Simon Holesch [Mon, 20 Nov 2023 00:08:34 +0000 (01:08 +0100)]
usb: ci: Fix gadget reinit
The ChipIdea device controller wasn't properly cleaned up when disabled.
So enabling it again left it in a broken state. The problem occurred for
example when the host unbinds the driver and binds it again.
During the first setup, when the out request is queued, the endpoint is
primed (`epprime`). If the endpoint is then disabled, it stayed primed
with the initial buffer. So after the endpoint is re-enabled, the device
controller and device driver were out of sync: the new out request was
in the driver queue head, yet not submitted, but the "complete" function
was still called, since the endpoint was primed with the old buffer.
With the fastboot function this error led to the (rather confusing)
error message "buffer overflow".
Fixed by clearing the primed buffers with the `epflush` (`ENDPTFLUSH`)
register.
Signed-off-by: Simon Holesch <simon@holesch.de> Reviewed-by: Marek Vasut <marex@denx.de> Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com> Link: https://lore.kernel.org/r/20231120002024.32865-1-simon@holesch.de Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
scsi: set dma direction to NONE for TEST UNIT READY
SCSI device scan code was executing TEST UNIT READY command without
explicitly setting dma direction in struct scsi_cmd to NONE, so command
was passed to driver with dma direction set to DMA_FROM_DEVICE,
inherited from older usage.
With WDC SDINDDH6-64G ufs device, that caused TEST UNIT READY to
return error.
Fix that, by explicitly setting dma direction to NONE for
TEST UNIT READY, and restoring it back DMA_FROM_DEVICE for the
following READ CAPACITY.
Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com> Reviewed-by: Marek Vasut <marex@denx.de>
Chris Packham [Fri, 27 Oct 2023 00:23:54 +0000 (13:23 +1300)]
Revert "arm64: Use FEAT_HAFDBS to track dirty pages when available"
This reverts commit 6cdf6b7a340db4ddd008516181de7e08e3f8c213. This is
part of a series trying to make use of the arm64 hardware features for
tracking dirty pages. Unfortunately this series causes problems for the
AC5/AC5X SoCs. Having exhausted other options the consensus seems to be
reverting this series is the best course of action.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Chris Packham [Fri, 27 Oct 2023 00:23:53 +0000 (13:23 +1300)]
Revert "arm64: Use level-2 for largest block mappings when FEAT_HAFDBS is present"
This reverts commit 836b8d4b205d2175b57cb9ef271e638b0c116e89. This is
part of a series trying to make use of the arm64 hardware features for
tracking dirty pages. Unfortunately this series causes problems for the
AC5/AC5X SoCs. Having exhausted other options the consensus seems to be
reverting this series is the best course of action.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Chris Packham [Fri, 27 Oct 2023 00:23:52 +0000 (13:23 +1300)]
Revert "armv8: enable HAFDBS for other ELx when FEAT_HAFDBS is present"
This reverts commit c1da6fdb5c239b432440721772d993e63cfdeb20. This is
part of a series trying to make use of the arm64 hardware features for
tracking dirty pages. Unfortunately this series causes problems for the
AC5/AC5X SoCs. Having exhausted other options the consensus seems to be
reverting this series is the best course of action.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Marcel Ziswiler [Thu, 26 Oct 2023 07:32:20 +0000 (09:32 +0200)]
imx: spl_imx_romapi: fix emmc fast boot mode case
This fixes a regression in the eMMC fast boot mode case where the buffer
was missing 464 bytes.
The code figures out how many bytes must at least be fetched to honor
the current read, rounds that up to the ss->pagesize [which is a no-op
in the USB download case because that has ->pagesize==1], fetches that
many bytes, but then recorded the original upper bound as the new end of
the valid data. However, this did not take into account the rounding up
to the ss->pagesize. Fix this by recording the actual bytes downloaded.
Fixes: 4b4472438f5a ("imx: spl_imx_romapi: avoid tricky use of spl_load_simple_fit() to get full FIT size") Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Acked-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk> Reviewed-by: Fabio Estevam <festevam@gmail.com>
John Keeping [Tue, 14 Nov 2023 11:30:17 +0000 (11:30 +0000)]
spl: fix TPL_SYS_MALLOC_F description
This config option enables the malloc() pool in TPL not the SPL. Fix
the description to accurately reflect this.
Fixes: fd8497dae54 (spl: Create proper symbols for enabling the malloc() pool) Signed-off-by: John Keeping <jkeeping@inmusicbrands.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Andre Przywara [Tue, 7 Nov 2023 16:09:00 +0000 (16:09 +0000)]
virtio: rng: gracefully handle 0 byte returns
According to the virtio v1.x "entropy device" specification, a virtio-rng
device is supposed to always return at least one byte of entropy.
However the virtio v0.9 spec does not mention such a requirement.
The Arm Fixed Virtual Platform (FVP) implementation of virtio-rng always
returns 8 bytes less of entropy than requested. If 8 bytes or less are
requested, it will return 0 bytes.
This behaviour makes U-Boot's virtio_rng_read() implementation go into an
endless loop, hanging the system.
Work around this problem by always requesting 8 bytes more than needed,
but only if a previous call to virtqueue_get_buf() returned 0 bytes.
This should never trigger on a v1.x spec compliant implementation, but
fixes the hang on the Arm FVP.
Signed-off-by: Andre Przywara <andre.przywara@arm.com> Reported-by: Peter Hoyes <peter.hoyes@arm.com>
Simon Glass [Thu, 16 Nov 2023 01:35:23 +0000 (18:35 -0700)]
bootstd: Avoid freeing a non-allocated buffer
EFI applications can be very large and thus used to cause boot failures
when malloc() space was exhausted.
A recent changed fixed this by using the kernel_addr_r environment var
as the address of the buffer. However, it still frees the buffer when
the bootflow is discarded.
Fix this by introducing a flag to indicate whether the buffer was
allocated, or not.
Note that kernel_addr_r is not the last word here. It might be better
to use lmb to place images. But there is a lot of refactoring to do
before we can remove the environment variables. The distro scripts rely
on them so it is safe for bootstd to do so too.
Fixes: 6a8c2f9781c bootstd: Avoid allocating memory for the EFI file Signed-off-by: Simon Glass <sjg@chromium.org>
Reported by: Simon Glass <sjg@chromium.org>
Reported by: Shantur Rathore <i@shantur.com> Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Tested-by: Shantur Rathore <i@shantur.com>
Simon Glass [Tue, 7 Nov 2023 09:17:40 +0000 (10:17 +0100)]
bootstage: Correct exhasuted typo
Correct this typo in the warning message shown when no more bootstage
records can be added.
Signed-off-by: Simon Glass <sjg@chromium.org> Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Sean Anderson [Sat, 4 Nov 2023 19:57:33 +0000 (15:57 -0400)]
sandbox: Close file after mmaping it
After opening pathname, we must close ifd once we are done with it.
Fixes: b9274095c2c ("sandbox: Add a way to map a file into memory") Signed-off-by: Sean Anderson <seanga2@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
CONFIG_DM_WARN has a text indicating that these messages should only
provided when debugging. This implies that the setting must be default no.
We should still create debug messages.
Reported-by: Andre Przywara <andre.przywara@arm.com> Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Simon Glass [Sat, 4 Nov 2023 16:25:24 +0000 (10:25 -0600)]
patman: Correct Python 3.6 behaviour
The importlib_resources import is not actually used. Fix this so that
patman can run on Python 3.6 to some extent, once
'pip3 install importlib-resources' has been run.
Simon Glass [Mon, 2 Oct 2023 01:14:37 +0000 (19:14 -0600)]
bootstd: Refactor mmc prep to allow a different scan
Adjust scan_mmc4_bootdev() and related function so that the caller can
do its own 'bootflow scan' command. This allows it to change the flags
if needed.
Simon Glass [Mon, 2 Oct 2023 01:14:36 +0000 (19:14 -0600)]
efi: Correct handling of frame buffer
The efi_gop driver uses private fields from the video uclass to obtain a
pointer to the frame buffer. Use the platform data instead.
Check the VIDEO_COPY setting to determine which frame buffer to use. Once
the next stage is running (and making use of U-Boot's EFI boot services)
U-Boot does not handle copying from priv->fb to the hardware framebuffer,
so we must allow EFI to write directly to the hardware framebuffer.
We could provide a function to read this, but it seems better to just
document how it works. The original change ignored an explicit comment
in the video.h file ("Things that are private to the uclass: don't use
these in the driver") which is why this was missed when the VIDEO_COPY
feature was added.
Signed-off-by: Simon Glass <sjg@chromium.org> Fixes: 8f661a5b662 ("efi_loader: gop: Expose fb when 32bpp") Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Marek Vasut [Sun, 5 Nov 2023 22:42:45 +0000 (23:42 +0100)]
mmc: renesas-sdhi: Disable clock after tuning reset when possible
Currently the renesas_sdhi_reset_tuning() unconditionally leaves SDHI
clock enabled after the tuning reset. This is not always necessary.
After the driver performed tuning reset at the end of probe function,
or in the unlikely case that tuning failed during regular operation,
the SDHI clock can be disabled after the tuning reset. The following
set_ios call would reconfigure the clock as needed.
In case of regular set_ios call which requires a tuning reset, keep
the clock enabled or disabled according to the mmc->clk_disable state.
With this in place, the controllers which have not been accessed via
block subsystem after boot are left in quiescent state. However, if an
MMC device is used e.g. for environment storage, that controller would
be accessed during the environment load and left active, including its
clock which would still be generated. This is due to the design of the
MMC subsystem, which does not deinit a controller after it was started
once, the controller is only deinited in case of mmc rescan, or before
OS boot.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org> Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com> Reviewed-by: Paul Barker <paul.barker.ct@bp.renesas.com> Tested-by: Paul Barker <paul.barker.ct@bp.renesas.com> Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Tested-by: Thuan Nguyen Hong <thuan.nguyen-hong@banvien.com.vn>
Tom Rini [Sun, 12 Nov 2023 21:36:22 +0000 (16:36 -0500)]
Merge branch 'master' of https://source.denx.de/u-boot/custodians/u-boot-sunxi
To quote Andre:
The first few patches are some easy refactorings and fixes, most of them
actually don't change the generated binaries at all. Then there is a
defconfig for a new board, for which we just gained the .dts file from
the last kernel DT sync.
On top there is support for a new PMIC (AXP313), and LPDDR4 support for
the Allwinner H616 SoC, both of which are needed to support new devices
that appeared lately, especially cheap TV boxes.
While those are technically new features, they don't affect existing
boards, for instance the LPDDR4 support code is guarded by a new DRAM
type Kconfig variable. So the risk for regressions is very slim.
Gitlab CI passed, and I booted that briefly on some boards, including an
H616 and an H618 one (with LPDDR4).
The H616 SoC family has support for several types of DRAM: DDR3,
LPDDR3, DDR4 and LPDDR4.
At the moment, the driver only supports DDR3 and LPDDR3 memory.
Let's extend the driver to support the LPDDR4 memory. This type
of memory widely used in device with T507(-H) SoC and new orangepi
zero3 with H618.
The compatibility with T507 is not yet complete, because there
is difference in the phy_init array.
The LPDDR4-2133 timings correspond to DRAM Rayson RS1G32LO4D2BDS-53BT
found on the NOR SPI from the Orangepi Zero 3 4GB.
Signed-off-by: Mikhail Kalashnikov <iuncuim@gmail.com> Tested-by: Piotr Oniszczuk <piotr.oniszczuk@gmail.com> Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com> Acked-by: Andre Przywara <andre.przywara@arm.com>
The original H616 DDR3 ODT configuration code wrote board specific values
into a sequence of paired registers.
For LPDDR3 support we needed to special-case one group of registers,
because for that DRAM type we need to write 0 into the lower register of
each pair. That already made the code less readable.
LPDDR4 support will make things even messier, so let's refactor that
code now: We allow to write different values into the lower and upper
half of each pair. The masking is moved into a macro, and use in each
write statement.
The effect is not as obvious yet, as we don't need the full flexibility at
the moment, but the motivation will become clearer with LPDDR4 support.
Andre Przywara [Sun, 30 Jul 2023 00:11:01 +0000 (01:11 +0100)]
power: pmic: sunxi: add AXP313 SPL driver
On boards using the AXP313 PMIC, the DRAM rail is often not setup
correctly at reset time, so we have to program the PMIC very early in
the SPL, before running the DRAM initialisation.
Add a simple AXP313 PMIC driver that knows about DCDC2(CPU) and
DCDC3(DRAM), so that we can bump up the voltage before the DRAM init.
Signed-off-by: Andre Przywara <andre.przywara@arm.com> Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Samuel Holland [Tue, 31 Oct 2023 04:57:40 +0000 (23:57 -0500)]
pinctrl: sunxi: Avoid using .bss for SPL
sunxi platforms put .bss in DRAM, so .bss is not available in SPL before
DRAM controller initialization. Therefore, this buffer must be placed in
the .data section.
Signed-off-by: Samuel Holland <samuel@sholland.org> Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Samuel Holland [Tue, 31 Oct 2023 05:22:35 +0000 (00:22 -0500)]
sunxi: mmc: Move header to the driver directory
The MMC controller driver is (and ought to be) the only user of these
register definitions. Put them in a header next to the driver to remove
the dependency on a specific ARM platform's headers.
Due to the sunxi_mmc_init() prototype, the file was not renamed. None of
the register definitions were changed.
Signed-off-by: Samuel Holland <samuel@sholland.org> Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Tom Rini [Mon, 17 Jul 2023 19:29:20 +0000 (15:29 -0400)]
arm: sunxi: Correct warning in board_fit_config_name_match
When building this with clang, we get a warning about having excess
parenthesis here, or that we're incorrectly using "==" when we want "=".
Correct these by using the common size macro.
Signed-off-by: Tom Rini <trini@konsulko.com> Reviewed-by: Simon Glass <sjg@chromium.org>
[Andre: Use SZ_512M as per Simon's suggestion] Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Andre Przywara [Sun, 27 Jun 2021 00:13:09 +0000 (01:13 +0100)]
sunxi: board: simplify early PMIC setup conditions
So far we have a convoluted #ifdef mesh that guards the early AXP PMIC
setup in board.c. That combination of &&, || and negations is very hard
to read, maintain and especially to extend.
Fortunately we have those same conditions already modelled in the
Kconfig file, so they are actually redundant. On top of that the real
reason we have those preprocessor guards in the first place is about the
symbols that are *conditionally* defined: without #ifdefs the build
would break because of them being undefined for many boards.
To simplify this, just change the guards to actually look at the symbols
needed, so CONFIG_AXP_xxx_VOLT instead of CONFIG_AXPyyy_POWER.
This drastically improves the readability of this code, and makes adding
PMIC support a pure Kconfig matter.
Doing this revealed one bug in Kconfig: there is no axp_set_dcdc4() for
the AXP818, even though CONFIG_AXP_DCDC4_VOLT includes that PMIC.
Since the AXP818 wasn't included when calling axp_set_dcdc4() in board.c,
this wasn't an issue, but becomes one now, so also remove the AXP818 from
the DCDC4 Kconfig symbol.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Milan P. Stanić [Sat, 4 Nov 2023 14:38:15 +0000 (15:38 +0100)]
doc: build: fix wrongly written targests instead of targets
Signed-off-by: Milan P. Stanić <mps@arvanta.net> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Nishanth Menon [Wed, 1 Nov 2023 14:50:25 +0000 (09:50 -0500)]
doc: ti: j7200_evm: Fix OPTEE platform name
k3-j7200 does not exist in upstream OPTEE. Use j721e as the platform
name. Using k3-j7200 as OPTEE name results in broken boot due to wrong
configuration being picked.
Dylan Corrales [Sat, 28 Oct 2023 09:46:39 +0000 (05:46 -0400)]
hikey960: Fix 404 links
The build instructions for the hikey960 had some broken links. Update
the links to use new vendor URLs. Also change build instructions to
reference a different file name.
Tom Rini [Fri, 10 Nov 2023 20:25:47 +0000 (15:25 -0500)]
Merge patch series "arm: dts: k3-am6: Fix Ethernet/DMA"
To quote the author:
Since commit [1], Ethernet is broken on TI AM62 and AM64 platforms.
The commit [1] is not the culprit. It just unearths the problem by fixing
the error check in k3-udma.c. This issue was silently being ignored earlier
due to wrong error check. [NULL instead of FDT_ADDR_T_NONE].
Fix the issue by adding the necessary register spaces for the u-boot K3-UDMA
driver for AM62 and AM64 platforms.
These properties will eventually make it into the SoC DTSi files [2] after
which these can be dropped from k3-*-u-boot.dtsi files.
[1] - 5fecea171de3dd ("treewide: use dev_read_addr_*_ptr() where appropriate")
[2] - https://lore.kernel.org/linux-arm-kernel/20230810174356.3322583-1-vigneshr@ti.com/
Update main_bcdma and main_pktdma nodes for native configuration in the
absence of DM services. u-boot k3-udma driver expects these additional
register fields else probe will fail.
Tom Rini [Fri, 10 Nov 2023 14:43:01 +0000 (09:43 -0500)]
Merge tag 'u-boot-stm32-20231110' of https://source.denx.de/u-boot/custodians/u-boot-stm
_ Fix compilation issue when SYS_DCACHE_OFF and/or SYS_DCACHE_SYS are enabled
_ Fix issue following DT sync with kernel 6.3 for stm32mp15xx-ev1 and DHSOM SoM
_ Enable TCP, IPv6, wget on DH STM32MP15 DHSOM
_ Limit u-boot.itb size to 0x160000 bytes on DH STM32MP15 DHSOM
_ Read auth stats and boot_partition from tamp
Tom Rini [Fri, 10 Nov 2023 13:44:18 +0000 (08:44 -0500)]
Merge branch '2023-11-10-assorted-fixes'
- Fix some issues Coverity has reported, update MAINTAINERS file,
another bootstd fix, typo fix in error message, gitignore fix and
update TI's URL in many places.
Sam Protsenko [Thu, 26 Oct 2023 21:00:15 +0000 (16:00 -0500)]
tools: gitignore: Fix tools/generated path
'git status' shows 'tools/generated/' after running the build, which is
wrong. The corresponding .gitignore rule was already added in commit c623642d29be ("Adjust gitignore for tools/generated/"), but because of
superfluous 'tools/' part it wasn't in effect. Remove incorrect 'tools/'
part to fix it.
While at it, remove tools/ path incorrectly added to the top-level
.gitignore in commit 801c482207c7 (".gitignore: ignore misc include,
simple-bin, and tools/generated build artifacts"), as it's required in
the comment on the top of .gitignore:
# NOTE! Don't add files that are generated in specific
# subdirectories here. Add them in the ".gitignore" file
# in that subdirectory instead.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org> Fixes: c623642d29be ("Adjust gitignore for tools/generated/") Fixes: 801c482207c7 (".gitignore: ignore misc include, simple-bin, and tools/generated build artifacts")
Tony Dinh [Thu, 2 Nov 2023 18:51:15 +0000 (11:51 -0700)]
bootstd: Skip over bad device during bootflows scanning
During bootstd scanning for bootdevs, if bootdev_hunt_drv() encounters
a device not found error (e.g. ENOENT), let it return a successful status
so that bootstd will continue scanning the next devices, not stopping
prematurely.
Background:
During scanning for bootflows, it's possible for bootstd to encounter a
faulty device controller. Also when the same u-boot is used for another
variant of the same board, some device controller such as SATA might
not exist.
I've found this issue while converting the Marvell Sheevaplug board to
use bootstd. This board has 2 variants, the original Sheevaplug has MMC and
USB only, but the later variant comes with USB, MMC, and eSATA ports. We
have been using the same u-boot (starting with CONFIG_IDE and later with DM
CONFIG_SATA) for both variants. This worked well with the old
envs-scripting booting scheme.
Signed-off-by: Tony Dinh <mibodhi@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Tom Rini [Wed, 8 Nov 2023 19:28:11 +0000 (14:28 -0500)]
scsi: Have scsi_init_dev_desc_priv() use memset
When we do not have CONFIG_BOUNCE_BUFFER enabled, inside of
scsi_init_dev_desc_priv we never set the 'bb' field to false, we only
initialize it to true when CONFIG_BOUNCE_BUFFER is set. Given that we
have a number of other fields here we had been explicitly setting to
zero, change to first calling memset to clear the struct and then
initialize only the fields that need non-zero default values.
Addresses-Coverity-ID: 467407 ("Uninitialized variables (UNINIT)") Fixes: 81bd22e935dc ("rockchip: block: blk-uclass: add bounce buffer flag to blk_desc") Signed-off-by: Tom Rini <trini@konsulko.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Keep track of the re-entries with help of the lr register.
This binary can be re-used and called from various BROM functions.
Only when it's called from the part that handles SPI, NAND or EMMC
hardware it needs to early return to BROM ones.
In download mode when it handles data on USB OTG and UART0
this section must be skipped.
Unlike newer Rockchip SoC models the rk3066 BROM code does not have built-in
support to enter download mode on return to BROM. This binary must check
the boot mode register for the BOOT_BROM_DOWNLOAD flag and reset if it's set.
It then returns to BROM to the end of the function that reads boot blocks.
From there the BROM code goes into a download mode and waits for data
on USB OTG and UART0.
Signed-off-by: Johan Jonker <jbx6244@gmail.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Quentin Schulz [Fri, 3 Nov 2023 09:28:13 +0000 (10:28 +0100)]
rockchip: ringneck-px30: enable SPL_BOARD_INIT
Now that Ringneck requires some board-specific code (namely resetting
the MCU companion controller) to be run during SPL stage, let's enable
SPL_BOARD_INIT.
Quentin Schulz [Fri, 3 Nov 2023 09:28:12 +0000 (10:28 +0100)]
rockchip: ringneck-px30: always reset STM32 companion controller on boot
It's happened that glitches on the STM32_RST and STM32_BOOT lines have
put the STM32 companion microcontroller into DFU mode making it not boot
its FW, rendering it useless for the user.
Considering that the STM32 companion microcontroller is always reset on
a reboot or power cycle, resetting it once again in U-Boot SPL isn't
going to hurt it any more.
For ATtiny companion microcontroller, the situation is a bit different
because a reboot or power cycle doesn't reset it. Additionally, since it
can only be reset with a UPDI reset on the STM32_RST line, and that is
virtually impossible to mistakenly trigger, the ATtiny is unlikely to be
in unwanted reset or enter reset because U-Boot toggles STM32_RST line.
Tim Lunn [Mon, 30 Oct 2023 13:12:41 +0000 (00:12 +1100)]
rockchip: dts: fix bootph tags for rv1126
RV1126 fails to boot on 2024.01-rc1.
Commit 9e644284ab81 ("dm: core: Report bootph-pre-ram/sram node as
pre-reloc after relocation") changed the behaviour of bootph-pre-ram, to
limit nodes to spl phase. This caused rv1126 boards to fail to boot with
the current dts.
This patch updates the pmu/grf nodes to bootph-all tags as they are
needed in all phases. This fixes the boot issue on rv1126 boards.
Signed-off-by: Tim Lunn <tim@feathertop.org> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Igor Opaniuk [Mon, 6 Nov 2023 10:41:52 +0000 (11:41 +0100)]
stm32mp1: read auth stats and boot_partition from tamp
Obtain from TAMP backup register information about image authorization
status and partition id used for booting. Store this info in
environmental variables ("boot_auth" and "boot_part" correspondingly).
Image authorization supported values:
0x0 - No authentication done
0x1 - Authentication done and failed
0x2 - Authentication done and succeeded
These values are stored to TAMP backup register by Trusted Firmware-A [1].
Marek Vasut [Sat, 4 Nov 2023 16:31:57 +0000 (17:31 +0100)]
arm: stm32: Limit u-boot.itb size to 0x160000 bytes on DH STM32MP15 DHSOM
The maximum size of u-boot.itb in SPI NOR on DH STM32MP15 DHSOM is
0x160000 . Define this size in U-Boot config to prevent misconfigured
builds from emitting larger u-boot.itb than the one which fits the
SPI NOR area reserved for the blob.
The SPI NOR layout is as follows:
0x00_0000..0x03_ffff ... SPL 1
0x04_0000..0x07_ffff ... SPL 2
0x08_0000..0x1d_ffff ... U-Boot
0x1e_0000..0x1e_ffff ... Environment 1
0x1f_0000..0x1f_ffff ... Environment 2
Signed-off-by: Marek Vasut <marex@denx.de> Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Marek Vasut [Sat, 4 Nov 2023 16:31:56 +0000 (17:31 +0100)]
arm: stm32: Enable TCP, IPv6, wget on DH STM32MP15 DHSOM
Enable support for TCP protocol, wget, and IPv6 on this platform.
The former two allow users download payload into the U-Boot from
a web server, which may be more convenient or easier to set up
than TFTP server. The later is enabled to future proof the IP
stack on this platform.
Signed-off-by: Marek Vasut <marex@denx.de> Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Marek Vasut [Mon, 9 Oct 2023 23:15:51 +0000 (01:15 +0200)]
ARM: dts: stm32mp: Repair damage from alignment with v6.3
The patch fixed by this commit renders ST STM32MP15xx EV1 board and
all DHSOM SoM based boards unbootable from SPI NOR. Fix the damage
by updating -u-boot.dtsi to match the stm32mp15-pinctrl.dtsi update.
Fixes: 08002ffd083d ("ARM: dts: stm32mp: alignment with v6.3") Signed-off-by: Marek Vasut <marex@denx.de> Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Bhupesh Sharma [Tue, 22 Aug 2023 07:51:11 +0000 (13:21 +0530)]
arm: stm32mp: Really fix compilation issue when SYS_DCACHE_OFF and/or SYS_DCACHE_SYS are enabled
While 23e20b2fa6 ("arm: stm32mp: Fix compilation issue when
SYS_DCACHE_OFF and/or SYS_DCACHE_SYS are enabled") tried fixing
this issue, fix it really by adding #if checks for SYS_ICACHE_OFF
and SYS_DCACHE_OFF.
Cc: Patrice Chotard <patrice.chotard@foss.st.com> Cc: Patrick Delaunay <patrick.delaunay@foss.st.com> Signed-off-by: Bhupesh Sharma <bhupesh.sharma@linaro.org> Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com> Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
QuartzPro64 is a Rockchip RK3588 based SBC by Pine64.
UART and boot over SD/eMMC/RJ45 are tested to work.
Linux commits from next-20231013: 8152d3d070a9 ("arm64: dts: rockchip: Add QuartzPro64 SBC device tree")
Signed-off-by: Tom Fitzhenry <tom@tom-fitzhenry.me.uk> Reviewed-by: Kever Yang <kever.yang@rock-chips.com> Cc: Eugen Hristev <eugen.hristev@collabora.com> Cc: Jonas Karlman <jonas@kwiboo.se> Cc: Ondrej Jirman <megi@xff.cz>
Michal Simek [Wed, 1 Nov 2023 12:06:15 +0000 (13:06 +0100)]
arm64: zynqmp: Add description for nvmem efuse layout
Based on discussion with DT folks at link below there is not going to be
any name restrictions for child names. That's why add description for
current nvmem layout.
Michal Simek [Wed, 1 Nov 2023 11:22:14 +0000 (12:22 +0100)]
ARM: zynq: Add partition description
Xilinx is using standard mtd partition layout for quite a long time. It is
used for testing purpose on evaluation boards.
Also #address/size-cells shouldn't be present without nodes which should
use them that's why move them from zynq-7000.dtsi to nand/nor nodes
directly.
The patch was tested on zc706 and zedboard(with also increasing max
frequency and rx bus width).
Michal Simek [Wed, 1 Nov 2023 08:01:03 +0000 (09:01 +0100)]
arm64: zynqmp: Comment all smmu entries
SMMU is disabled by default and not all masters can be enabled at the same
time because of limited number of entries. That's why comment all iommu
properties but keep them for reference in DT. In XEN case they should be
added back and Xen should have SMMU enabled by default.
Also add IDs for DP and DPDMA.
Michal Simek [Thu, 26 Oct 2023 14:04:52 +0000 (16:04 +0200)]
arm64: versal-net: Add DTSes for mini qspi/ospi configuration
Mini U-Boot is running out of OCM and it's only purpose is to program non
volatile memories. There are different configurations which ospi/qspi can
be that's why describe them via DT.
DT binding is already approved that's why there is no reason not to add it.
Michal Simek [Thu, 26 Oct 2023 14:04:51 +0000 (16:04 +0200)]
arm64: versal: Add DTSes for mini qspi/ospi configuration
Mini U-Boot is running out of OCM and it's only purpose is to program non
volatile memories. There are different configurations which ospi/qspi can
be that's why describe them via DT.
DT binding is already approved that's why there is no reason not to add it.
Michal Simek [Thu, 26 Oct 2023 14:04:50 +0000 (16:04 +0200)]
ARM: zynq: Add DTSes for mini qspi configurations
Mini U-Boot is running out of OCM and it's only purpose is to program non
volatile memories. There are different configurations which qspi can be
that's why describe them via DT.
DT binding is already approved that's why there is no reason not to add it.
Michal Simek [Thu, 26 Oct 2023 14:04:49 +0000 (16:04 +0200)]
ARM: zynq: Add DTSes for mini qspi configurations
Mini U-Boot is running out of OCM and it's only purpose is to program non
volatile memories. There are different configurations which qspi can be
that's why describe them via DT.
DT binding is already approved that's why there is no reason not to add it.
The Standard Host Controller Interface (SDHCI) specification version
3.00 adds support for Advanced DMA (ADMA) for both 64 and 32 bit
widths of DMA. This significantly improves read and write throughput.
Tejas Bhumkar [Fri, 20 Oct 2023 05:06:22 +0000 (10:36 +0530)]
arm64: zynqmp: Disable Tri-state for MIO38 Pin
gpio38 is used in SOM's kv260 to reset the Ethernet PHY.
At present, HW reset is not working properly as Tri-state
is enabled for MIO38, causing inappropriate PHY register reads.
Disabled Tri-state for MIO38 to make HW reset work.
arm64: dts: zynqmp: make hw-ecc as the default ecc mode
Except for Linux no other component (i.e., u-boot, fsbl or BootRom) of the
software stack supports software ecc engine. So, make hw-ecc as the default
ecc mode.
projects / u-boot.git / log