Stephen Warren [Thu, 24 Apr 2014 23:52:40 +0000 (17:52 -0600)]
usb: ums: use only 1 buffer for CI_UDC
ci_udc.c allocates only a single buffer for each endpoint, which
ci_ep_alloc_request() returns as a hard-coded value rather than
dynamically allocating. Consequently, storage_common.c must limit
itself to using a single buffer at a time. Add a special case
to the definition of FSG_NUM_BUFFERS for this.
Another option would be to fix ci_ep_alloc_request() to dynamically
allocate the buffers like some/all(?) other device mode drivers do.
However, I don't think that ci_ep_queue() supports queueing up
multiple buffers either yet, and I'm not familiar enough with the
controller yet to implement that. As such, any attempt to use multiple
buffers simply results in data corruption and other errors.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Stephen Warren [Thu, 24 Apr 2014 23:52:39 +0000 (17:52 -0600)]
usb: ci_udc: support variants with hostpc register
Tegra's USB controller appears to be a variant of the ChipIdea
controller; perhaps derived from it, or simply a different version of
the IP core to what U-Boot supports today.
In this variant, at least the following difference are present:
- Some registers are moved about.
- Setup transaction completion is reported in a separate 'epsetupstat'
register, rather than in 'epstat' (which still exists, perhaps for
other transaction types).
- USB connection speed is reported in a separate 'hostpc1_devlc'
register, rather than 'portsc'.
- The registers used by ci_udc.c begin at offset 0x130 from the USB
register base, rather than offset 0x140. However, this is handled
by the associated EHCI controller driver, since the register address
is stored in controller.ctrl->hcor.
Introduce define CONFIG_CI_UDC_HAS_HOSTPC to indicate which variant of
the controller should be supported. The "HAS_HOSTPC" part of this name
mirrors the similar "has_hostpc" field used by the Linux EHCI controller
core to represent the presence/absence of the hostpc1_devlc register.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Stephen Warren [Thu, 24 Apr 2014 23:52:38 +0000 (17:52 -0600)]
usb: ci_udc: make PHY initialization conditional
usb_gadget_register_driver() currently unconditionally programs PORTSC
to select a ULPI PHY. This is incorrect on at least the Tegra boards I
am testing with, which use a UTMI PHY for the OTG ports. Make the PHY
selection code conditional upon the specific EHCI controller that is in
use.
Ideally, I believe that the PHY initialization code should be part of
ehci_hcd_init() in the relevant EHCI controller driver, or some board-
specific function that ehci_hcd_init() calls.
For MX6, I'm not sure this PHY initialization code is correct even before
this patch, since ehci-mx6's ehci_hcd_init() already configures PORTSC to
a board-specific value, and it seems likely that the code in ci_udc.c is
incorrectly undoing this. Perhaps this is not an issue if the PHY
selection register bits aren't implemented on this instance of the MX6
USB controller?
ehci-mxs.c doens't appear to touch PORTSC, so this code is likely still
required there.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Stephen Warren [Thu, 24 Apr 2014 23:52:37 +0000 (17:52 -0600)]
usb: ci_udc: set ep->req.actual after transfer
At least drivers/usb/gadget/storage_common.c expects that ep->req.actual
contain the number of bytes actually transferred. (At least in practice,
I observed it failing to work correctly unless this was the case).
However, ci_udc.c modifies ep->req.length instead. I assume that .length
is supposed to represent the allocated buffer size, whereas .actual is
supposed to represent the actual number of bytes transferred. In the OUT
transaction case, this may happen simply because the host sends a smaller
packet than the max possible size, which is quite legal. In the IN case,
transferring fewer bytes than requested could presumably happen as an
error.
Modify handle_ep_complete() to write to .actual rather than modifying
.length.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Stephen Warren [Thu, 24 Apr 2014 23:52:36 +0000 (17:52 -0600)]
usb: ci_udc: Support larger packets
ci_ep_queue() currently only fills in the page0/page1 fields in the
queue item. If the buffer is larger than 4KiB (unaligned) or 8KiB
(page-aligned), then this prevents the HW from knowing where to write
the balance of the data.
Fix this by initializing all 5 pageN pointers, which allows up to
16KiB (potentially non-page-aligned) buffers.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
exynos: usb: Fix data abort on boards w/o vbus-gpio node in the DT
Commit 4a271cb1b4ff doesn't take into account that fdtdec_setup_gpio()
returns success when the gpio passed to it is FDT_GPIO_NONE (no
gpio node found in the fdtdec_decode_gpio() call). This results in
calling gpio_direction_output() on invalid gpio. For this reason
executing "usb start" command on Arndale causes data abort in the
ehci-exynos driver.
Add the fdt_gpio_isvalid() check to fix that problem.
Signed-off-by: Andrey Konovalov <andrey.konovalov@linaro.org> Cc: Julius Werner <jwerner@chromium.org> Cc: Simon Glass <sjg@chromium.org> Cc: Minkyu Kang <mk7.kang@samsung.com> Cc: Marek Vasut <marex@denx.de>
Rob Herring [Fri, 18 Apr 2014 13:54:30 +0000 (08:54 -0500)]
usb: musb: fill in usb_gadget_unregister_driver
Add missing missing disconnect and unbind calls to the musb gadget driver's
usb_gadget_unregister_driver function. Otherwise, any gadget drivers fail
to uninitialize and run a 2nd time.
usb:gadget:f_thor: fix write to filesystem by add dfu_flush()
Since dfu read/write operations needs to be flushed manually,
writing to filesystem on MMC by thor was broken. MMC raw write
actually is working fine because current dfu_flush() function
writes filesystem only. This commit adds dfu_flush() to f_thor
and now filesystem write is working.
This change was tested on Trats2 board.
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com> Cc: Lukasz Majewski <l.majewski@samsung.com> Cc: Marek Vasut <marex@denx.de> Cc: Heiko Schocher <hs@denx.de> Cc: Tom Rini <trini@ti.com>
usb:gadget:f_thor: code cleanup in function download_tail()
In thor's download_tail() function, dfu_get_entity() is called
before each dfu_write() call and the returned entity pointers
are the same. So dfu_get_entity() can be called just once and
this patch changes this.
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com> Cc: Lukasz Majewski <l.majewski@samsung.com> Cc: Marek Vasut <marex@denx.de> Cc: Heiko Schocher <hs@denx.de> Cc: Tom Rini <trini@ti.com>
Adrian Cox [Thu, 10 Apr 2014 13:02:44 +0000 (14:02 +0100)]
usb: Fix USB keyboard polling via control endpoint
USB keyboard polling failed for some keyboards on PowerPC 5020.
This was caused by requesting only 4 bytes of data from keyboards that
produce an 8 byte HID report.
Signed-off-by: Adrian Cox <adrian@humboldt.co.uk> Signed-off-by: Wolfgang Denk <wd@denx.de> Cc: Marek Vasut <marex@denx.de>
drivers/i2c/fsl_i2c: modify i2c_read to handle multi-byte write
Most of the I2C slaves support accesses in the typical style
that is : read/write series of bytes at particular address offset.
These transactions look like:"
(1) START:Address:Tx:Offset:RESTART:Address[0..4]:Tx/Rx:data[0..n]:STOP"
However there are certain devices which support accesses in
terms of the transactions as follows:
(2) "START:Address:Tx:Txdata[0..n1]:Clock_stretching:
RESTART:Address:Rx:data[0..n2]"
Here Txdata is typically a command and some associated data,
similarly Rxdata could be command status plus some data received
as a response to the command sent.
Type (1) transactions are currently supportd in the
i2c driver using i2c_read and i2c_write APIs. I2C EEPROMs,
RTC, etc fall in this category.
To handle type (2) along with type (1) transactions,
i2c_read() function has been modified.
York Sun [Mon, 10 Feb 2014 22:02:52 +0000 (14:02 -0800)]
driver/mxc_i2c: Move static data structure to global_data
This driver needs a data structure in SRAM before SDRAM is available.
This is not alway the case using .data section. Moving this data
structure to global_data guarantees it is writable.
Signed-off-by: York Sun <yorksun@freescale.com> CC: Troy Kisky <troy.kisky@boundarydevices.com>
Add support of 2 stage NAND/SD boot loader using SPL framework.
PBL initialise the internal SRAM and copy SPL, this further
initialise DDR using SPD and environment and copy u-boot from
NAND/SD to DDR, finally SPL transfer control to u-boot.
NOR uses CS1 instead of CS2 when NAND boot, fix it.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
Shengzhou Liu [Fri, 18 Apr 2014 08:43:41 +0000 (16:43 +0800)]
board/t2080rdb: some update for t2080rdb
- update readme.
- add CONFIG_SYS_CORTINA_FW_IN_* for loading Cortina PHY CS4315
ucode from NOR/NAND/SPI/SD/REMOTE.
- update cpld vbank with SW3[5:7]=000 as default vbank0 instead of
previous SW3[5:7]=111 as default vbank.
- fix CONFIG_SYS_I2C_EEPROM_ADDR_LEN to 2.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
Shengzhou Liu [Fri, 18 Apr 2014 08:43:40 +0000 (16:43 +0800)]
board/t208xrdb: Add support of 2-stage NAND/SPI/SD boot
Add support of 2-stage NAND/SPI/SD boot loader using SPL framework.
PBL initializes the internal CPC-SRAM and copy SPL(160K) to it,
SPL further initializes DDR using SPD and environment and copy
u-boot(768K) from SPI/SD/NAND to DDR, finally SPL transfers control
to u-boot.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
Shengzhou Liu [Fri, 18 Apr 2014 08:43:39 +0000 (16:43 +0800)]
board/t208xqds: Add support of 2-stage NAND/SPI/SD boot
Add support of 2-stage NAND/SPI/SD boot loader using SPL framework.
PBL initializes the internal CPC-SRAM and copy SPL(160K) to it,
SPL further initializes DDR using SPD and environment and copy
u-boot(768 KB) from SPI/SD/NAND to DDR, finally SPL transfers
control to u-boot.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
[York Sun: fix boards.cfg for T2081QDS_SDCARD and _SPIFLASH] Reviewed-by: York Sun <yorksun@freescale.com>
powerpc/mpc85xx: Add Differential SYSCLK config support T1040
Adds support for clock sourcing from sysclk(100MHz) for usb
on T104xRDB and T1040QDS. This requires changing reference divisor
and multiplication factor to derive usb clock from sysclk.
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
vijay rai [Tue, 15 Apr 2014 06:04:12 +0000 (11:34 +0530)]
powerpc/85xx: Enhance get_sys_info() to check clocking mode
T1040 and it's variants provide "Single Oscillator Source" Reference Clock Mode.
In this mode, single onboard oscillator(DIFF_SYSCLK) can provide the reference clock
(100MHz) to the following PLLs:
• Platform PLL
• Core PLLs
• USB PLL
• DDR PLL, etc
The cfg_eng_use0 of porsr1 register identifies whether the SYSCLK (single-ended) or
DIFF_SYSCLK (differential) is selected as the clock input to the chip.
get_sys_info has been enhanced to add the diff_sysclk so that the
various drivers can be made aware of ths diff sysclk configuration and
act accordingly.
Other changes:
-single_src to ddr_refclk_sel, as it is use for checking ddr reference clock
-Removed the print of single_src from get_sys_info as this will be
-printed whenever somebody calls get_sys_info which is not appropriate.
-Add print of single_src in checkcpu as it is called only once during initialization
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com> Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com> Signed-off-by: Vijay Rai <vijay.rai@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
Powerpc/mpc8536DS: Increase SPI/SD uboot Image size to 768K
u-boot binary size for Freescale mpc8536DS platforms is 512KB.
This has been reached to upper limit of the platforms and causig
linker error. So increase the u-boot binary size to 768KB.
Signed-off-by: Haijun Zhang <Haijun.Zhang@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
board/t104xrdb: Add support of NAND, SD, SPI boot for T104xRDB
Add support of 2 stage NAND, SD, SPI boot loader using SPL framework.
here, PBL initialise the internal SRAM and copy SPL(160KB). This further
initialise DDR using SPD and environment and copy u-boot(768 KB) from NAND to DDR.
Finally SPL transer control to u-boot.
Initialise/create followings required for SPL framework
- Add spl.c which defines board_init_f, board_init_r
- update tlb and ddr accordingly
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
board/b4qds:Add support of 2 stage NAND boot-loader
Add support of 2 stage NAND boot loader using SPL framework.
here, PBL initialise the internal SRAM and copy SPL(160KB). This further
initialise DDR using SPD and environment and copy u-boot(768 KB) from NAND to DDR.
Finally SPL transer control to u-boot.
Initialise/create followings required for SPL framework
- Add spl.c which defines board_init_f, board_init_r
- update tlb and ddr accordingly
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
driver/mtd/spi:Read 8KB data chunk during u-boot load in SPL
SPI driver perform its operation(read/write) on 64KB buffer chunk for data
greater than 64KB. This buffer chunk is allocated from system heap.
During SPL boot, 768KB of data is read from SPI flash.
Here, heap size may not be sufficient enough to full-fill 64KB buffer
requirement of SPI driver. So break down u-boot read operation at 8KB of chunk.
Also, fix a warning i.e. "unused variable buf" during CONFIG_FSL_CORENET
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
powerpc/mpc85xx:Disable non DDR LAWs before init_law
Before parsing LAW table i.e. init_law, boot loader should disable all
previous LAWs except DDR LAWs which has been created by previous
pre boot loader during DDR initialization.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
Current SPL code base has BSS section placed after reset_vector. This means
they have to relocate to use the global variables. This put an implicit
requirement of having SPL size = Memory/2.
To avoid relocation:
- Move bss_section within SPL range
- Modify relocate_code()
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
powerpc/mpc85xx: Move LAW_EN define outside of config
LAW_EN is only defined if CONFIG_SYS_CCSRBAR_DEFAULT is not equal to
CONFIG_SYS_CCSRBAR_PHYS. in SPL framework CCSRBAR is not relocated hence
both are same. This cause compilation error.
So LAW_EN define outside of configs
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
When T104x soc wakes up from deep sleep, control is passed to the
primary core that starts executing uboot. After re-initialized some
IP blocks, like DDRC, kernel will take responsibility to continue
to restore environment it leaves before.
Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
Tang Yuantian [Wed, 26 Mar 2014 08:08:05 +0000 (16:08 +0800)]
mpc85xx: Add support for the supplement configuration unit register
The supplement configuration unit (SCFG) provides chip-specific
configuration and status registers for the device. It is the chip
defined module for extending the device configuration unit (DCFG)
module. It provides a set of CCSR registers in addition to those
available in the device configuration unit.
The base address for this unit is 0x0F_C000.
Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
York Sun [Tue, 1 Apr 2014 21:20:49 +0000 (14:20 -0700)]
drivers/ddr: Fix possible out of bounds error
This is a theoretical possible out of bounds error in DDR driver. Adding
check before using array index. Also change some runtime conditions to
pre-compiling conditions.
Signed-off-by: York Sun <yorksun@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
driver/net/fm/memac_phy: Initialize mdio_clock for SoCs wih FMANv3
MDIO clock needs to be initialized in u-boot code for SoCs
having FMAN-v3(v3H or v3L) controller due to below reasons
-On SoCs that have FMAN-v3H like B4860, default value of
MDIO_CLK_DIV bits in mdio_stat(mdio_cfg) register generates
mdio clock too high (much higher than 2.5MHz), violating the
IEEE specs.
-On SOCs that have FMAN-v3L like T1040, default value of
MDIO_CLK_DIV bits is zero, so MDIO clock is disabled.
So, for proper functioninig of MDIO, MDIO_CLK_DIV bits needs to
be properly initialized.
Also this type of initialization is generally done in
PBI(pre-bootloader) phase using rcw.But for chips like T1040
which support deep-sleep, such type of initialization cannot be
done in PBI phase due to the limitation that during deep-sleep
resume, FMAN (MDIO) registers are not accessible in PBI phase.
So, mdio clock initailization must be done as part of u-boot.
This initialization code is implemented in memac_phy.c which
gets compiled only for SoCs having FMANv3, so no extra compilation
flag is required.
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
fsl/usb: Increase TXFIFOTHRESH value for usb write in T4 Rev 2.0
Increase TXFIFOTHRES field value in TXFILLTUNING register of usb for T4 Rev 2.0.
This decreases data burst rate with which data packets are posted from the TX
latency FIFO to compensate for latencies in DDR pipeline during DMA.
This avoids Tx buffer underruns and leads to successful usb writes
Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com> Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
powerpc/cpu/mpc85xx: Add MAC address for layer 2 switch
T1040RDB and T1040QDS boards have an integrated l2 switch.
The switch needs a MAC address for Layer 2 protocols
(MSTP, LLDP, LACP, etc). Setting a MAC address on l2switchaddr will add
a MAC in device-tree, under node l2switch.
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@freescale.com> Cc: York Sun <yorksun@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
vijay rai [Mon, 31 Mar 2014 06:16:34 +0000 (11:46 +0530)]
powerpc/t104xrdb: Unification of T104xRDB header files
T1040RDB, T1042RDB header files are very similar so merged into new header file T104xRDB.
T104xRDB header file can support both T1040RDB and T1042RDB_PI header.
Patch makes following changes
-Update Boards.cfg file for T1040RDB and T1042RDB_PI
-Add new T104xRDB header file
-Delete T1040RDB, T1042RDB_PI header file
Signed-off-by: Vijay Rai <vijay.rai@freescale.com> Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
Fix following compile warnings
fsl_esdhc_spl.c: In function 'mmc_boot':
fsl_esdhc_spl.c:35:10: warning: unused variable 'byte_num' [-Wunused-variable]
fsl_esdhc_spl.c:35:7: warning: unused variable 'i' [-Wunused-variable]
fsl_esdhc_spl.c:34:8: warning: unused variable 'val' [-Wunused-variable]
fsl_esdhc_spl.c:33:6: warning: unused variable 'blklen' [-Wunused-variable]
fsl_esdhc_spl.c:105:7: warning: 'tmp_buf' may be used uninitialized in this
function [-Wuninitialized]
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
York Sun [Fri, 28 Mar 2014 22:07:27 +0000 (15:07 -0700)]
powerpc/mpc85xx: Add workaround for erratum A007212
Erratum A007212 for DDR is about a runaway condition for DDR PLL
oscilliator. Please refer to erratum document for detail.
For this workaround to work, DDR PLL needs to be disabled in RCW.
However, u-boot needs to know the expected PLL ratio. We put the
ratio in a reserved field RCW[18:23]. U-boot will skip this workaround
if DDR PLL ratio is set, or the reserved field is not set.
Workaround for erratum A007212 applies to selected versions of
B4/T4 SoCs. It is safe to apply the workaround to all versions. It
is helpful for upgrading SoC without changing u-boot. In case DDR
PLL is disabled by RCW (part of the erratum workaround), we need this
u-boot workround to bring up DDR clock.
Put a delay of 5 millisecond after reset so that ULPI phy
gets enough time to come out of reset. Erratum A007075 applies
to following SOCs and their variants, if any
P1010 rev 1.0
B4860 rev 1.0, 2.0
P4080 rev 2.0, 3.0
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
In the current Datasheet for VSC8514 there is a mistake, saying that
the PHY id is 0x70570. The real value in the identifier registers is
0x70670. Linux PHY driver uses 0x70670 also.
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@freescale.com> Cc: York Sun <yorksun@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
York Sun [Wed, 19 Mar 2014 20:52:34 +0000 (13:52 -0700)]
driver/fsl_ifc: Add a function to finalize CS0 address binding
For fsl-lsch3 NOR flash boot, IFC CS0 needs to be binded with address
within 32-bit at fist. After u-boot relocates to DDR, CS0 can be binded
to higher address to support large space.
Signed-off-by: York Sun <yorksun@freescale.com> CC: Prabhakar Kushwaha <prabhakar@freescale.com>
Zhao Qiang [Fri, 21 Mar 2014 08:21:45 +0000 (16:21 +0800)]
QE/U-QE: Add U-QE support
Modify code to adapt to both u-qe and qe.
U_QE is a kind of cutted QE.
the differences between U_QE and QE
1. UCC: U_QE supports 2 UCCs while QE supports up to 8 UCCs.
2. IMMR: have different immr base addr.
3. iopin: U_QE doesn't need to config iopin.
Signed-off-by: Zhao Qiang <B45475@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
Zhao Qiang [Fri, 21 Mar 2014 08:21:44 +0000 (16:21 +0800)]
QE/FMAN: modify CONFIG_SYS_QE_FMAN_FW_ADDR to CONFIG_SYS_FMAN_FW_ADDR and CONFIG_SYS_QE_FW_ADDR
CONFIG_SYS_QE_FMAN_FW_ADDR is used to both Fman and QE for microcode address.
Now using CONFIG_SYS_FMAN_FW_ADDR for Fman microcode address,
and CONFIG_SYS_QE_FW_ADDR for QE microcode address.
Signed-off-by: Zhao Qiang <B45475@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
Aneesh Bansal [Tue, 18 Mar 2014 18:11:14 +0000 (23:41 +0530)]
powerpc/mpc85xx: SECURE BOOT- Add secure boot target for T1040QDS and T1040RDB
Secure Boot Target is added for T1040QDS and T1040RDB
Changes:
For Secure boot, CPC is configured as SRAM and used as house
keeping area which needs to be disabled.
So CONFIG_SYS_CPC_REINIT_F is defined for CONFIG_T1040QDS and
CONFIG_T1040RDB
Signed-off-by: Gaurav Rana <gaurav.rana@freescale.com> Signed-off-by: Aneesh Bansal <aneesh.bansal@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
Aneesh Bansal [Tue, 18 Mar 2014 18:10:59 +0000 (23:40 +0530)]
powerpc/mpc85xx: SECURE BOOT- Add secure boot target for T2080QDS
Secure Boot Target is added for T2080QDS
Changes:
For Secure boot, CPC is configured as SRAM and used as house
keeping area which needs to be disabled.
So CONFIG_SYS_CPC_REINIT_F is defined for CONFIG_T2080QDS.
Signed-off-by: Aneesh Bansal <aneesh.bansal@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
Aneesh Bansal [Tue, 18 Mar 2014 18:10:42 +0000 (23:40 +0530)]
powerpc/mpc85xx: SECURE BOOT- Add secure boot target for T4240QDS and T4160QDS
Secure Boot Target is added for T4240QDS and T4160QDS
Changes:
For Secure boot, CPC is configured as SRAM and used as house
keeping area which needs to be disabled.
So CONFIG_SYS_CPC_REINIT_F is defined for CONFIG_T4240QDS.
Signed-off-by: Aneesh Bansal <aneesh.bansal@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
Aneesh Bansal [Tue, 18 Mar 2014 18:10:26 +0000 (23:40 +0530)]
powerpc/mpc85xx: SECURE BOOT- Add secure boot target for B4860QDS
Changes:
1. L2 cache is being invalidated by Boot ROM code for e6500 core.
So removing the invalidation from start.S
2. Clear the LAW and corresponding configuration for CPC. Boot ROM
code uses it as hosekeeping area.
3. For Secure boot, CPC is configured as SRAM and used as house
keeping area. This configuration is to be disabled once in uboot.
Earlier this disabling of CPC as SRAM was happening in cpu_init_r.
As a result cache invalidation function was getting skipped in
case CPC is configured as SRAM.This was causing random crashes.
Signed-off-by: Ruchika Gupta <ruchika.gupta@freescale.com> Signed-off-by: Aneesh Bansal <aneesh.bansal@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
Aneesh Bansal [Wed, 12 Mar 2014 16:30:18 +0000 (22:00 +0530)]
powerpc/mpc85xx: SECURE BOOT- Add NAND secure boot target for BSC9132QDS
In case of secure boot from NAND, the DDR is initialized by the
BootROM using the config words (CF_WORDS) in the CF_HEADER
and u-boot image is copied from NAND to DDR by the BootROM.
So, CONFIG_SYS_RAMBOOT has been defined for Secure Boot from NAND
Signed-off-by: Aneesh Bansal <aneesh.bansal@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
Aneesh Bansal [Fri, 7 Mar 2014 13:42:09 +0000 (19:12 +0530)]
powerpc/p1010rdb: SECURE BOOT enabled for NAND
In case of secure boot from NAND, the DDR is initialized by the
BootROM using the config words (CF_WORDS) in the CF_HEADER
and u-boot image is copied from NAND to DDR by the BootROM.
So, CONFIG_SYS_RAMBOOT has been defined for Secure Boot from NAND.
Signed-off-by: Aneesh Bansal <aneesh.bansal@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
Nikhil Badola [Thu, 19 Dec 2013 05:38:46 +0000 (11:08 +0530)]
fsl/usb: Fix phy type for Second USB controller
Set correct phy_type value for second USB controller.
This is required for supporting SOCs having 2 USB controllers
working simultaneously, one with UTMI phy and other with ULPI phy
Signed-off-by: Nikhil Badola <B46172@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
Alexander Graf [Fri, 11 Apr 2014 15:09:45 +0000 (17:09 +0200)]
PPC 85xx: Add qemu-ppce500 machine
For KVM we have a special PV machine type called "ppce500". This machine
is inspired by the MPC8544DS board, but implements a lot less features
than that one.
It also provides more PCI slots and is supposed to be enumerated by
device tree only.
This patch adds support for the generic ppce500 machine and tries to
rely solely on device tree for device enumeration.
Signed-off-by: Alexander Graf <agraf@suse.de> Acked-by: Scott Wood <scottwood@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
Alexander Graf [Fri, 11 Apr 2014 15:09:43 +0000 (17:09 +0200)]
PPC: 85xx: Generalize DDR TLB mapping function
The DDR mapping function really is just a generic virtual -> physical
mapping function. Generalize it so it can support any virtual starting
offset and IO maps just the same.
Signed-off-by: Alexander Graf <agraf@suse.de> Acked-by: Scott Wood <scottwood@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
Alexander Graf [Fri, 11 Apr 2014 15:09:42 +0000 (17:09 +0200)]
PPC: 85xx: Remove IVOR reset
There is no need to set IVORs to anything but their default values,
so let's leave them where they are.
Suggested-by: Scott Wood <scottwood@freescale.com> Signed-off-by: Alexander Graf <agraf@suse.de> Acked-by: Scott Wood <scottwood@freescale.com>
[York Sun: Add back $(obj)start.S section in mpc8572ds/Makefile] Reviewed-by: York Sun <yorksun@freescale.com>
Alexander Graf [Fri, 11 Apr 2014 15:09:41 +0000 (17:09 +0200)]
fdt_support: Add helper function to read "ranges" property
This patch adds a helper function that can be used to interpret most
"ranges" properties in the device tree.
It reads the n'th range out of a "ranges" array and returns the node's
virtual address of the range, the physical address that range starts at
and the size of the range.
Signed-off-by: Alexander Graf <agraf@suse.de> Acked-by: Scott Wood <scottwood@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
Alexander Graf [Fri, 11 Apr 2014 15:09:40 +0000 (17:09 +0200)]
fdt_support: split fdt_getprop_u32_default
We already have a nice helper to give us a property cell value with default
fall back from a path. Split that into two helpers - one for the old path
based lookup and one to give us a value based on a node offset.
Signed-off-by: Alexander Graf <agraf@suse.de> Acked-by: Scott Wood <scottwood@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
Paul Burton [Mon, 7 Apr 2014 09:11:22 +0000 (10:11 +0100)]
MIPS: allow use of generic board
This patch allows MIPS boards to make use of generic board, replacing
arch/mips/lib/board.c with common/board_{f,r}.c and struct bd_info with
the asm-generic version.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
projects / u-boot.git / log