugger <mbrugger@suse.com> Signed-off-by: Andrei Gherzan <andrei@balena.io>
Andrei Gherzan [Wed, 24 Jul 2019 14:39:04 +0000 (15:39 +0100)]
RPI: Add defconfigs for rpi4 (32/64)
This defines a minimum defconfig for each of the two Raspberry Pi 4
variants. One notable difference is that we don't have a embedded dt for
this board given that the fw supplies us with one which we can reuse.
Furthermore, the ram size is not queryable through mbox interface as the
maximum reported size is 1G. The fw patches the dt with the right
memory configuration and uboot uses it as it is. We avoid u-boot
touching this configuration by making sure CONFIG_ARCH_FIXUP_FDT_MEMORY
is deactivated.
Signed-off-by: Andrei Gherzan <andrei@balena.io> Signed-off-by: Matthias Brugger <mbrugger@suse.com>
Raul Benet [Thu, 13 Jun 2019 13:59:57 +0000 (14:59 +0100)]
mmc: bcm2835-host: Fix wait_transfer_complete
Function bcm_2835_wait_transfer_complete() is not waiting long enough.
The previous code was claiming to wait for ~1 seconds, but as it depends
on register reads it's time actually varies.
Some cards require wait times of up to ~56 ms to perform
the command 'saveenv' on an EXT4 partition.
Re-implement the loop exit condition to use get_timer() which allows
to specify the wait time in more reliable manner. Set the maximum wait
time to the originally intended 1 second.
Before we can send a message to the mailbox we have to check that there
is space to do so. Therefore we poll the status register. But up to now
the wrong status register, the one of mailbox 0, was checked. Fix this
by polling the status regiser of mailbox 1.
Signed-off-by: Fabian Vogt <fvogt@suse.com> Acked-by: Stephen Warren <swarren@wwwdotorg.org>
[mb: rename registers and update commit message] Signed-off-by: Matthias Brugger <mbrugger@suse.com>
Tom Rini [Fri, 6 Sep 2019 12:04:08 +0000 (08:04 -0400)]
Merge tag 'efi-2019-10-rc4-3' of https://gitlab.denx.de/u-boot/custodians/u-boot-efi
Pull request for UEFI sub-system for v2019.10-rc4 (3)
This includes the patches from
Pull request for UEFI sub-system for v2019.10-rc4 (2)
Fix UEFI specification compliance issues in the simple network protocol:
* Correctly set and reset the interrupt status.
* Support filling the header in the Transmit() service.
* Correct the checking and setting of the network state.
* Implement the MCastIPtoMAC() service.
* Adjust the simple network protocol unit test.
Fix UEFI specification compliance issues in the protocol.
Fix UEFI specification compliance issues in the simple text output protocol:
* Avoid out of bounds cursor position.
* Do not set illegal screen mode.
Fix UEFI specification compliance issues in the block IO protocol:
* Check parameters.
* Return correct status code if buffer is unaligned.
Refactor initialization of EFI memory in preparation of support for
> 3GB memory on x86.
The sdhci capabilities registers can be incorrect. The
sdhci-caps-mask and sdhci-caps dt properties specify which bits of
the registers are incorrect and what their values should be. This
patch makes the sdhci driver use those properties to correct the caps.
Also use "dev_read_u64_default" instead of "dev_read_u32_array" for
caps mask.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
dm: core: Add functions to read 64-bit dt properties
This patch adds functions dev_read_u64_default & dev_read_u64
to read unsigned 64-bit values from devicetree.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
When backspacing in column 0 do no set the column index to ULONG_MAX.
Ensure that the row number is not set to ULONG_MAX even if the row count is
advertised as 0.
Ignore control characters other the 0x08, 0x0a, 0x0d when updating the
column.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Park, Aiden [Tue, 3 Sep 2019 17:43:43 +0000 (17:43 +0000)]
efi_loader: Extract adding a conventional memory in separate routine
Adding a conventional memory region to the memory map may require ram_top
limitation and it can be also commonly used. Extract adding a conventional
memory to the memory map in a separate routine for generic use.
Signed-off-by: Aiden Park <aiden.park@intel.com> Tested-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
GetStatus() must clear the interrupt status.
Transmit() should set the TX interrupt.
Receive() should clear the RX interrupt.
Initialize() and Start() should clear the interrupt status.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
As stated in commit a61a4a1db009e3e600258551a01b54c4f50ec103 with DM_MMC,
exynos boards now enumarates external SD/MMC slot as mmc2, instead of mmc1
with legacy mode. Moving mmc2 before mmc1/0 restore the previous behavior
of trying external SD/MMC before internal slot.
Signed-off-by: Guillaume GARDET <guillaume.gardet@arm.com> Cc: Lukasz Majewski <lukma@denx.de> Cc: Anand Moon <linux.amoon@gmail.com> Cc: Simon Glass <sjg@chromium.org> Cc: Minkyu Kang <mk7.kang@samsung.com> Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Kever Yang [Thu, 29 Aug 2019 07:42:41 +0000 (15:42 +0800)]
mmc: dw_mmc: fix timeout calculate method
There are two cases not been considered:
- use uint for timeout, it will overflow when size bigger than 512KB for
it *8*1000 at the beginning, but we may use size up to 32MB; The
'timeout' will overflow if size bigger than 51.2MB after this fix, which
should be enough for U-Boot;
- The timeout is using clock speed for data rate, but the device may not
have such high speed, eg. clock is 52MHz while the device write speed may
be less than 10MB/s, and we may use up to 150MHz clock.
Fix them in this patch, the max timeout is about 6500 when size is 32MB
after fix.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Sam Protsenko [Wed, 14 Aug 2019 19:52:51 +0000 (22:52 +0300)]
mmc: Rename timeout parameters for clarification
It's quite hard to figure out time units for various function that have
timeout parameters. This leads to possible errors when one forgets to
convert ms to us, for example. Let's rename those parameters
correspondingly to 'timeout_us' and 'timeout_ms' to prevent such issues
further.
While at it, add time units info as comments to struct mmc fields.
This commit doesn't change the behavior, only renames parameters names.
Buildman should report no changes at all.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org> Reviewed-by: Peng Fan <peng.fan@nxp.com> Reviewed-by: Igor Opaniuk <igor.opaniuk@gmail.com>
Sam Protsenko [Wed, 14 Aug 2019 19:52:50 +0000 (22:52 +0300)]
mmc: Fix timeout values passed to mmc_wait_dat0()
mmc_wait_dat0() expects timeout argument to be in usec units. But some
overlying functions operate on timeout in msec units. Convert timeout
from msec to usec when passing it to mmc_wait_dat0().
This fixes 'avb' commands on BeagleBoard X15, because next chain was
failing:
when passing incorrect timeout from __mmc_switch() to mmc_wait_dat0().
Fixes: bb98b8c5c06a ("mmc: During a switch, poll on dat0 if available and check the final status") Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org> Reviewed-by: Eugeniu Rosca <rosca.eugeniu@gmail.com> Tested-by: Eugeniu Rosca <rosca.eugeniu@gmail.com> Reviewed-by: Peng Fan <peng.fan@nxp.com> Tested-by: Igor Opaniuk <igor.opaniuk@gmail.com> Reviewed-by: Igor Opaniuk <igor.opaniuk@gmail.com>
With GCC 9.2.1 net/nfs.c leads to multiple errors of type
address-of-packed-member.
net/nfs.c: In function ‘rpc_req’:
net/nfs.c:199:18: error: taking address of packed member of
‘struct rpc_t’ may result in an unaligned pointer value
[-Werror=address-of-packed-member]
199 | p = (uint32_t *)&(rpc_pkt.u.call.data);
| ^~~~~~~~~~~~~~~~~~~~~~
net/nfs.c: In function ‘nfs_readlink_reply’:
net/nfs.c:631:46: error: taking address of packed member of
‘struct rpc_t’ may result in an unaligned pointer value
[-Werror=address-of-packed-member]
631 | nfs3_get_attributes_offset(rpc_pkt.u.reply.data);
| ~~~~~~~~~~~~~~~^~~~~
LD drivers/block/built-in.o
net/nfs.c: In function ‘nfs_read_reply’:
net/nfs.c:692:46: error: taking address of packed member of
‘struct rpc_t’ may result in an unaligned pointer value
[-Werror=address-of-packed-member]
692 | nfs3_get_attributes_offset(rpc_pkt.u.reply.data);
| ~~~~~~~~~~~~~~~^~~~~
struct rpc_t is only used as local variable. It is naturally packed. So
there is no need for the attribute packed.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
env: net: U_BOOT_ENV_CALLBACKs should not depend on CMD_NET
Some environment variables are relevant for networking. For these
U_BOOT_ENV_CALLBACKs have been defined. When the corresponding environment
variable is updated the callback updates the state of the network
sub-system.
In the UEFI subsystem we can use the network even if CONFIG_CMD_NET is not
defined.
Let the usage of the U_BOOT_ENV_CALLBACKs depend on CONFIG_NET and not on
CONFIG_CMD_NET.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
liucheng (G) [Thu, 29 Aug 2019 13:47:40 +0000 (13:47 +0000)]
CVE: nfs: fix stack-based buffer overflow in some nfs_handler reply helper functions
This patch adds a check to nfs_handler to fix buffer overflow for CVE-2019-14197,
CVE-2019-14200, CVE-2019-14201, CVE-2019-14202, CVE-2019-14203 and CVE-2019-14204.
Signed-off-by: Cheng Liu <liucheng32@huawei.com> Reported-by: Fermín Serna <fermin@semmle.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Michael Walle [Tue, 27 Aug 2019 08:13:52 +0000 (10:13 +0200)]
net: make net_random_ethaddr() more random
The net_random_ethaddr() tries to get some entropy from different
startup times of a board. The seed is initialized with get_timer() which
has only a granularity of milliseconds. We can do better if we use
get_ticks() which returns the raw timer ticks. Using this we have a
higher chance of getting different values at startup.
Signed-off-by: Michael Walle <michael@walle.cc> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Stefan Roese [Mon, 26 Aug 2019 07:18:11 +0000 (09:18 +0200)]
net: macb: Fix rx buffer cache handling
With commit c6d07bf440bc ("net/macb: increase RX buffer size for GEM")
ethernet support does not work any more with d-cache enabled on the
AT91SAM. The reason is, that MACB_RX_BUFFER_SIZE was changed from 4096
to 128 but this change was not refected in the rx_buffer flush and
invalidate functions, as these also use this macro.
This patch now fixes this by calculating the rx buffer size correctly
again in those functions. With this change, ethernet works again
reliably on my AT91SAM board.
Signed-off-by: Stefan Roese <sr@denx.de> Fixes: c6d07bf440bc ("net/macb: increase RX buffer size for GEM") Cc: Ramon Fried <rfried.dev@gmail.com> Cc: Eugen Hristev <eugen.hristev@microchip.com> Cc: Anup Patel <anup.patel@wdc.com> Cc: Bin Meng <bmeng.cn@gmail.com> Cc: Joe Hershberger <joe.hershberger@ni.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Tested-by: Bin Meng <bmeng.cn@gmail.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
projects / u-boot.git / log