cmd: mvebu/bubt: Add support for sha512 checksum validation for Armada 3700
Armada 3700 BootROM supports also images with sha512 checksums and
mox-imager tool [1] generates such bootable images. Without sha512 support
U-Boot bubt command just prints error message:
cmd: mvebu/bubt: Correctly propagate failure during tftp transport
net_loop() returns signed int type and negative value represents error.
tftp_read_file() returns unsigned size_t type and zero value represents
error. Casting signed negative value to unsigned size_t type cause losing
information about error and bubt thinks that no error happened, and
continue erasing SPI-NOR which cause malfunction device.
Fix this issue by correctly propagating failure during tftp transport.
With this change when there is no eth link, bubt does not erase SPI-NOR
anymore.
=> bubt
Burning U-Boot image "flash-image.bin" from "tftp" to "spi"
ethernet@30000 Waiting for PHY auto negotiation to complete......... TIMEOUT !
ethernet@30000: No link.
Error: Failed to read file flash-image.bin from tftp
Signed-off-by: Pali Rohár <pali@kernel.org> Reviewed-by: Stefan Roese <sr@denx.de>
cmd: mvebu/bubt: Verify image type for all 32-bit Aramda SoCs and Armada 3700
Current image type verification code is specific to 32-bit Armada SoCs but
used only for Armada 38x. Implement image type verification for Armada 3700
and enable Armada 38x image verification for all 32-bit Armada SoCs.
Signed-off-by: Pali Rohár <pali@kernel.org> Reviewed-by: Stefan Roese <sr@denx.de>
Current pin control driver applies SDHCI PHY MUX selection
when board DT calls for eMMC function on MPP wires.
However, for CP side eMMC, only the "armada-8k-cpm-pinctrl"
compatibility string is taken into account, which causes
CP-SDHCI on Armada-7K boards to fail.
This patch adds "armada-7k-pinctrl" compatibility string
handling for the CP-SDHCI PHY configuration case.
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com> Reviewed-by: Igal Liberman <igall@marvell.com> Reviewed-by: Stefan Roese <sr@denx.de>
arm64: a37xx: pinctrl: Implement gpio_request_enable for gpio functionality
To automatically enable GPIO functionality of some MPP pin, it is required
to implement .gpio_request_enable and .gpio_disable_free callbacks in
pinctrl driver and set .request and .rfree callbacks in GPIO driver to
pinctrl_gpio_request / pinctrl_gpio_free functions.
Signed-off-by: Pali Rohár <pali@kernel.org> Reviewed-by: Stefan Roese <sr@denx.de>
This new Armada 38x driver is based on Linux kernel driver. It can set any
pin to any valid function specified in DT like Linux kernel, it provides
support for 'pinmux status -a' command and also for pinctrl_gpio_request().
Signed-off-by: Pali Rohár <pali@kernel.org> Reviewed-by: Stefan Roese <sr@denx.de>
pinctrl: Add new function pinctrl_generic_set_state_prefix()
This new function pinctrl_generic_set_state_prefix() behaves like
pinctrl_generic_set_state() but it takes third string argument which is
used as the prefix for each device tree string property.
This is needed for Marvell pinctrl drivers, becase Linux device tree files
have pinmux properties prefixed by "marvell," string.
This change allows to use generic U-Boot pinctrl functions for Armada 38x
pinctrl driver without need to copy+paste of the majority U-Boot pinctrl
code.
Signed-off-by: Pali Rohár <pali@kernel.org> Reviewed-by: Stefan Roese <sr@denx.de>
mmc: fsl_esdhc: Fix 'Internal clock never stabilised.' error
Only newer eSDHC controllers set PRSSTAT_SDSTB flag. So do not wait until
flag PRSSTAT_SDSTB is set on old pre-2.2 controllers. Instead sleep for
fixed amount of time like it was before commit 6f883e501b65 ("mmc:
fsl_esdhc: Add emmc hs200 support").
This change fixes error 'Internal clock never stabilised.' which is printed
on P2020 board at every access to SD card.
Heiko Thiery [Mon, 20 Jun 2022 03:49:49 +0000 (05:49 +0200)]
pmic: pca9450: permit config on all bucks and LDOs
In order to have the possibility to configure the regulators at system
startup through DM support, all LDOs and bucks must be able to be
changeable. Currently there is a limitation to change the values when
the output is enabled. Since the driver is based on the ROHM BD71837 and a
comment that describes a limitation about switching while the output is
enabled can also be found there, the limitation probably comes from this type.
Andre Przywara [Tue, 12 Jul 2022 11:00:23 +0000 (12:00 +0100)]
ARM: relocate: Fix Thumb code by using proper label type
The generic ARM relocate_code function was using its own function entry
point as a relocation base, and it was obtaining that address by using
the "adr" instruction on that entry point label.
However that label is not just an ordinary label, instead we explicitly
mark it as a function start address. Normally that doesn't change much
(other than for debugging), but when assembled in Thumb mode, newer
versions of the GNU assembler prepare everything for this address being
used as the argument to a "bx" call, so make sure bit 0 is set in there
to mark this function as Thumb code. Of course this doesn't end up very
well when we use this address for the ensuing memcpy operation.
To avoid this problem, and to solve it in a robust way, add an extra
label, which is not marked as a function entry, and use that for the adr
instruction. This lets all assemblers generate the right immediate offset
in the "adr" instruction.
This fixes in particular ARMv7-M ports when using GNU binutils v2.37 or
newer (commit d3e52e120b68 seems to trigger the change in behaviour).
Signed-off-by: Andre Przywara <andre.przywara@arm.com> Reported-by: Jesse Taube <mr.bossman075@gmail.com>
Tom Rini [Tue, 26 Jul 2022 12:32:37 +0000 (08:32 -0400)]
Merge tag 'xilinx-for-v2022.10-rc2' of https://source.denx.de/u-boot/custodians/u-boot-microblaze
Xilinx changes for v2022.10-rc2
fpga:
- Convert SYS_FPGA_CHECK_CTRLC and SYS_FPGA_PROG_FEEDBACK to Kconfig
- Add support for secure bitstream loading
spi:
- xilinx_spi: Add support for memopers and supports_op
- zynq_qspi: Add support for supports_op/child_pre_probe
- zynq_qspi: Fix dummy cycle and qspi speed calculations
xilinx:
- Get rid of #stream-id-cells
- Use fixed partitions for SOM
- Add support for UUID reading from FRU
- Use strlcpy instead of strncpy
- Add reset driver support for ZynqMP and Versal
- Enable power domain driver in ZynqMP and Versal
zynqmp:
- Do no place BSS at 0 which have issue with NULL pointer
- Enable SLG gpio driver
- Disable LMB for mini configurations
- Remove duplicate PMIO_NODE_ID_BASE macro
versal:
- Add xlnx-versal-resets.h header
mmc:
- zynq_sdhci: Fix macro for MMC HS
relocate-rela:
- Fix support for BE hosts
- Define all macros for e_machine and reloc types
misc:
- Get rid of guard macros from ARM and RISC-V
lmb:
- Add support for disabling LMB
serial:
- zynq: Fix baudrate calculation
tests:
- Mark bind tests to run only on sandbox
- List also dm uclass and devres
Peng Fan [Tue, 26 Jul 2022 08:41:22 +0000 (16:41 +0800)]
arm: dts: imx8m: shrink ddr firmware size to actual file size
After we switch to use BINMAN_SYMBOLS, there is no need to pad
the file size to 0x8000 and 0x4000. After we use BINMAN_SYMBOLS,
the u-boot-spl-ddr.bin shrink about 36KB with i.MX8MP-EVK.
Tested-by: Tim Harvey <tharvey@gateworks.com> #imx8m[m,n,p]-venice Signed-off-by: Peng Fan <peng.fan@nxp.com> Reviewed-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Ye Li [Tue, 26 Jul 2022 08:41:16 +0000 (16:41 +0800)]
net: eqos: add function to get phy node and address
Since new atheros PHY driver needs to access its PHY node through
phy device, we have to assign the phy node in ethernet controller
driver. Otherwise the PHY driver will fail to get some nodes
and properties.
Signed-off-by: Ye Li <ye.li@nxp.com> Signed-off-by: Peng Fan <peng.fan@nxp.com>
Peng Fan [Tue, 26 Jul 2022 08:41:14 +0000 (16:41 +0800)]
net: dwc_eth_qos: public some functions
Move macros and structures to header file and make some functions
public, so that could used by other files, this is to
prepare split platform specific config to one file.
Ye Li [Tue, 26 Jul 2022 08:41:07 +0000 (16:41 +0800)]
ddr: imx: Add i.MX9 DDR controller driver
Since i.MX9 uses same DDR PHY with i.MX8M, split the DDRPHY to a common
directory under imx, then use dedicated ddr controller driver for each
iMX9 and iMX8M.
The DDRPHY registers are space compressed, so it needs conversion to
access the DDRPHY address. Introduce a common PHY address remap function
for both iMX8M and iMX9 for all PHY registers accessing.
Signed-off-by: Ye Li <ye.li@nxp.com> Signed-off-by: Peng Fan <peng.fan@nxp.com>
Peng Fan [Tue, 26 Jul 2022 08:41:03 +0000 (16:41 +0800)]
imx: imx9: Add M33 release prepare function
To support on-demand booting M33 image from A core. SPL needs
to follow M33 kick up sequence to release M33 firstly,
then set M33 CPUWAIT signal. ATF will clear CPUWAIT to kick
M33 to run.
The prepare function also works around the M33 TCM ECC issue by
clean the TCM. Also enable sentinel handshake and WDOG1 clock
for M33 stop and reset.
Signed-off-by: Ye Li <ye.li@nxp.com> Signed-off-by: Peng Fan <peng.fan@nxp.com>
Alice Guo [Tue, 26 Jul 2022 08:40:59 +0000 (16:40 +0800)]
misc: fuse: support to access fuse on i.MX93
i.MX93 fuse can be accessed through FSB and s400-api. Add mapping tables
for i.MX93. The offset address of FSB accessing OTP shadow registers is
different between i.MX8ULP and i.MX93, so use macro to define the offset
address instead of hardcode.
Signed-off-by: Alice Guo <alice.guo@nxp.com> Signed-off-by: Peng Fan <peng.fan@nxp.com>
Alice Guo [Tue, 26 Jul 2022 08:40:58 +0000 (16:40 +0800)]
misc: imx8ulp: move fuse.c from imx8ulp to sentinel
The i.MX93 platform wants to reuse drivers/misc/imx8ulp/fuse.c. Moving
fuse.c from the folder imx8ulp to sentinel makes it can be used by other
platforms.
Signed-off-by: Alice Guo <alice.guo@nxp.com> Signed-off-by: Peng Fan <peng.fan@nxp.com>
Ye Li [Tue, 26 Jul 2022 08:40:54 +0000 (16:40 +0800)]
imx: imx9: Add TRDC driver for TRDC init
Add TRDC driver to iMX9. The TRDC init splits to two phases:
1. Early init phase will release TRDC from Sentinel and open write
permission to the memory where SPL image runs. Sentinel will set
the memory to RX only after ROM authentication for the OEM
closed part.
2. Init phase will configure TRDC to allow non-secure master to
access DDR. So the peripherals can work in u-boot.
Signed-off-by: Ye Li <ye.li@nxp.com> Signed-off-by: Peng Fan <peng.fan@nxp.com>
Peng Fan [Tue, 26 Jul 2022 08:40:37 +0000 (16:40 +0800)]
imx: move get_boot_device to common file
i.MX8MN/P/ULP supports ROM API, they have almost same get_boot_device
implementation, so move to a common file. And when support i.MX9,
no need to include the other function copy.
Since sys_proto.h is included in imx_romapi.c, there will be build
warning for i.MX8M because wdog_regs not defined, so include imx-regs.h
in i.MX8M sys_proro.h
Ye Li [Tue, 26 Jul 2022 08:40:34 +0000 (16:40 +0800)]
imx: spl: Allow iMX7/8/8M to overwrite spl_board_boot_device
Move the default mapping of spl_boot_device to weak function of
spl_board_boot_device. So that every board of iMX7/8/8M can overwrite
this function to implement specific mapping.
Reviewed-by: Peng Fan <peng.fan@nxp.com> Signed-off-by: Ye Li <ye.li@nxp.com> Signed-off-by: Peng Fan <peng.fan@nxp.com>
MAINTAINERS: Update file list for ARM Freescale IMX
The MAINTAINERS file currently lists files in
arch/arm/include/asm/arch-imx/ being part of the IMX maintainers
purview, however the arch/arm/include/asm/ directory also contains the
directories arch-imx8, arch-imx8m, arch-imx8ulp and arch-imxrt which
would also appear to be relevant to the team. Tweak the entry to cover
these directories so that tools like get_maintainers.pl will suggest
relevant maintainers when making changes just in these directories.
Marek Vasut [Tue, 12 Jul 2022 17:41:29 +0000 (19:41 +0200)]
binman: Increase default fitImage data section resize step from 1k to 64k
Currently the fitImage data area is resized in 1 kiB steps. This works
when bundling smaller images below some 1 MiB, but when bundling large
images into the fitImage, this make binman spend extreme amount of time
and CPU just spinning in pylibfdt FdtSw.check_space() until the size
grows enough for the large image to fit into the data area. Increase
the default step to 64 kiB, which is a reasonable compromise -- the
U-Boot blobs are somewhere in the 64kiB...1MiB range, DT blob are just
short of 64 kiB, and so are the other blobs. This reduces binman runtime
with 32 MiB blob from 2.3 minutes to 5 seconds.
The following can be used to trigger the problem if rand.bin is some 32 MiB.
"
/ {
itb {
fit {
images {
test {
compression = "none";
description = "none";
type = "flat_dt";
Patrick Delaunay [Tue, 12 Jul 2022 07:39:49 +0000 (09:39 +0200)]
log: force DEBUG when LOG_DEBUG is activated
When CONFIG_LOG is activated, if LOG_DEBUG is defined in a file and
DEBUG is not defined the trace with debug() macro are not displayed,
because the parameter cond : _DEBUG = 0 is checked in debug_cond().
With this patch the define DEBUG, used to force the trace generated by
debug() macro, is linked with the define LOG_DEBUG, used to force the
trace generated by other macros (log_debug, dev_dbg, pr_debug).
We only need to define LOG_DEBUG in a file to activate all the
traces generated by any U-Boot debug macro, as it is described in
/doc/develop/logging.rst
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
If parameter drv of lists_bind_fdt() is specified, we want to bind to this
specific driver even if its field of_match is NULL.
If entry->of_match is NULL, we should not dereference it in a debug
statement.
Fixes: d3e773613b6d ("dm: core: Use U-Boot logging instead of pr_debug()") Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com> Reviewed-by: Simon Glass <sjg@chromium.org>
When programming qspi flash speed we need to check the requested flash
speed not to exceed the spi max frequency. In the current implementation
we are checking qspi ref clk instead. This commit fixes the issue by
checking the requested speed and programs the specified max frequency.
projects / u-boot.git / log