]> git.dujemihanovic.xyz Git - u-boot.git/log
u-boot.git
3 years agoarm: socfpga: smc: Add function to get usercode
Siew Chin Lim [Thu, 25 Mar 2021 06:07:45 +0000 (14:07 +0800)]
arm: socfpga: smc: Add function to get usercode

Add function to send mailbox command via SMC to get usercode from SDM.

Signed-off-by: Siew Chin Lim <elly.siew.chin.lim@intel.com>
Reviewed-by: Ley Foon Tan <ley.foon.tan@intel.com>
3 years agoarm: socfpga: Enable FIT signature with crc32 for SOC64 devices
Siew Chin Lim [Wed, 24 Mar 2021 15:56:37 +0000 (23:56 +0800)]
arm: socfpga: Enable FIT signature with crc32 for SOC64 devices

Add signature with crc32 value for all images in binman node for FIT
image in device tree. And, enable FIT signature checking for Stratix10
and Agilex ATF and VAB sdmmc boot.

Signed-off-by: Siew Chin Lim <elly.siew.chin.lim@intel.com>
3 years agoarm: socfpga: Changed to store QSPI reference clock in kHz
Siew Chin Lim [Wed, 24 Mar 2021 09:16:50 +0000 (17:16 +0800)]
arm: socfpga: Changed to store QSPI reference clock in kHz

Changed to store QSPI reference clock in kHz instead of Hz in
boot scratch cold0 register for Stratix10 and Agilex.

This patch is in preparation for Intel N5X SDRAM driver
support. Reserved 4 bits for Intel N5X SDRAM driver,
and there will be 28 bits to store QSPI reference clock.
Due to limited bits, QSPI reference clock frequency is
converted to kHz from Hz.

Signed-off-by: Siew Chin Lim <elly.siew.chin.lim@intel.com>
Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
3 years agoarm: socfpga: Move Stratix10 and Agilex clock manager common code
Siew Chin Lim [Wed, 24 Mar 2021 09:16:49 +0000 (17:16 +0800)]
arm: socfpga: Move Stratix10 and Agilex clock manager common code

Move duplicated function cm_get_qspi_controller_clk_hz to clock_manager.c.

Signed-off-by: Siew Chin Lim <elly.siew.chin.lim@intel.com>
Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
Reviewed-by: Ley Foon Tan <ley.foon.tan@intel.com>
3 years agoarm: socfpga: Restructure Stratix10 and Agilex handoff code
Siew Chin Lim [Wed, 24 Mar 2021 05:11:38 +0000 (13:11 +0800)]
arm: socfpga: Restructure Stratix10 and Agilex handoff code

Restructure Stratix10 and Agilex handoff code to used by
all SOC64 devices, in preparation to support handoff for
Diamond Mesa.

Remove wrap_pinmux_config_s10.c. Add wrap_handoff_soc64.c
which contains the generic function to parse the handoff
data.

Update system_manager_soc64.c to use generic handoff
function in wrap_handoff_soc64.c.

Signed-off-by: Siew Chin Lim <elly.siew.chin.lim@intel.com>
Reviewed-by: Ley Foon Tan <ley.foon.tan@intel.com>
3 years agoarm: socfpga: Rearrange sequence of macros in handoff_soc64.h
Siew Chin Lim [Wed, 24 Mar 2021 05:11:37 +0000 (13:11 +0800)]
arm: socfpga: Rearrange sequence of macros in handoff_soc64.h

Rearrange sequence of macros in handoff_soc64.h without any functionality
change. In preparation for Stratix10 and Agilex handoff function
restructuring.

Signed-off-by: Siew Chin Lim <elly.siew.chin.lim@intel.com>
3 years agoarm: socfpga: Changed system_manager_s10.c to system_manager_soc64.c
Siew Chin Lim [Wed, 24 Mar 2021 05:11:36 +0000 (13:11 +0800)]
arm: socfpga: Changed system_manager_s10.c to system_manager_soc64.c

Rename to common file name to used by all SOC64 devices.
No functionality change.

Signed-off-by: Siew Chin Lim <elly.siew.chin.lim@intel.com>
3 years agoarm: socfpga: Changed wrap_pll_config_s10.c to wrap_pll_config_soc64.c
Siew Chin Lim [Wed, 24 Mar 2021 05:11:35 +0000 (13:11 +0800)]
arm: socfpga: Changed wrap_pll_config_s10.c to wrap_pll_config_soc64.c

Rename to common file name to used by all SOC64 devices.

Signed-off-by: Siew Chin Lim <elly.siew.chin.lim@intel.com>
3 years agoarm: socfpga: Rename Stratix10 and Agilex handoff common macros
Siew Chin Lim [Wed, 24 Mar 2021 05:11:34 +0000 (13:11 +0800)]
arm: socfpga: Rename Stratix10 and Agilex handoff common macros

Rename handoff_s10.h to handoff_soc64.h. Changed macros prefix from
S10_HANDOFF to SOC64_HANDOFF.

Signed-off-by: Siew Chin Lim <elly.siew.chin.lim@intel.com>
3 years agoarm: socfpga: Move Stratix10 and Agilex SPL common code
Siew Chin Lim [Mon, 15 Mar 2021 07:59:16 +0000 (15:59 +0800)]
arm: socfpga: Move Stratix10 and Agilex SPL common code

Move Stratix10 and Agilex SPL common code to spl_soc64.c.
We are in preparation for new n5x device support.
No functional change in this patch.

Signed-off-by: Siew Chin Lim <elly.siew.chin.lim@intel.com>
Reviewed-by: Ley Foon Tan <ley.foon.tan@intel.com>
3 years agoarm: socfpga: smc: Remove unused SMC function ID
Siew Chin Lim [Fri, 12 Mar 2021 09:51:10 +0000 (17:51 +0800)]
arm: socfpga: smc: Remove unused SMC function ID

Remove unused SMC function ID 61 and 62.

Signed-off-by: Siew Chin Lim <elly.siew.chin.lim@intel.com>
Reviewed-by: Ley Foon Tan <ley.foon.tan@intel.com>
3 years agoMerge branch '2021-04-07-CI-improvements'
Tom Rini [Wed, 7 Apr 2021 19:54:07 +0000 (15:54 -0400)]
Merge branch '2021-04-07-CI-improvements'

- Assorted Azure/GitLab improvements
- Move the Dockerfile used for making containers in CI in to this
  repository.

3 years agotools: Integrate the Dockerfile used for CI
Tom Rini [Mon, 15 Mar 2021 17:19:01 +0000 (13:19 -0400)]
tools: Integrate the Dockerfile used for CI

Integrate the Dockerfile from
https://source.denx.de/u-boot/gitlab-ci-runner.git as of
commit bc6130d572f1 ("Dockerfile: Remove high UID/GID") and introduce a
short rST on how to build the container.

Cc: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
3 years agoAzure/GitLab: bump OpenSBI version to 0.9
Heinrich Schuchardt [Fri, 2 Apr 2021 09:42:01 +0000 (11:42 +0200)]
Azure/GitLab: bump OpenSBI version to 0.9

Version 0.9 of OpenSBI provides the system reset extension which allows us
to reset and power off boards without board specific code.

Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
3 years agoMerge branch '2021-04-07-fs-updates'
Tom Rini [Wed, 7 Apr 2021 15:14:13 +0000 (11:14 -0400)]
Merge branch '2021-04-07-fs-updates'

- JFFS2 updates

3 years agopytest: Lower pygit2 requirement
Tom Rini [Fri, 26 Feb 2021 12:52:28 +0000 (07:52 -0500)]
pytest: Lower pygit2 requirement

The latest versions of pygit2 are not available in practically any
distribution at this time.  Furthermore, we don't need the latest in
order to run all of our testsuites.  Reduce this version requirement to
something older that meets our needs while still supporting running our
tests on older hosts (and so, test labs).

Reported-by: Tom Warren <twarren@nvidia.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
3 years agoGitLab: Remove "tags" stanzas
Tom Rini [Fri, 26 Feb 2021 12:52:27 +0000 (07:52 -0500)]
GitLab: Remove "tags" stanzas

Given the structure of our current GitLab tests, we don't make real use
of the tags.  Furthermore, these tags prevent the automatic usage of the
default GitLab runners.  Remove these tags.

Reported-by: Roger Meier <r.meier@siemens.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
3 years agoAzure: Rework SH / Renesas job
Tom Rini [Mon, 15 Feb 2021 15:52:19 +0000 (10:52 -0500)]
Azure: Rework SH / Renesas job

Now that there is a single SuperH platform, rework the Azure job
slightly.  Azure build time limits mean that we need to split the world
build up still.  Make a single build job for the single Renesas SuperH
platform as well as all of the ARM platforms from Renesas.

Cc: Marek Vasut <marek.vasut+renesas@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
3 years agoJFFS2: fix jffs2 summary datacrc status uninitialized
Wagner Popov dos Santos [Tue, 23 Feb 2021 03:49:00 +0000 (00:49 -0300)]
JFFS2: fix jffs2 summary datacrc status uninitialized

The function jffs2_1pass_read_inode() was discarding the summary
inodes and dirent because the value in datacrc flag wasn't
initialized in function jffs2_sum_process_sum_data().

This fix initializes the status of all summary records to indicate
that the CRC needs to be verified when they are loaded.

Before this fix, the behaviors produced by the undefined value of
datacrc was:
- Summary's registries were discarded when 'b->datacrc' is equal
  as 'CRC_BAD'.
- Summary's registries were not checked when b->datacrc differs of
  'CRC_BAD' and 'CRC_UNKNOWN'

So, almost all of the time the crc just isn't checked, and in some
cases the registries are discarded.

Signed-off-by: Wagner Popov dos Santos <wpopov@gmail.com>
3 years agoJFFS2: fix the reading address over nand's limit
Wagner Popov dos Santos [Tue, 23 Feb 2021 02:30:58 +0000 (23:30 -0300)]
JFFS2: fix the reading address over nand's limit

Fixes address violation in functions read_nand_cached() and
read_onenand_cached(). This happens because these functions
try to read a fixed amount
of data even when the offset+length
is above the nand's limit.

Signed-off-by: Wagner Popov dos Santos <wpopov@gmail.com>
3 years agoMerge tag 'mmc-2021-4-6' of https://source.denx.de/u-boot/custodians/u-boot-mmc
Tom Rini [Wed, 7 Apr 2021 02:42:55 +0000 (22:42 -0400)]
Merge tag 'mmc-2021-4-6' of https://source.denx.de/u-boot/custodians/u-boot-mmc

Update hwpartition usage
Check bootbus's arguments
workaround for erratum A-011334 for fsl_esdhc driver
add pulse width detection workaround for fsl_esdhc driver
Use alias num before checking mmc index when creating device

3 years agoMerge https://source.denx.de/u-boot/custodians/u-boot-usb
Tom Rini [Tue, 6 Apr 2021 18:11:21 +0000 (14:11 -0400)]
Merge https://source.denx.de/u-boot/custodians/u-boot-usb

- XHCI fixes

3 years agousb: xhci: Make debug output better readable and checkpatch clean
Stefan Roese [Tue, 6 Apr 2021 10:10:18 +0000 (12:10 +0200)]
usb: xhci: Make debug output better readable and checkpatch clean

This change makes debugging a bit easier as the output is better
readable with the added space. The explicit le16_to_cpu() is not
needed in the output. Also this patch moves the strings into one line
to make the patch checkpatch clean.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Aaron Williams <awilliams@marvell.com>
Cc: Chandrakala Chavva <cchavva@marvell.com>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Marek Vasut <marex@denx.de>
3 years agousb: xhci: Add missing xhci_readl()
Aaron Williams [Tue, 6 Apr 2021 10:10:17 +0000 (12:10 +0200)]
usb: xhci: Add missing xhci_readl()

Accessing the xHCI controller registers should be done via the
xhci_readl/writel functions. This patch adds this to a few missing
places.

Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Chandrakala Chavva <cchavva@marvell.com>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Marek Vasut <marex@denx.de>
3 years agousb: hub: Fix usb_get_port_status() for big-endian platforms
Aaron Williams [Tue, 6 Apr 2021 10:10:16 +0000 (12:10 +0200)]
usb: hub: Fix usb_get_port_status() for big-endian platforms

Add missing endianness conversions to usb_get_port_status(). This
(amongst others) is necessary to enable the use of USB 3 hubs on
big-endian platforms like MIPS Octeon.

Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Chandrakala Chavva <cchavva@marvell.com>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Marek Vasut <marex@denx.de>
3 years agoMerge tag 'u-boot-amlogic-20210406' of https://source.denx.de/u-boot/custodians/u...
Tom Rini [Tue, 6 Apr 2021 12:37:28 +0000 (08:37 -0400)]
Merge tag 'u-boot-amlogic-20210406' of https://source.denx.de/u-boot/custodians/u-boot-amlogic

- Add MMIO MDIO mux driver
- Add Amlogic G12A MDIO mux driver
- Add DM_MDIO support for designware ethernet driver
- Add Amlogic Meson8b and later designware ethernet glue driver
- Switch all amlogic boards to Amlogic designware ethernet glue driver
- Switch all amlogic boards to DM_MDIO when necessary
- Remove all static ethernet setup code

3 years agoMerge https://source.denx.de/u-boot/custodians/u-boot-marvell
Tom Rini [Tue, 6 Apr 2021 12:37:06 +0000 (08:37 -0400)]
Merge https://source.denx.de/u-boot/custodians/u-boot-marvell

- Enhance WDT handling (starting / stopping) and introduce
  CONFIG_WATCHDOG_AUTOSTART to allow disabling of autostart of
  the WDT (Pali)

3 years agoMerge https://source.denx.de/u-boot/custodians/u-boot-cfi-flash
Tom Rini [Tue, 6 Apr 2021 12:36:49 +0000 (08:36 -0400)]
Merge https://source.denx.de/u-boot/custodians/u-boot-cfi-flash

- Fix detection of 8-bit bus flash devices via address shift

3 years agoMerge tag 'dm-pull-6apr21' of https://source.denx.de/u-boot/custodians/u-boot-dm
Tom Rini [Tue, 6 Apr 2021 12:36:11 +0000 (08:36 -0400)]
Merge tag 'dm-pull-6apr21' of https://source.denx.de/u-boot/custodians/u-boot-dm

ENOSYS clean-up
Minor dtoc improvements
Convert CONFIG_MISC_INIT_F to Kconfig
Allow unit tests to run on any board
pylibfdt build-rule fix

3 years agommc: mmc-uclass: Use dev_seq() to read aliases node's index
Aswath Govindraju [Thu, 25 Mar 2021 07:18:48 +0000 (12:48 +0530)]
mmc: mmc-uclass: Use dev_seq() to read aliases node's index

Use dev_seq() to read aliases node's index and pass it as device number
for creating bulk device.

Suggested-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
3 years agommc: Check for device with a seq number equal to num before checking against index
Aswath Govindraju [Thu, 25 Mar 2021 07:18:47 +0000 (12:48 +0530)]
mmc: Check for device with a seq number equal to num before checking against index

First check if there is an alias for the device tree node defined with the
given num before checking against device index.

Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
3 years agoboard: sl28: enable HS400 mode again
Michael Walle [Wed, 17 Mar 2021 14:01:38 +0000 (15:01 +0100)]
board: sl28: enable HS400 mode again

Now that it is working reliable on the LS1028A SoC, reenable support for
it.

Signed-off-by: Michael Walle <michael@walle.cc>
3 years agommc: fsl_esdhc: add pulse width detection workaround
Michael Walle [Wed, 17 Mar 2021 14:01:37 +0000 (15:01 +0100)]
mmc: fsl_esdhc: add pulse width detection workaround

HS400 mode on the LS1028A SoC isn't reliable. The linux driver has a
workaroung for the pulse width detection. Apply this workaround in
u-boot, too.

This will make HS400 mode work reliably on the LS1028A SoC.

Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
3 years agommc: fsl_esdhc: add workaround for erratum A-011334
Michael Walle [Wed, 17 Mar 2021 14:01:36 +0000 (15:01 +0100)]
mmc: fsl_esdhc: add workaround for erratum A-011334

LS1028A SoCs are restricted in what divider values are allowed for HS400
mode. This is basically a port from the corresponding linux driver.

Signed-off-by: Michael Walle <michael@walle.cc>
3 years agocmd: mmc: check whether bootbus's arguments is valid or not
Jaehoon Chung [Fri, 26 Feb 2021 09:38:20 +0000 (18:38 +0900)]
cmd: mmc: check whether bootbus's arguments is valid or not

According to Specification, each bit have valid value.
But it doesn't check whether arguments is valid or not.
It has potential bug with arguments passed by wrong value.

Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
3 years agocmd: mmc: modify more readable about hwpartition usage
Jaehoon Chung [Fri, 26 Feb 2021 07:07:18 +0000 (16:07 +0900)]
cmd: mmc: modify more readable about hwpartition usage

Modified more readable about hwpartition usage.
Because it's difficult to understand how to use its command.
The arguments didn't optional.
mmc hwpartition needs to pass <USER> <GP> <MODE> as arguments.
Description about each arguments what is required is the below:
 USER - <user> <enh> <start> <cnt> <wrrel> <{on|off}>
 GP   - <{gp1|gp2|gp3|gp4}> <cnt> <enh> <wrrel> <{on|off}>
 MODE - <{check|set|complete}>

Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
3 years agoarm: meson: remove static ethernet link setup
Neil Armstrong [Thu, 25 Feb 2021 08:44:38 +0000 (09:44 +0100)]
arm: meson: remove static ethernet link setup

The static ethernet link type config code is no more needed because now handled by
the meson8b glue driver, delete it.

Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
3 years agoarm: meson: remove static ethernet memory power domain enable
Neil Armstrong [Thu, 25 Feb 2021 08:44:37 +0000 (09:44 +0100)]
arm: meson: remove static ethernet memory power domain enable

The ethernet memory power domain is handled by the meson-ee-pwrc driver,
delete the static code.

Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
3 years agonet: designware: remove amlogic compatibles
Neil Armstrong [Thu, 25 Feb 2021 08:44:36 +0000 (09:44 +0100)]
net: designware: remove amlogic compatibles

These compatibles are now handled by the dwmac_meson8b glue driver.

Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
3 years agoconfigs: meson: use Designware glue driver for Amlogic Meson8b & later SoCs
Neil Armstrong [Thu, 25 Feb 2021 08:44:35 +0000 (09:44 +0100)]
configs: meson: use Designware glue driver for Amlogic Meson8b & later SoCs

Use the proper Synopsys DWMAC Meson8b glue to handle the ethernet link type.

Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
3 years agoarm: meson: remove static MDIO mux handling
Neil Armstrong [Thu, 25 Feb 2021 08:44:34 +0000 (09:44 +0100)]
arm: meson: remove static MDIO mux handling

The static MDIO mux handling in mach-meson is no more needed, delete it.

Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
3 years agoconfigs: update Amlogic Meson G12A, G12B & SM1 configs for MDIO MUX
Neil Armstrong [Thu, 25 Feb 2021 08:44:33 +0000 (09:44 +0100)]
configs: update Amlogic Meson G12A, G12B & SM1 configs for MDIO MUX

Use DM_MDIO and the new G12A MDIO MUX driver for G12A, G12B & SM1 boards.

Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
3 years agoconfigs: update Amlogic Meson GXL & GXM config for MDIO MUX
Neil Armstrong [Thu, 25 Feb 2021 08:44:32 +0000 (09:44 +0100)]
configs: update Amlogic Meson GXL & GXM config for MDIO MUX

Use DM_MDIO and the new MMIOREG MDIO MUX driver for GXL & GXM board.

Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
3 years agonet: designware: add Amlogic Meson8b & later glue driver
Neil Armstrong [Wed, 24 Feb 2021 19:33:56 +0000 (20:33 +0100)]
net: designware: add Amlogic Meson8b & later glue driver

This adds a proper glue driver for the Designware DWMAC ethernet MAC IP
found in the Amlogic Meson8, GXBB, GXL, GXM, G12A, G12B & SM1 SoCs.

This is aimed to replace the static ethernet link setup found on the board
init code for the Amlogic SoC based boards.

Tested on a libretech-cc (S905x Internal RMII 10/100 PHY) and Khadas VIM3 (A113d
with external 10/100/1000 RGMII PHY) to cover the most extreme setups.

Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
3 years agonet: add Amlogic Meson G12A MDIO MUX driver
Neil Armstrong [Wed, 24 Feb 2021 16:31:53 +0000 (17:31 +0100)]
net: add Amlogic Meson G12A MDIO MUX driver

The Amlogic G12A & compatible SoCs embeds a mux to either communicate with
the external PHY or the internal 10/100 PHY.

This adds support for this mux as a MDIO MUX device.

Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
3 years agonet: designware: add DM_MDIO support
Neil Armstrong [Wed, 24 Feb 2021 14:02:39 +0000 (15:02 +0100)]
net: designware: add DM_MDIO support

Add support for DM_MDIO to connect to PHY and expose a MDIO device for the
internal MDIO bus in order to dynamically connect to MDIO PHYs with DT
with eventual MDIO muxes in between.

Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
3 years agonet: add MMIO Register MDIO MUX driver
Neil Armstrong [Wed, 24 Feb 2021 14:02:23 +0000 (15:02 +0100)]
net: add MMIO Register MDIO MUX driver

Add support for MMIO register MDIO muxes based on the Linux mdio-mux-mmioreg driver.

Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
3 years agoarm: mvebu: Espressobin: Enable watchdog support but do not start it
Pali Rohár [Tue, 9 Mar 2021 13:26:57 +0000 (14:26 +0100)]
arm: mvebu: Espressobin: Enable watchdog support but do not start it

Espressobin had disabled watchdog support (CONFIG_WDT) because older stable
Linux kernel versions (which are used by current stable OpenWRT and Debian
versions) do not have support for Armada 3700 watchdog driver. Therefore
they are not able to periodically kick watchdog so Espressobin enter into
boot loop.

This change enable CONFIG_WDT, CONFIG_WDT_ARMADA_37XX and CONFIG_CMD_WDT
options which add support for U-Boot 'wdt' command. And unset new
CONFIG_WATCHDOG_AUTOSTART option which cause that watchdog is not
automatically started by U-Boot during init phase, like when CONFIG_WDT
option is not set at all.

So with this change, U-Boot on Espressobin would have working 'wdt' command
which can be used from boot scripts (e.g. for enabling watchdog prior new
Linux booting kernel). But default behavior of watchdog status stays
unchanged, U-Boot does not start watchdog on Espressobin during its init
phase.

Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
3 years agowatchdog: Allow to use CONFIG_WDT without starting watchdog
Pali Rohár [Tue, 9 Mar 2021 13:26:56 +0000 (14:26 +0100)]
watchdog: Allow to use CONFIG_WDT without starting watchdog

In some cases it is useful to compile support for U-Boot command 'wdt'
without starting HW watchdog in early U-Boot phase. For example when the
user want to start the watchdog only on demand by some boot script.

This change adds a new compile option WATCHDOG_AUTOSTART to control whether
U-Boot should automatically start the watchdog during init phase or not.

This option is enabled by default as it was the default behavior prior
introducing this new change. When compiling U-Boot users can decide to turn
this option off.

Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
3 years agowatchdog: Show error message when initr_watchdog() cannot start watchdog
Pali Rohár [Tue, 9 Mar 2021 13:26:55 +0000 (14:26 +0100)]
watchdog: Show error message when initr_watchdog() cannot start watchdog

Function wdt_start() may fail. So in initr_watchdog() function check return
value of wdt_start() call and print error message when watchdog starting
failed.

Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
3 years agowatchdog: Set/unset GD_FLG_WDT_READY flag in wdt_start()/wdt_stop()
Pali Rohár [Tue, 9 Mar 2021 13:26:54 +0000 (14:26 +0100)]
watchdog: Set/unset GD_FLG_WDT_READY flag in wdt_start()/wdt_stop()

Watchdog is ready after successful call of ops->start() callback in
wdt_start() function. And is stopped after successful call of ops->stop()
callback in wdt_stop function.

So move setting of GD_FLG_WDT_READY flag from initr_watchdog() function to
wdt_start() and ensure that GD_FLG_WDT_READY flag is unset in wdt_stop()
function.

This change ensures that GD_FLG_WDT_READY flag is set only when watchdog is
running. And ensures that flag is also also when watchdog was started not
only by initr_watchdog() call (e.g. by U-Boot 'wdt' command).

Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
3 years agocfi_flash: Fix detection of 8-bit bus flash devices via address shift
Jagannadha Sutradharudu Teki [Fri, 26 Feb 2021 07:51:49 +0000 (08:51 +0100)]
cfi_flash: Fix detection of 8-bit bus flash devices via address shift

We had a problem detecting 8/16bit flash devices connected only via
8bits to the SoC for quite a while. Commit 239cb9d9
[mtd: cfi_flash: Fix CFI flash driver for 8-bit bus support] finally
fixed this 8-bit bus support. But also broke some other boards using
this cfi driver. So this patch had to be reverted.

I spotted a different, simpler approach for this 8-bit bus support
on the barebox mailing list posted by
Oleksij Rempel <bug-track@fisher-privat.net>:

http://www.spinics.net/lists/u-boot-v2/msg14687.html

Here the commit text:

"
Many cfi chips support 16 and 8 bit modes. Most important
difference is use of so called "Q15/A-1" pin. In 16bit mode this
pin is used for data IO. In 8bit mode, it is an address input
which add one more least significant bit (LSB). In this case
we should shift all adresses by one:
For example 0xaa << 1 = 0x154
"

This patch now is a port of this barebox patch to U-Boot.

Along with the change w.r.t from barebox,
Some flash chips can support multiple bus widths, override the
interface width and limit it to the port width.

Tested on 16-bit Spansion flash on sequoia.
Tested 8-bit flashes like 256M29EW, 512M29EW.

Signed-off-by: Stefan Roese <sr@denx.de>
Tested-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Cc: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Cc: Aaron Williams <awilliams@marvell.com>
Cc: Chandrakala Chavva <cchavva@marvell.com>
Cc: Andre Przywara <andre.przywara@arm.com>
Cc: Vignesh Raghavendra <vigneshr@ti.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Mario Six <mario.six@gdsys.cc>
Cc: York Sun <york.sun@nxp.com>
Cc: Marek Vasut <marek.vasut+renesas@gmail.com>
3 years agotest: Allow tests to run on any board
Simon Glass [Wed, 24 Mar 2021 21:44:33 +0000 (10:44 +1300)]
test: Allow tests to run on any board

Due to a recent change, tests are limited to running on sandbox only.
Correct this so that any architecture can run them.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reported-by: Sean Anderson <seanga2@gmail.com>
Fixes: c79705ea938 ("test: Move dm_test_init() into test-main.c")
Tested-by: Sean Anderson <seanga2@gmail.com>
3 years agosandbox: document parameters of os_realloc()
Heinrich Schuchardt [Sun, 28 Mar 2021 09:05:00 +0000 (11:05 +0200)]
sandbox: document parameters of os_realloc()

Avoid 'make htmldocs' build warnings:

    ./include/os.h:139: warning:
    Function parameter or member 'ptr' not described in 'os_realloc'
    ./include/os.h:139: warning:
    Function parameter or member 'length' not described in 'os_realloc'

Fixes: 14e46dfb176b ("sandbox: Add os_realloc()")
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
3 years agoConvert CONFIG_MISC_INIT_F to Kconfig
Simon Glass [Fri, 26 Mar 2021 03:17:30 +0000 (16:17 +1300)]
Convert CONFIG_MISC_INIT_F to Kconfig

This converts the following to Kconfig:
   CONFIG_MISC_INIT_F

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
3 years agomoveconfig: Handle binary files cleanly
Simon Glass [Fri, 26 Mar 2021 03:17:29 +0000 (16:17 +1300)]
moveconfig: Handle binary files cleanly

Some files are not actually source code and thus can produce unicode
errors. Report this and continue.

Signed-off-by: Simon Glass <sjg@chromium.org>
3 years agolog: Fix up debug_cond() when LOG is enabled
Simon Glass [Fri, 26 Mar 2021 03:17:28 +0000 (16:17 +1300)]
log: Fix up debug_cond() when LOG is enabled

At present debug() statements can cause debuf output to appear when LOG is
enabled but DEBUG is not. This is not intended and it seems that the
condition is wrong.

Fix it.

Signed-off-by: Simon Glass <sjg@chromium.org>
3 years agodtoc: Improve handling of reg properties
Simon Glass [Fri, 26 Mar 2021 03:17:27 +0000 (16:17 +1300)]
dtoc: Improve handling of reg properties

This existing code assumes that a reg property is larger than one cell,
but this is not always the case. Fix this assumption.

Also if a node's parent is missing the #address-cells and #size-cells
properties we use 2 as a default for each. But this should not happen in
practice. More likely the properties were removed for SPL due to there
being no 'u-boot,dm-pre-reloc' property, or similar. Add a warning for
this as the failure can be very confusing.

Signed-off-by: Simon Glass <sjg@chromium.org>
3 years agodtoc: Adjust detection of 64-bit properties
Simon Glass [Fri, 26 Mar 2021 03:17:26 +0000 (16:17 +1300)]
dtoc: Adjust detection of 64-bit properties

At present an empty size is considered to be a 64-bit value. This does not
seem useful and wastes space. Limit the 64-bit detection to where one or
both of the addr/size is two cells or more.

Signed-off-by: Simon Glass <sjg@chromium.org>
3 years agodtoc: Show driver warnings once at the end
Simon Glass [Fri, 26 Mar 2021 03:17:25 +0000 (16:17 +1300)]
dtoc: Show driver warnings once at the end

At present warnings are shown as soon as they are discovered in the
source scannner. But the function that detects them may be called multiple
times.

Collect all the warnings and show them at the end.

Signed-off-by: Simon Glass <sjg@chromium.org>
3 years agobuildman: Add an encoding to the out-env file
Simon Glass [Fri, 26 Mar 2021 01:39:39 +0000 (14:39 +1300)]
buildman: Add an encoding to the out-env file

The environment may contain some unicode characters. At least that is what
seemed to happen on one commit:

Building current source for 1 boards (0 threads, 64 jobs per thread)
    0    0    0 /1       -1      (starting)
Traceback (most recent call last):
  File ".../tools/buildman/buildman", line 64, in <module>
    ret_code = control.DoBuildman(options, args)
  File "tools/buildman/control.py", line 372, in DoBuildman
    options.keep_outputs, options.verbose)
  File ".../tools/buildman/builder.py", line 1704, in BuildBoards
    results = self._single_builder.RunJob(job)
  File ".../tools/buildman/builderthread.py", line 526, in RunJob
    self._WriteResult(result, job.keep_outputs, job.work_in_output)
  File ".../tools//buildman/builderthread.py", line 349, in _WriteResult
    print('%s="%s"' % (var, env[var]), file=fd)
UnicodeEncodeError: 'ascii' codec can't encode characters in position
311-312: ordinal not in range(128)

The problem defies repetition with any change at all to buildman. But
let's set an encoding in any case.

Signed-off-by: Simon Glass <sjg@chromium.org>
3 years agopinctrl: Return -ENOSYS when system call is not available
Simon Glass [Wed, 24 Mar 2021 21:26:11 +0000 (10:26 +1300)]
pinctrl: Return -ENOSYS when system call is not available

Update the code to use -ENOSYS, which is the correct error code for an
unimplemented system call in U-Boot.

Also we should not check for a missing operations array as this is not
permitted. For now this can be covered by an assert().

Signed-off-by: Simon Glass <sjg@chromium.org>
3 years agosimple-pm-bus: Use -ENOSYS for checking missing system call
Simon Glass [Wed, 24 Mar 2021 21:26:10 +0000 (10:26 +1300)]
simple-pm-bus: Use -ENOSYS for checking missing system call

We don't need to check -ENOTSUPP since this is not used for this purpose
in U-Boot. Update the code accordingly.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Sean Anderson <seanga2@gmail.com>
3 years agoclk: Return -ENOSYS when system call is not available
Simon Glass [Wed, 24 Mar 2021 21:26:09 +0000 (10:26 +1300)]
clk: Return -ENOSYS when system call is not available

Update clk_composite_set_parent() to use -ENOSYS, which is the correct
error code for U-Boot. Also rearrange the code so that the error condition
is clearly indicated and the function runs to the end in the normal case,
since this is the common style in U-Boot.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Sean Anderson <seanga2@gmail.com>
3 years agoclk: Update drivers to use -EINVAL
Simon Glass [Wed, 24 Mar 2021 21:26:08 +0000 (10:26 +1300)]
clk: Update drivers to use -EINVAL

At present some drivers use -ENOSUPP to indicate that an unknown or
unsupported clock is used. Most use -EINVAL, indicating an invalid value,
so convert everything to that.

Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
3 years agotlv_eeprom: Return -ENOSYS when system call is not available
Simon Glass [Wed, 24 Mar 2021 21:26:07 +0000 (10:26 +1300)]
tlv_eeprom: Return -ENOSYS when system call is not available

When CMD_TLV_EEPROM is not enabled, use -ENOSYS, which is the correct
error code for U-Boot.

Signed-off-by: Simon Glass <sjg@chromium.org>
3 years agospi: Return -ENOSYS when system call is not available
Simon Glass [Wed, 24 Mar 2021 21:26:06 +0000 (10:26 +1300)]
spi: Return -ENOSYS when system call is not available

Update spi_controller_dma_map_mem_op_data() to use -ENOSYS, which is the
correct error code for U-Boot.

Signed-off-by: Simon Glass <sjg@chromium.org>
3 years agousb: Return -ENOSYS when system call is not available
Simon Glass [Wed, 24 Mar 2021 21:26:05 +0000 (10:26 +1300)]
usb: Return -ENOSYS when system call is not available

Update usb_gadget_release() to use -ENOSYS, which is the correct error
code for U-Boot.

Signed-off-by: Simon Glass <sjg@chromium.org>
3 years agodm: core: Use -ENOSPC in acpi_get_path()
Simon Glass [Wed, 24 Mar 2021 21:26:04 +0000 (10:26 +1300)]
dm: core: Use -ENOSPC in acpi_get_path()

Update this function to use -ENOSPC which is more commly used when a buffer
runs out of space.

Signed-off-by: Simon Glass <sjg@chromium.org>
3 years agodm: core: Document the common error codes
Simon Glass [Wed, 24 Mar 2021 21:26:03 +0000 (10:26 +1300)]
dm: core: Document the common error codes

Driver model uses quite strong conventions on error codes, but these are
currently not clearly documented. Add a description of the commonly used
errors.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Sean Anderson <seanga2@gmail.com>
3 years agopatman: Continue on if warnings are found outside a commit
Simon Glass [Mon, 22 Mar 2021 05:01:42 +0000 (18:01 +1300)]
patman: Continue on if warnings are found outside a commit

While we cannot know which commit the warning relates to, this should not
be fatal. Print the warning and carry on.

Signed-off-by: Simon Glass <sjg@chromium.org>
3 years agodtc: Update the build rule for pylibfdt
Simon Glass [Sat, 27 Mar 2021 22:27:18 +0000 (11:27 +1300)]
dtc: Update the build rule for pylibfdt

Some versions of make complain about using a grouped target without a
recipe:

.../pylibfdt/Makefile:36: *** grouped targets must provide a recipe.  Stop.

Fix this by adding a dummy recipe.

Signed-off-by: Simon Glass <sjg@chromium.org>
3 years agoMerge tag 'rockchip-for-v2021.07' of https://source.denx.de/u-boot/custodians/u-boot...
Tom Rini [Tue, 6 Apr 2021 02:39:10 +0000 (22:39 -0400)]
Merge tag 'rockchip-for-v2021.07' of https://source.denx.de/u-boot/custodians/u-boot-rockchip

- Fix rk3368 lion board support;
- Fix px30 odroid-go2 board support;
- Add rk3399 NanoPi R4s and NanoPi M4B board support;

3 years agoMerge branch 'next'
Tom Rini [Mon, 5 Apr 2021 15:29:57 +0000 (11:29 -0400)]
Merge branch 'next'

3 years agoPrepare v2021.04
Tom Rini [Mon, 5 Apr 2021 15:03:29 +0000 (11:03 -0400)]
Prepare v2021.04

Signed-off-by: Tom Rini <trini@konsulko.com>
3 years agoimx8mn_ddr4_evk: Allow booting the kernel by default
Fabio Estevam [Thu, 4 Mar 2021 11:07:16 +0000 (08:07 -0300)]
imx8mn_ddr4_evk: Allow booting the kernel by default

Currently it is not possible to boot Linux from the SD card
by default.

Make the necessary adjustments to allow it.

Reported-by: Peter Bergin <peter@berginkonsult.se>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Tested-by: Andrey Zhizhikin <andrey.z@gmail.com> # imx8mn_ddr4_evk
Reviewed-by: Peng Fan <peng.fan@nxp.com>
3 years agosphinx: Pin to docutils-0.16
Tom Rini [Sun, 4 Apr 2021 20:04:56 +0000 (16:04 -0400)]
sphinx: Pin to docutils-0.16

In newer docutils writers/latex2e/docutils.sty has a unicode character
in the comments which can in turn cause Python 3.6 at least to fail.
Pin to the previous docutils release for now.

Cc: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
3 years agocmd: CMD_USB depends on USB
Heinrich Schuchardt [Sun, 4 Apr 2021 13:35:07 +0000 (13:35 +0000)]
cmd: CMD_USB depends on USB

The usb command cannot be compiled with CONFIG_USB=n:

ld.bfd: cmd/usb.c:660: undefined reference to `usb_stop'
ld.bfd: cmd/usb.c:663: undefined reference to `usb_started'

Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
3 years agoMakefile: Silence the deprecation script
Simon Glass [Wed, 31 Mar 2021 22:18:13 +0000 (11:18 +1300)]
Makefile: Silence the deprecation script

This bash code is currently showing up in the build unless 'make -s' is
used. We don't normally show these sorts of things as they are confusing.
Also this code was not shown before the recent refactoring of how these
messages are displayed.

Add an '@' to silence it.

Suggested-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Reported-by: Bin Meng <bmeng.cn@gmail.com>
Fixes: 13732528516 ("Makefile: Add common code to report deprecation")
3 years agoMerge tag 'efi-2021-04-rc6' of https://source.denx.de/u-boot/custodians/u-boot-efi
Tom Rini [Wed, 31 Mar 2021 17:05:57 +0000 (13:05 -0400)]
Merge tag 'efi-2021-04-rc6' of https://source.denx.de/u-boot/custodians/u-boot-efi

Pull request for efi-2021-04-rc6

Bug fix:
    Fix ConvertDeviceNodeToText() for Uart()

3 years agoMerge tag 'xilinx-for-v2021.07' of https://source.denx.de/u-boot/custodians/u-boot...
Tom Rini [Wed, 31 Mar 2021 13:47:30 +0000 (09:47 -0400)]
Merge tag 'xilinx-for-v2021.07' of https://source.denx.de/u-boot/custodians/u-boot-microblaze into next

Xilinx changes for v2021.07

net:
- Fix gem PCS support

spi:
- Small trivial fixes

zynq:
- Enable time/timer commands
- Update bitmain platform
- Several DT changes

zynqmp:
- Update clock driver
- mini config alignments
- Add/update psu_init for zcu208/zcu216/zc1275
- Several DT changes
- Enable efi debug command (also for Versal)

3 years agotest: Don't unmount not (yet) mounted system
Andy Shevchenko [Thu, 11 Feb 2021 14:40:12 +0000 (16:40 +0200)]
test: Don't unmount not (yet) mounted system

When test suite tries to create a file for a new filesystem test case and fails,
the clean up of the exception tries to unmount the image, that has not yet been
mounted. When it happens, the fuse_mounted global variable is set to False and
inconveniently the test case tries to use sudo, so without this change the
admin of the machine gets an (annoying) email:

  Subject: *** SECURITY information for example.com ***

  example.com : Feb  5 19:43:47 : ... COMMAND=/bin/umount .../build-sandbox/persistent-data/mnt

and second run of the test cases on uncleaned build folder will ask for sudo
which is not what expected.

Besides that there is a double unmount calls during successfully run test case.

All of these due to over engineered Python try-except clause and people didn't
get it properly at all. The rule of thumb is that don't use more keywords than
try-except in the exception handling code. Nevertheless, here we adjust code
to be less intrusive to the initial logic behind that complex and unclear
constructions in the test case, although it adds a lot of lines of the code,
i.e. splits one exception handler to three, so on each step we know what
cleanup shall perform.

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
3 years agoMerge https://source.denx.de/u-boot/custodians/u-boot-sunxi
Tom Rini [Wed, 31 Mar 2021 11:48:47 +0000 (07:48 -0400)]
Merge https://source.denx.de/u-boot/custodians/u-boot-sunxi

- H616 fixes to keep it in sync with upstream TF-A

3 years agosunxi: dts: H616: Drop reserved-memory node
Andre Przywara [Thu, 25 Mar 2021 16:19:52 +0000 (16:19 +0000)]
sunxi: dts: H616: Drop reserved-memory node

Trusted Firmware now adds the /reserved-memory subnode to the DT at
runtime[1], putting in the right values.

Drop our hard-coded version, as this might clash with the actual values
(which have also changed), and rely on TF-A to add the node.

[1] https://review.trustedfirmware.org/c/TF-A/trusted-firmware-a/+/7770

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
3 years agosunxi: H616: Change TF-A load address to beginning of DRAM
Andre Przywara [Thu, 25 Mar 2021 16:20:13 +0000 (16:20 +0000)]
sunxi: H616: Change TF-A load address to beginning of DRAM

Loading Trusted-Firmware's BL31 at 16KB into DRAM was originally a hack
to allow sharing more code with the other SoCs (which use this offset
in SRAM). However there is no longer a reason for that, as the
problematic macros have been properly separated there.

The latest (and hopefully final) TF-A code drop now changes the load
address to the beginning of DRAM, which is also more easily protected
by the Trustzone memory controller (code to be done).

Adjust the load address of BL31 now, to avoid any issues with
incompatible versions later on (the TF-A patches are about to be merged).

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Samuel Holland <samuel@sholland.org>
3 years agoefi_loader: typo 'devide path'
Heinrich Schuchardt [Wed, 31 Mar 2021 06:34:33 +0000 (06:34 +0000)]
efi_loader: typo 'devide path'

Fix a typo in helloworld.efi.

Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
3 years agoefi_loader: Uart device path missing break
Heinrich Schuchardt [Wed, 31 Mar 2021 06:16:04 +0000 (08:16 +0200)]
efi_loader: Uart device path missing break

In the devicepath node to text conversion for Uart nodes a break statement
is missing.

Indicated by Coverity Scan CID 330038
Fixes: 62df6e9c9994 ("efi_loader: Uart device path")
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
3 years agoMerge tag 'u-boot-atmel-2021.07-a' of https://source.denx.de/u-boot/custodians/u...
Tom Rini [Tue, 30 Mar 2021 15:24:09 +0000 (11:24 -0400)]
Merge tag 'u-boot-atmel-2021.07-a' of https://source.denx.de/u-boot/custodians/u-boot-atmel into next

First set of u-boot-atmel features for 2021.07 cycle:
This small feature set includes the implementation of the slew rate for
the PIO4 pin controller device, and a fix for arm926ejs-based
microprocessors that avoids a crash.

3 years agoxilinx: Enable efi debug command
Michal Simek [Fri, 26 Mar 2021 10:16:24 +0000 (11:16 +0100)]
xilinx: Enable efi debug command

Enable EFI debug command to be able to setup various efi variables to avoid
software like grub.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
3 years agoARM: bitmain: Enable saving variables to SD card
Michal Simek [Mon, 22 Mar 2021 14:43:46 +0000 (15:43 +0100)]
ARM: bitmain: Enable saving variables to SD card

Board has NAND and SD interfaces which can be used for saving variables
too.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
3 years agoARM: bitmain: Enable legacy u-boot format
Michal Simek [Mon, 22 Mar 2021 14:42:02 +0000 (15:42 +0100)]
ARM: bitmain: Enable legacy u-boot format

Still legacy formats are used that's why enable them by default.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
3 years agoARM: bitmain: Enable nand and smcc drivers
Michal Simek [Thu, 18 Mar 2021 15:04:44 +0000 (16:04 +0100)]
ARM: bitmain: Enable nand and smcc drivers

Enable nand and smcc via DT.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
3 years agospi: xilinx_spi: Trivial fixes in axi qspi driver
T Karthik Reddy [Wed, 17 Mar 2021 07:01:50 +0000 (01:01 -0600)]
spi: xilinx_spi: Trivial fixes in axi qspi driver

Use __func__ instead for function name in debug.
Use Linux style u32 instead of uint32_t.

Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Acked-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
3 years agoxilinx: Sync DTs with Linux kernel
Michal Simek [Thu, 26 Nov 2020 13:25:02 +0000 (14:25 +0100)]
xilinx: Sync DTs with Linux kernel

There are several changes which happen in mainline kernel which should get
also to U-Boot. Here is the list of patches from the kernel:

- ARM: zynq: Fix leds subnode name for zc702/zybo-z7
- arm64: dts: zynqmp: Fix leds subnode name for zcu100/ultra96 v1
- arm64: dts: zynqmp: Fix u48 si5382 chip on zcu111
- arm64: dts: zynqmp: Wire up the DisplayPort subsystem
- arm64: dts: zynqmp: Add DisplayPort subsystem
- arm64: dts: zynqmp: Add DPDMA node
- arm64: dts: zynqmp: Enable phy driver for Sata on zcu102/zcu104/zcu106
- arm64: dts: zynqmp: Enable si5341 driver for zcu102/106/111
- arm64: dts: zynqmp: Add DT description for si5328 for zcu102/zcu106
- arm64: dts: zynqmp-zcu100-revC: correct interrupt flags
- arm64: dts: xilinx: align GPIO hog names with dtschema
- arm64: zynqmp: Add Xilinx AES node
- dt: bindings: dma: xilinx: dpdma: DT bindings for Xilinx DPDMA

but also some other changes have been done.
- Using only one compatible string for adxl345 on zturn
- Remove Xilinx internal DP bindings
- Remove USB3.0 serdes configurations
- Remove SATA serdes configuration for zc1232
- Resort nvmem_firmware
- Update nand compatible string
- Aling power-domains property for sd0/1

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
3 years agoclk: zynqmp: Fix clk dump values
T Karthik Reddy [Thu, 25 Feb 2021 06:44:46 +0000 (23:44 -0700)]
clk: zynqmp: Fix clk dump values

With "clk dump" command, few clocks are showing up incorrect values
and some clocks are displayed as "unknown".

Add missing clocks to zynqmp clock driver to display proper
clocks rates.

Implement a simple way to get clock source, instead of calling
functions. Change existing functions to this simple mechanism.

Fix gem clock name "gem_rx" to "gem_tx" which was incorrect.
Change dbf_fpd & dbf_lpd clk names to dbg_fpd & dbg_lpd.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
3 years agoarm64: zynqmp: Rename clocks as per the Arasan NAND driver
Amit Kumar Mahapatra [Tue, 23 Feb 2021 20:47:20 +0000 (13:47 -0700)]
arm64: zynqmp: Rename clocks as per the Arasan NAND driver

In zynqmp.dtsi file renamed "clk_sys" clock to "controller" and
"clk_flash" clock to "bus" as per upstreamed Arasan NAND driver.
This fixes NAND driver probe failure.

Signed-off-by: Amit Kumar Mahapatra <amit.kumar-mahapatra@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
3 years agoarm64: zynqmp: Update device tree properties for nand flash
Amit Kumar Mahapatra [Thu, 18 Feb 2021 07:50:21 +0000 (00:50 -0700)]
arm64: zynqmp: Update device tree properties for nand flash

Update the following device tree properties for nand flash

- Set software ecc mode.
- Set bch as ecc algo.
- Set read block to 0.

Signed-off-by: Amit Kumar Mahapatra <amit.kumar-mahapatra@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
3 years agoarm64: zynqmp: Update psu_init for zcu1275
Michal Simek [Wed, 17 Feb 2021 12:10:05 +0000 (13:10 +0100)]
arm64: zynqmp: Update psu_init for zcu1275

Update clock/pll setup, ddr, MIOs based on 2020.2 hw design.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
3 years agoarm64: zynqmp: Add idt 8a34001 chip to zcu208/zcu216
Michal Simek [Fri, 22 Jan 2021 13:42:29 +0000 (14:42 +0100)]
arm64: zynqmp: Add idt 8a34001 chip to zcu208/zcu216

There is Linux driver for these chips that's why add it to device tree.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
3 years agoarm64: zynqmp: Add missing psu inits for zcu208/216
Michal Simek [Wed, 17 Feb 2021 08:40:38 +0000 (09:40 +0100)]
arm64: zynqmp: Add missing psu inits for zcu208/216

Add missing configurations file for zcu208 and zcu216.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>