Stefano Babic [Mon, 18 Oct 2010 08:23:05 +0000 (10:23 +0200)]
MX31: add delay between USB port setup and reset
Sometimes a usb tree is not popolated after a system reset.
It seems a delay is required after setting the USB ports
for the MX.31 before resetting the ehci controller.
Ben Gardiner [Thu, 14 Oct 2010 21:26:32 +0000 (17:26 -0400)]
da850evm: fix linux bootparam address
This patch fixes the LINUX_BOOT_PARAM_ADDR define to be based off of
PHYS_SDRAM_1 instead of CONFIG_SYS_MEMTEST_START. On da830 they are the same
thing but on da850 the CONFIG_SYS_MEMSTART define is offset from the
PHYS_SDRAM_1 start.
Without this patch it is not possible to boot linux on da850 -- bootm hangs
at "Uncompressing Linux... done, booting the kernel."
Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Ben Gardiner [Thu, 14 Oct 2010 21:26:29 +0000 (17:26 -0400)]
da850evm: basic MII EMAC support
The current da850evm support in u-boot/master omits any use of
the davinci EMAC. This patch adds basic support for the EMAC using
the MII PHY found on the baseboard of the EVM. The MAC address is
read from the environment variable 'ethadd'. Note that this is
different from the da850evm support in the u-boot omapl1 tree
where the MAC address is read from SPI flash.
Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca> CC: Sandeep Paulraj <s-paulraj@ti.com> CC: Sudhakar Rajashekhara <sudhakar.raj@ti.com> CC: Ben Warren <biggerbadderben@gmail.com> CC: Mike Frysinger <vapier@gentoo.org> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Ben Gardiner [Thu, 14 Oct 2010 21:26:25 +0000 (17:26 -0400)]
da850evm: setup NAND support under CONFIG_USE_NAND
The current da850evm config is missing the pieces for NAND support that can be
found in Sandeep's u-boot-davinci tree [1].
This patch adds NAND support in the spirit of the support in the u-boot-davinci
tree where NAND support for the da850evm can be enabled by putting a single
'#define CONFIG_USE_NAND' at the top of the include/configs/da850evm.h file.
Ben Gardiner [Thu, 14 Oct 2010 21:26:22 +0000 (17:26 -0400)]
da850evm: setup the NAND flash timings
The default NAND flash timings are very conservative. This patch assigns the
timings reccomended in the recent linux kernel patch [1] from Sekhar Nori. The
speedup, as reported in that patch, is 5.3x for reads.
Ben Gardiner [Thu, 14 Oct 2010 21:26:19 +0000 (17:26 -0400)]
da850evm : enable NAND even when not in NAND boot mode
There is currently no NAND pinmux enabled by the da850evm board setup code.
This is fine when booting from NAND since the early boot code (UBL) will setup
the pinmux; however, when the boot mode is any other setting NAND is unusable
when enabled in the config.
This patch adds a pinmux list for NAND and enables it when NAND is enabled in
the config. Tested by booting from SPI on the da850evm and verifying NAND
was usable.
Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca> CC: Nick Thompson <nick.thompson@ge.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Ben Gardiner [Thu, 14 Oct 2010 21:26:17 +0000 (17:26 -0400)]
davinci_nand, trivial : use symbolic ECC start command
The ECC calculations were started by writing 1 << 13 to the nand FCR register;
that value is also defined as DAVINCI_NANDFCR_4BIT_CALC_START in emif_defs.h.
This patch substitutes the macro DAVINCI_NANDFCR_4BIT_CALC_START for the
magic number '1 << 13'.
Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
The IGEP module is a low-power, high performance production-ready
system-on-module (SOM) based on TI's OMAP3 family.The IGEP module
solution based upon TI OMAP3 provides a low-power/low-cost platform
for a variety of consumer/industrial/medical devices.
Signed-off-by: Enric Balletbo i Serra <eballetbo@gmail.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
The IGEP v2 board is a low-cost, fan-less and industrial temperature
range single board computer that unleashes laptop-like performance and
expandability without the bulk, expense, or noise of typical desktop
machines. Its architecture shares much in common with other OMAP3 boards.
Signed-off-by: Enric Balletbo i Serra <eballetbo@gmail.com> Acked-by: Steve Sakoman <steve.sakoman@linaro.org> Tested-by: Steve Sakoman <steve.sakoman@linaro.org> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Steve Sakoman [Fri, 1 Oct 2010 04:46:52 +0000 (21:46 -0700)]
ARMV7: OMAP3: Fix bug in get_sdr_cs_offset()
This patch fixes a typo in the routine to calculate the cs offset
based upon the contents of the SDRC cs_cfg register. This function
mistakenly shifts the CS1STARTLOW field 17 bits right instead of
17 bits left.
This hasn't been an issue to date because all OMAP3 boards currently
are configured to have zeros in this field.
Reported-by: Peter Maydell <peter.maydell@linaro.org> Signed-off-by: Steve Sakoman <steve.sakoman@linaro.org>
The current mmc driver returns erroneous capacity information for
eMMC. The capacity of eMMC devices is available only in the ext-CSD
register. This patch add code to read the ext-CDSD register and
correctly calculate eMMC capacity.
Signed-off-by: Sukumar Ghorai <s-ghorai@ti.com> Acked-by: Steve Sakoman <steve@sakoman.com>
Stefan Roese [Tue, 12 Oct 2010 07:39:45 +0000 (09:39 +0200)]
ns16550: Add WATCHDOG_RESET to putc for short watchdog timeout boards
Call watchdog_reset() upon newline. This is done here in putc
since the environment code uses a single puts() to print the complete
envrironment upon "printenv". So we can't put this watchdog call
in puts().
This is needed for boards with a very short watchdog timeout, like the
lwmon5 with a 100ms timeout. Without this patch this board resets in the
commands with long outputs, like "printenv" or "fdt print".
Note that the image size is not increased with this patch when
CONFIG_HW_WATCHDOG or CONFIG_WATCHDOG are not defined since the compiler
optimizes this additional code away.
Signed-off-by: Stefan Roese <sr@denx.de>
Fix typo in comment. Signed-off-by: Wolfgang Denk <wd@denx.de>
Steve Sakoman [Mon, 11 Oct 2010 12:51:39 +0000 (05:51 -0700)]
env_mmc: Fix crashing bug encountered after enabling ARM relocation
The crash was occuring in env_relocate because it was being called prior
to mmc_initialize. This patch moves the MMC initialization earlier in
the init process.
This patch also cleans up the env_relocate_spec code in env_mmc.c
Signed-off-by: Steve Sakoman <steve.sakoman@linaro.org> Acked-by: Stefano Babic <sbabic@denx.de>
Originally the Makefile defines CONFIG_ADS5121_REV2 when configuring
for board mpc5121ads_rev2. The config in include/configs/mpc5121ads.h
expects a define CONFIG_MPC5121ADS_REV2 for this.
Therefore there are two defines used but only 1 is defined.
This patch renames references to CONFIG_ADS5121_REV2 to CONFIG_MPC5121ADS_REV2
to have one common define.
This patch fixes faulty mem size detection caused by wrong config in
include/configs/mpc5121ads.h
Signed-off-by: Mark Vels <mark.vels@team-embedded.nl>
common/libcommon.a(fdt_support.o): In function `fdt_add_edid':
/local/hudson/jobs/mirrors-u-boot.git/workspace/common/fdt_support.c:1205: undefined reference to `fdt_increase_size'
make: *** [u-boot] Error 1
Signed-off-by: Matthew McClintock <msm@freescale.com> Signed-off-by: Anatolij Gustschin <agust@denx.de>
Stefano Babic [Tue, 29 Jun 2010 09:47:48 +0000 (11:47 +0200)]
FPGA: add support for downloading Lattice bitstream
The patch adds support to load a Lattice's bitstream
image (called VME file) into a Lattice FPGA. The code
containing the state machine delivered as part of
Lattice's ispVMtools is integrated.
The FPGA is programmed using the JTAG interface. The
board maintainer must provide accessors to drive the
JTAG signals TCK, TMS, TDI and to get the value of the
input signal TDO.
Bryan Wu [Mon, 9 Aug 2010 18:58:24 +0000 (14:58 -0400)]
usb: musb: only write CLRDATATOG when appropriate
This is a change similar to what is already in the Linux driver. We
should only program the CLRDATATOG bit when the current mode indicates
that it is needed.
Signed-off-by: Bryan Wu <bryan.wu@analog.com> Signed-off-by: Cliff Cai <cliff.cai@analog.com> Signed-off-by: Mike Frysinger <vapier@gentoo.org>
usb: Add support for multiple-LUN mass storage devices
This patch changes `usb_stor_scan' to scan all the LUNs of each mass
storage device. It also fixes the various commands to correctly set
the LUN field.
Notably, it allows each LUN of GuruPlug's microSD card reader to be
accessed.
After gadget reinitializaton (after tftp has been done once)
packet_received may become equal to 1 due to nuking OUT_EP
while disabling it in eth_reset_config.
rx_submit called from usb_eth_init queues rx_req first time.
But the first call of usb_eth_recv from NetLoop queues rx_req
again due to packet_received = 1.
The following flow shows the path of functions calls when
this happens:
net/net.c:NetLoop
|
+-net/eth.c:eth_init
| ether.c:usb_eth_init
| |
| +-udc_driver:usb_gadget_handle_interrupts
| | udc_driver:...
| | ether.c:eth_setup
| | ether.c:eth_set_config
| | ether.c:eth_reset_config
| | udc_driver:usb_ep_disable
| | udc_driver:nuke
| | ether.c:rx_complete
| | ether.c: packet_received = 1;
| |
| +-ether.c:rx_submit
| udc_driver:usb_ep_queue --- The first time when rx_req is queued
|
+-net/eth.c:eth_rx
ether.c:usb_eth_recv
|
+-udc_driver:usb_gadget_handle_interrupts
| udc_driver:... --- no interrupts, returning
+-ether.c: if (packet_received) { ...
ether.c:rx_submit
udc_driver:usb_ep_queue --- The second time!
Remove and fix needless and destructive operations with tx/rx_req.
1) 'req' in rx_complete is always not NULL and always equals to rx_req
2) Free allocated tx_req if rx_req allocation has failed
3) Do not zero out tx/rx_req in usb_eth_init, leave this for
eth_reset_config which will be called at the next use of usb0
4) Additional check in usb_eth_recv is not required
This patch fixes an error when running MAKEALL for ARM9.
On OS X /bin/sh uses builtin echo which does not utilise '-n' switch.
GNU manual for builtins recomend to use here-document style to solve
this portability issue.
This patch removes the usage of 'echo -n' and replace by here-document
style or a oneline echo command.
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com> CC: Peter Pearse <peter.pearse@arm.com>
Matt Waddel [Thu, 7 Oct 2010 21:48:46 +0000 (15:48 -0600)]
ARMV7: Fixed baudrate setting in pl01x driver
The pl01x serial driver was lacking the code to switch baudrates from the
command line. Fixed by simply saving the new baudrate and calling
serial_init() again. Also fixed CamelCase variables, I/O accessors and
comment style.
Signed-off-by: Matt Waddel <matt.waddel@linaro.org>
Matt Waddel [Thu, 7 Oct 2010 21:48:45 +0000 (15:48 -0600)]
ARMV7: Versatile Express Coretile CortexA9x4 support
Adds support for the ARM quad-core Cortex-A9 processor
This system includes a motherboard(Versatile Express), daughterboard
(Coretile), and SOC(Cortex-A9 quad core). The serial port, ethernet,
and flash systems work with these additions. The naming convention
is:
SOC -> CortexA9 quad core = ca9x4
daughterboard -> Coretile = ct
motherboard -> Versatile Express = vxp
This gives ca9x4_ct_vxp.c as the board support file.
Signed-off-by: Matt Waddel <matt.waddel@linaro.org>
There were some #undef's of CONFIG_SYS_ARM_WITHOUT_RELOC added to a few board
configs as part of the arm relocation series; but these are not needed now as we
do not #undef what is not #defined in the first place.
Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca> CC: Heiko Schocher <hs@denx.de>
It is observed that, in most of the board configs the code is being
duplicated, also for any common change all board files needs update
This issue was under discussion from long on mailing list and we
converge on introducing common config file.
With this patch-
1. Total Kirkwood specific configuration code is reduced by 210 lines
2. All common configuration can be shared by multiple boards
3. Easy to manage common updates like ARM relocation changes
mv-common.h file is added to include/configs/
It contains all common configuration supported for all Kirkwood boards
The respective board configs are updated for its usage
Build tested for guruplug, mv88f6281gtw_ge, openrd_base,
rd6281a and sheevaplug
Binary execution tested for sheevaplug
Todo:
1. Other custom Kirkwood boards to be synced
2. The support to be extended for Orion5X based boards
For all Kirkwood boards so far dram_init function is duplicated
dram_init function is moved to dram.c and relevant code from all
board specific files removed
If any board needs specific dram init handling than standard one,
then, a macro CONFIG_SYS_BOARD_DRAM_INIT should be defined in
board config header file and the dram_init function can be put
in board specific source file
For ex. keymile boards
Kirkwood: print_cpuinfo fixed for valid devid revid
Earlier Device Identification register was used to detect
the type for SoC, considering 88F6282 support to be added,
It is not possible to detect the same using current
algorithm.
With this patch, device ID is being read using PCIE devid
register, also valid chip revision ID will also be read and
displayed
Albert Aribaud [Thu, 16 Sep 2010 15:00:30 +0000 (20:30 +0530)]
mvsata_ide: adjust port init sequence
mvsata_ide_initialize_port(): adjust init sequence (SStatus
should be checked only after all writes to SControl) and
return success/failure to ide_preinit().
Also, as some tests showed init durations in the hundreds
of us, raise the time-out to 01 ms to be on the safe side.
Signed-off-by: Albert Aribaud <albert.aribaud@free.fr>
Reinhard Meyer [Tue, 5 Oct 2010 14:56:39 +0000 (16:56 +0200)]
sf: turn probe switch into a lookup table
This allows for arbitrarily long manufacturer ids following the JEDEC
standard of 0x7f continuation bytes. It also makes adding new entries
easier as it's just one element in an array. The downside is that it
increases code size a bit, but we're talking ~50 bytes.
Signed-off-by: Reinhard Meyer <u-boot@emk-elektronik.de> Signed-off-by: Mike Frysinger <vapier@gentoo.org>
This patch does 2 things:
- Fix the argument number assigned to the vdw (VME data width) value.
Previously, a nonexistent 7th arument was read as the vdw variable.
- Reduce the size of the argument array for the tsi148 command from
8 to 7. The tsi148 command itself is argument index 0, and the
maximum number arguments passed to the command is 6, making a total
of 7 for the array.
Signed-off-by: Brent Darley <bdarley@xes-inc.com> Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Peter Tyser [Wed, 15 Sep 2010 00:13:52 +0000 (19:13 -0500)]
ppmc7xx: Use _start as reset entry point
Previously the _warm_start label was used as an entry point. These 2
entry points should be functionally identical after the removal of the
BOOTFLAG_WARM define.
Stefan Roese [Mon, 13 Sep 2010 09:10:34 +0000 (11:10 +0200)]
cp/cmp: Add WATCHDOG_RESET in copy and compare loop
On some boards with a very short watchdog timeout, the "cp" and
"cmp" commands may reset the board. This patch adds some
watchdog resets inside the loops. Otherwise for example the lwmon5
board will reset while doing something like this:
Peter Tyser [Sun, 12 Sep 2010 22:38:49 +0000 (17:38 -0500)]
examples/standalone: Use gcc's -fno-toplevel-reorder
Using -fno-toplevel-reorder causes gcc to not reorder functions. This
ensures that an application's entry point will be the first function in
the application's source file.
This change, along with commit 620bbba524fbaa26971a5004793010b169824f1b
should cause a standalone application's entry point to be at the base of
the compiled binary. Previously, the entry point could change depending
on gcc version and flags.
Note -fno-toplevel-reorder is only available in gcc version 4.2 or
greater.
a4m072: support for SHOW_BOOT_PROGRESS feature using LED display
This patch adds support for displaying boot progress codes on a4m072 board
using LED display. As we can display only one symbol at any time on the hardware
(two symbols with blinking) we can't display progress codes directly and have
to map them to 2-symbol codes.
We use the following mapping on the a4m972 board:
[1, 8] U [100, 108] -> 5
[-9, -1] U [-101, -100] U [-113, -103] -> -5
[9, 14] U [120, 123] U [125, 129] -> 8
[-13, -10] U [-122, -120] U [-127, -124] U {-129} -> -8
{15} -> 9
[-32, -30] -> -A
[-40, -35] U [-51, -42] U [-58, -53] U
[-83, -80] U {-64, -130, -140, -150} -> -B
Other progress code are ignored. One symbol codes are displayed steady while
two-symbol codes are displayed using blinking. Boot progress codes are
displayed with decimal got unset (as opposed to 'display' command output).
This patch adds support for LED display on a4m072 board. Hardware is
capable of displaying only one symbol at any time. We support displaying
two symbols in software (via blinking).
led_display: split led display support into generic and hw-dependent parts
Split the display command into generic interface and hardware-specific
realization for PDSP188x LED display found on hmi1001 and manroland
boards. Simple interface for LED displays is defined in
include/led-display.h and described in doc/README.LED_display.
Driver-specific implementation was moved into drivers/misc/pdsp188x.c
file (enabled with CONFIG_PDSP188x set).
This patch provides support for the A4M072 board with the following features:
UART
NOR flash
FEC Ethernet
External SRAM
I2C EEPROM
CompactFlash cards on IDE/ATA port
USB Host
PCI initialization
The 7-segment LED indicator is not yet supported.
Signed-off-by: Sergei Poselenov <sposelenov@emcraft.com>
VFAT: fix processing of scattered long file name entries
The U-Boot code has the following bugs related to the processing of Long File
Name (LFN) entries scattered across several clusters/sectors :
1) get_vfatname() function is designed to gather scattered LFN entries by
cluster chain processing - that doesn't work for FAT12/16 root directory.
In other words, the function expects the following input data:
1.1) FAT32 directory (which is cluster chain based);
OR
1.2) FAT12/16 non-root directory (which is also cluster chain based);
OR
1.3) FAT12/16 root directory (allocated as contiguous sectors area), but
all necessary information MUST be within the input buffer of filesystem cluster
size (thus cluster-chain jump is never initiated).
In order to accomplish the last condition, root directory parsing code in
do_fat_read() uses the following trick: read-out cluster-size block, process
only first sector (512 bytes), then shift 512 forward, read-out cluster-size
block and so on. This works great unless cluster size is equal to 512 bytes
(in a case you have a small partition), or long file name entries are scattered
across three sectors, see 4) for details.
2) Despite of the fact that get_vfatname() supports FAT32 root directory
browsing, do_fat_read() function doesn't send current cluster number correctly,
so root directory look-up doesn't work correctly.
3) get_vfatname() doesn't gather scattered entries correctly also is the case
when all LFN entries are located at the end of the source cluster, but real
directory entry (which must be returned) is at the only beginning of the
next one. No error detected, the resulting directory entry returned contains
a semi-random information (wrong size, wrong start cluster number and so on)
i.e. the entry is not accessible.
4) LFN (VFAT) allows up to 20 entries (slots) each containing 26 bytes (13
UTF-16 code units) to represent a single long file name i.e. up to 520 bytes.
U-Boot allocates 256 bytes buffer instead, i.e. 10 or more LFN slots record
may cause buffer overflow / memory corruption.
Also, it's worth to mention that 20+1 slots occupy 672 bytes space which may
take more than one cluster of 512 bytes (medium-size FAT32 or small FAT16
partition) - get_vfatname() function doesn't support such case as well.
The patch attached fixes these problems in the following way:
- keep using 256 bytes buffer for a long file name, but safely prevent a
possible buffer overflow (skip LFN processing, if it contains 10 or more
slots).
- explicitly specify FAT12/16 root directory parsing buffer size, instead
of relying on cluster size. The value used is a double sector size (to store
current sector and the next one). This fixes the first problem and increases
performance on big FAT12/16 partitions;
- send current cluster number (FAT32) to get_vfatname() during root
directory processing;
- use LFN counter to seek the real directory entry in get_vfatname() - fixes the
third problem;
- skip deleted entries in the root directory (to prevent bogus buffer
overflow detection and LFN counter steps).
Note: it's not advised to split up the patch, because a separate part may
operate incorrectly.
Daniel Hobi [Mon, 11 Oct 2010 16:03:35 +0000 (18:03 +0200)]
tools/imls: fix comment in Makefile
Commit d984fed0 (makefiles: fixes for building build tools)
changed the variable name FIT_CFLAGS to HOSTCFLAGS_NOPED
but forgot to update to corresponding comment.
Signed-off-by: Daniel Hobi <daniel.hobi@schmid-telecom.ch> Cc: Scott Wood <scottwood@freescale.com> Cc: Wolfgang Denk <wd@denx.de>
Stefan Roese [Wed, 8 Sep 2010 13:35:31 +0000 (15:35 +0200)]
zlib: Add further watchdog reset calls
Patch 253cb831 [zlib: add watchdog reset call] added already a few
watchdog reset calls to the new zlib U-Boot port. But on some boards
this is not enough. Additional calls are needed on boards with
short watchdog timeouts.
This was detected and tested on the lwmon5 board with a very short
watchdog timeout. Without this patch, the board resets during Linux
kernel decompression. With it, the decompression succeeds.
Stefan Roese [Wed, 8 Sep 2010 13:34:58 +0000 (15:34 +0200)]
zlib/gunzip: Use WATCHDOG_RESET macro
As usually done in U-Boot, the watchdog_reset code is called via a
macro (WATCHDOG_RESET). In zlib.c this was done differently, by using
a function pointer which is initialized with WATCHDOG_RESET upon watchdog
usage or with NULL otherwise. This patch now uses the plain
WATCHDOG_RESET macros to call the function resulting in slightly smaller
U-Boot images and simpler code.
U-Boot code size reduction:
PowerPC board with watchdog support (lwmon5):
-> 80 bytes smaller image size
PowerPC board without watchdog support (sequoia):
-> 112 bytes smaller image size
Signed-off-by: Stefan Roese <sr@denx.de> Cc: Detlev Zundel <dzu@denx.de> Cc: Wolfgang Denk <wd@denx.de> Acked-by: Detlev Zundel <dzu@denx.de>
fdt_support: support adding EDID property to FDT display nodes
Boards can pass display timing info for drivers using EDID
block. Provide common function to add board specific EDID
data to the device tree. Subsequent patch makes use of this
functionality.
Detailed timing descriptor data from EDID is used for
programming the display controller. This is currently
implemented on the Linux side by the fsl-diu-fb frame
buffer driver and it is documented there in
Documentation/powerpc/dts-bindings/fsl/diu.txt.
It is observed that, in most of the board configs the code is being
duplicated, also for any common change all board files needs update
This issue was under discussion from long on mailing list and we
converge on introducing common config file.
With this patch-
1. Total Kirkwood specific configuration code is reduced by 210 lines
2. All common configuration can be shared by multiple boards
3. Easy to manage common updates like ARM relocation changes
mv-common.h file is added to include/configs/
It contains all common configuration supported for all Kirkwood boards
The respective board configs are updated for its usage
Build tested for guruplug, mv88f6281gtw_ge, openrd_base,
rd6281a and sheevaplug
Binary execution tested for sheevaplug
Todo:
1. Other custom Kirkwood boards to be synced
2. The support to be extended for Orion5X based boards
For all Kirkwood boards so far dram_init function is duplicated
dram_init function is moved to dram.c and relevant code from all
board specific files removed
If any board needs specific dram init handling than standard one,
then, a macro CONFIG_SYS_BOARD_DRAM_INIT should be defined in
board config header file and the dram_init function can be put
in board specific source file
For ex. keymile boards
Kirkwood: print_cpuinfo fixed for valid devid revid
Earlier Device Identification register was used to detect
the type for SoC, considering 88F6282 support to be added,
It is not possible to detect the same using current
algorithm.
With this patch, device ID is being read using PCIE devid
register, also valid chip revision ID will also be read and
displayed
Albert Aribaud [Thu, 16 Sep 2010 15:00:30 +0000 (20:30 +0530)]
mvsata_ide: adjust port init sequence
mvsata_ide_initialize_port(): adjust init sequence (SStatus
should be checked only after all writes to SControl) and
return success/failure to ide_preinit().
Also, as some tests showed init durations in the hundreds
of us, raise the time-out to 01 ms to be on the safe side.
Signed-off-by: Albert Aribaud <albert.aribaud@free.fr>
projects / u-boot.git / log