Denys Drozdov [Wed, 6 Oct 2021 16:55:33 +0000 (18:55 +0200)]
toradex: configblock: fix interactive mode it handling
Restore "Is the module an IT version? [y/N]" for "cfgblock create"
interactive mode command, which was leading to invalid detection
of 0051 Colibri iMX8DX 1GB WB module;
Fabio Estevam [Mon, 23 Aug 2021 12:56:42 +0000 (09:56 -0300)]
imx8mm-evk: Generate a single bootable flash.bin again
After the conversion to binman in commit 8996e6b7c6a1 ("imx8mm_evk: switch
to use binman to pack images"), it is necessary to flash both flash.bin and
u-boot.itb to get a bootable system. Prior to this commit, only flash.bin
was needed.
Such new requirement breaks existing distro mechanisms to generate the
final binary because the extra u-boot.itb is now required.
Generate a final flash.bin that can be used again as a single
bootable binary to keep the original behavior.
After this change the SPL binary is called spl.bin, which is a more
descriptive name for its purpose, and can still be used standalone
(for example, for secure boot purposes).
Also update imx8mm_evk.rst to remove the u-boot.itb copy step.
NXP used to setup the gpmi clock root from gpmi_clk in early versions
in their downstream BSP. [1]
However on mainline the gpmi clock root was always setup from enfc
since the beginning of the i.MX 6 series SoCs, which is still the same
today. [2]
NXP followed the mainline approach at some point and changed
setup_gpmi_io_clk to setup gpmi clock root from enfc which left faulty
code behind in our board file. [3]
This commit follows the change of NXP as it improves the performance of
the NAND from ~1.2 MiB/s to ~12 MiB/s. [3]
This change was verified to work in recovery-mode and u-boot loaded
from NAND on all four Colibri iMX6ULL SKUs from Toradex.
The frequency used to read the NAND, measured on RE# (Read Enable):
before this patch: 1.4 MHz
after this patch: 22 MHz
in Linux Kernel: 50 MHz
[1] https://source.codeaurora.org/external/imx/uboot-imx/tree/arch/arm/cpu/armv7/mx6/clock.c?h=nxp/imx_v2016.03_4.1.15_2.0.0_ga#n62
[2] commit 23608e23fd65 ("i.mx: add the initial support for freescale i.MX6Q processor")
[3] https://source.codeaurora.org/external/imx/uboot-imx/commit/?id=7a82a19ceabfb04bbc1591a67c99751748781c7d
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Turns out while the watchdog node itself was already u-boot,dm-spl its
pinctrl node was not which caused it to be unavailable at that early
stage. Note that any and all other boards I checked also seem to be
missing this. However, I can't judge whether or not they might indeed
need a similar fix or not.
Igor Opaniuk [Sat, 9 Oct 2021 20:41:12 +0000 (22:41 +0200)]
verdin-imx8mm: use preboot for fdtfile evaluation
Enable and set preboot var with fdtfile evaluation.
It will be checked and run immediately before starting the
CONFIG_BOOTDELAY countdown and/or running the auto-boot command resp.
entering interactive mode.
This provides possibility to use different boot cmds in interactive mode
without manual setting fdtfile value, as it it's already evaluated
before entering interactive mode.
Variable "kernel_image" is used in boot.scr script only, that sets its
own default value to the constant string @@KERNEL_IMAGETYPE@@ in case
"kernel_image" is not set.
The default name of the kernel image shipped with BSP 5.x is "Image.gz".
Setting kernel_image="Image" as a pre-defined u-boot variable
breaks booting systems with modern versions of boot.scr, whereas
renaming it fixes booting with modern scripts and does not break working
of earlier versions of boot.scr.
While at it also update the copyright period, rather than hard-coding
fdtfile default fdt_board to dev for the Verdin iMX8M Mini and fix its
closing #endif comment.
Marcel Ziswiler [Sat, 9 Oct 2021 20:41:05 +0000 (22:41 +0200)]
ARM: dts: imx8mm-verdin: prepare for dek blob encapsulation
Prepare for DEK blob encapsulation support through "dek_blob" command.
On ARMv8, u-boot runs in non-secure, thus cannot encapsulate a DEK blob
for encrypted boot.
The DEK blob is encapsulated by OP-TEE through a trusted application
call. U-boot sends and receives the DEK and the DEK blob binaries
through OP-TEE dynamic shared memory.
To enable the DEK blob encapsulation, add to the defconfig:
CONFIG_SECURE_BOOT=y
CONFIG_FAT_WRITE=y
CONFIG_CMD_DEKBLOB=y
Taken from NXP's commit 56d2050f4028 ("imx8m: Add DEK blob encapsulation
for imx8m").
Marcel Ziswiler [Sat, 9 Oct 2021 20:41:04 +0000 (22:41 +0200)]
verdin-imx8mm: fix ethernet
Turns out Microship (formerly Micrel) meanwhile integrated proper
support for the DLL setup on their KSZ9131. Unfortunately, this
conflicts with our previous board code doing that.
Fix this by getting rid of our board code and just relying on the
generic implementation relying on rgmii-id being used as phy-mode.
Fixes: commit c6df0e2ffdc4
("net: phy: micrel: add support for DLL setup on ksz9131") Fixes: commit af2d3c91d877
("ARM: dts: imx8mm-verdin: Set PHY mode to RGMII-ID") Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Reviewed-by: Fabio Estevam <festevam@gmail.com>
Stefano Babic [Wed, 20 Oct 2021 10:13:44 +0000 (12:13 +0200)]
imx8mm-cl-iot-gate-optee: align config with Kconfig
Due to missing configs, CI goes in deadlock until an OOM is tracked. Add
CONFIG_SYS_LOAD_ADDR and replace CONFIG_SYS_EXTRA_OPTIONS with
CONFIG_IMX_CONFIG.
Stefano Babic [Wed, 20 Oct 2021 09:55:25 +0000 (11:55 +0200)]
kontron-sl-mx8mm: fix missing configs and deadlock in CI
Even if board can be successfuly built, CI goes in deadlock (see thread
on https://www.mail-archive.com/u-boot@lists.denx.de/msg419663.html).
This is caused by SYS_CONFIG set in header file and because defconfig
for the board is out of sync with Kconfig. As result, buildman goes on
to read from stdin until an OOM is reached.
Simon Glass [Wed, 20 Oct 2021 03:43:24 +0000 (21:43 -0600)]
buildman: Detect Kconfig loops
Hex and int Kconfig options are supposed to have defaults. This is so we
can configure U-Boot without having to enter particular values for the
items that don't have specific values in the board's defconfig file.
If this rule is not followed, then introducing a new Kconfig can produce
a loop like this:
Break things (BREAK_ME) [] (NEW)
Error in reading or end of file.
Break things (BREAK_ME) [] (NEW)
Error in reading or end of file.
The continues forever since buildman passes /dev/null to 'conf', and
the build system just tries again. Eventually there is so much output that
buildman runs out of memory.
We can detect this situation by looking for a symbol (like 'BREAK_ME')
which has no default (the '[]' above) and is marked as new. If this
appears multiple times in the output, we know something is wrong.
Add a filter function for the output which detects this situation. Allow
it to return True to terminate the process. Implement this termination in
cros_subprocess.
With this we get a nice message:
buildman --board sandbox -T0
Building current source for 1 boards (0 threads, 32 jobs per thread)
sandbox: w+ sandbox
+.config:66:warning: symbol value '' invalid for BREAK_ME
+
+Error in reading or end of file.
+make[3]: *** [scripts/kconfig/Makefile:75: syncconfig] Terminated
+make[2]: *** [Makefile:569: syncconfig] Terminated
+make: *** [Makefile:177: sub-make] Terminated
+(** did you define an int/hex Kconfig with no default? **)
Simon Glass [Wed, 20 Oct 2021 03:43:23 +0000 (21:43 -0600)]
buildman: Write output even on fatal error
At present buildman does not write any output (to the 'out' and 'err)
files if the build terminates with a fatal error. This is to avoid adding
lots of spam to the logs.
However there are times when this is actually useful, such as when the
build fails for an obscure reason such as a Kconfig loop.
Update the logic to always write the output, so that the user gets a clue
as to what is happening.
Marek Vasut [Sat, 11 Sep 2021 22:40:00 +0000 (00:40 +0200)]
ARM: imx: mx5: Add altbootcmd and resets to M53Menlo
Bulletproof the default boot command with reset statements in case
any command in the chain would fail. In case a failure were to happen,
the board will reset, increment boot counter and retry the procedure.
In case the failures persist and the boot counter reaches the bootlimit,
U-Boot starts altbootcmd instead of the default bootcmd boot command.
The altbootcmd swaps the default boot partition for the other boot
partition, which is an identical copy or an older copy, and tries
booting from that one instead.
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Stefano Babic <sbabic@denx.de>
mmc: sdhci-esdhc-imx: Add HS400 support for iMX7ULP
Import HS400 support for iMX7ULP B0 from the Linux kernel:
2eaf5a533afd ("mmc: sdhci-esdhc-imx: Add HS400 support for iMX7ULP")
According to IC suggest, need to clear the STROBE_DLL_CTRL_RESET
before any setting of STROBE_DLL_CTRL register.
USDHC has register bits(bit[27~20] of register STROBE_DLL_CTRL)
for slave sel value. If this register bits value is 0, it needs
256 ref_clk cycles to update slave sel value. IC suggest to set
bit[27~20] to 0x4, it only need 4 ref_clk cycle to update slave
sel value. This will short the lock time of slave.
i.MX7ULP B0 will need more time to lock the REF and SLV, so change
to add 5us delay.
Peng Fan [Mon, 16 Aug 2021 03:48:45 +0000 (11:48 +0800)]
imx: makefile: drop the use of imx8mimage.sh
After switch to use binman, no need to use the bash script
to check file exsiting or not. And there is bug that
the script will be executed everytime Makefile is used which is
confusing people.
Signed-off-by: Peng Fan <peng.fan@nxp.com> Tested-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Peng Fan [Mon, 16 Aug 2021 03:48:41 +0000 (11:48 +0800)]
tools: imx8mimage: not abort when mmap fail
When creating flash.bin, the hdmi firmware might not be
copied to U-Boot source tree. Then mkimage will fail.
However we are switching to binman, binman will show the
message if the file not there, and create empty file per
i.MX8MQ binman node. So we not fail mkimage here othersize
CI will fail if hdmi firmware not copied here.
Tim Harvey [Wed, 29 Sep 2021 22:04:22 +0000 (15:04 -0700)]
imx: ventana: fix USB hub reset
Remove board_ehci_hcd_init function that is not used with DM_USB
and replace its functionality with device-tree configuraton that treats
USB HUB RST# as a gpio enable for the usbh1 vbus regulator.
Tim Harvey [Wed, 29 Sep 2021 22:04:21 +0000 (15:04 -0700)]
imx: ventana: update LVDS support
Enable LVDS display detection and panel-specific configuration
Make I2C based LVDS detection and configuration model specific:
- not all boards support LVDS connectors; fail detection that do not
support LVDS to avoid misdetecting an I2C device as a display
- GPIO configuration is panel specific; use panel name where needed
Tim Harvey [Wed, 29 Sep 2021 22:04:18 +0000 (15:04 -0700)]
imx: ventana: remove phy gpio reset from dt
We configure network phy configuration for internal delay, LED config,
and clock config. If we leave the phy reset gpio defined in dt the
kernel may issue a reset to the phy and break these configs. While some
may be handled by a kernel phy driver, others may not (typically LED
config).
imx: imx6ul: Add support for Kontron Electronics SL/BL i.MX6UL/ULL boards (N63xx/N64xx)
This adds support for i.MX6UL/ULL-based evaluation kits with SoMs by
Kontron Electronics GmbH.
Currently there are the following SoM flavors (SoM-Line):
* N6310: SOM with i.MX6UL-2, 256MB RAM, 256MB SPI NAND
* N6311: SOM with i.MX6UL-2, 512MB RAM, 512MB SPI NAND
* N6411: SOM with i.MX6ULL, 512MB RAM, 512MB SPI NAND
And the according evaluation boards (Board-Line):
* N6310-S: Baseboard with SOM N6310, eMMC, display (optional), ...
* N6311-S: Baseboard with SOM N6311, eMMC, display (optional), ...
* N6411-S: Baseboard with SOM N6411, eMMC, display (optional), ...
Currently U-Boot describes i.MX6UL and i.MX6ULL through separate config
options at compile-time. Though the differences are so minor, that for
the scope of these SoMs we just use a single defconfig that is compatible
with both SoCs.
The CONFIG_SPL_MAX_SIZE definition did not account for all areas that
are used by the boot ROM according to the manual, causing boot failures
due to truncated SPL images when actually hitting this limit.
Synchronize the u-boot and kernel imx device trees, using tuned
script from commit c0157bdcafa1 ("ARM: dts: imx: use generic name bus")
Per devicetree specification, generic names are recommended to be
used, such as bus.
i.MX AIPS is an AHB - IP bridge bus, so we could use bus as node
name.
Script:
sed -i "s/\<aips@/bus@/" arch/arm/dts/imx*.dtsi
sed -i "s/\<aips@/bus@/" arch/arm/dts/vf*.dtsi
sed -i "s/\<aips-bus@/bus@/" arch/arm/dts/imx*.dtsi
sed -i "s/\<aips-bus@/bus@/" arch/arm/dts/vf*.dtsi
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io> Reviewed-by: Peng Fan <peng.fan@nxp.com>
Ye Li [Thu, 23 Sep 2021 14:01:15 +0000 (17:01 +0300)]
mx7ulp: Update wdog disable sequence
Update the mx7ulp wdog disable sequence to avoid potential reset
issue in unlock or refresh sequence. Both sequence need two words
write to wdog CNT register in 16 bus clocks window, if miss the
window, the write will cause violation in wdog and reset the chip.
Current u-boot code is using writel() function which has a DMB
barrier to order the memory access. The DMB between two words write
may introduce some delay in certain circumstance, causing the wdog
reset due to 16 bus clock window requirement.
Also, WDOG1 might have been enabled already depending on FUSE hence
we need to be as close as possible to its reconfiguration timing
requirement of 128 bus clock limit.
This patch replaces writel() function by __raw_writel() to avoid such
issue, and improve to check if watchdog is already disabled or
unlocked.
Marek Vasut [Sat, 11 Sep 2021 22:43:18 +0000 (00:43 +0200)]
ARM: dts: imx8mm-verdin: Set PHY mode to RGMII-ID
Since c6df0e2ffdc ("net: phy: micrel: add support for DLL setup on ksz9131")
the Micrel PHY driver correctly configures the delay register. The Verdin PHY
is RGMII-ID, so reflect that in DT, otherwise the ethernet no longer works.
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com> Cc: Max Krummenacher <max.krummenacher@toradex.com> Cc: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
The BSP platform LmP supports the board NXP iMX8QM MEK. The
kernel size in LmP exceeds 32Mb. Increase the maximum size
of an uncompressed kernel to fix the following error:
Uncompressing Kernel Image
Error: inflate() returned -5
Image too large: increase CONFIG_SYS_BOOTM_LEN
Must RESET board to recover
The BSP platform LmP supports the board NXP iMX8M Plus EVK. The
kernel size in LmP exceeds 32Mb. Increase the maximum size
of an uncompressed kernel to fix the following error:
Uncompressing Kernel Image
Error: inflate() returned -5
Image too large: increase CONFIG_SYS_BOOTM_LEN
Must RESET board to recover
The BSP platform LmP supports the board NXP iMX8M Mini EVK. The
kernel size in LmP exceeds 32Mb. Increase the maximum size
of an uncompressed kernel to fix the following error:
Uncompressing Kernel Image
Error: inflate() returned -5
Image too large: increase CONFIG_SYS_BOOTM_LEN
Must RESET board to recover
arm: imx8m: imx8mm-cl-iot-gate: Add support for detect memory size
When purchasing imx8mm-cl-iot-gate it is able to customize the
memory size. It could be 1GB, 2GB and 4GB. We implement
board_phys_sdram_size() to detect the memory size for usage.
Andrey Zhizhikin [Tue, 24 Aug 2021 07:55:14 +0000 (09:55 +0200)]
tree: imx: remove old fit generator script
Since derivatives are moving to binman from usage of the FIT generator
script, and considering the warning introduced in f4a43d2925
("Makefile: Warn against using CONFIG_SPL_FIT_GENERATOR"), usage of FIT
generator is discouraged.
Current FIT generator also generates broken output, since commit 3f04db891a ("image: Check for unit addresses in FITs") prohibits using
'@' for unit addresses but the generator script still emits the old
sematics.
Remove the generator script and corresponding call in Makefile, all
derivatives should be migrated to binman in order to provide binary
images.
Since the mxs_nand_spl has implemented adjust read offset in
nand_spl_load_image, so we don't need to check the bad block in
nand_spl_adjust_offset. Directly return the offset to continue
read by nand_spl_load_image.
Ye Li [Tue, 17 Aug 2021 09:10:35 +0000 (17:10 +0800)]
arm: imx8m: Fix pad DSE issue for i.MX8MM/MN/MP
According to 8MM/MN/MP reference manual, their pad registers only have
4 valid DSE values. And DSE2 and DSE4 are different with current
definitions in iomux-v3.h. Fix the issue to align with manual.
Signed-off-by: Ye Li <ye.li@nxp.com> Acked-by: Peng Fan <peng.fan@nxp.com>
Ye Li [Tue, 17 Aug 2021 09:09:20 +0000 (17:09 +0800)]
mmc: fsl_esdhc_imx: Fix clock disable issue
The SD clock disable is wrapped by MMC_SUPPORTS_TUNING. So it
only works when UHS is enabled. However, in SD initialization the
power cycle does not depends on UHS. But the power cycle needs
disable the SD clock before power down.
So this causes a problem when UHS is not enabled. Some cards can't
become ready (ACMD14 timeout) due to the clock is enabled during
power cycle.
Signed-off-by: Ye Li <ye.li@nxp.com> Reviewed-by: Haibo Chen <haibo.chen@nxp.com> Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Heiko Schocher [Tue, 17 Aug 2021 06:17:18 +0000 (08:17 +0200)]
imx: spl: fix imx8m secure boot
cherry-picked from NXP code: 719d665a87c6: ("MLK-20467 imx8m: Fix issue for booting signed image through uuu")
which fixes secure boot on imx8m based boards. Problem was
that FIT header and so IVT header too, was loaded to
memallocated address. So the ivt header address coded
in IVT itself does not fit with the real position.
Signed-off-by: Heiko Schocher <hs@denx.de> Tested-by: Tim Harvey <tharvey@gateworks.com>
Tom Rini [Wed, 22 Sep 2021 18:50:39 +0000 (14:50 -0400)]
Convert CONFIG_NAND_OMAP_ECCSCHEME to Kconfig
The values of CONFIG_NAND_OMAP_ECCSCHEME map to the enum in
include/linux/mtd/omap_gpmc.h for valid ECC schemes. Make which one we
will use be a choice statement, enumerating the ones which we have
implemented.
Tom Rini [Wed, 22 Sep 2021 18:50:37 +0000 (14:50 -0400)]
Convert CONFIG_NAND_FSL_ELBC et al to Kconfig
This converts the following to Kconfig:
CONFIG_NAND_FSL_ELBC
CONFIG_NAND_FSL_IFC
Note that a number of PowerPC platforms had previously enabled
CONFIG_NAND_FSL_ELBC without CONFIG_MTD_RAW_NAND, and now they no longer
enable the option, reducing the size of a few functions.
Tom Rini [Wed, 22 Sep 2021 18:50:35 +0000 (14:50 -0400)]
nand.h: Cleanup linux/mtd/rawnand.h usage
We only include <linux/mtd/rawnand.h> in <nand.h> for the forward
declaration of struct nand_chip, so do that directly. Then, include
<linux/mtd/rawnand.h> where required directly.
Tom Rini [Wed, 22 Sep 2021 18:50:32 +0000 (14:50 -0400)]
Convert CONFIG_SYS_NAND_BAD_BLOCK_POS to Kconfig
This converts the following to Kconfig:
CONFIG_SYS_NAND_BAD_BLOCK_POS
In order to do this, introduce a choice for HAS_LARGE/SMALL_BADBLOCK_POS
as those are the only valid values. Use LARGE as the default as no
in-tree boards use SMALL, but it is possible.
Tom Rini [Wed, 22 Sep 2021 18:50:27 +0000 (14:50 -0400)]
m53menlo: Switch to deriving CONFIG_SYS_NAND_PAGE_COUNT
Typically platforms will define CONFIG_SYS_NAND_PAGE_COUNT based on
CONFIG_SYS_NAND_BLOCK_SIZE / CONFIG_SYS_NAND_PAGE_SIZE. Switch to this
in preparation for migrating CONFIG_SYS_NAND namespace to Kconfig.
Cc: Marek Vasut <marex@denx.de> Cc: Olaf Mandel <o.mandel@menlosystems.com> Signed-off-by: Tom Rini <trini@konsulko.com>
projects / u-boot.git / log