Chris Packham [Thu, 3 Dec 2020 03:24:29 +0000 (16:24 +1300)]
powerpc: mpc85xx: Allow boards to override CONFIG_USB_MAX_CONTROLLER_COUNT
If the board isn't strapped to enable USB1 then attempting to access it
will result in a hang. Avoid this by allowing boards to define
CONFIG_USB_MAX_CONTROLLER_COUNT.
Signed-off-by: Chris Packham <judge.packham@gmail.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Alban Bedel [Tue, 17 Nov 2020 15:20:04 +0000 (16:20 +0100)]
armv8: fsl-layerscape: Fix automatic setting of bootmcd with TF-A
When booting from TF-A there is a logic that attempt to detect if the
default environment is used, if this is the case it then set the
`bootcmd` and `mcinitcmd` depending of the device we booted from.
This detection logic is dubious as it access internals of the env
implementation and it doesn't always work correctly.
First of all it detect any valid environment as not being the
default, so after running `env default -a && saveenv` the board
doesn't boot anymore as `bootcmd` is then empty.
But it also fails in some other ways, for example it always detect a
default environment when redundant env is enabled on MMC, so in that
case `bootcmd` is overwritten on every boot.
Instead of increasing the complexity of the detection just check if
`bootcmd` and `mcinitcmd` are set in the environment and set them if
they are not.
Signed-off-by: Alban Bedel <alban.bedel@aerq.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
armv8: lx2162a: Add Soc changes to support LX2162A
LX2162 is LX2160 based SoC, it has same die as of LX2160
with different packaging.
LX2162A support 64-bit 2.9GT/s DDR4 memory, i2c, micro-click module,
microSD card, eMMC support, serial console, qspi nor flash, qsgmii,
sgmii, 25g, 40g, 50g network interface, one usb 3.0 and serdes
interface to support three PCIe gen3 interface.
Tom Rini [Wed, 9 Dec 2020 16:36:41 +0000 (11:36 -0500)]
Merge tag 'u-boot-stm32-20201209' of https://gitlab.denx.de/u-boot/custodians/u-boot-stm
- Manage CONFIG_ENV_EXT4_DEVICE_AND_PART in stm32mp1 board
- Update ARM STI and ARM STM STM32MP Arch maintainers emails
- Enable internal pull-ups for SDMMC1 on DHCOM SoM
The STM32MP1 DHCOM SoM can be built with either bus voltage level shifter
or without one on the SDMMC1 interface. Because the SDMMC1 interface is
limited to 50 MHz and hence SD high-speed anyway, disable the SD feedback
clock to permit operation of the same U-Boot image on both SoM with and
without voltage level shifter.
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Patrice Chotard <patrice.chotard@st.com> Cc: Patrick Delaunay <patrick.delaunay@st.com> Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Marek Vasut [Tue, 1 Dec 2020 10:29:17 +0000 (11:29 +0100)]
ARM: dts: stm32: Enable internal pull-ups for SDMMC1 on DHCOM SoM
The default state of SD bus and clock line is logical HI. SD card IO is
open-drain and pulls the bus lines LO. Always enable the SD bus pull ups
to guarantee this behavior on DHCOM SoM. Note that on SoMs with SD bus
voltage level shifter, the pull ups are built into the level shifter,
however that has no negative impact.
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Patrice Chotard <patrice.chotard@st.com> Cc: Patrick Delaunay <patrick.delaunay@st.com> Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Manuel Reis [Wed, 25 Nov 2020 10:16:20 +0000 (10:16 +0000)]
add check for ignored CONFIG_ENV_EXT4_DEVICE_AND_PART definition
Check whether user has explicitly defined device and partition where
environment file will be located before using 'auto' i.e. bootable
partition
Voids the need to set such partition as bootable to work with the
'dev:auto' tuple
Signed-off-by: Manuel Reis <mluis.reis@gmail.com> Cc: Patrick Delaunay <patrick.delaunay@st.com> Cc: Patrice Chotard <patrice.chotard@st.com> Tested-by: Michael Opdenacker <michael.opdenacker@bootlin.com> Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
- Espressobin: Simplify DT handling of board variants (Pali)
- Add Luka Perkov to maintainers of Puzzle-M801 (Luka)
- Armada 38x: Enable board specific USB2 high-speed impedance
threshold configuration (Joshua)
Pali Rohár [Wed, 25 Nov 2020 18:20:09 +0000 (19:20 +0100)]
arm: mvebu: Espressobin: Add support for emmc into dts file
To simplify setup, configuration and compilation of u-boot, define emmc
node for all Espressobin boards. Espressobin boards without populated emmc
works correctly, just detection and initialization of emmc obviously fails.
Code for emmc is extracted from commit f1a43c84a960 ("arm64: dts: a3720:
add support for espressobin with populated emmc").
Hardware testing of a board using the Armada 385 has shown that an
impedance threshold setting of 0x7 performs better in an eye-diagram
test than with Marvell's recommended value 0x6.
As other boards may still perform better with Marvell's reccomended value,
a configuration option is added with a default value of 0x6.
Signed-off-by: Joshua Scott <joshua.scott@alliedtelesis.co.nz> Reviewed-by: Stefan Roese <sr@denx.de>
Marcel Ziswiler [Thu, 22 Oct 2020 08:21:40 +0000 (11:21 +0300)]
imx8: allow overriding memory layout
Introduce weak function board_mem_get_layout() which allows overriding
the memory layout from board code in runtime, useful for handling
different SKU versions.
Igor Opaniuk [Thu, 22 Oct 2020 08:21:38 +0000 (11:21 +0300)]
board: toradex: add apalis-imx8x 2gb wb it v1.1a module support
This commit adds initial support for the Toradex Apalis iMX8X 2GB WB
IT V1.1A System on Module support [1].
Boot log:
U-Boot 2020.10-02940-g894aebb7e8-dirty (Oct 22 2020 - 09:43:57 +0300)
CPU: NXP i.MX8QXP RevB A35 at 1200 MHz at 30C
DRAM: 2 GiB
MMC: FSL_SDHC: 0, FSL_SDHC: 1
Loading Environment from MMC... OK
In: serial@5a070000
Out: serial@5a070000
Err: serial@5a070000
Model: Toradex Apalis iMX8 QuadXPlus 2GB Wi-Fi / BT IT V1.1A,
Serial# 06617018
Net: eth0: ethernet@5b040000 [PRIME]
Hit any key to stop autoboot: 0
Functionality wise the following is known to be working:
- eMMC and MMC/SD card
- Ethernet (*)
- GPIOs
- I2C
Unfortunately, there is no USB functionality for the i.MX 8QXP as of
yet.
* With the SCU FW from the latest Toradex BSP 5.0.0 (SCU FW 1.5.1)
ETH PHY encounters bring up problems after reset, this will be fixed
soon on SCU FW side.
[1] https://www.toradex.com/computer-on-modules/apalis-arm-family/nxp-imx-8x Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com> Acked-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Tim Harvey [Fri, 25 Sep 2020 15:08:35 +0000 (08:08 -0700)]
imx8m: fix cache setup for dynamic sdram size
the mem_map structure containing the size of SDRAM is used in various
cache functions in cache_v8.c thus we need to update it with the
sdram size the board is configured with as well. Without this
the cache functions do not get setup properly and can hang
in the case where a board reports more SDRAM than defined in
PHYS_SDRAM_SIZE.
Max Krummenacher [Wed, 28 Oct 2020 09:58:11 +0000 (11:58 +0200)]
ARM: dts: imx8mm-verdin: follow changed pmic
The used PMIC has been changed from RHOM BD71837 to NXP PCA9450A.
Adjust the device tree accordingly.
Remove the old ADC node as the ADC has been changed and has no longer
a separate power rail.
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com> Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com> Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Haibo Chen [Tue, 3 Nov 2020 09:18:35 +0000 (17:18 +0800)]
mmc: fsl_esdhc_imx: optimize the timing setting
For imx usdhc/esdhc, once set the DDR_EN, enable the DDR mode, the
card clock will be divied by 2 automatically by the host. So need
to first config the DDR_EN correctly, then update the card clock.
This will make sure the actual card clock is as our expected.
IC also suggest config the DDR_EN firstly, then config the clock
divider.
For HS400/HS400ES mode, need to config the strobe dll, this need
to based on the correct target clock rate, so need to do this after
clock rate is update.
Commit f692b479f02d changed the VPD partition name from "vpd" to
"vpd@0". Fix the VPD reader code to use the new name, so that
the VPD code keeps working.
Fixes: f692b479f02d ("i2c: eeprom: Use reg property instead of offset and size") Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Oliver Graute [Fri, 6 Nov 2020 08:09:30 +0000 (09:09 +0100)]
imx: ahab: fix compiler warnings in debug
arch/arm/mach-imx/imx8/ahab.c: In function ‘authenticate_os_container’:
arch/arm/mach-imx/imx8/ahab.c:96:9: warning: format ‘%x’ expects argument of type
‘unsigned int’, but argument 9 has type ‘ulong {aka long unsigned int}’ [-Wformat=]
debug("img %d, dst 0x%x, src 0x%x, size 0x%x\n",
Oliver Graute [Fri, 6 Nov 2020 08:09:31 +0000 (09:09 +0100)]
imx: ahab: Fix compiler warnings in printf
arch/arm/mach-imx/imx8/ahab.c:110:63: warning: format ‘%x’ expects
argument of type ‘unsigned int’, but argument 2 has type ‘u64 {aka long
long unsigned int}’ [-Wformat=]
Patrick Delaunay [Thu, 18 Jun 2020 07:41:34 +0000 (09:41 +0200)]
configs: cei-tk1-som: remove CONFIG_ARMV7_PSCI in include file
Activate ARCH_SUPPORT_PSCI as other TEGRA124 target and remove
CONFIG_ARMV7_PSCI and CONFIG_ARMV7_PSCI_NR_CPUS in configs file as they
are migrated in Kconfig.
Select CONFIG_ARMV7_PSCI_0_1 (the first PSCI version),
because CONFIG_ARMV7_PSCI_0_2 and CONFIG_ARMV7_PSCI_1_0
are not activated in this product.
Hi,
This patch depend on the previous serie [1].
I don't test this patch on real hardware but
after this patch the size of the binary don't change.
In .config we have:
CONFIG_ARCH_SUPPORT_PSCI=y
CONFIG_ARMV7_PSCI=y
# CONFIG_ARMV7_PSCI_1_0 is not set
# CONFIG_ARMV7_PSCI_0_2 is not set
CONFIG_ARMV7_PSCI_0_1=y
CONFIG_ARMV7_PSCI_NR_CPUS=4
In u-boot.cfg, this patch only add the 2 lines
#define CONFIG_ARCH_SUPPORT_PSCI 1
#define CONFIG_ARMV7_PSCI_0_1 1
[1] "Convert CONFIG_ARMV7_PSCI_1_0 and CONFIG_ARMV7_PSCI_0_2 to Kconfig"
http://patchwork.ozlabs.org/project/uboot/list/?series=184029
Regards
Patrick
END
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Reviewed-by: Peter Chubb <peter.chubb@data61.csiro.au> Signed-off-by: Tom Warren <twarren@nvidia.com>
Peter Robinson [Wed, 1 Apr 2020 23:28:55 +0000 (00:28 +0100)]
arm: tegra: add options for BOOTENV_EFI_SET_FDTFILE_FALLBACK for tegra186
Upstream linux DT naming doesn't align with the U-Boot DT, which may
not always be the case so this allows using BOOTENV_EFI_SET_FDTFILE_FALLBACK
where it might be appropriate for some boards.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
Peter Robinson [Wed, 1 Apr 2020 23:28:54 +0000 (00:28 +0100)]
arm: tegra: define fdtfile option for distro boot
For booting via UEFI we need to define the fdtfile option so
bootefi has the option to load a fdtfile from disk. For arm64
the kernel dtb is located in a vendor directory so we define
that as nvidia for that architecture.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
colibri_t30: fix spi1 and uart2/3 resp. uartb/c pinmuxing
Fix SPI1 and UART2/3 resp. UARTB/C pinmuxing.
Note: The former was illegally muxing multiple SoC balls onto the same
internal SoC signal which caused rather strange behaviour regarding
the RS232 serial transceiver ForceOFF# pins as available on Iris.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
apalis/colibri_t30: add comment about tristate and input vs. output pinmuxing
Add pinmuxing comment stating that TRISTATE means the output driver is
tri-stated and INPUT means the input driver is enabled vs. OUTPUT where
it is disabled.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
projects / u-boot.git / log