Stefan Roese [Thu, 27 May 2010 14:45:20 +0000 (16:45 +0200)]
ppc4xx: Cleanup Boot/FLASH TLB reassignment for PPC440/460
Background Info:
Some PPC440/460 boards have caches enabled in the Boot/FLASH TLB (via
init.S) to speed up the boot process. In relocate_code (start.S) the
cache inhibit attribute for this TLB is set to disable cache. This is
needed for the CFI FLASH driver.
This patch now cleans this code up:
- CONFIG_SYS_TLB_FOR_BOOT_FLASH is defined to 0 (default TLB) if not
defined in the top of this file. This way, we can remove an ugly
#ifdef in this code.
- Replace complex "#if defined(CONFIG_440EP) || defined(CONFIG_GR)..."
statement with "#if defined(CONFIG_440)".
- Remove unnecessary cache invalidate calls resulting in faster bootup.
Stefan Roese [Tue, 25 May 2010 13:33:14 +0000 (15:33 +0200)]
ppc4xx: DDR2: Complete RDSS configuration on non-SPD based boards
As described in item #10 of the SDRAM initialization (chapter 22.2.9
of the PPC460EX/EXr/GT users manual), RDSS may need to be adjusted. The
code for this is now factored out and executed for non-SPD based boards
as well.
Stefan Roese [Tue, 25 May 2010 13:23:07 +0000 (15:23 +0200)]
ppc4xx: Enable overwriting of default scan window for IBM DDR2 controller
This patch makes it possible to overwrite the default auto-calibration
scan window (SDRAM_WRDTR.[WDTR], SDRAM_CLKTR.[CKTR] values) with
board specific values. The parameters of the weak default function are
corrected as well. This way we don't need the casts any more.
This feature will be used by an upcoming PPC460GT board port.
Stefan Roese [Fri, 21 May 2010 13:06:19 +0000 (15:06 +0200)]
ppc4xx: Enable PCIe support without PCI support on PPC440/460
By not defining CONFIG_SYS_PCI_MASTER_INIT and CONFIG_SYS_PCI_TARGET_INIT,
PCI support (host and adapter) will not be enabled. But it's still
possible to use the U-Boot PCI infrastructure for the PCIe ports.
This configuration option is needed for a new 460GT board, which uses
PCIe but has PCI disabled.
Stefan Roese [Wed, 19 May 2010 09:13:24 +0000 (11:13 +0200)]
ppc4xx: Enable booting with Option E on 460EX/EXr/GT
This patch enables booting with option E on the PPC460EX/EXr/GT.
When booting with Option E, the PLL is in bypass, CPR0_PLLC[ENG]=0.
The Software Boot Configuration Procedure is needed to engage the
PLL and perform a chip reset.
Mike Frysinger [Thu, 29 Apr 2010 04:35:12 +0000 (00:35 -0400)]
sf: move useful messages from debug to printf
At the moment, the default SPI flash subsystem is quite terse. Errors and
successes both result in a generic message. So move the useful errors and
useful successes to printf output by default.
While we're here, also convert the messages to use print_size().
Wolfgang Wegner [Fri, 23 Apr 2010 15:22:55 +0000 (17:22 +0200)]
add redundant environment for env_sf.c
This patch adds redundant environment for environment in SPI flash.
I took env_flash.c as an example and slightly modified it. Apart
from adapting things to SF, I also slightly changed the decision
logic to use area 2 as a default in case the flags are wrong because
not having a default path worried me.
I did not add a section for CONFIG_ENV_IS_IN_SPI_FLASH in environment.h
because I did not understand if this is desired and/or needed.
So to use the feature, one has to set CONFIG_ENV_OFFSET_REDUND _and_
CONFIG_SYS_REDUNDAND_ENVIRONMENT.
I checked it by powering off my board several times during flash
erase or write, because I do not know if there are other stress
test scenarios.
Signed-off-by: Wolfgang Wegner <w.wegner@astro-kom.de> Acked-by: Mike Frysinger <vapier@gentoo.org>
Becky Bruce [Wed, 30 Jun 2010 18:05:44 +0000 (13:05 -0500)]
drivers/usb/host/ohci-hcd: rename readl/writel to ohci_readl/ohci_writel
This avoids a build warning that you see if anyone in the
header chain has included io.h (which is coming shortly). The previous
code redefined readl/writel; this patch renames it to be specific to
ohci. The defines are also moved from ohci-hcd.c to ohci.h.
Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
musb: Use name based initialization for musb_config
Changed musb_config initialization for omap3.c, davinci.c
and da8xx.c using name of structure fields. This would cause
the uninitialized field to be null by default and thus would
help in avoiding to init some flags required to be set only
for a few selected platforms.
Add USB OHCI support for at91sam9g45ekes/at91sam9m10g45ek boards.
Note that according to errata from Atmel, OHCI is not operational
on the first revision of at91sam9g45 chip. So this patch enables
OHCI support for later revisions.
Sergei Shtylyov [Mon, 28 Jun 2010 18:44:49 +0000 (22:44 +0400)]
EHCI: zero out QH transfer overlay in ehci_submit_async()
ehci_submit_async() doesn't really zero out the QH transfer overlay (as the EHCI
specification suggests) which leads to the controller seeing the "token" field
as the previous call has left it, i.e.:
- if a timeout occured on the previous call (Active bit left as 1), controller
incorrectly tries to complete a previous transaction on a newly programmed
endpoint;
- if a halt occured on the previous call (Halted bit set to 1), controller just
ignores the newly programmed TD(s) and the function then keeps returning error
ad infinitum.
This turned out to be caused by the wrong orger of the arguments to the memset()
call in ehci_alloc(), so the allocated TDs weren't cleared either.
While at it, stop needlessly initializing the alternate next TD pointer in the
QH transfer overlay...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Acked-by: Remy Bohmer <linux@bohmer.net>
Felix Radensky [Sun, 27 Jun 2010 22:57:39 +0000 (01:57 +0300)]
tsec: Fix eTSEC2 link problem on P2020RDB
On P2020RDB eTSEC2 is connected to Vitesse VSC8221 PHY via SGMII.
Current TBI PHY settings for SGMII mode cause link problems on
this platform, link never comes up.
Fix this by making TBI PHY settings configurable and add a working
configuration for P2020RDB.
Signed-off-by: Felix Radensky <felix@embedded-sol.com> Acked-by: Andy Fleming <afleming@freescale.com> Acked-by: Peter Tyser <ptyser@xes-inc.com> Tested-by: Peter Tyser <ptyser@xes-inc.com>
Stefano Babic [Mon, 24 May 2010 10:08:16 +0000 (12:08 +0200)]
Tools: set multiple variable with fw_setenv utility
Add a sort of batch mode to fw_setenv, allowing to set
multiple variables in one shot, without updating the flash after
each set as now. It is added the possibility to pass
a config file with a list of pairs <variable, value> to be set,
separated by a TAB character.
Due to a hardware bug mentioned in latest AP7000 datasheet errata
(revision M from 09.09) branch folding is unreliable.
This patch disables CPUCR.FE bitfield as stated in datasheet.
Signed-off-by: Andreas Bießmann <biessmann@corscience.de>
Currently the U-Boot address ranges for AVR32 boards are
printed like this:
"U-Boot code: (null) -> 0001183c data: 000188e8 -> 0004e9b0"
This patch fixes this to print:
"U-Boot code: 00000000 -> 0001183c data: 000188f8 -> 0004e9c0"
Peter Tyser [Tue, 15 Jun 2010 19:48:25 +0000 (21:48 +0200)]
examples/standalone: Remove relocation compile flags for PowerPC
Previously, standalone applications were compiled with gcc flags that
produced relocatable executables on the PowerPC architecture (eg with
the -mrelocatable and -fPIC flags). There's no reason for these
applications to be fully relocatable at this time since no relocation
fixups are performed on standalone applications.
Additionally, removing the gcc relocation flags results in the entry
point of applications residing at the base of the image. When
a standalone application was relocatable, the entry point was generally
located at an offset into the image which was confusing and prone to
errors.
This change moves the entry point of PowerPC standalone applications
from 0x40004 (usually) to 0x40000.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com> Signed-off-by: Wolfgang Denk <wd@denx.de>
Anton Vorontsov [Fri, 18 Jun 2010 11:08:12 +0000 (15:08 +0400)]
hwconfig: Fix stop characters parsing for subkeys
For the following hwconfig string:
key1:subkey1=value1,subkey2=value2;key2:value3
The subkey2 cannot be extracted correctly. The parsing code looks
for comma as a stopch, but there may be two kind of stop characters:
a comma and a semicolon.
Currently the code would return "value2;key2:value3", while just
"value2" is the correct answer.
This patch fixes the issue by making the code aware of multiple
stop characters.
For old U-Boots, the issue can be workarounded by placing a comma
before a semicolon, i.e.:
Felix Radensky [Sun, 27 Jun 2010 22:57:39 +0000 (01:57 +0300)]
tsec: Fix eTSEC2 link problem on P2020RDB
On P2020RDB eTSEC2 is connected to Vitesse VSC8221 PHY via SGMII.
Current TBI PHY settings for SGMII mode cause link problems on
this platform, link never comes up.
Fix this by making TBI PHY settings configurable and add a working
configuration for P2020RDB.
Signed-off-by: Felix Radensky <felix@embedded-sol.com> Acked-by: Andy Fleming <afleming@freescale.com>
Wolfgang Denk [Mon, 28 Jun 2010 23:33:35 +0000 (01:33 +0200)]
MPC512x: workaround data corruption for unaligned local bus accesses
Commit 460c2ce3 "MPC5200: workaround data corruption for unaligned
local bus accesses" fixed the problem for MPC5200 only, but MPC512x is
affected as well, so apply the same fix here, too.
Signed-off-by: Wolfgang Denk <wd@denx.de> Cc: Detlev Zundel <dzu@denx.de> Cc: Anatolij Gustschin <agust@denx.de> Acked-by: Detlev Zundel <dzu@denx.de>
Wolfgang Denk [Sun, 13 Jun 2010 16:28:54 +0000 (18:28 +0200)]
Remove AmigaOneG3SE board
The AmigaOneG3SE board has been orphaned or a very long time, and
broken for more than 12 releases resp. more than 3 years. As nobody
seems to be interested any more in this stuff we may as well ged rid
of it, especially as it clutters many areas of the code so it is a
continuous pain for all kinds of ongoing work.
Wolfgang Denk [Sun, 13 Jun 2010 16:38:23 +0000 (18:38 +0200)]
Get rid of bogus CONFIG_SYS_BUS_HZ and CONFIG_SYS_CONFIG_BUS_CLK definitions
CONFIG_SYS_BUS_HZ has not really been used anywhere except to be
redined as CONFIG_SYS_BUS_CLK; in addition, the mpc7448hpc2 had the
bogus CONFIG_SYS_CONFIG_BUS_CLK setting which duplicated the
funtionality. Change all this to use CONFIG_SYS_BUS_CLK consistently.
Signed-off-by: Wolfgang Denk <wd@denx.de> Cc: Frank Gottschling <fgottschling@eltec.de> Cc: Reinhard Arlt <reinhard.arlt@esd-electronics.com> Cc: Eran Man <eran@nbase.co.il> Cc: Stefan Roese <sr@denx.de> Cc: Nye Liu <nyet@zumanetworks.com> Cc: Roy Zang <tie-fei.zang@freescale.com>
Wolfgang Denk [Mon, 21 Jun 2010 20:29:59 +0000 (22:29 +0200)]
MPC5200: workaround data corruption for unaligned local bus accesses
The MPC5200 has a nasty problem that will cause silent data corruption
when performing unaligned 16 or 32 byte accesses when reading from the
local bus - typically this affects reading from flash. The problem can
be easily shown:
This commit implements a workaround at least for the most blatant
problem: using memcpy() from NOR flash. We rename the assembler
routine into __memcpy() and provide a wrapper, which will use a
byte-wise copy loop for unaligned source or target addresses when
reading from NOR flash, and branch to the optimized __memcpy()
in all other cases, thus minimizing the performance impact.
Tested on lite5200b and TQM5200S.
Signed-off-by: Wolfgang Denk <wd@denx.de> Cc: Detlev Zundel <dzu@denx.de>
Minkyu Kang [Fri, 18 Jun 2010 10:31:10 +0000 (19:31 +0900)]
ARM: remove unused VIDEOLFB ATAG
ATAG_VIDEOLFB is not used anywhere.
The belowing warning is occurred due to this ATAG.
[ 0.000000] Ignoring unrecognised tag 0x54410008
This patch fixed it.
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Acked-by: Martin Krause <Martin.Krause@tqs.de>
Peter Horton [Sat, 12 Jun 2010 01:11:56 +0000 (10:11 +0900)]
UBI: initialise update marker
UBI: initialise update marker
The in kernel copy of a volume's update marker is not initialised from the
volume table. This means that volumes where an update was unfinnished will
not be treated as "forbidden to use". This is basically that the update
functionality was broken.
Signed-off-by: Peter Horton <zero@colonel-panic.org> Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Acked-by: Stefan Roese <sr@denx.de>
Ilya Yanok [Mon, 21 Jun 2010 14:13:21 +0000 (18:13 +0400)]
Makefile: always call date with LC_ALL=C set
Ensure that date is called only with LC_ALL=C locale set to make dates
locale neutral thus preventing lurking of non-ASCII characters into
U-Boot binary.
Signed-off-by: Ilya Yanok <yanok@emcraft.com>
Changed LANG= into LC_ALL= as suggested by Mike Frysinger <vapier@gentoo.org> Signed-off-by: Wolfgang Denk <wd@denx.de>
Vitaly Kuzmichev [Tue, 15 Jun 2010 18:18:11 +0000 (22:18 +0400)]
ARM: Align stack to 8 bytes
The ARM ABI requires that the stack be aligned to 8 bytes as it is noted
in Procedure Call Standard for the ARM Architecture:
http://infocenter.arm.com/help/topic/com.arm.doc.ihi0042d/index.html
Unaligned SP also causes the problem with variable-length arrays
allocation when VLA address becomes less than stack pointer during
aligning of this address, so the next 'push' in the stack overwrites
first 4 bytes of VLA.
Signed-off-by: Vitaly Kuzmichev <vkuzmichev@mvista.com>
Tested on tx25(mx25), imx27lite(mx27), qong(mx31) and trab(s3c2400) Tested-by: Wolfgang Denk <wd@denx.de>
Vitaly Kuzmichev [Tue, 15 Jun 2010 18:18:11 +0000 (22:18 +0400)]
ARM: Align stack to 8 bytes
The ARM ABI requires that the stack be aligned to 8 bytes as it is noted
in Procedure Call Standard for the ARM Architecture:
http://infocenter.arm.com/help/topic/com.arm.doc.ihi0042d/index.html
Unaligned SP also causes the problem with variable-length arrays
allocation when VLA address becomes less than stack pointer during
aligning of this address, so the next 'push' in the stack overwrites
first 4 bytes of VLA.
Nick Thompson [Tue, 22 Jun 2010 15:06:01 +0000 (11:06 -0400)]
Davinci: SPI performance enhancements
The following restructuring and optimisations increase the SPI
read performance from 1.3MiB/s (on da850) to 2.87MiB/s (on da830):
Remove continual revaluation of driver state from the core of the
copy loop. State can not change during the copy loop, so it is
possible to move these evaluations to before the copy loop.
Cost is more code space as loop variants are required for each set
of possible configurations. The loops are simpler however, so the
extra is only 128bytes on da830 with CONFIG_SPI_HALF_DUPLEX
defined.
Unrolling the first copy loop iteration allows the TX buffer to be
pre-loaded reducing SPI clock starvation.
Unrolling the last copy loop iteration removes testing for the
final loop iteration every time round the loop.
Using the RX buffer empty flag as a transfer throttle allows the
assumption that it is always safe to write to the TX buffer, so
polling of TX buffer full flag can be removed.
Signed-off-by: Nick Thompson <nick.thompson@ge.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Prakash PM [Tue, 22 Jun 2010 14:24:43 +0000 (10:24 -0400)]
DaVinci: EMAC: Get EMAC_MDIO_PHY_NUM from config files
Currently EMAC_MDIO_PHY_NUM is defined as 1 in emac_defs.h.
Because of this, EMAC does not work on EVMs which do not have phy
connected at 1. Moving the macro to board config file makes this
configurable depending on where the phy is connected on the MDIO bus.
This patch fixes the board reset issue observed during network access
on DM365EVM. EMAC driver was assuming EMAC_MDIO_PHY_NUM as 1
but it is 0 on DM365EVM.
This patch is verified on da830/omap-l137, dm365 and dm644x evms.
Fillod Stephane [Fri, 11 Jun 2010 17:26:43 +0000 (19:26 +0200)]
ip/defrag: fix processing of last short fragment
TFTP'ing a file of size 1747851 bytes with CONFIG_IP_DEFRAG and
CONFIG_TFTP_BLOCKSIZE set to 4096 fails with a timeout, because
the last fragment is not taken into account. This patch fixes
IP fragments having less than 8 bytes of payload.
Wolfgang Denk [Sun, 20 Jun 2010 00:16:44 +0000 (02:16 +0200)]
include/compiler.h: remove redundant declaration of errno
Commit 37566090 "compiler.h: unify system ifdef cruft here" added both
a "#include <errno.h>" and a "extern int errno;" to include/compiler.h
which is causing build warnings for some systems, for example for the
"netstar" board:
In file included from /home/wd/git/u-boot/work/lib/crc32.c:15:
include/compiler.h:28: warning: function declaration isn't a prototype
The declaration of "errno" should be redundant, as <errno.h> is
supposed to provide a correct declaration, so drop it.
Signed-off-by: Wolfgang Denk <wd@denx.de> Cc: Mike Frysinger <vapier@gentoo.org>
Wolfgang Denk [Thu, 17 Jun 2010 19:59:57 +0000 (21:59 +0200)]
Merge branch 'master' of git://git.denx.de/u-boot-ti
Conflicts:
CONFLICT (rename/add): Rename
board/davinci/da830evm/Makefile->board/ti/tnetv107xevm/Makefile
in 89b765c7f6ddfde07ba673dd4adbeb5da391a81b.
board/ti/tnetv107xevm/Makefile added in HEAD
But files were identical, so no problem.
Albert Aribaud [Thu, 17 Jun 2010 14:06:07 +0000 (19:36 +0530)]
Initial support for Marvell Orion5x SoC
This patch adds support for the Marvell Orion5x SoC.
It has no use alone, and must be followed by a patch
to add Orion5x support for serial, then support for
the ED Mini V2, an Orion5x-based product from LaCie.
Signed-off-by: Albert Aribaud <albert.aribaud@free.fr>
For boards using sm501/sm502 on PCI bus some driver
functions normaly defined in the board code are not
needed and empty. Provide weak default functions for
them and do not enforce board code to define empty
functions.
projects / u-boot.git / log