Andrius Štikonas [Fri, 24 Apr 2020 21:03:29 +0000 (22:03 +0100)]
rockpro64: Enable HDMI output on rockpro64 board
Reference to commit that adds HDMI to other rk3399 boards:
commit 9778edae5576 ("rockchip: Enable HDMI output on rk3399 board w/ HDMI")
Signed-off-by: Andrius Štikonas <andrius@stikonas.eu> Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Cc: Jagan Teki <jagan@amarulasolutions.com> Cc: Kever Yang <kever.yang@rock-chips.com> Tested-by: Mark Kettenis <kettenis@openbsd.org> Reviewed-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Deepak Das [Wed, 15 Apr 2020 03:25:24 +0000 (08:55 +0530)]
rockchip: rk3399: enable spl-fifo-mode for sdmmc
adapting commit fa2047c47310 ("rockchip: rk3328: enable spl-fifo-mode
for emmc and sdmmc") for rk3399.
Since mmc to sram can't do dma, add patch to prevent aborts transferring
TF-A parts.
Signed-off-by: Deepak Das <deepakdas.linux@gmail.com>
- Add DM_ETH support for lx2160aqds, ls2080aqds, ls1088aqds
- QSI related fixes on ls1012a, ls2080a, ls1046a, ls1088a, ls1043a based
platforms
- Bug-fixes/updtaes related to ls1046afrwy, fsl-mc, msi-map property
Marek Vasut [Sat, 11 Apr 2020 18:54:02 +0000 (20:54 +0200)]
ARM: rmobile: Enable support for OpTee on Gen3
Enable OpTee support on R-Car Gen3, so that U-Boot would copy the
OpTee /firmware and /reserved-memory nodes into the Linux DT.
Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org> Cc: Simon Glass <sjg@chromium.org> Cc: Tom Rini <trini@konsulko.com>
Marek Vasut [Sat, 11 Apr 2020 18:50:24 +0000 (20:50 +0200)]
ARM: rmobile: Merge prior-stage firmware DT fragment into U-Boot DT on Gen3
The prior-stage firmware generates DT fragment containing the /firmware
node, /reserved-memory node and /memory@ nodes. Merge these nodes into
the U-Boot DT, so U-Boot can use this information.
Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org> Cc: Simon Glass <sjg@chromium.org> Cc: Tom Rini <trini@konsulko.com>
Marek Vasut [Sat, 11 Apr 2020 18:49:49 +0000 (20:49 +0200)]
ARM: dts: rmobile: Reserve space in R-Car Gen3 DTs
Reserve 4 kiB of space in R-Car Gen3 DTs when those DTs are compiled
to permit patching in OpTee-OS /firmware node, /reserved-memory node
and possibly also additional /memory@ nodes.
Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org> Cc: Simon Glass <sjg@chromium.org> Cc: Tom Rini <trini@konsulko.com>
Marek Vasut [Sat, 11 Apr 2020 19:18:59 +0000 (21:18 +0200)]
fdtdec: Add weak function to patch U-Boot DT right after fdtdec_setup()
Add weak function which is called right after fdtdec_setup() configured
the U-Boot DT. This permits board-specific adjustments to the U-Boot DT
before U-Boot starts parsing the DT. This could be used e.g. to patch in
various custom nodes or merge in DT fragments from prior-stage firmware.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org> Cc: Simon Glass <sjg@chromium.org> Cc: Tom Rini <trini@konsulko.com>
Marek Vasut [Sat, 11 Apr 2020 18:43:07 +0000 (20:43 +0200)]
libfdt: Export overlay_apply_node() as fdt_overlay_apply_node()
This function is useful to merge a subset of DT into another DT, for
example if some prior-stage firmware passes a DT fragment to U-Boot
and U-Boot needs to merge it into its own DT. Export this function
to permit implementing such functionality.
Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org> Cc: Simon Glass <sjg@chromium.org> Cc: Tom Rini <trini@konsulko.com>
This driver is safe to use in SPL without relocation. Denying
DM_FLAG_PRE_RELOC prevents its usability for verifying the main U-Boot
or other artifacts from the SPL unless needless enabling the full driver
set (SPL_OF_PLATDATA).
Fixes: 17e117408571 ("drivers: crypto: rsa_mod_exp: avoid DM_FLAG_PRE_RELOC") CC: Heinrich Schuchardt <xypron.glpk@gmx.de> CC: Marek Vasut <marex@denx.de> Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Simon Glass [Sun, 10 May 2020 18:52:45 +0000 (12:52 -0600)]
test: Use ut_asserteq_mem() where possible
Quite a few tests still use ut_assertok(memcmp(...)) and variants. Modify
them to use the macro designed for this purpose.
Suggested-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com> Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
This macro is only used (tested for existence) in mpc83xx.c, which
unconditionally includes mpc83xx.h where it is unconditionally
defined. Removing it makes the remaining code easier to read.
Ioana Ciornei [Mon, 18 May 2020 11:48:36 +0000 (14:48 +0300)]
arm: dts: ls2080aqds: add CONFIG_MULTI_DTB_FIT support
Add support for selecting the appropriate DTS file depending on the
SERDES protocol used.
The fsl-ls2080a-qds DTS will be used by default if there isn't a DTS
file specifically made for the current SERDES protocol.
This patch adds the necessary DPMAC nodes (DPMAC 1-8) for
protocol 42 (0x2A) on SD#1.
Also, in case CONFIG_DM_ETH and CONFIG_MULTI_DTB_FIT are enabled
implement the board_fit_config_name_match() function in order to choose
the appropriate DTS.
Ioana Ciornei [Mon, 18 May 2020 11:48:35 +0000 (14:48 +0300)]
board: ls2080aqds: transition to DM_ETH
In case CONFIG_DM_ETH is enabled, no hardcoding is necessary for DPAA2
Ethernet devices. Compile out any unnecessary setup when CONFIG_DM_ETH
is activated. Also, force the PCI devices to be enumerated at probe
time.
Ioana Ciornei [Fri, 15 May 2020 06:56:49 +0000 (09:56 +0300)]
board: ls1088aqds: transition to DM_ETH
In case CONFIG_DM_ETH is enabled, no hardcoding is necessary for DPAA2
Ethernet devices. Compile out any unnecessary setup when CONFIG_DM_ETH
is activated. Also, force the PCI devices to be enumerated at probe
time.
Ioana Ciornei [Fri, 15 May 2020 06:56:48 +0000 (09:56 +0300)]
arm: dts: ls1088aqds: add CONFIG_MULTI_DTB_FIT support
Add support for selecting the appropriate DTS file depending on the
SERDES protocol used. The fsl-ls2088a-qds DTS will be used by default if
there isn't a DTS file specifically made for the current SERDES
protocol.
This patch adds support for the on-board ports (DPMAC 1,2 and 4,5) found
on the SERDES protocols 21(0x15) and 29(0x1d) for SD#1.
On the LS1088AQDS board EMDIO1 is used with two onboard RGMII PHYs
(Realtek RTL8211FD-CG), as well as 2 input/output connectors for
mezzanine cards. Configuration signals from the Qixis FPGA control the
routing of the external MDIOs.
Register 0x54 of the Qixis FPGA controls the routing of the EMDIO1 one
of the 2 IO slots. As a consequence, a new node is added to
describe register 0x54 as a MDIO mux controlled with child nodes
describing all the IO slots as MDIO buses.
Also, in case CONFIG_DM_ETH and CONFIG_MULTI_DTB_FIT are enabled
implement the board_fit_config_name_match() function in order to choose
the appropriate DTS.
net: fsl-mc: fixup DPC: add /board/ports node if missing
The DPC fixup for MAC address and enet_if is not made if
/board/ports node is missing in DPC file.
Add /board/ports or /ports nodes if them are missing.
CONFIG_MTD_NOR_FLASH flag needs to be enable for all
boot sources,as all flash drivers need to compile in
TFA Boot.Probe ifc nor flash only when there is nor
flash available on board.So needs to detect ifc-nor
flash at run-time for probing.
In case CONFIG_DM_ETH and CONFIG_MULTI_DTB_FIT are enabled implement the
board_fit_config_name_match() function in order to choose the
appropriate DTS for the current SERDES protocol configuration.
In case CONFIG_DM_ETH is enabled, no hardcoding is necessary for DPAA2
Ethernet devices. Compile out any unnecessary setup when CONFIG_DM_ETH
is activated. Also, force the PCI devices to be enumerated at probe
time.
arm: dts: lx2160aqds: add nodes describing possible mezzanine cards
Add device trees describing possible uses of mezzanine cards depending
on the SERDES protocol employed.
This patch adds DPAA2 networking support for the following protocols on
each SERDES block:
* SD #1: 3, 7, 19, 20
* SD #2: 11
Each SERDES block has a different device tree file per protocol
supported, where the IO SLOTs used are enabled and PHYs located on the
mezzanine cards are described. Also, dpmac nodes are edited and their
associated phy-connection-type and phy-handle are added.
Top DTS files are also added for each combination of protocol on the 3
SERDES blocks.
The LX2160A processor has two external MDIO interfaces, described in the
DTS as emdio1 and emdio2.
On the LX2160AQDS board EMDIO1 is used with two onboard RGMII PHYs
(Realtek RTL8211FD-CG), as well as eight input/output connectors for
mezzanine cards. Configuration signals from the Qixis FPGA control the
routing of the external MDIOs.
Register 0x54 of the Qixis FPGA controls the routing of the EMDIO1 one
of the 8 IO slots. As a consequence, a new node is added to
describe register 0x54 as a MDIO mux controlled with child nodes
describing all the IO slots as MDIO buses.
Also, DPMAC 17 and 18 are updated to reference the on-board PHYs.
Laurentiu Tudor [Mon, 4 May 2020 11:47:11 +0000 (14:47 +0300)]
drivers: net: fsl-mc: fixup msi-map property
Similarly to iommu-map, the msi-map property must also be fixed up
in the device tree, in order for the icid -> streamid translation
be possible in the MSI case as well.
Kuldeep Singh [Mon, 4 May 2020 06:04:55 +0000 (11:34 +0530)]
configs: ls1012a: Unset ENV_ADDR value
LS1012A-FRWY and LS1012A-RDB crashes in flash environment when
CONFIG_ENV_ADDR value is set. Unset the config value in *_tfa_defconfig*
to resolve booting crash.
Kuldeep Singh [Sat, 14 Dec 2019 14:02:56 +0000 (19:32 +0530)]
configs: nxp: Enable CONFIG_SYS_RELOC_GD_ENV_ADDR
Commit 323d3af59fe4 ("configs: ls1012ardb: Enable
CONFIG_SYS_RELOC_GD_ENV_ADDR") enables the config only for LS1012ARDB.
Apart from LS1012A-RDB, other platforms such as LS1012A-FRWY, LS2088A
and LS1046A-RDB/FRWY also require this config to be enabled. This also
helps in resolving booting crash observed in flash environment.
configs: ls1012a: Reduce CONFIG_ENV_SIZE to 0x2000
All LS1012A board variants have same CONFIG_ENV_SECT_SIZE and
CONFIG_ENV_SIZE values. If both config values are same, flash
environment cannot be saved. Since, CONFIG_ENV_SECT_SIZE needs to be
same as that of flash sector size, this entry cannot be changed.
Reduce CONFIG_ENV_SIZE value to 0x2000. This also helps in making config
value aligned with other boards environemt size.
CONFIG_SYS_MALLOC_LEN is currently set to low value and leaves very less
space to do malloc in flash environmet. Increase the value to get more
memory and also make it align with other boards(ls1046a, ls1043a etc.)
config values.
Kuldeep Singh [Fri, 7 Feb 2020 16:45:18 +0000 (22:15 +0530)]
configs: ls2080ardb: Make BOOT command access flash memory as per spi-mem
BOOT command currently access spi-nor flash memory directly. As per spi-mem
framework, flash memory access via absolute addresses is no more possible.
Use flash APIs to access memory instead of directly using it.
Kuldeep Singh [Fri, 7 Feb 2020 16:39:09 +0000 (22:09 +0530)]
configs: ls2080ardb: Make MC_INIT access flash memory as per spi-mem
MC_INIT command currently access spi-nor flash memory directly. As per
spi-mem framework, flash memory access via absolute addresses is no more
possible. Use flash APIs to access memory instead of directly using it.
Kuldeep Singh [Tue, 12 May 2020 09:09:46 +0000 (14:39 +0530)]
configs: ls1046a: Define ENV_ADDR value
CONFIG_ENV_ADDR helps in picking environment from flash before DDR init.
The macro value is already defined in ls1046ardb_tfa_defconfig, also
define the value as 0x40300000 in qspi_defconfig.
ls1046aqds has one spansion flash "S25FL128S_64K" of size 16M with
sector size 64K. Correct ENV_ADDR and ENV_SECT_SIZE value for QSPI and
TFA defconfigs of the board.
Kuldeep Singh [Tue, 11 Feb 2020 09:26:42 +0000 (14:56 +0530)]
configs: ls2080a: Correct ENV_ADDR value
CONFIG_ENV_ADDR helps in picking environment from flash before DDR init.
QSPI region in LS2088ARDB and LS2088AQDS starts from 0x20000000 offset.
Correct the config value i.e 0x80500000 -> 0x20500000.
Also, define config value as 0x20300000 in qspi defconfig.
Kuldeep Singh [Tue, 11 Feb 2020 09:21:35 +0000 (14:51 +0530)]
configs: ls1088a: Correct ENV_ADDR value
CONFIG_ENV_ADDR helps in picking environment from flash before DDR init.
QSPI region starts from 0x20000000 offset.
Correct the config value i.e 0x80500000 -> 0x20500000.
Kuldeep Singh [Thu, 12 Dec 2019 06:19:24 +0000 (11:49 +0530)]
treewide: Update fsl qspi node dt properties as per spi-mem driver
According to new qspi driver, some properties like "bus-num, num-cs,
big-endian" are no longer used. Device endiannes can be determined from
device-type data in driver.
Now use board specific compatibles, generic node names and specific
labels to align with linux device-tree properties.
Also consolidate spi-max-frequency to 50Mhz treewide.
Kuldeep Singh [Tue, 12 May 2020 07:24:07 +0000 (12:54 +0530)]
treewide: Remove unused FSL QSPI config options for Layerscape platforms
Some of these options are not used by the driver anymore and some of
them are obsolete as the information is gathered from the dt. Also
consolidating defines in common headers.
Simon Glass [Sun, 10 May 2020 17:40:03 +0000 (11:40 -0600)]
command: Remove the cmd_tbl_t typedef
We should not use typedefs in U-Boot. They cannot be used as forward
declarations which means that header files must include the full header to
access them.
Drop the typedef and rename the struct to remove the _s suffix which is
now not useful.
Simon Glass [Sun, 10 May 2020 17:39:55 +0000 (11:39 -0600)]
arm: Don't include common.h in header files
It is bad practice to include common.h in other header files since it can
bring in any number of superfluous definitions. It implies that some C
files don't include it and thus may be missing CONFIG options that are set
up by that file. The C files should include these themselves.
Update some header files in arch/arm to drop this.
Tom Rini [Mon, 18 May 2020 12:17:29 +0000 (08:17 -0400)]
Merge tag 'efi-2020-07-rc3' of https://gitlab.denx.de/u-boot/custodians/u-boot-efi
Pull request for UEFI sub-system for efi-2020-07-rc3
A series of patches introduces the possibility to manage UEFI variables
via an OP-TEE module. CONFIG_EFI_MM_COMM_TEE enables this. If this
option is not specified the U-Boot behavior remains unchanged. A defconfig
is provided for compile testing (lx2160ardb_tfa_stmm_defconfig).
An incorrect UEFI memory allocation for fsl-layerscape is fixed
Ilias Apalodimas [Sun, 17 May 2020 19:25:48 +0000 (22:25 +0300)]
configs: lx2160a: Add default config for lx2160a using StMM in OP-TEE
Previous patches allow UEFI secure variables to be stored in an RPMB
device using OPTEE. Add a config for the lx2160a hardware so the feature
gets at least compiled.
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Remove superfluous differences to lx2160ardb_tfa_defconfig. Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
If OP-TEE is compiled with an EDK2 application running in secure world
it can process and store UEFI variables in an RPMB.
Add documentation for the config options enabling this.
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org> Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Ilias Apalodimas [Sun, 17 May 2020 19:25:45 +0000 (22:25 +0300)]
cmd: efidebug: Add support for querying UEFI variable storage
With the previous patches that use OP-TEE and StandAloneMM for UEFI
variable storage we've added functionality for efi_query_variable_info.
So let's add the relevant command to efidebug and retrieve information
about the container used to store UEFI variables
Ilias Apalodimas [Sun, 17 May 2020 19:25:44 +0000 (22:25 +0300)]
efi_loader: Implement EFI variable handling via OP-TEE
In OP-TEE we can run EDK2's StandAloneMM on a secure partition.
StandAloneMM is responsible for the UEFI variable support. In
combination with OP-TEE and it's U-Boot supplicant, variables are
authenticated/validated in secure world and stored on an RPMB partition.
So let's add a new config option in U-Boot implementing the necessary
calls to OP-TEE for the variable management.
Sughosh Ganu [Sun, 17 May 2020 19:25:43 +0000 (22:25 +0300)]
efi_loader: Add headers for EDK2 StandAloneMM communication
In Arm devices OP-TEE has the ability to run StandAloneMM (from EDK2)
in a separate partition and handle UEFI variables.
A following patch introduces this functionality.
Add the headers needed for OP-TEE <--> StandAloneMM communication
Michael Walle [Sun, 17 May 2020 10:29:19 +0000 (12:29 +0200)]
efi_loader: round the memory area in efi_add_memory_map()
Virtually all callers of this function do the rounding on their own.
Some do it right, some don't. Instead of doing this in each caller,
do the rounding in efi_add_memory_map(). Change the size parameter
to bytes instead of pages and remove aligning and size calculation in
all callers.
There is no more need to make the original efi_add_memory_map() (which
takes pages as size) available outside the module. Thus rename it to
efi_add_memory_map_pg() and make it static to prevent further misuse
outside the module.
Signed-off-by: Michael Walle <michael@walle.cc>
Add missing comma in sunxi_display.c. Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Ovidiu Panait [Wed, 6 May 2020 17:38:47 +0000 (20:38 +0300)]
qemu-x86*_defconfig: Enable CONFIG_PCI_INIT_R
Enable CONFIG_PCI_INIT_R for qemux86 and qemux86-64 pci enumeration during
boot in order to eliminate the custom preboot commands in
include/configs/qemu-x86.h.
With CONFIG_DM_PCI enabled, PCI buses are not enumerated at boot, as they
are without that config option enabled. However, there are cases such as DM
PCI-based Ethernet devices that need the PCI bus enumerated so that they
can be discovered by their drivers.
Currently, to solve this, some boards enumerate the pci bus using
"pci enum" preboot command, while others do it manually in board files
(in board_init/board_late_init/etc. functions).
In order to possibly make the pci enumeration process uniform across all
boards, introduce CONFIG_PCI_INIT_R Kconfig option.
This change also preserves the current behavior in the !DM_PCI case
(pci_init is run unconditionally at boot).
Tom Rini [Fri, 15 May 2020 20:42:06 +0000 (16:42 -0400)]
Merge branch '2020-05-15-misc-bugfixes'
- A number of symbol name consistency updates
- JFFS2 bugfix
- Use /* fallthrough */ for now to help at least gcc know when we're
intentionally not 'break;'ing in a switch statement, we'll adopt
fallthrough; later on.
- Assorted other fixes
Jan Luebbe [Wed, 13 May 2020 10:26:24 +0000 (12:26 +0200)]
lib: rsa: avoid overriding the object name when already specified
If "object=" is specified in "keydir" when using the pkcs11 engine do
not append another "object=<key-name-hint>". This makes it possible to
use object names other than the key name hint. These two string
identifiers are not necessarily equal.
Signed-off-by: Jan Luebbe <jlu@pengutronix.de> Signed-off-by: Bastian Krause <bst@pengutronix.de> Reviewed-by: George McCollister <george.mccollister@gmail.com>
Samuel Holland [Thu, 7 May 2020 23:08:10 +0000 (18:08 -0500)]
spl: Always define preloader_console_init
A large number of boards call preloader_console_init unconditionally.
Currently, they fail to build with CONFIG_SPL_SERIAL=n, because the
function is undefined in that case. To fix the build, always define
preloader_console_init, but make it no-op when CONFIG_SPL_SERIAL=n.
For the few boards that did check for CONFIG_SPL_SERIAL before calling
preloader_console_init, remove the checks, since the function can now
be called unconditionally.
Signed-off-by: Samuel Holland <samuel@sholland.org> Reviewed-by: Stefan Roese <sr@denx.de> Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
projects / u-boot.git / log