Hou Zhiqiang [Fri, 5 Feb 2021 08:34:02 +0000 (16:34 +0800)]
configs: T1042: Drop the CONFIG_VIDEO
Drop the CONFIG_VIDEO to fix the following build warning.
===================== WARNING ======================
This board does not use CONFIG_DM_VIDEO Please update
the board to use CONFIG_DM_VIDEO before the v2019.07 release.
UPD include/generated/dt.h
Failure to update by the deadline may result in board removal.
See doc/driver-model/migration.rst for more info.
UPD include/generated/timestamp_autogenerated.h
====================================================
Hou Zhiqiang [Fri, 5 Feb 2021 07:45:12 +0000 (15:45 +0800)]
armv7: ls102xa: Enable I-Cache to speed up the boot time
Enable the I-Cache to speed up the boot time, especailly for the NOR
boot, currently it takes about 15 seconds from power up to the U-Boot
prompt, and with the I-Cache enabled it only takes around 2.5 seconds.
LX2162A is not like LX2160A which has different PCIe controller
in rev1 and rev2 silicon. It supports only one configuration of
PCIe controller, which is same as LS2088A. So update PCIe
compatible string same as LS2088A.
Mathew McBride [Mon, 25 Jan 2021 03:55:22 +0000 (03:55 +0000)]
spi: fsl_qspi: apply the same settings for LS1088 as LS208x
The LS1088 requires the same QUADSPI_QURIK_BASE_INTERNAL
workaround as the LS208x and also has a 64 byte TX buffer.
With the previous settings SPI-NAND reads over AHB were
corrupted.
Fixes: 91afd36f3802 ("spi: Transform the FSL QuadSPI driver to use the SPI MEM API") Signed-off-by: Mathew McBride <matt@traverse.com.au> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Mathew McBride [Mon, 25 Jan 2021 03:55:21 +0000 (03:55 +0000)]
spi: fsl_qspi: Ensure width is respected in spi-mem operations
Adapted from kernel commit b0177aca7aea
From: Michael Walle <michael@walle.cc>
Make use of a core helper to ensure the desired width is respected
when calling spi-mem operators.
Otherwise only the SPI controller will be matched with the flash chip,
which might lead to wrong widths. Also consider the width specified by
the user in the device tree.
Fixes: 91afd36f38 ("spi: Add a driver for the Freescale/NXP QuadSPI controller") Signed-off-by: Michael Walle <michael@walle.cc> Link: https://lore.kernel.org/r/20200114154613.8195-1-michael@walle.cc Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Mathew McBride <matt@traverse.com.au> [adapt for U-Boot] Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Niel Fourie [Thu, 21 Jan 2021 12:19:18 +0000 (13:19 +0100)]
PowerPC: dts: Pulled in kmcent2 dts files from Linux 5.10
Pulled in the kmcent2.dts and all its dependents from Linux 5.10,
commit 2c85ebc57b3e upstream. Replaced the license text with
SPDX License Identifiers.
Take into account SDRAM_BASE address when calculating pnvramaddr and
varaddr offsets.
Up to now Keymile designs had SDRAM_BASE equal to zero and the offsets
where calculated correctly, this fix is for the upcoming designs that
have SDRAM_BASE different then zero.
Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachi-powergrids.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
keymile: common: qrio: print QRIO id and revision number
Add show_qrio function to print chip id and revision information.
There are already multiple QRIOÂ chip versions available and the upcoming
designs may want to show used version.
board: keymile: common: fix qrio compilation for arm
This patch is fixing qrio driver compilation for ARM architecture:
- It includes asm/io.h for in_/out_ access
- It use correct names for set/clear_bits as defined in linux/bitops.h
Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachi-powergrids.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Michael Walle [Thu, 7 Jan 2021 23:08:59 +0000 (00:08 +0100)]
board: sl28: add SATA support
Enable SATA support. Although not supported by the usual SATA pins on
the SMARC baseboard connector, SATA mode is supported on a PCIe lane.
This way one can use a mSATA card in a Mini PCI slot.
We need to invert the received data because in this mode the polarity of
the SerDes lane is swapped. Provide a fixup in board_early_init_f() for
the SPL. board_early_init_f() is then not common between SPL and u-boot
proper anymore, thus common.c is removed, as it just contained said
function.
Signed-off-by: Michael Walle <michael@walle.cc> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Michael Walle [Thu, 7 Jan 2021 23:08:58 +0000 (00:08 +0100)]
board: sl28: add network variant 2 support
Although this variant has two external network ports, they are not (yet)
supported by the bootloader because they are connected via an internal
network switch. Otherwise its the same as the other variants.
Signed-off-by: Michael Walle <michael@walle.cc> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Michael Walle [Thu, 7 Jan 2021 23:08:57 +0000 (00:08 +0100)]
board: sl28: add network variant 1 support
This variant has one network port connected via RGMII and doesn't have
any TSN capabilities out-of-the-box. Instead it has all four SerDes
lanes available for customer use.
Signed-off-by: Michael Walle <michael@walle.cc> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Michael Walle [Thu, 7 Jan 2021 23:08:56 +0000 (00:08 +0100)]
board: sl28: move ethernet aliases to variant specific dtsi
The variants differ in their network configuration. Move the first two
network aliases to the proper variant device tree includes. This is in
prepartion for variant 1 and 2 support which has a different network
port mapping. The network aliases for the two internal ports will stay
in the common dtsi because they are present on all board variants.
This might leave a hole if there is no ethernet1 alias. This is
intended.
Signed-off-by: Michael Walle <michael@walle.cc> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Biwen Li [Thu, 10 Dec 2020 03:02:47 +0000 (11:02 +0800)]
configs: ls1088aqds: add COMMON_ENV to fix distroboot
Add COMMON_ENV(kernelheader_addr_r, fdtheader_addr_r,
kernel_addr_r, fdt_addr_r, load_addr)
to fix a bug that failed to boot to ubuntu
Failed log as follows,
## Executing script at 80000000
load - load binary file from a filesystemUsage:
load <interface> [<dev[:part]> [<addr> [<filename> [bytes [pos]]]]]
- Load binary file filename from partition part on device
type interface instance dev to address addr in memory.
bytes gives the size to load in bytes.
If bytes is 0 or omitted, the file is read until the end.
pos gives the file byte position to start reading from.
If pos is 0 or omitted, the file is read from the start.
...
Bad Linux ARM64 Image magic!
SCRIPT FAILED: continuing...
Signed-off-by: Biwen Li <biwen.li@nxp.com>
[Updated description] Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Ioana Ciornei [Wed, 9 Dec 2020 11:31:58 +0000 (13:31 +0200)]
net: memac_phy: add a timeout to MDIO operations
We have encountered circumstances when a board design does not include
pull-up resistors on the external MDIO buses which are not used. This
leads to the MDIO data line not being pulled-up, thus the MDIO controller
will always see the line as busy.
Without a timeout in the MDIO bus driver, the execution is stuck in an
infinite loop when any access is initiated on that external bus.
Add a timeout in the driver so that we are protected in this
circumstance. This is similar to what is being done in the Linux
xgmac_mdio driver.
Michael Walle [Wed, 9 Dec 2020 09:53:26 +0000 (10:53 +0100)]
board: kontron: disable flash unlock all
Although the status register is protected by the hardware write
protection, there is a hardware jumper to disable that hardware write
protection. Thus if a user would set this jumper any u-boot start would
disable the write protection altogether.
Circumvent that by not disabling the write protection in the first
place.
Signed-off-by: Michael Walle <michael@walle.cc> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Michael Walle [Wed, 9 Dec 2020 09:53:25 +0000 (10:53 +0100)]
mtd: spi-nor: add unlock all config option
Provide an explicit configuration option to disable default "unlock all"
of any flash chip which supports locking. It doesn't make sense to
automatically unprotect the entire flash on each u-boot startup if the
block protection bits are actually used.
Traditionally, the unlock was there to be able to write to flash devices
which powered-up with the block protection bits set. Over time this
feature creeped into all flash devices which support locking.
For a more detailed description and discussion see:
https://lore.kernel.org/linux-mtd/20201203162959.29589-8-michael@walle.cc/
Keep things simple in u-boot and just provide a configration option to
disable this behavior which can be set per board.
Signed-off-by: Michael Walle <michael@walle.cc> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Adam Ford [Wed, 3 Feb 2021 12:57:20 +0000 (06:57 -0600)]
ARM: rmobile: Add Beacon EmbeddedWorks RZG2H Dev Kit
The Beacon EmbeddedWorks kit is based on the R8A774E1 SoC also
known as the RZ/G2H.
The kit consists of a SOM + Baseboard and supports microSD,
eMMC, Ethernet, a couple celular radios, two CAN interfaces,
Bluetooth and WiFi. It shares much of the same design as
the RZ/G2M and RZ/G2N dev kits.
Adam Ford [Wed, 3 Feb 2021 12:57:19 +0000 (06:57 -0600)]
ARM: rmobile: Add Beacon EmbeddedWorks RZG2N Dev Kit
The Beacon EmbeddedWorks kit is based on the R8A774B1 SoC also
known as the RZ/G2N.
The kit consists of a SOM + Baseboard and supports microSD,
eMMC, Ethernet, a couple celular radios, two CAN interfaces,
Bluetooth and WiFi. It shares much of the same design as
the RZ/G2M dev kit.
Adam Ford [Wed, 3 Feb 2021 12:57:15 +0000 (06:57 -0600)]
dt-bindings: Sync versaclock.h with upcoming 5.12-rc1
The versaclock doesn't have a driver yet, but there are a bunch
of device tree updates for the Beacon RZ/G2 boards that won't
compile without these. A driver is coming, so sync the bindings
for now
fastboot: reinit partition after storing GPT or MBR
In case MMC has MBR system and fastboot writes GPT,
MMC is still recognized as MBR.
Invoke part_init() to purge cached data and update
information about partition table type.
Signed-off-by: Roman Stratiienko <r.stratiienko@gmail.com>
Patrick Delaunay [Wed, 27 Jan 2021 13:46:49 +0000 (14:46 +0100)]
fastboot: add command to select the eMMC boot configuration
Add command oem bootbus which executes the command
``mmc bootbus <id> <arg>`` on the current fastboot mmc device
(<i> = CONFIG_FASTBOOT_FLASH_MMC_DEV) to set the eMMC boot
configuration on first update, with
<arg> = boot_bus_width reset_boot_bus_width boot_mode
Patrick Delaunay [Wed, 27 Jan 2021 13:46:48 +0000 (14:46 +0100)]
fastboot: add command to select the default emmc hwpart for boot
Add fastboot command oem partconf which executes the command
``mmc partconf <id> <arg> 0`` on the current <id> mmc device
to configure the eMMC boot partition with
<arg>: boot_ack boot_partition, so the command is:
Split userdata and boot partition support for eMMC update
and correct the description (update is supported).
The new configuration CONFIG_FASTBOOT_MMC_USER_SUPPORT
allows to activate support of userdata partition update,
based on target name=CONFIG_FASTBOOT_MMC_USER_NAME
This patch also removes the unnecessary dependency with
ARCH_MEDIATEK and EFI_PARTITION.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
It is possible to implement fastboot_set_reboot_flag in a generic way
if BCB commands are turned on for a target. Using
bcb_set_reboot_reason allows to do this by simply passing string with
correct reboot reason that should be handled during next boot process.
If BCB are turned off, then bcb_set_reboot_reason would simply return
error, so it won't introduce any new behaviour for such targets.
Signed-off-by: Roman Kovalivskyi <roman.kovalivskyi@globallogic.com>
Current generic implementation of fastboot_set_reboot_flag is somewhat
messy and requires some additional configuration option to be enabled
besides CMD_BCB, so it reverts that implementtion in order to bring a
new cleaner one.
Next commit introduces new generic implementation of
fastboot_set_reboot_flag.
Signed-off-by: Roman Kovalivskyi <roman.kovalivskyi@globallogic.com>
- introduces some standard sysinfo options as a source, e.g. to read
strapping pins to determine the board revision
- allows the U-Boot version number to be included
- allows the version number to be provided programmatically, e.g. to
support the build system adding information after U-Boot is built
Simon Glass [Fri, 5 Feb 2021 04:17:22 +0000 (21:17 -0700)]
x86: coral: Add sysinfo ops
These ops are missing at present which is not permitted. Add an empty
operation struct.
Note: If the uclass requires operations then the drivers should provide
them. Otherwise, checking for missing operations must be done in every
uclass operation, so it adds to code size.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Fri, 5 Feb 2021 04:17:21 +0000 (21:17 -0700)]
sysinfo: Move #ifdef so that operations are always defined
At present the struct is not available unless SYSINFO is enabled. This is
annoying since code it is not possible to use compile-time checks like
CONFIG_IS_ENABLED(SYSINFO) with this header.
Fix it by moving the #ifdef.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Fri, 5 Feb 2021 04:17:20 +0000 (21:17 -0700)]
smbios: Add more options for the BIOS version string
At present the version string is obtained from PLAIN_VERSION. Some boards
may want to configure this using the device tree, since the build system
can more easily insert things there after U-Boot itself is built. Add this
option to the code.
Also in some cases the version needs to be generated programmatically,
such as when it is stored elsewhere in the ROM and must be read first.
To handle this, keep a pointer around so that it can be updated later.
This works by storing the last string in the context, since it is easier
than passing out a little-used extra parameter.
Provide a function to update the version string.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Fri, 5 Feb 2021 04:17:18 +0000 (21:17 -0700)]
smbios: Drop the eos parameter
We can store this in the context and avoid passing it to each function.
This makes it easier to follow and will also allow keeping track of the
end of the string table (in future patches).
Add an 'eos' field to the context and create a function to set it up.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Fri, 5 Feb 2021 04:17:17 +0000 (21:17 -0700)]
smbios: Use a struct to keep track of context
At present we pass the ofnode to each function. We also pass the 'eos'
pointer for adding new strings. We don't track the current end of the
string table, so have smbios_string_table_len() to find that.
The code can be made more efficient if it keeps information in a
context struct. This also makes it easier to add more features.
As a first step, switch the ofnode parameter to be a context pointer.
Update smbios_add_prop() at the same time to avoid changing the same
lines of code in consecutive patches.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Fri, 5 Feb 2021 04:17:13 +0000 (21:17 -0700)]
Makefile: Provide numeric versions
For SMBIOS we want to store the numeric version numbers in the tables. It
does not make sense to parse the strings. Instead, add new #defines with
the version and patchlevel.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tom Rini [Fri, 5 Feb 2021 14:39:31 +0000 (09:39 -0500)]
Merge tag 'ti-v2021.04-rc2' of https://gitlab.denx.de/u-boot/custodians/u-boot-ti
- Sync DTS from Linux kernel for all K3 platforms
- Add MMC higher speed nodes for AM65x, J721e, J7200
- Convert Nokia RX-51 to use CONFIG_DM_MMC
- Minor fixes for LEGO MINDSTORMS
Tom Rini [Thu, 4 Feb 2021 22:35:50 +0000 (17:35 -0500)]
Merge tag 'efi-2021-04-rc2' of https://gitlab.denx.de/u-boot/custodians/u-boot-efi
Pull request for UEFI sub-system for efi-2021-04-rc2
Bug fixes:
* do not allow creating of files with filenames on FAT file system
* install UEFI System Partition GUID on ESP handle
* in dtbdump.efi test tool use GUID to find ESP handle
Documentation:
* man-page for load command
* describe end of life of plat_auto
The Load File2 protocol exposes a device path with a VenMedia() node. Hence
our implementation of the device path to text protocol should support this
node.
Cc: Ilias Apalodimas <ilias.apalodimas@linaro.org> Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
If dtbdump.efi is loaded from memory when calling LoadImage the loaded
image protocol will not indicate the partition from where it was loaded.
In this case use the EFI system partition for the 'load' and 'save'
commands.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
efi_loader: only check size if EFI_DT_APPLY_FIXUPS
In the implementation of the EFI_DT_FIXUP_PROTOCOL:
* Only check the buffer size when EFI_DT_APPLY_FIXUPS is set.
* In this case the field totalsize of the device-tree may not exceed the
buffer size.
* Install device-tree only if EFI_DT_INSTALL_TABLE is set.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
projects / u-boot.git / log