Marek Vasut [Tue, 21 Jan 2020 19:03:11 +0000 (20:03 +0100)]
mtd: rawnand: denali: Do not reset the block before booting the kernel
The Denali NAND driver in mainline Linux currently cannot deassert the
reset. The upcoming Linux 5.6 will support the reset controlling, and
also set up SPARE_AREA_SKIP_BYTES correctly. So, the Denali driver in
the future kernel will work without relying on any bootloader or firmware.
However, we still need to take care of stable kernel versions for a while.
U-boot should not assert the reset of this controller.
Masahiro Yamada [Tue, 21 Jan 2020 19:03:10 +0000 (20:03 +0100)]
mtd: rawnand: denali_dt: make the core clock optional
The "nand_x" and "ecc" clocks are currently optional. Make the core
clock optional in the same way. This will allow platforms with no clock
driver support to use this driver.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Tested-by: Marek Vasut <marex@denx.de> # On SoCFPGA Arria V
Marek Vasut [Tue, 21 Jan 2020 19:03:09 +0000 (20:03 +0100)]
mtd: rawnand: denali-spl: Add missing hardware init on SoCFPGA
On Altera SoCFPGA, upon either cold-boot or power-on reset, the
Denali NAND IP is initialized by the BootROM ; upon warm-reset,
the Denali NAND IP is NOT initialized by BootROM. In fact, upon
warm-reset, the SoCFPGA BootROM checks whether the SPL image in
on-chip RAM is valid and if so, completely skips re-loading the
SPL from the boot media.
This does sometimes lead to problems where the software left
the boot media in inconsistent state before warm-reset, and
because the BootROM does not reset the boot media, the boot
media is left in this inconsistent state, often until another
component attempts to access the boot media and fails with an
difficult to debug failure. To mitigate this problem, the SPL
on Altera SoCFPGA always resets all the IPs on the SoC early
on boot.
This results in a couple of register values, pre-programmed by
the BootROM, to be lost during this reset. To restore correct
operation of the IP on SoCFPGA, these values must be programmed
back into the controller by the driver. Note that on other SoCs
which do not use the HW-controlled bootstrap, more registers
may have to be programmed.
This also aligns the SPL behavior with the full Denali NAND
driver, which sets these values in denali_hw_init().
Signed-off-by: Marek Vasut <marex@denx.de> Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Martin Fuzzey [Tue, 14 Jan 2020 15:56:18 +0000 (15:56 +0000)]
pmic: allow dump command for non contiguous register maps
Some PMICs (such as the DA9063) have non-contiguous register maps.
Attempting to read the non implemented registers returns an error
rather than a dummy value which causes 'pmic dump' to terminate
prematurely.
Fix this by allowing the PMIC driver to return -ENODATA for such
registers, which will then be displayed as '--' by pmic dump.
Use a single error code rather than any error code so that
we can distinguish between a hardware failure reading the PMIC
and a non implemented register known to the driver.
Signed-off-by: Martin Fuzzey <martin.fuzzey@flowbird.group>
Martin Fuzzey [Tue, 14 Jan 2020 15:56:17 +0000 (15:56 +0000)]
power: regulator: add driver for Dialog DA9063 PMIC
Add a driver for the regulators in the the DA9063 PMIC.
Robert Beckett: move regulator modes to header so board code can set
modes. Correct mode mask used in ldo_set_mode.
Add an option CONFIG_SPL_DM_REGULATOR_DA9063.
Signed-off-by: Martin Fuzzey <martin.fuzzey@flowbird.group> Signed-off-by: Robert Beckett <bob.beckett@collabora.com>
Martin Fuzzey [Tue, 14 Jan 2020 15:56:16 +0000 (15:56 +0000)]
power: pmic: add driver for Dialog DA9063 PMIC
This adds the basic register access operations and child regulator
binding (if a regulator driver exists).
Robert Beckett: simplify accesses by using bottom bit of address as
offset overflow. This avoids the need to track which page we are on.
Add an option CONFIG_SPL_DM_PMIC_DA9063.
Signed-off-by: Martin Fuzzey <martin.fuzzey@flowbird.group> Signed-off-by: Robert Beckett <bob.beckett@collabora.com>
Ian Ray [Tue, 14 Jan 2020 16:18:20 +0000 (16:18 +0000)]
rtc: s35392a: encode command correctly
The 3-bit "command", or register, is encoded within the device address.
Configure the device accordingly, and pass command in DM I2C read/write
calls correctly.
Signed-off-by: Ian Ray <ian.ray@ge.com> Signed-off-by: Robert Beckett <bob.beckett@collabora.com>
This can be used for device tree size reduction similar as
CONFIG_OF_SPL_REMOVE_PROPS option. Some boards must pass the
built-in DTB unchanged to the kernel, thus we may not cut it
down unconditionally. Therefore enable the property removal
list option only if CONFIG_OF_DTB_PROPS_REMOVE is selected.
spi: cadence-qspi: Add support for Cadence Octal SPI controller
Cadence OSPI is similar to QSPI IP except that it supports Octal IO
(8 IO lines) flashes. Add support for Cadence OSPI IP with existing
driver using new compatible
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com> Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Add support for Direct Access Controller mode of Cadence QSPI. This
allows MMIO access to SPI NOR flash providing better read performance.
Direct mode is only exercised if AHB window size is greater than 8MB.
Support for flash address remapping is also not supported at the moment
and can be added in future.
For better performance, driver uses DMA to copy data from flash in
direct mode using dma_memcpy().
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com> Tested-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com> Acked-by: Jagan Teki <jagan@amarulasolutions.com>
Current Cadence QSPI driver has few limitations. It assumes all read
operations to be in Quad mode and thus does not support SFDP parsing.
Also, adding support for new mode such as Octal mode would not be
possible with current configuration. Therefore move the driver over to spi-mem
framework. This has added advantage that driver can be used to support
SPI NAND memories too.
Hence, move driver over to new spi-mem APIs.
Please note that this gets rid of mode bit setting done when
CONFIG_SPL_SPI_XIP is defined as there does not seem to be any user to
that config option.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com> Tested-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com> Acked-by: Jagan Teki <jagan@amarulasolutions.com>
Make sure corresponding setup registers are updated depending on CS.
This ensures that driver can support QSPI flashes on ChipSelects other
than on CS0
Reported-by: Andreas Dannenberg <dannenberg@ti.com> Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com> Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Marcin Wojtas [Thu, 21 Nov 2019 04:38:47 +0000 (05:38 +0100)]
spi: prevent overriding established bus settings
The SPI stack relies on a proper bus speed/mode configuration
by calling dm_spi_claim_bus(). However the hitherto code
allowed to accidentally override those settings in
the spi_get_bus_and_cs() routine.
The initially established speed could be discarded by using
the slave platdata, which turned out to be an issue on
the platforms whose slave maximum supported frequency
is not on par with the maximum frequency of the bus controller.
This patch fixes above issue by configuring the bus from
spi_get_bus_and_cs() only in case it was not done before.
Signed-off-by: Marcin Wojtas <mw@semihalf.com> Reviewed-by: Simon Glass <sjg@chromium.org> Acked-by: Jagan Teki <jagan@amarulasolutions.com>
Bin Meng [Mon, 9 Sep 2019 13:00:03 +0000 (06:00 -0700)]
test: dm: spi: Fix sandbox dm_test_spi_find()
Per sandbox_cs_info(), sandbox spi controller only supports chip
select 0. Current test case tries to locate devices on chip select
1, and any call to spi_get_bus_and_cs() or spi_cs_info() with cs
number 1 should not return 0.
This updates the test case to handle it correctly.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Michael Walle [Tue, 17 Dec 2019 23:09:58 +0000 (00:09 +0100)]
spi: nxp_fspi: new driver for the FlexSPI controller
This is a port of the kernel's spi-nxp-fspi driver. It uses the new
spi-mem interface and does not expose the more generic spi-xfer
interface. The source was taken from the v5.3-rc3 tag.
The port was straightforward:
- remove the interrupt handling and the completion by busy polling the
controller
- remove locks
- move the setup of the memory windows into claim_bus()
- move the setup of the speed into set_speed()
- port the device tree bindings from the original fspi_probe() to
ofdata_to_platdata()
There were only some style change fixes, no change in any logic. For
example, there are busy loops where the return code is not handled
correctly, eg. only prints a warning with WARN_ON(). This port
intentionally left most functions unchanged to ease future bugfixes.
This was tested on a custom LS1028A board. Because the LS1028A doesn't
have proper clock framework support, changing the clock speed was not
tested. This also means that it is not possible to change the SPI
speed on LS1028A for now (neither is it possible in the linux driver).
Signed-off-by: Michael Walle <michael@walle.cc> Reviewed-by: Jagan Teki <jagan@amarulasolutions.com> Tested-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Pedro Jardim [Thu, 23 Jan 2020 13:21:05 +0000 (10:21 -0300)]
clock_imx8mq: Remove the function sscg_pll_init()
Function sscg_pll_init() is not used anywhere, so it can simply be deleted.
This was found because of the following sparse
warning:
arch/arm/mach-imx/imx8m/clock_imx8mq.c:702:5: warning: no previous prototype for ‘sscg_pll_init’ [-Wmissing-prototypes]
int sscg_pll_init(u32 pll)
^~~~~~~~~~~~~
Signed-off-by: Pedro Jardim <jardim.c.pedro@gmail.com>
Pedro Jardim [Thu, 23 Jan 2020 13:20:51 +0000 (10:20 -0300)]
clock_imx8mq: Make do_imx8m_showclocks() static
Since do_imx8m_showclocks() is only used inside this file, make it 'static'.
This fixes the following sparse warning:
arch/arm/mach-imx/imx8m/clock_imx8mq.c:836:5: warning: no previous prototype
for ‘do_imx8m_showclocks’ [-Wmissing-prototypes]
int do_imx8m_showclocks(cmd_tbl_t *cmdtp, int flag, int argc,
^~~~~~~~~~~~~~~~~~~
Signed-off-by: Pedro Jardim <jardim.c.pedro@gmail.com>
Joel Johnson [Sun, 26 Jan 2020 16:48:58 +0000 (09:48 -0700)]
arm: mvebu: fix A38x breakage from commit bb872dd930cc
This function parameter usage of load_addr was incorrectly caught in
the clarifying renames of commit bb872dd930cc, which results in boot
failures on Marvell A38x.
Signed-off-by: Joel Johnson <mrjoel@lixil.net> Patch-to: Simon Glass <sjg@chromium.org>
Andre Przywara [Fri, 10 Jan 2020 01:47:32 +0000 (01:47 +0000)]
sunxi: Automate loading from 128KB MMC offset
Since commit 067e0b9684d4 ("sunxi: Allow booting from 128KB SD/eMMC offset")
we support having the SPL loaded from either the traditional 8KB SD
card/eMMC offset, or from the alternative location at 128KB. However the
sector to find the U-Boot image was still hard-coded at compile time,
and had to be adjusted for one of the two choices.
Since we can actually override the function to return the sector offset,
we can just check the boot source byte there to select the proper offset
based on from where the SPL was loaded.
This allows the very same binary image to be loaded from either 128KB or
8KB, with the U-Boot proper image always being located just behind the SPL.
Signed-off-by: Andre Przywara <andre.przywara@arm.com> Acked-by: Jagan Teki <jagan@amarulasolutions.com>
Andre Przywara [Fri, 10 Jan 2020 01:47:31 +0000 (01:47 +0000)]
sunxi: SPL: Factor out sunxi_get_boot_source()
The Boot ROM write some boot source ID (SD card, eMMC, SPI, ...) into
a certain location in SRAM, so the SPL can easily determine where to
load U-Boot proper from.
Factor out reading this value, as it will come in handy again shortly.
Signed-off-by: Andre Przywara <andre.przywara@arm.com> Acked-by: Jagan Teki <jagan@amarulasolutions.com>
Giulio Benetti [Thu, 12 Dec 2019 22:53:19 +0000 (23:53 +0100)]
clk: uclass: clk_get_by_name() must not be available if CONFIG_OF_PLATDATA is enabled
clk_get_by_name() requires clk_get_by_id() that is not available if
CONFIG_OF_PLATDATA is defined, so move clk_get_by_name() into #else
condition of #if CONFIG_IS_ENABLED(OF_PLATDATA).
Fabien Parent [Thu, 17 Oct 2019 19:02:05 +0000 (21:02 +0200)]
clk: mediatek: use unsigned type for returning the clk rate
mtk_clk_find_parent_rate is calling clk_get_rate to know the rate
of a parent clock. clk_get_rate returns a ulong, while
mtk_clk_find_parent_rate returns an int. This implicit cast creates
an issue for clock rates big enough to need the full 32 bits to
store its data. When that happen the clk rate will become incorrect
because of the implicit cast between ulong -> int -> ulong.
This commit change the return type of mtk_clk_find_parent_rate to
ulong.
On m68k, block_cache list is relocated, but next and prev list
pointers are not adjusted to the relocated struct list_head address,
so the first iteration over the block_cache list hangs.
This patch initializes the block_cache list after relocation.
Signed-off-by: Angelo Durgehello <angelo.dureghello@timesys.com> Reviewed-by: Eric Nelson <eric@nelint.com>
Now that arch specific dma mapping APIs take care of cache
flush/invalidate, drop local cache flush operation.
While at that fix dma_unmap_single() call to match new prototype
Subsystems such as USB expect dma_map_single() and dma_unmap_single() to
do dcache flush/invalidate operations as required. For example, see
see drivers/usb/gadget/udc/udc-core.c::usb_gadget_map_request().
Currently drivers do this locally, (see drivers/usb/dwc3/ep0.c,
drivers/mtd/nand/raw/denali.c etc..)
Update arch specific dma_map_single() and dma_unmap_single() APIs to do
cache flush/invalidate operations, so that drivers need not implement
them locally.
mingming lee [Thu, 16 Jan 2020 08:11:42 +0000 (16:11 +0800)]
fastboot: mt85xx: add command to flash/erase emmc hwpart
This patch includes the following:
1. Add fastboot command to erase the whole EMMC_USER
2. Add fastboot command to flash image at EMMC_BOOT1
3. Add fastboot command to erase the whole EMMC_BOOT1
4. Enale CONFIG_FASTBOOT_MMC_BOOT1_SUPPORT for mt8518
Signed-off-by: mingming lee <mingming.lee@mediatek.com>
lib: Kconfig dependencies for pseudo-random library
drivers/rng/sandbox_rng.c requires rand() to be defined but configuration
option CONFIG_CONFIG_LIB_RAND selected in drivers/rng/Kconfig does not
exist.
test/lib/test_aes.c requires rand() to be defined.
Fix the selection criteria for choice "Pseudo-random library support type".
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
CONFIG_SPL_RSA is meant to control if lib/rsa/* is used for SPL. Adjust
lib/Makefile to consider this setting.
This was correctly setup with commit 51c14cd128f4 ("verified-boot: Minimal
support for booting U-Boot proper from SPL") and got lost with commit 089df18bfe9d ("lib: move hash CONFIG options to Kconfig").
Fixes: 089df18bfe9d ("lib: move hash CONFIG options to Kconfig") Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Chen-Yu Tsai [Sun, 12 Jan 2020 15:36:15 +0000 (23:36 +0800)]
sunxi: Add Libre Computer ALL-H5-CC H5 board
The Libre Computer ALL-H5-CC board is an upgraded version of the
ALL-H3-CC. Changes include:
- Gigabit Ethernet via external RTL8211E Ethernet PHY
- 16 MiB SPI NOR flash memory
- PoE tap header
- Line out jack removed
Only H5 variant test samples were made available, and the vendor is not
certain whether other SoC variants would be made or not. Furthermore the
board is a minor upgrade compared to the ALL-H3-CC. Thus the device tree
simply includes the one for the ALL-H3-CC, and adds the changes on top.
The device tree was synced over from the Linux kernel, along with other
H3/H5 changes, in a previous patch. Thus only the defconfig and an entry
to the MAINTAINERS file is added.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
[jagan: drop CONFIG_SYS_SPI_U_BOOT_OFFS] Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Chen-Yu Tsai [Sun, 12 Jan 2020 15:36:14 +0000 (23:36 +0800)]
sunxi: Add Libre Computer ALL-H3-IT H5 board
The Libre Computer ALL-H3-IT board is a small single board computer that
is roughly the same size as the Raspberry Pi Zero, or around 20% smaller
than a credit card.
The board features:
- H2, H3, or H5 SoC from Allwinner
- 2 DDR3 DRAM chips
- Realtek RTL8821CU based WiFi module
- 128 Mbit SPI-NOR flash
- micro-SD card slot
- micro HDMI video output
- FPC connector for camera sensor module
- generic Raspberri-Pi style 40 pin GPIO header
- additional pin headers for extra USB host ports, ananlog audio and
IR receiver
Only H5 variant test samples were made available, but the vendor does
have plans to include at least an H3 variant. Thus the device tree is
split much like the ALL-H3-CC, with a common dtsi file for the board
design, and separate dts files including the common board file and the
SoC dtsi file. The other variants will be added as they are made
available.
The device tree was synced over from the Linux kernel, along with other
H3/H5 changes, in a previous patch. Thus only the defconfig and an entry
to the MAINTAINERS file is added.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
[jagan: drop CONFIG_SYS_SPI_U_BOOT_OFFS] Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Andre Przywara [Mon, 6 Jan 2020 01:29:10 +0000 (01:29 +0000)]
sunxi: move CONFIG_SYS_SPI_U_BOOT_OFFS out of defconfig
For Allwinner SoCs the CONFIG_SYS_SPI_U_BOOT_OFFS value is not really a
board choice: The boot ROM only loads the SPL from offset 0 of the SPI
NOR flash, and loads at most 32KB. This is a similar situation as on MMC,
so consequently we create our "joint" image (SPL + U-Boot proper) with
that 32KB offset during the build.
So define the value of this symbol to be 32KB by default for every
Allwinner SoC. This removes the definition of this symbol from the
_defconfig files, and avoids every board to define this over and over
again.
Signed-off-by: Andre Przywara <andre.przywara@arm.com> Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Andre Przywara [Wed, 1 Jan 2020 23:44:49 +0000 (23:44 +0000)]
sunxi: defconfig: R40 boards: enable USB
Now that the USB PHY on the Allwinner R40 SoC is supported, enable USB
support for the two R40 boards U-Boot supports.
For this we need to add the GPIO pin that powers the USB port(s), also
enable the usual suspects (OHCI/EHCI support).
Signed-off-by: Andre Przywara <andre.przywara@arm.com> Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Andre Przywara [Wed, 1 Jan 2020 23:44:48 +0000 (23:44 +0000)]
phy: sun4i-usb: Add Allwinner R40 support
Since every Allwinner USB PHY seems to be slightly different from each
other, we need to add the compatible string and the respective data
structure to make it work on the R40/V40 SoC.
Nothing spectacular this time, just one less USB controller than the H3.
Copied from the Linux kernel.
Signed-off-by: Andre Przywara <andre.przywara@arm.com> Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
- cleanup of pinmux node names
- addition of Security ID, MBUS, CSI, crypto engine, video codec,
pmu, and thermal sensor device nodes for both SoCs
- addition of deinterlacing engine device node on H3
- cleanup of RTC device node and addition of its clocks
- various board cleanups and improvements
- removal of pinmux node for GPIO lines
- cpufreq / DVFS
- HDMI output
- UART-based Bluetooth
- audio codec
- USB ports
- new boards
Most of the changes don't concern U-boot.
Signed-off-by: Chen-Yu Tsai <wens@csie.org> Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Simon Glass [Sat, 28 Dec 2019 17:45:07 +0000 (10:45 -0700)]
common: Move hang() to the same header as panic()
At present panic() is in the vsprintf.h header file. That does not seem
like an obvious choice for hang(), even though it relates to panic(). So
let's put hang() in its own header.
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Migrate a few more files] Signed-off-by: Tom Rini <trini@konsulko.com>
Simon Glass [Sat, 28 Dec 2019 17:45:04 +0000 (10:45 -0700)]
common: Rename and move source()
This function has a very generic name which does not adequately describe
its purpose. Rename it and move it to image.h, since it relates to reading
a script from an image.
Simon Glass [Sat, 28 Dec 2019 17:44:54 +0000 (10:44 -0700)]
common: Move device-tree setup functions to fdt_support.h
These functions relate to setting up the device tree for booting the OS.
The fdt_support.h header file supports similar functions, so move these
there.
Simon Glass [Sat, 28 Dec 2019 17:44:51 +0000 (10:44 -0700)]
common: Drop CONFIG_HAS_POST
This only exists to control whether the post/ directory is build. It is
just as easy to check this in the Makefile. Remove CONFIG_HAS_POST and use
an ifdef in the Makefile instead.
Simon Glass [Sat, 28 Dec 2019 17:44:50 +0000 (10:44 -0700)]
common: Drop CONFIG_POST_STD/ALT_LIST
These CONFIG options are not used anymore. CONFIG_POST_ALT_LIST just
causes CONFIG_POST_STD_LIST to be set and it causes tests.c to be
compiled. So just make compiling tests.c unconditional.