Chris Packham [Sat, 13 Apr 2019 08:21:48 +0000 (20:21 +1200)]
ARM: imx: Fix typo in select option for ZMX25
Correct CPU_ARM926EJS1 to CPU_ARM926EJS.
Reported-by: Robert P. J. Day <rpjday@crashcourse.ca> Signed-off-by: Chris Packham <judge.packham@gmail.com> Reviewed-by: Fabio Estevam <festevam@gmail.com>
After DM conversion, the size of U-Boot binary to increase.
Previous size is 480K after DM Conversion the new size is 557K
So it's necessary to increase the dfu request for store u-boot-dtb.img in eMMC.
This patch enable convert DM MMC for imx7d-pico board and variant.
Before the DM conversion only usdhc3 was enabled and therefore it appeared
as MMC 0 to u-boot. After enabling MMC DM though usdhc3 defaults to MMC 2,
which left unattended would drive changes to existing pico-pi bootscripts and
environment variables that rely on mmc 0.
Setup the alias of mmc0 and usdhc3 so that existing pico-imx7d boot code will
work unmodified.
When converting to DM_MMC it is necessary that SPL initializes eMMC
by itself, so move the original eMMC initialization from U-Boot
proper to SPL.
colibri-imx6ull: migrate mmc to using driver model
Migrate MMC to using driver model.
Migrate USDHC to using pinctrl.
While at it also add GPIO1_IO03__OSC32K_32K_OUT pin muxing.
While at it also update copyright period.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
colibri-imx6ull: migrate pinctrl and regulators to dtb/dm
Migrate pinctrl and regulators to device tree resp. driver model:
Ethernet, NAND and UART.
Drop BOARD_EARLY_INIT_F as it is anyway no longer used.
Enable CMD_DM, CMD_MTD, CMD_REGULATOR and DM_REGULATOR_FIXED.
While at it also update copyright period.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Drop disabling SPL_SYS_THUMB_BUILD as we anyway do not use SPL.
Enbale CRC32 verify, USB SDP and EFI loader support.
Drop CMD_GPT and disabling RANDOM_UUID.
Do savedefconfig which drops USB_FUNCTION_SDP.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Disable output driver of PAD CCM_PMIC_STBY_REQ. This prevents the
SOC to request for a lower voltage during sleep. This is necessary
because the voltage is changing too slow for the SOC to wake up
properly.
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com> Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Stefan Agner [Tue, 9 Apr 2019 15:24:10 +0000 (17:24 +0200)]
apalis/colibri_imx6/imx6ull: make sure loadaddr does not collide
Currently $loadaddr and $fdt_addr_r point to the same address. This
might be not ideal for some distro boot scripts which make use of
$loadaddr after loading the device tree.
Make sure the two variables point to two different addresses. Moving
$loadaddr is not entirly trivial since it is defined in mx6_common.h.
Move $fdt_addr_r and $ramdisk_addr_r by 1MiB, which should be enough
for scripts.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com> Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Stefan Agner [Tue, 9 Apr 2019 15:24:09 +0000 (17:24 +0200)]
colibri-imx6ull: set module variant depending on config block
Using CPU temperature grading as a discriminator if the Wi-Fi /
Bluetooth chip is populated is no longer possible due to upcoming
SKUs. Set variant to -wifi only if a valid config block is present
and the product id mentions a SKU with Wi-Fi / Bluetooth.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com> Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Stefan Agner [Tue, 9 Apr 2019 15:24:08 +0000 (17:24 +0200)]
tdx-cfg-block: simplify i.MX 6 module detection
Use CONFIG_TARGET_... at compile time to differentiate between
Apalis iMX6, Colibri iMX6 and Colibri iMX6ULL. Avoid code
duplication by moving question about Wi-Fi / Bluetooth before
IT/non-IT decision.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com> Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Marcel Ziswiler [Thu, 28 Mar 2019 22:24:50 +0000 (23:24 +0100)]
colibri_vf: fix ethernet by adding explicit phy node
The implicit fallback mechanism for searching the whole MDIO bus for at
least one PHY has been gone with the following commit b882005a18de
("drivers/net/fec: phy_init: remove redundant logic"). This lead to the
Ethernet driver erroring out as follows:
Net: Could not get PHY for FEC0: addr -19
eth-1: fec@400d1000
Colibri VFxx # dhcp
Could not get PHY for FEC0: addr -19
Could not get PHY for FEC0: addr -19
Could not get PHY for FEC0: addr -19
Could not get PHY for FEC0: addr -19
No ethernet found.
Could not get PHY for FEC0: addr -19
Colibri VFxx #
This commit adds an explicit PHY node which makes it work again.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Reviewed-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com> Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
This commit converts i.MX5's EHCI USB host driver to driver model (DM_USB).
It is a straightforward conversion (to reuse as much code as possible),
based on ehci-mx6.c code.
DTS: Enable USB host support (including regulators) on HSC|DDC boards
This commit enables the support for K&P's HSC|DDC imx53 based boards.
It was also necessary to provide device tree description for regulators
to avoid board specific code definition.
The GPIO pin description responsible for VBUS control has been moved from
"hog" group to usbh1 dedicated one.
DTS: Provide USB host DTS description for i.MX53 devices
This code has been ported from Linux kernel - tag v5.1-rc2.
The difference from the kernel is the removal of:
fsl,usbmisc = <&usbmisc 1>;
fsl,usbphy = <&usbphy1>;
properties, which are not needed for correct u-boot operation (as PHY
setup is done in ehci-mx5.c file itself).
Adam Ford [Thu, 11 Apr 2019 18:44:59 +0000 (13:44 -0500)]
ARM: imx6q_logic: Allow storing environment in FAT on eMMC
Some variations of the imx6q_logic board have eMMC instead of
NAND. Rather than creating a separate defconfig, this patch
adds the ability to read/write to eMMC (mmc 0:1) when NAND
doesn't exist.
Adam Ford [Thu, 11 Apr 2019 18:46:09 +0000 (13:46 -0500)]
ARM: imx6q_logic: Allow optional arguments to cmd line
This adds an extra, optional environmental variable called
'optargs' which if enabled allow additional parameters to be
passed to the kernel (ie, quiet, cma=128M, etc.)
Each script that setups the bootargs will just append this.
Tom Rini [Wed, 24 Apr 2019 13:04:23 +0000 (09:04 -0400)]
Merge branch '2019-04-22-master-imports'
- Add and enable brcmnand driver on a number of relevant platforms.
Also add and enable LED drivers on more bcm platforms.
- Various ARMv8 fixes/improvements, including extending PSCI
functionality.
- fs_loader improvments
- Various FIT/SPL improvements
- PCI bugfixes
- Poplar platform ethernet support
- MediaTek MMC improvements
- Android boot improvements
According to Android image format [1], kernel image resides at 1 page
offset from the boot image address. Grab the magic number from there
and allow U-Boot to handle LZ4-compressed KNL binaries instead of
hardcoding compression type to IH_COMP_NONE. Other compression types,
if needed, can be added later.
Tested on H3ULCB-KF using the image detailed in [2].
[1] Excerpt from include/android_image.h
+-----------------+
| boot header | 1 page
+-----------------+
| kernel | n pages
+-----------------+
| ramdisk | m pages
+-----------------+
| second stage | o pages
+-----------------+
Lars Povlsen [Thu, 4 Apr 2019 12:38:50 +0000 (14:38 +0200)]
ARMv8: PSCI: Fix PSCI_TABLE relocation issue
This fixes relaction isses with the PSCI_TABLE entries in
the psci_32_table and psci_64_table.
When using 32-bit adress pointers relocation was not being applied to
the tables, causing PSCI handlers to point to the un-relocated code
area. By using 64-bit data relocation is properly applied. The
handlers are thus in the "secure data" area, which is protected by
/memreserve/ in the FDT.
Signed-off-by: Lars Povlsen <lars.povlsen@microchip.com>
Trent Piepho [Wed, 27 Mar 2019 23:50:09 +0000 (23:50 +0000)]
bootm: Simplying cache flush code
The cache flush of the kernel load area needs to be aligned outward to
the DMA cache alignment. The operations are simpler if we think of this
as aligning the start down, ALIGN_DOWN(load, ARCH_DMA_MINALIGN), and
aligning the end up, ALIGN(load_end, ARCH_DMA_MINALIGN), and then find
the length of the flushed region by subtracting the former from the
latter.
Cc: Tom Rini <trini@konsulko.com> Cc: Simon Glass <sjg@chromium.org> Cc: Bryan O'Donoghue <bryan.odonoghue@linaro.org> Signed-off-by: Trent Piepho <tpiepho@impinj.com> Reviewed-by: Simon Glass <sjg@chromium.org>
malloc: Fix memalign not honoring alignment prior to full malloc init
When using memalign() in a scenario where U-Boot is configured for full
malloc support with simple malloc not explicitly enabled and before the
full malloc support is initialized, a memory block is being allocated
and returned without the alignment parameter getting honored.
Fix this issue by replacing the existing memalign pre-full malloc init
logic with a call to memalign_simple() this way ensuring proper alignment
of the returned memory block.
Fixes: ee038c58d519 ("malloc: Use malloc simple before malloc is fully initialized in memalign()") Signed-off-by: Andreas Dannenberg <dannenberg@ti.com> Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Stefan Roese [Tue, 26 Mar 2019 12:04:00 +0000 (13:04 +0100)]
spl: spl_nand.c: Add NAND loading message
This patch adds a short message to the SPL NAND loader, which displays
the source and destinations addresses including the size of the
loaded image, like this:
U-Boot SPL 2019.04-rc3-00113-g486efd8aaf (Mar 15 2019 - 14:18:02 +0100)
Trying to boot from NAND
Loading U-Boot from 0x00040000 (size 0x000a0000) to 0x22900000
I find this message quite helpful - hopefully others do so as well.
Signed-off-by: Stefan Roese <sr@denx.de> Cc: Heiko Schocher <hs@denx.de> Cc: Tom Rini <trini@konsulko.com> Reviewed-by: Tom Rini <trini@konsulko.com>
Shawn Guo [Wed, 20 Mar 2019 07:32:41 +0000 (15:32 +0800)]
poplar: enable Ethernet driver support
The 'phy' reset of gmac device in kernel device tree is not generic
enough for u-boot to use, so we need to overwrite the 'resets' property
as needed. With this device tree fixup and poplar_defconfig changes,
Ethernet starts working on Poplar board.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Shawn Guo [Wed, 20 Mar 2019 07:32:40 +0000 (15:32 +0800)]
net: add higmacv300 Ethernet driver for HiSilicon platform
It adds the driver for HIGMACV300 Ethernet controller found on HiSilicon
SoCs like Hi3798CV200. It's based on a downstream U-Boot driver, but
quite a lot of code gets rewritten and cleaned up to adopt driver model
and PHY API.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Shawn Guo [Wed, 20 Mar 2019 07:32:39 +0000 (15:32 +0800)]
reset: add reset driver for HiSilicon platform
It adds a Driver Model compatible reset driver for HiSlicon platform.
The driver implements a custom .of_xlate function, and uses .data field
as reset register offset and .id field as bit shift.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Thierry Reding [Fri, 15 Mar 2019 15:32:33 +0000 (16:32 +0100)]
pci: Scale MAX_PCI_REGIONS based on CONFIG_NR_DRAM_BANKS
If a platform defines CONFIG_NR_DRAM_BANKS, each DRAM bank will be added
as a PCI region. The number of MAX_PCI_REGIONS therefore needs to scale
with the number of DRAM banks, otherwise we will end up with too little
space in the hose->regions array to store all system memory regions.
Signed-off-by: Thierry Reding <treding@nvidia.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Thierry Reding [Fri, 15 Mar 2019 15:32:32 +0000 (16:32 +0100)]
pci: Add boundary check for hose->regions
Make sure that we don't overflow the hose->regions array, otherwise we
would end up overwriting the hose->region_count field and cause mayhem
to ensue. Also print an error message when we'd be overflowing because
it indicates that there aren't enough regions available and the number
needs to be increased.
Signed-off-by: Thierry Reding <treding@nvidia.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Ibai Erkiaga [Fri, 15 Mar 2019 12:18:41 +0000 (12:18 +0000)]
arm: arm64 32bit address relocation
Current relocation code is limited to 21bit PC-relative addressing
which might not be enough for bigger code sizes. The following patch
increases the addressing to 32bit PC-relative. This feature is
specially interesting if U-Boot is build without optimiation (-O0) as
the text section is increased significativelly.
Signed-off-by: Ibai Erkiaga <ibai.erkiaga-elorza@xilinx.com>
Marek Vasut [Thu, 14 Mar 2019 00:01:24 +0000 (01:01 +0100)]
travis: Add srecord package
At least MIPS Boston currently uses srec_cat tool to fiddle with
srecords. There will be other platforms coming, so install the
tool to prevent build problems.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com> Cc: Michal Simek <michal.simek@xilinx.com> Cc: Tom Rini <trini@konsulko.com>
Stefano Babic [Wed, 13 Mar 2019 08:46:45 +0000 (09:46 +0100)]
Add target to generate initial environment
The initial environment is linked to the u-boot binary. Modifying the
environment from User Space with the env tools requires that the tools
are always built together with the bootloader to be sure that they
contain the initial environment in case no environment is stored into
persistent storage or when a board boots with just the default
environment. This makes difficult for distros to provide a general
package to access the environment. A simpler way is if the tools are
generic for all boards and a configuration file is given to provide the
initial environment.
The patch just generates the initial environment by extracting it from
the compiled object. This file can then be used for tools in user space
to initialize the environment.
Marek Vasut [Wed, 6 Mar 2019 21:04:31 +0000 (22:04 +0100)]
spl: ymodem: Add support for loading full fitImages
Add support for loading fully featured fitImages over YModem in SPL.
This is useful when various advanced features of full fitImages are
needed in SPL.
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Tom Rini <trini@konsulko.com>
Tien Fong Chee [Tue, 5 Mar 2019 15:29:38 +0000 (23:29 +0800)]
misc: fs_loader: Replace label with DT phandle
In previously label which will be expanded to the node's full path was
used, and now replacing label with most commonly used DT phandle. The
codes were changed accordingly to the use of DT phandle and supporting
multiple instances.
Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
Ibai Erkiaga [Mon, 25 Feb 2019 10:11:45 +0000 (10:11 +0000)]
arm: fix hvc call
HVC call makes use of 6 mandatory arguments rather than 7 in the same way
as SMC calls. The 7th argument is optional (Client ID) for both HVC and
SMC but is implemented as 16-bit parameter and register R7 or W7. The aim
of this patch is just fix compilation error due to an invalid asm code in
the HVC call so that's why the 7th argument is removed.
The issue does not report any error in a normal build as hvc_call is not
used at all and is optimized by the compiler. Using -O0 triggers the
error so the patch is intended to fix issues on a ongoing effor to build
U-Boot with -O0.
Signed-off-by: Ibai Erkiaga <ibai.erkiaga-elorza@xilinx.com>
Shawn Guo [Fri, 22 Feb 2019 08:28:06 +0000 (16:28 +0800)]
Support boot Android image without address on bootm command
It works perfectly fine to boot an Android boot.img with bootm command
followed by an explicit address argument that holds the image. But if
we have boot.img downloaded into default 'loadaddr', and then boot it
using bootm command without the address argument, we will run into
problem, because U-Boot fails to find ramdisk and fdt (second area) in
boot.img.
The current Android image support assumes there is always an address
argument on bootm command. However just like booting any other images,
'loadaddr' should be used when address argument is missing from bootm
command. It patches boot_get_ramdisk() and boot_get_fdt() a bit to
support this quite common usage of bootm command for Android image.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org> Reviewed-by: Tom Rini <trini@konsulko.com>
projects / u-boot.git / log