dwc3-generic: Don't fail probe if clk/reset entries are absent
Some boards don't populate clk/reset entries as these are are optional
as per binding documentation. Therefore, don't fail driver probe if
clk/reset entries are absent in DT.
This fixes fastboot failures seen due to enabling of CONFIG_CLK on AM57xx
Fixes: e8e683d33b0c ("board: ti: am57xx-idk: Configure the CDCE913 clock synthesizer") Reported-by: Sam Protsenko <semen.protsenko@linaro.org> Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Tom Rini [Wed, 30 Oct 2019 17:13:46 +0000 (13:13 -0400)]
Merge tag 'u-boot-clk-23Oct2019' of https://gitlab.denx.de/u-boot/custodians/u-boot-clk
- Add I2C clocks for i.MX6Q CCF driver
- Fix check in clk_set_default_parents()
- Managed API to get clock from device tree
- Fixes for core clock code (including sandbox regression tests)
Bin Meng [Mon, 28 Oct 2019 14:25:03 +0000 (07:25 -0700)]
Bring all testings in gitlab and travis CI to Azure Pipelines
This expands current Azure Pipelines Windows host tools build
testing to cover all the CI testing in gitlab and travis CI.
Note for some unknown reason, the 'container' cannot be used for
any jobs that have buildman, for buildman does not exit properly
and hangs the job forever. As a workaround, we manually call
docker to run the image to perform the CI tasks.
A complete run on Azure Pipelines takes about 2 hours and 10
minutes.
Bin Meng [Mon, 28 Oct 2019 14:25:01 +0000 (07:25 -0700)]
arm: mvebu: Avoid generating kwbimage.cfg in the source tree
At present some boards generate kwbimage.cfg in the source tree
during the build. This breaks buildman testing on some systems
where the source tree is read-only. Update makefile rules to
generate it in the build tree instead.
Note some other boards have the kwbimage.cfg file written in
advance, hence we need check if the file exists in the build
tree first, otherwise we fall back to one in the source tree.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Chris Packham <judge.packham@gmail.com> Reviewed-by: Stefan Roese <sr@denx.de> Reviewed-by: Simon Glass <sjg@chromium.org>
Peng Fan [Wed, 23 Oct 2019 01:43:30 +0000 (01:43 +0000)]
spl: spl_mmc: fix getting raw_sect when boot from emmc boot partition
On i.MX8, when booting from eMMC boot partition, the whole flash.bin
is stored in boot partition, however SPL switches to user partition
during the init of mmc driver:
spl_mmc_load() -> mmc_init()
Then it tries to load the container image in
spl_mmc_get_uboot_raw_sector(), but here it reads the data from user
partition and the header is not recognized as a valid header.
So we move spl_mmc_get_uboot_raw_sector after eMMC partition switch
to address this issue.
Anyway put spl_mmc_get_uboot_raw_sector before eMMC partition switch
is not correct, so let's move it after eMMC partition switch.
Reported-by: Anatolij Gustschin <agust@denx.de> Signed-off-by: Peng Fan <peng.fan@nxp.com>
Yangbo Lu [Mon, 21 Oct 2019 10:09:09 +0000 (18:09 +0800)]
mmc: fsl_esdhc: drop i.MX DDR support code
A previous patch below adding DDR mode support was actually for i.MX
platforms. Now i.MX eSDHC driver is fsl_esdhc_imx.c. For QorIQ eSDHC,
it uses different process for DDR mode, and hasn't been supported.
Let's drop DDR support code for i.MX in fsl_esdhc driver.
Bin Meng [Sun, 27 Oct 2019 12:19:48 +0000 (05:19 -0700)]
Add Microsoft Azure Pipelines configuration
Microsoft Azure Pipelines [1] provides unlimited CI/CD minutes and
10 parallel jobs to every open source project for free.
This adds a configuration file for Azure Pipelines to utilize the
free Windows VM hosted by Microsoft to ensure no build broken in
building U-Boot host tools for Windows.
Bin Meng [Sun, 27 Oct 2019 12:19:47 +0000 (05:19 -0700)]
tools: Avoid creating symbolic links for tools/version.h
When building U-Boot host tools for Windows from Microsoft Azure
Pipelines, the following errors were seen:
HOSTCC tools/mkenvimage.o
In file included from tools/mkenvimage.c:25:
./tools/version.h:1:1: error: expected identifier or ‘(’ before ‘.’ token
1 | ../include/version.h
| ^
tools/mkenvimage.c: In function ‘main’:
tools/mkenvimage.c:117:4: warning: implicit declaration of function ‘usage’ [-Wimplicit-function-declaration]
117 | usage(prg);
| ^~~~~
tools/mkenvimage.c:120:35: error: ‘PLAIN_VERSION’ undeclared (first use in this function)
120 | printf("%s version %s\n", prg, PLAIN_VERSION);
| ^~~~~~~~~~~~~
tools/mkenvimage.c:120:35: note: each undeclared identifier is reported only once for each function it appears in
make[2]: *** [scripts/Makefile.host:114: tools/mkenvimage.o] Error 1
It turns out tools/version.h is a symbolic link and with Windows
default settings it is unsupported hence the actual content of
tools/version.h is not what file include/version.h has, but the
the linked file path, which breaks the build.
To fix this, remove the symbolic links for tools/version.h. Instead
we perform a copy from include/version.h during the build.
Bin Meng [Sun, 27 Oct 2019 12:19:46 +0000 (05:19 -0700)]
Add .gitattributes for line endings
When building U-Boot host tools for Windows from Microsoft Azure
Pipelines, we see tons of weird warnings and errors emitted from
every Kconfig files:
Kconfig:6:warning: ignoring unsupported character ''
Kconfig:6:warning: ignoring unsupported character ''
Kconfig:8:warning: ignoring unsupported character ''
Kconfig:9:warning: ignoring unsupported character ''
Kconfig:10:warning: ignoring unsupported character ''
Kconfig:10:warning: ignoring unsupported character ''
Kconfig:13:warning: ignoring unsupported character ''
arch/Kconfig:1:warning: ignoring unsupported character ''
arch/Kconfig:2:warning: ignoring unsupported character ''
arch/Kconfig:2:warning: ignoring unsupported character ''
arch/Kconfig:4:warning: ignoring unsupported character ''
...
After several rounds of experiments, it turns out this is caused
by line endings. Historically, Linux and macOS used linefeed (LF)
characters while Windows used a carriage return plus a linefeed
(CRLF). When Azure Pipelines checks out the U-Boot repo, Git tries
to compensate for the difference by automatically making lines end
in CRLF in the working directory on Windows, which confuses the
Kconfig file parsing logic.
Fortunately Git provides a way for repos to tell Git not to do such
automatical line endings conversion via .gitattributes file below:
Bin Meng [Sun, 27 Oct 2019 12:19:43 +0000 (05:19 -0700)]
linux/types.h: Surround 'struct ustat' with __linux__
'struct ustat' uses linux-specific typedefs to declare its memebers:
__kernel_daddr_t and __kernel_ino_t. It is currently not used by any
U-Boot codes, but when we build U-Boot tools for other platform like
Windows, this becomes a problem.
Bin Meng [Sun, 27 Oct 2019 12:19:42 +0000 (05:19 -0700)]
tools: zynqmpbif: Use compiler builtin instead of linux-specific __swab32
__swab32() is a Linux specific macro defined in linux/swab.h. Let's
use the compiler equivalent builtin function __builtin_bswap32() for
better portability.
Tom Rini [Sat, 26 Oct 2019 00:07:24 +0000 (20:07 -0400)]
Merge tag 'mips-pull-2019-10-25' of git://git.denx.de/u-boot-mips
- bmips: add BCRM NAND support for BCM6368, BCM6328, BCM6362 and BCM63268 SoCs
- bmips: various small fixes
- mtmips: add new drivers for clock, reset-controller and pinctrl
- mtmips: add support for high speed UART
- mtmips: update/enhance drivers for SPI and ethernet
- mtmips: add support for MMC
Suman Anna [Thu, 17 Oct 2019 03:33:08 +0000 (09:03 +0530)]
arm: dts: k3-am65: Add R5F ranges in interconnect nodes
Add the address spaces for the R5F cores in MCU domain to the ranges
property of the cbass_mcu interconnect node so that the addresses
within the R5F nodes can be translated properly by the relevant OF
address API.
Signed-off-by: Suman Anna <s-anna@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Lokesh Vutla [Mon, 7 Oct 2019 13:56:38 +0000 (19:26 +0530)]
armv7R: K3: j721e: Add support for triggering ddr init from SPL
In SPL, DDR should be made available by the end of board_init_f()
so that apis in board_init_r() can use ddr. Adding support for
triggering DDR initialization from board_init_f().
Kevin Scholz [Mon, 7 Oct 2019 13:56:36 +0000 (19:26 +0530)]
ram: k3-j721e: Add support for J721E DDR controller
The J721E DDR subsystem comprises DDR controller, DDR PHY and wrapper
logic to integrate these blocks in the device. The DDR subsystem is
used to provide an interface to external SDRAM devices which can be
utilized for storing program or data. Introduce support for the
DDR controller and DDR phy within the DDR subsystem.
Signed-off-by: Kevin Scholz <k-scholz@ti.com Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
James Doublesin [Mon, 7 Oct 2019 08:34:27 +0000 (14:04 +0530)]
ram: k3-am654: Do not rely on default values for certain DDR register
Added the following registers to the DDR configuration:
- ACIOCR0,
- ACIOCR3,
- V2H_CTL_REG,
- DX8SLxDQSCTL.
Modified enable_dqs_pd and disable_dqs_pd to only touch the associated
bit fields for pullup and pulldown registers (to preserve slew rate and
other bits in that same register). Also update the dts files in the same
patch to maintain git bisectability.
Signed-off-by: James Doublesin <doublesin@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
James Doublesin [Mon, 7 Oct 2019 08:34:25 +0000 (14:04 +0530)]
armv7r: dts: am654-base-board: Rename 1600MHz to 1600MTs in dtsi filename
The current configuration of DDR on AM654 base board is for 1600MTs but
the file name is specified as k3-am654-base-board-ddr4-1600MHz.dtsi.
Since 1600MHz is misleading, rename it to
k3-am654-base-board-ddr4-1600MTs.dtsi
Signed-off-by: James Doublesin <doublesin@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Lokesh Vutla [Mon, 7 Oct 2019 08:22:17 +0000 (13:52 +0530)]
arm: K3: Clean and invalidate Linux Image before jumping to Linux
U-Boot cleans and invalidate L1 and L2 caches before jumping to Linux
by set/way in cleanup_before_linux(). Additionally there is a custom
hook provided to clean and invalidate L3 cache.
Unfortunately on K3 devices(having a coherent architecture), there is no
easy way to quickly clean all the cache lines for L3. The entire address
range needs to be cleaned and invalidated by Virtual Address. This can
be implemented using the L3 custom hook but it take lot of time to clean
the entire address range. In the interest of boot time this might not be
a viable solution.
The best hit is to make sure the loaded Linux image is flushed so that
the entire image is written to DDR from L3. When Linux starts running with
caches disabled the full image is available from DDR.
Reported-by: Andrew F. Davis <afd@ti.com> Reported-by: Faiz Abbas <faiz_abbas@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
zynqmp:
- Clean firmware handing via drivers/firmware/
- DT/defconfig name alignments
- DT cleanups with using firmware based clock driver
- Some defconfig updates
- Add IIO ina226 DT description
- Tune zynqmp_psu_init_minimalize.sh script
- Add single nand mini configuration, e-a2197, m-a2197-02/03 and zcu216
versal:
- Clean firmware handing via drivers/firmware/
- Add gpio support
- Enable DT overlay/USB/CLK/FPGA
- DT updates
- Tune mini configuration
dts: mtmips: add default pinctrl to eth nodes for all boards
This patch adds default eth pinctrl for all boards.
There are two pinctrl nodes used for two scenarios:
ephy_iot_mode - for IOT boards which have only one port (PHY0)
ephy_router_mode - For routers which have more than one ports
Reviewed-by: Stefan Roese <sr@denx.de> Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
net: mt7628-eth: free rx descriptor on receiving failure
When received a packet with an invalid length recorded in rx descriptor,
we should free this rx descriptor to allow us to continue to receive
following packets.
Without doing so, u-boot will stuck in a dead loop trying to process this
invalid rx descriptor.
This patch adds a call to mt7628_eth_free_pkt() after received an invalid
packet length.
Reviewed-by: Stefan Roese <sr@denx.de> Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
net: mt7628-eth: make phy link up detection optional via DT
The mt7628 has an embedded ethernet switch (5 phy ports + 1 cpu port).
Although in IOT mode only port0 is usable, the phy0 is still connected
to the switch, not the ethernet gmac directly.
This patch rewrites it and makes it optional. It can be turned on by adding
mediatek,poll-link-phy = <?> explicitly into the eth node. By default the
driver is switch mode with all 5 phy ports working without link detection.
net: mt7628-eth: remove hardcoded gpio settings and regmap-based phy reset
This patch removes hardcoded gpio settings as they have been replaced by
pinctrl in dts, and also replaces regmap-based phy reset with a more
generic reset controller.
Reviewed-by: Stefan Roese <sr@denx.de> Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
phy: mt76x8-usb-phy: add slew rate calibration and remove non-mt7628 part
This patch adds slew rate calibration for mt76x8-usb-phy, removes code
which belongs to mt7620, and gets rid of using syscon and regmap by using
clock driver and reset controller.
spi: mt7621-spi: restore default register value after each xfer
Currently this driver uses a different way to implement the spi xfer,
by modifying some fields of two registers, which is incompatible with the
MTK's original SDK linux driver. This will cause the flash data being
damaged by the SDK driver.
This patch lets the mt7621_spi_set_cs() restore the original register
fields after cs deactivated.
Reviewed-by: Stefan Roese <sr@denx.de> Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
spi: mt7621-spi: remove data cache and rewrite its xfer function
The mt7621 spi controller supports continuous generic half-duplex spi
transaction. There is no need to cache xfer data at all.
To achieve this goal, the OPADDR register must be used as the first data
to be sent. And follows the eight generic DIDO registers. But one thing
different between OPADDR and DIDO registers is OPADDR has a reversed byte
order.
With this patch, any amount of data can be read/written in a single xfer
function call.
Reviewed-by: Stefan Roese <sr@denx.de> Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
clk: add clock driver for MediaTek MT76x8 platform
This patch adds a clock driver for MediaTek MT7628/7688 SoC.
It provides clock gate control as well as getting clock frequency for
CPU/SYS/XTAL and some peripherals.
dts: mtmips: enable high-speed UART support for mt7628
All three UARTs of mt7628 are actually MediaTek's high-speed UARTs which
support baudrate up to 921600.
The high-speed UART is compatible with ns16550 when baudrate <= 115200.
Add compatible string to dtsi file so u-boot can use it when serial_mtk
driver is built in.
Reviewed-by: Stefan Roese <sr@denx.de> Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
This patch adds non-DM version for mtk hsuart driver and makes it
compatible with ns16550a driver in configuration.
This is needed in SPL with CONFIG_SPL_DM disabled for reducing size.
The current brcmnand driver is based on 4.18 linux kernel which uses
mtd_set_ooblayout to set ecc layout. But nand base code in u-boot is from
old kernel which does not use this new API and expect nand_chip.ecc.layout
structure to be set. This cause nand_scan_tail function running into a bug
check if the device has a different oob size than the default ones.
This patch ports the brcmstb_choose_ecc_layout function from kernel 4.6.7
that supports the ecc layout struture and replaces the mtd_set_ooblayout
method
Signed-off-by: William Zhang <william.zhang@broadcom.com> Reviewed-by: Philippe Reynes <philippe.reynes@softathome.com>
Ramon Fried [Mon, 10 Jun 2019 18:05:26 +0000 (21:05 +0300)]
MIPS: add compile time definition of L2 cache size
If configuration is set to skip low level init, automatic
probe of L2 cache size is not performed and the size is set to 0.
Flushing or invalidating the L2 cache will fail in this case.
Add a static configuration (SYS_DCACHE_LINE_SIZE) with default set to 0.
sunxi: set PIO voltage to hardware-detected value on startup on H6
The Allwinner H6 SoC has a register to set the PIO banks' voltage. When
it mismatches the real voltage supplied to the VCC to the PIO supply,
the PIO will work improperly.
The PIO controller also has a register that contains the status of each
VCC rail of the PIO supplies, and it has the same definition with the
configuration register. so we can just copy the content of this register
to the configuration register at startup, to ensure the configuration is
correct at startup stage.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
[jagan: s/__maybe__unused/__maybe_unused] Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Acked-by: Jagan Teki <jagan@amarulasolutions.com>
Stefan Mavrodiev [Wed, 31 Jul 2019 13:15:52 +0000 (16:15 +0300)]
sunxi: Fix pll1 clock calculation
clock_sun6i.c is used for sun6i, sun8i and sun50i SoC families.
PLL1 clock sets the default system clock, defined as:
sun6i: 1008000000
sun8i: 1008000000
sun50i: 816000000
With the current calculation, m = 2 and k = 3. Solving for n,
this results 28. Solving back:
(24MHz * 28 * 3) / 2 = 1008MHz
However if the requested clock is 816, n is 22.66 rounded
to 22, which results:
(24MHz * 28 * 3) / 2 = 792MHz
Changing k to 4 satisfies both system clocks:
(24E6 * 21 * 4) / 2 = 1008MHz
(24E6 * 17 * 4) / 2 = 816MHz
Signed-off-by: Stefan Mavrodiev <stefan@olimex.com> Acked-by: Jagan Teki <jagan@amarulasolutions.com>
arm64: dts: sun50i: Add support for A64 OLinuXino (with eMMC)
A64 OLinuXino board from Olimex has three variants with onboard eMMC:
A64-OLinuXino-1Ge16GW, A64-OLinuXino-1Ge4GW and A64-OLinuXino-2Ge8G-IND. In
addition, there are two variants without eMMC. One without eMMC and one with SPI
flash. This suggests the need for separate device tree for the three eMMC
variants.
The Linux kernel upstream has chosen to create and use a separate device tree
for the eMMC variants instead of adding eMMC support existing device tree. These
changes to Linux kernel are queued for Linux 5.4.
Jernej Skrabec [Fri, 23 Aug 2019 17:24:04 +0000 (19:24 +0200)]
sunxi: H6: DRAM: Add support for half DQ
Half DQ configuration seems to be very rare for H6 based boards/STBs,
but exists nevertheless. Currently the only known product which needs
this support is Tanix TX6 mini.
This commit adds support for half DQ configuration. Code was tested
for regressions on other configurations (OrangePi 3 1 GiB/LPDDR3, Tanix
TX6 4 GiB/DDR3) and none were found.
Thanks to Icenowy Zheng for help with this code.
Reviewed-by: Andre Przywara <andre.przywara@arm.com> Tested-by: thomas graichen <thomas.graichen@gmail.com> Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net> Reviewed-by: Maxime Ripard <mripard@kernel.org>
Frieder Schrempf [Wed, 23 Oct 2019 07:41:20 +0000 (07:41 +0000)]
mtd: spi: Clean up usage of CONFIG_SPI_FLASH_MTD
Most boards currently use SPI_FLASH_MTD only in U-Boot proper, not in
SPL. They often rely on hacks in the board header files to include
this option conditionally. To be able to fix this, we previously
introduced a separate option SPL_SPI_FLASH_MTD.
Therefore we can now adjust the Makefile and change the code in
sf_probe.c and sf_internal.h to use CONFIG_IS_ENABLED(SPI_FLASH_MTD).
We also need to move all occurences of CONFIG_SPI_FLASH_MTD from the
header files to the according defconfigs. The affected boards are
socfpga, aristainetos, cm_fx6, display5, ventana, rcar-gen2, dh_imx6
and da850evm.
We do this all in one patch to guarantee bisectibility.
This change was tested with buildman to make sure it does not
introduce any regressions by comparing the resulting binary sizes.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de> Reviewed-by: Stefan Roese <sr@denx.de> Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com> Acked-by: Lukasz Majewski <lukma@denx.de> Reviewed-by: Heiko Schocher <hs@denx.de> Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
spi-nor: spi-nor-ids: Add USE_FSR flag for mt25q* and n25q* entry
n25q* and mt25q* (both 256Mb and 512Mb) flashes support Flag status
register that indicates various errors that may be encountered during
erase/write operations. Therefore add USE_FSR flag wherever missing.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com> Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com> Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com> Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
spi-nor: spi-nor-ids: Add entries for mt25q variants
mt25q* flashes support stateless 4 byte addressing opcodes. Add entries
for the same. These flashes have bit 6 set in 5th byte of READ ID
response when compared to n25q* variants.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com> Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com> Tested-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com> Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
spi-nor: spi-nor-ids: Disable SPI_NOR_4B_OPCODES for n25q512* and n25q256*
Per datasheets of n25q256* and n25q512* not all variants of n25q256* and
n25q512* support 4 Byte stateless addressing opcodes. Therefore drop
SPI_NOR_4B_OPCODES flag from these entries
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com> Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com> Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com> Tested-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com> Tested-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com> Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
projects / u-boot.git / log