Tim Harvey [Wed, 30 Jun 2021 23:50:03 +0000 (16:50 -0700)]
net: fec: use device sequence vs index when fetching fec
When using uclass_get_device* to get the FEC device we need to use
device sequence instead of index into UCLASS_ETH. In systems where for
example a I2C based DSA switch exists it will probe before the FEC
master and its ports will be registered first and have the first
indexes yet the FEC's sequence comes from the device-tree alias.
Take for example the imx8mm-venice-gw7901 board which has an i2c based
DSA switch:
u-boot=> net list
eth1 : lan1 00:0d:8d:aa:00:2f
eth2 : lan2 00:0d:8d:aa:00:30
eth3 : lan3 00:0d:8d:aa:00:31
eth4 : lan4 00:0d:8d:aa:00:32
eth0 : ethernet@30be0000 00:0d:8d:aa:00:2e active
Thus in this case uclass_get_device(UCLASS_ETH, 0, &dev) returns lan1
which is wrong but uclass_get_device_seq(UCLASS_ETH, 0, &dev) returns
ethernet@30be000 which is correct.
Signed-off-by: Tim Harvey <tharvey@gateworks.com> Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Tim Harvey [Wed, 30 Jun 2021 23:50:02 +0000 (16:50 -0700)]
board: gateworks: venice: add imx8mm-gw7901 support
The Gateworks GW7901 is an ARM based single board computer (SBC)
featuring:
- i.MX8M Mini SoC
- LPDDR4 DRAM
- eMMC FLASH
- SPI FRAM
- Gateworks System Controller (GSC)
- Atmel ATECC Crypto Authentication
- USB 2.0
- Microchip GbE Switch
- Multiple multi-protocol RS232/RS485/RS422 Serial ports
- onboard 802.11ac WiFi / BT
- microSD socket
- miniPCIe socket with PCIe, USB 2.0 and dual SIM sockets
- Wide range DC power input
- 802.3at PoE
To add support for this board:
- add dts from Linux (accepted for v5.14)
- add SPL PMIC config
With the first redesign the debug UART had changed from
UART2 to UART1.
As the first hardware revision is considered as alpha and
will not be supported in future. The old setup will not
be preserved.
Tim Harvey [Tue, 6 Jul 2021 17:19:09 +0000 (10:19 -0700)]
pci: imx: use reset-gpios if defined by device-tree
If reset-gpio is defined by device-tree use that if
CONFIG_PCIE_IMX_PERST_GPIO is not defined.
Note that after this the following boards which define
CONFIG_PCIE_IMX_PERST_GPIO in their board header file as well as their
device-tree should be able to remove CONFIG_PCIE_IMX_PERST_GPIO without
consequence:
- mx6sabresd
- mx6sxsabresd
- novena
- tbs2910
- vining_2000
Note that the ge_bx50v3 board uses CONFIG_PCIE_IMX_PERST_GPIO and does
not have reset-gpios defined it it's pcie node in the dt thus removing
CONFIG_PCIE_IMX_PERST_GPIO globally can't be done until that board adds
reset-gpios.
Cc: Ian Ray <ian.ray@ge.com> (maintainer:GE BX50V3 BOARD) Cc: Sebastian Reichel <sebastian.reichel@collabora.com> (maintainer:GE BX50V3 BOARD) Cc: Fabio Estevam <festevam@gmail.com> (maintainer:MX6SABRESD BOARD) Cc: Marek Vasut <marex@denx.de> (maintainer:NOVENA BOARD) Cc: Soeren Moch <smoch@web.de> (maintainer:TBS2910 BOARD) Cc: Silvio Fricke <open-source@softing.de> (maintainer:VINING_2000 BOARD) Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Tim Harvey [Fri, 11 Jun 2021 19:46:24 +0000 (12:46 -0700)]
imx: ventana: put LTC3676 regulators in continuous mode
In the default pulse-skipping mode regulators that are very lightly
loaded can fail to regulate properly. Switching them to always use
continuous mode causes only around 10mW of overall system power
difference in a lightly loaded system that isn't already operating
them in continuous mode.
Tim Harvey [Fri, 11 Jun 2021 19:46:23 +0000 (12:46 -0700)]
imx: ventana: put PFUZ100 regulators in continuous mode
In the default 'auto' mode regulators that are very lightly loaded
can be put in PFM mode and fail to regulator properly. Switching them
to always use continuous PWM mode has a neglibable affect on system
power and garuntees proper regulation under lightly loaded circumstances.
Tim Harvey [Fri, 11 Jun 2021 19:46:22 +0000 (12:46 -0700)]
imx: ventana: add PMIC fix for GW54xx-G
Substitutions in EOL parts changes the VDD_2P5 voltage rail such that
the previously unused VGEN6 LDO is needed in place of the lower power
VGEN5 for the GW54xx-G.
Tim Harvey [Fri, 11 Jun 2021 19:46:18 +0000 (12:46 -0700)]
imx: ventana: remove USB_KEYBOARD support
For some time now having USB_KEYBOARD support has caused usb to be
initialized on boot. To allow for a quicker bootup we don't want this
for Ventana and don't really need USB keyboard support so remove it.
imx8m: Restrict usable memory to space below 4G boundary
Some IPs have their accessible address space restricted by the
interconnect. Let's make sure U-Boot only ever uses the space below
the 4G address boundary (which is 3GiB big), even when the effective
available memory is bigger.
We implement board_get_usable_ram_top() for all i.MX8M SoCs, as the
whole family is affected by this.
Marek Vasut [Sat, 29 May 2021 11:34:32 +0000 (13:34 +0200)]
arm: bootm: Disable LMB reservation for command line and board info on arm64
On arm64, board info is not applicable and kernel command line patched into
the DT, so the LMB reservation here makes no sense anymore. On legacy arm32,
this might still be necessary on systems which do not use DT or use legacy
ATAGS. Disable this LMB reservation on arm64.
This also permits Linux DT to specify reserved memory node at address close
to the end of DRAM bank, i.e. overlaping with U-Boot location. Since after
boot, U-Boot will be no more, this is OK.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Hai Pham <hai.pham.ud@renesas.com> Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com> Cc: Stephen Warren <swarren@nvidia.com> Cc: Tom Rini <trini@konsulko.com>
Mark Kettenis [Wed, 10 Feb 2021 19:14:55 +0000 (20:14 +0100)]
armv8: Handle EL2 Host mode
On implementations that support VHE, the layout of the CPTR_EL2
register depends on whether HCR_EL2.E2H is set. If the bit is
set, CPTR_EL2 uses the same layout as CPACR_EL1 and can in fact
be accessed through that register. In that case, jump to the
EL1 code to enable access to the FP/SIMD registers. This allows
U-Boot to run on systems that pass control to U-Boot in EL2 with
EL2 Host mode enabled such as machines using Apple's M1 SoC.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org> Acked-by: Marc Zyngier <maz@kernel.org>
Tim Harvey [Thu, 17 Jun 2021 23:31:07 +0000 (16:31 -0700)]
octeontx: do not require cavium BDK node to be present
The cavium,bdk node is a non-standard dt node used by the BDK and
therefore it is removed from the dt before booting Linux. Do not
require this node to exist as it won't for standard dt's.
Signed-off-by: Tim Harvey <tharvey@gateworks.com> Reviewed-by: Stefan Roese <sr@denx.de>
Pali Rohár [Tue, 25 May 2021 17:42:42 +0000 (19:42 +0200)]
arm: mvebu: a37xx: Enable more baudrates
Extend CONFIG_SYS_BAUDRATE_TABLE and include all standard baudrates and
also nonstandard up to the 6 MBaud. U-Boot's A3720 UART driver can use
baudrates from 300 Baud to 6 MBaud.
This changes all A3720 boards, since all of them include either
mvebu_armada-37xx.h or turris_mox.h config file.
Signed-off-by: Pali Rohár <pali@kernel.org> Reviewed-by: Marek Behún <marek.behun@nic.cz> Reviewed-by: Stefan Roese <sr@denx.de>
Pali Rohár [Tue, 25 May 2021 17:42:41 +0000 (19:42 +0200)]
serial: a37xx: Switch to XTAL clock when booting Linux kernel
Unfortunately the UART driver in current Linux for Armada 3700 expects
UART's parent clock to be XTAL and calculats baudrate divisor according
to XTAL clock. Therefore we must switch back to XTAL clock before
booting kernel.
Implement .remove method for this driver with DM_FLAG_OS_PREPARE flag
set.
If current baudrate is unsuitable for XTAL clock then we do not change
anything. This can only happen if the user either configured unsupported
settings or knows what they are doing and has kernel patches which allow
usage of non-XTAL parent clock.
Signed-off-by: Pali Rohár <pali@kernel.org> Reviewed-by: Marek Behún <marek.behun@nic.cz> Reviewed-by: Stefan Roese <sr@denx.de>
Pali Rohár [Tue, 25 May 2021 17:42:40 +0000 (19:42 +0200)]
serial: a37xx: Use TBG as parent clock
Using TBG clock as parent clock for UART allows us using higher
baudrates than 230400.
Turris MOX with external FT232RL USB-UART works fine up to 3 MBaud
(which is maximum for this USB-UART controller), while EspressoBIN with
integrated pl2303 USB-UART also works fine up to 6 MBaud.
Slower baudrates with TBG as a parent clock can be achieved by
increasing TBG dividers and oversampling divider. When using the slowest
TBG clock, minimal working baudrate is 300.
Signed-off-by: Pali Rohár <pali@kernel.org> Signed-off-by: Marek Behún <marek.behun@nic.cz> Reviewed-by: Stefan Roese <sr@denx.de>
Marek Behún [Tue, 25 May 2021 17:42:39 +0000 (19:42 +0200)]
clk: armada-37xx: Set DM_FLAG_PRE_RELOC
Setting DM_FLAG_PRE_RELOC for Armada 3720 clock drivers (TBG and
peripheral clocks) makes it possible for serial driver to retrieve clock
rates via clk API.
Signed-off-by: Marek Behún <marek.behun@nic.cz> Reviewed-by: Stefan Roese <sr@denx.de>
Pali Rohár [Tue, 25 May 2021 17:42:38 +0000 (19:42 +0200)]
serial: a37xx: Fix parent clock rate value and divider calculation
UART parent clock is by default the platform's xtal clock, which is
25 MHz.
The value defined in the driver, though, is 25.8048 MHz. This is a hack
for the suboptimal divisor calculation
Divisor = UART clock / (16 * baudrate)
which does not use rounding division, resulting in a suboptimal value
for divisor if the correct parent clock rate was used.
Change the code for divisor calculation to round to closest value, i.e.
Divisor = Round(UART clock / (16 * baudrate))
and change the parent clock rate value to that returned by
get_ref_clk().
This makes A3720 UART stable at standard UART baudrates between 1800 and
230400.
Signed-off-by: Pali Rohár <pali@kernel.org> Reviewed-by: Marek Behún <marek.behun@nic.cz> Reviewed-by: Stefan Roese <sr@denx.de>
- Remove a large number of platforms that did not migrate to DM_PCI or
DM_USB by 2 years past the migration deadline and do not have a
migration imminent.
Tom Rini [Sat, 22 May 2021 12:47:14 +0000 (08:47 -0400)]
arm: Remove spear600 boards and the rest of SPEAr support
These boards have not been converted to CONFIG_DM_USB by the deadline
and is also missing conversion to CONFIG_DM. Remove them. As this is
the last of the SPEAr platforms, so remove the rest of the remaining
support as well.
Cc: Vipin Kumar <vipin.kumar@st.com> Signed-off-by: Tom Rini <trini@konsulko.com>
Tom Rini [Sat, 22 May 2021 12:47:13 +0000 (08:47 -0400)]
arm: Remove spear320 boards
These boards have not been converted to CONFIG_DM_USB by the deadline
and is also missing conversion to CONFIG_DM. Remove them. As this is
also the last SPEAR3XX platform, remove that symbol as well.
Cc: Vipin Kumar <vipin.kumar@st.com> Signed-off-by: Tom Rini <trini@konsulko.com>
Tom Rini [Sat, 22 May 2021 12:47:06 +0000 (08:47 -0400)]
mx6memcal: Disable USB GADGET in SPL
As this board does not use CONFIG_OF_CONTROL and the DM_USB migration
deadline has passed, disable USB_GADGET support.
Cc: Eric Nelson <eric@nelint.com> Cc: Stefano Babic <sbabic@denx.de> Signed-off-by: Tom Rini <trini@konsulko.com> Acked-by: Eric Nelson <eric@nelint.com>
Tom Rini [Sun, 23 May 2021 14:58:05 +0000 (10:58 -0400)]
ppc: Remove T4160RDB board
This board has not been converted to CONFIG_DM_PCI by the deadline and is
also missing conversion to CONFIG_DM. Remove it. As this is the last
ARCH_T4160 platform, remove that support as well.
Tom Rini [Sat, 15 May 2021 01:34:27 +0000 (21:34 -0400)]
ppc: Remove MPC8315ERDB board
This board has not been converted to CONFIG_DM_PCI by the deadline and is
also missing conversion to CONFIG_DM. Remove it. As this is the last
ARCH_MPC8315 platform, remove that support as well.
Tom Rini [Sat, 15 May 2021 01:34:26 +0000 (21:34 -0400)]
ppc: Remove sbc8641d board
This board has not been converted to CONFIG_DM_PCI by the deadline and is
also missing conversion to CONFIG_DM. Remove it. This is also the last
of the ARCH_MPC8641/MPC8610 platforms, so remove that support as well.
Cc: Paul Gortmaker <paul.gortmaker@windriver.com> Cc: Priyanka Jain <priyanka.jain@nxp.com> Signed-off-by: Tom Rini <trini@konsulko.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Tom Rini [Sat, 15 May 2021 01:34:25 +0000 (21:34 -0400)]
ppc: Remove xpedite boards
These boards have not been converted to CONFIG_DM_PCI by the deadline and is
also missing conversion to CONFIG_DM. Remove them. As this includes
the last ARCH_MPC8572 platform, remove that as well.
Cc: Peter Tyser <ptyser@xes-inc.com> Signed-off-by: Tom Rini <trini@konsulko.com> Acked-by: Peter Tyser <ptyser@xes-inc.com>
Tom Rini [Sat, 15 May 2021 01:34:23 +0000 (21:34 -0400)]
ppc: Remove MPC8568MDS board
This board has not been converted to CONFIG_DM_PCI by the deadline and is
also missing conversion to CONFIG_DM. Remove it. As this is the last
ARCH_MPC8568 platform, remove that support as well.
Cc: Priyanka Jain <priyanka.jain@nxp.com> Signed-off-by: Tom Rini <trini@konsulko.com>
Tom Rini [Sat, 15 May 2021 01:34:22 +0000 (21:34 -0400)]
ppc: Remove T1023RBD boards and T1024RDB_SECURE_BOOT
These boards have not been converted to CONFIG_DM_PCI by the deadline
and is also missing conversion to CONFIG_DM. Remove them. As this is
the only ARCH_T1023 platform left, remove that support as well.
Cc: Priyanka Jain <priyanka.jain@nxp.com> Signed-off-by: Tom Rini <trini@konsulko.com>
Tom Rini [Sat, 15 May 2021 01:34:21 +0000 (21:34 -0400)]
ppc: Remove MPC8555CDS boards
These boards have not been converted to CONFIG_DM_PCI by the deadline and is
also missing conversion to CONFIG_DM. Remove them. As this is the only
ARCH_MPC8555 platform left, remove that support as well.
Cc: Priyanka Jain <priyanka.jain@nxp.com> Signed-off-by: Tom Rini <trini@konsulko.com>
Tom Rini [Sat, 15 May 2021 01:34:20 +0000 (21:34 -0400)]
ppc: Remove MPC8541CDS board
This board has not been converted to CONFIG_DM_PCI by the deadline and is
also missing conversion to CONFIG_DM. Remove it. As this is the only
MPC8541 target left, remove that architecture support as well.
Cc: Priyanka Jain <priyanka.jain@nxp.com> Signed-off-by: Tom Rini <trini@konsulko.com>
Tom Rini [Sat, 15 May 2021 01:34:10 +0000 (21:34 -0400)]
m68k: Remove M5475x boards
These board has not been converted to CONFIG_DM_PCI by the deadline.
Remove them. As this is the last of the mcf547x_8x family of boards,
remove that support as well.
Cc: TsiChung Liew <Tsi-Chung.Liew@nxp.com> Signed-off-by: Tom Rini <trini@konsulko.com>
Tom Rini [Sat, 15 May 2021 01:34:09 +0000 (21:34 -0400)]
m68k: Remove M5485 boards
These board has not been converted to CONFIG_DM_PCI by the deadline.
Remove them. As this is all of the CONFIG_M548x platforms as well,
remove that code.
Cc: TsiChung Liew <Tsi-Chung.Liew@nxp.com> Signed-off-by: Tom Rini <trini@konsulko.com>
Tom Rini [Fri, 2 Jul 2021 14:41:58 +0000 (10:41 -0400)]
Azure/GitLab: Move to gcc-11.1.0 and LLVM-11
- Move to gcc-11.1.0 builds from kernel.org for supported platforms and
LLVM-11 for those tests.
- As Heinrich has noted, the RISC-V platform specification has a profile
OS-A for running rich operating systems like Linux and BSD. This profile
requires 64bit and UEFI conforming to the EBBR. Only the 'embedded'
profile may use 32bit. Given this, drop grub for 32bit RISC-V as it no
longer compiles with gcc-11.1 and upstream is unlikely to fix it:
https://www.mail-archive.com/grub-devel@gnu.org/msg30736.html
- Update to grub-2.06 release to address other issues of building with
gcc-11.1.
- Update to newer Xtensa (gcc-9.2.0) and ARC (gcc-10.2) toolchains
Cc: Heinrich Schuchardt <xypron.glpk@gmx.de> Cc: Bin Meng <bmeng.cn@gmail.com> Cc: Simon Glass <sjg@chromium.org> Cc: Rick Chen <rick@andestech.com> Signed-off-by: Tom Rini <trini@konsulko.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Bin Meng [Wed, 7 Jul 2021 07:36:26 +0000 (15:36 +0800)]
x86: Drop _X86EMU_env definition when CONFIG_BIOSEMU is used
With x86 we can execute an option ROM either natively or using the
x86 emulator (if enabled with CONFIG_BIOSEMU). Both of these share
the _X86EMU_env variable, with the native code using it to hold
register state during interrupt processing.
At present, in 32-bit U-Boot, the variable is declared twice, once
in common code and once in code only compiled with CONFIG_BIOSEMU.
With GCC 11 this causes a 'multiple definitions' error on boards
with CONFIG_BIOSEMU.
Drop the emulator definition when CONFIG_BIOSEMU is used.
Tom Rini [Mon, 3 May 2021 20:48:58 +0000 (16:48 -0400)]
bootstage: Eliminate when not enabled
When we do not have bootstage enabled, rather than include an empty
dummy function, we just don't reference it. This saves us space in some
tight builds. This also shows a few cases where show_boot_progress was
incorrectly guarded before.
Cc: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Rini <trini@konsulko.com>
Tom Rini [Mon, 3 May 2021 20:48:55 +0000 (16:48 -0400)]
eb_cpu5282: Declare diplay_width / display_height as externs
The board code here references the display_width / display_height
variables set in the video driver, declare these as externs as gcc-11
will notice and lead to a multiple definition error.
Tom Rini [Mon, 3 May 2021 20:48:54 +0000 (16:48 -0400)]
freescale: Drop unnecessary cpld_data_t non-typedef
In some board cpld.h files the definition of the cpld_data struct
not-quite makes a typedef for cpld_data_t. This problem is caught with
gcc-11 as a multiple definition error. As there are no users of this
non-typedef, fix this by not declaring it one to begin with.
Cc: Priyanka Jain <priyanka.jain@nxp.com> Cc: Shengzhou Liu <Shengzhou.Liu@nxp.com> Signed-off-by: Tom Rini <trini@konsulko.com>
With gcc-11 we see:
drivers/ddr/marvell/a38x/ddr3_debug.c:672:47: error: argument 2 of type 'u32[5]' {aka 'unsigned int[5]'} with mismatched bound [-Werror=array-parameter=]
672 | int ddr3_tip_read_adll_value(u32 dev_num, u32 pup_values[MAX_INTERFACE_NUM * MAX_BUS_NUM],
| ~~~~^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
In file included from drivers/ddr/marvell/a38x/ddr3_training_ip_engine.h:10,
from drivers/ddr/marvell/a38x/ddr3_init.h:17,
from drivers/ddr/marvell/a38x/ddr3_debug.c:6:
drivers/ddr/marvell/a38x/ddr3_training_ip_flow.h:116:47: note: previously declared as 'u32[]' {aka 'unsigned int[]'}
And similar warnings. Correct these by updating the prototype. Remove
the prototype for ddr3_tip_read_pup_value as it is unused.
projects / u-boot.git / log