Chris Brandt [Wed, 23 Aug 2017 19:53:59 +0000 (14:53 -0500)]
ARM: dts: renesas: Add RZ/A1 GR-Peach board
Add board code and DTs for Renesas RZ/A1 SoC-based GR-Peach,
which is a cheap development platform with RZ/A1H SoC. The
DTs are imported from Linux 5.0.11, commit d5a2675b207d .
Currently supported are UART, ethernet and RPC SPI. The board
can be booted from RPC SPI by writing the u-boot.bin binary
to the beginning of the SPI NOR, e.g. using the "sf" command.
The board can also be booted via JTAG by setting text base to
0x20020000, loading u-boot.bin there via JTAG and executing it
from that address.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Chris Brandt <chris.brandt@renesas.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Ang, Chee Hong [Fri, 3 May 2019 08:18:27 +0000 (01:18 -0700)]
ARM: socfpga: stratix10: Probe FPGA status before bridge enable
Send CONFIG_STATUS and RECONFIG_STATUS mailbox commands to Secure
Device Manager (SDM) to get the status of FPGA and make sure the
FPGA is in user mode before enable the bridge.
Signed-off-by: Ang, Chee Hong <chee.hong.ang@intel.com>
Ang, Chee Hong [Fri, 3 May 2019 08:19:08 +0000 (01:19 -0700)]
ARM: socfpga: stratix10: Disable FPGA2SOC reset
Software must never reset FPGA2SOC bridge. This bridge must only be
reset by POR/COLD/WARM reset. Asserting the FPGA2SOC reset by software
can cause the SoC to lock-up if there are traffics being drived into
FPGA2SOC bridge.
Signed-off-by: Ang, Chee Hong <chee.hong.ang@intel.com>
Marek Behún [Thu, 2 May 2019 13:29:12 +0000 (15:29 +0200)]
cmd: pxe: add board specific PXE default path
The list of PXE default paths contains ARCH and SOC specific paths, but
one PXE server can serve different board with the same ARCH and SOC.
This is the case for Turris Omnia and Turris Mox, where ARCH=arm and
SOC=mvebu.
If CONFIG_SYS_BOARD is defined, also try "default-$ARCH-$SOC-$BOARD"
path.
Adam Ford [Tue, 30 Apr 2019 10:21:42 +0000 (05:21 -0500)]
ARM: da850evm: Enable da850-ohci USB host controller
The DA850 EVM has one USB 1.1 OHCI Host controller. With the
host controller now support DM_USB, this patch enables
the respective functions for the da850evm.
Adam Ford [Tue, 30 Apr 2019 10:21:41 +0000 (05:21 -0500)]
usb: ohci: ohci-da8xx: Enable da850-ohci driver with DM support
This patch reuses some former code for the hawkboard, combines it
with some some similar DM_USB compatible code for the OHCI driver,
and enables the use of the da850's OHCI controller with DM_USB
compatibility.
Marek Behún [Mon, 29 Apr 2019 20:40:44 +0000 (22:40 +0200)]
lib: add Zstandard decompression support
Add the zstd library from Linux kernel (only decompression support).
There are minimal changes to build with U-Boot, otherwise the files are
identical to Linux commit dc35da16 from March 2018, the files had not
been touched since in kernel. Also SPDX lincese tags were added.
Marek Behún [Mon, 29 Apr 2019 20:40:43 +0000 (22:40 +0200)]
lib: Add xxhash support
This adds the xxhash support from Linux. Files are almost identical to
those added to Linux in commit 5d240522 ("lib: Add xxhash module") (they
haven't been touched since in Linux). The only difference is to add some
includes to be compatible with U-Boot. Also SPDX lincese tags were
added.
Remove the RDLVL_MASK, RDLVLGATE_MASK, WRLVL_MASK & enable
PHY_INVERT_CLKOUT to enable Hardware leveling for am437x
as recommended by EMIF Tools app note:
display_options_get_banner_priv() overwrites bytes before the start of the
buffer if the buffer size is less then 3. This case occurs in the Sandbox
when executing the `ut_print` command.
Correctly handle small buffer sizes. Adjust the print unit test to catch
when bytes before the buffer are overwritten.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Reviewed-by: Simon Glass <sjg@chromium.org>
spl: fit: Always enable tracking of os-type if SPL_OS_BOOT is enabled
FIT_IMAGE_TINY is used to reduce the size of the SPL by removing os-type
tracking and recording the loadables into the loaded FDT. When this option
is enabled, it is assumed that the next stage firmware is u-boot.
However this does not play well with the SPL_OS_BOOT option that enables
loading different type of next stage firmware, like the OS itself.
When SPL_OS_BOOT is used, do not disable os-tracking. The added footprint
is about 300 Bytes.
Add a PL310 cache controller driver that is usually found on
ARMv7(32-bit) devices. The driver configures the cache settings that can
be found in the device tree files.
This initial revision only configures basic settings(data & instruction
prefetch, shared-override, data & tag latency). I believe these are the
settings that affect performance the most. Comprehensive settings can be
done by the OS.
Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Linux commit 8ecd7f5970c5 ("ARM: 8483/1: Documentation: l2c: Rename
l2cc to l2c2x0")
Linux docs:
Documentation/devicetree/bindings/arm/l2c2x0.txt
Copied from Linux kernel v5.0.
"The documentation in the l2cc.txt is specific to the L2 cache
controllers L2C210/L2C220/L2C310 (also known as PL210/PL220/PL310
and variants) and not generic as the file name implies. It's not
valid for integrated L2 controllers as found in e.g.
Cortex-A15/A7/A57/A53."
Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
arch: armv8: Provide a way to disable cache maintenance ops
On AM654 SoC(arm64) which is IO coherent and has L3 Cache, cache
maintenance operations being done to support non-coherent platforms
causes issues.
For example, here is how U-Boot prepares/handles a buffer to receive
data from a device (DMA Write). This may vary slightly depending on the
driver framework:
Start DMA to write to destination buffer
Wait for DMA to be done (dma_receive()/dma_memcpy())
Invalidate destination buffer (invalidate_dcache_range())
Read from destination buffer
The invalidate after the DMA is needed in order to read latest data from
memory that’s updated by DMA write. Also, in case random prefetch has
pulled in buffer data during the “wait for DMA” before the DMA has
written to it. This works well for non-coherent architectures.
In case of coherent architecture with L3 cache, DMA write would directly
update L3 cache contents (assuming cacheline is present in L3) without
updating the DDR memory. So invalidate after “wait for DMA” in above
sequence would discard latest data and read will cause stale data to be
fetched from DDR. Therefore invalidate after “wait for DMA” is not
always correct on coherent architecture.
Therefore, provide a Kconfig option to disable cache maintenance ops on
coherent architectures. This has added benefit of improving the
performance of DMA transfers as we no longer need to invalidate/flush
individual cache lines(especially for buffer thats several KBs in size).
In order to facilitate use of same Kconfig across different
architecture, I have added the symbol to top level arch/Kconfig file.
Patch currently disables cache maintenance ops for arm64 only.
flush_dcache_all() and invalidate_dcache_all() are exclusively used
during enabling/disabling dcache and hence are not disabled.
Alex Kiernan [Thu, 18 Apr 2019 20:34:55 +0000 (20:34 +0000)]
Refactor IMAGE_ENABLE_VERIFY to handle builds without SPL verification
If building with SPL_LOAD_FIT_FULL and FIT_SIGNATURE, but without
SPL_FIT_SIGNATURE then the build fails with:
common/built-in.o: In function `fit_image_verify_with_data':
common/image-fit.c:1220: undefined reference to `fit_image_verify_required_sigs'
common/image-fit.c:1244: undefined reference to `fit_image_check_sig'
common/built-in.o: In function `fit_image_load':
common/image-fit.c:1857: undefined reference to `fit_config_verify'
Refactor so that host builds still depend on FIT_SIGNATURE, but target
builds check FIT_SIGNATURE/SPL_FIT_SIGNATURE dependent on the build.
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Tom Rini [Sun, 5 May 2019 00:02:31 +0000 (20:02 -0400)]
Merge tag 'mips-pull-2019-05-03' of git://git.denx.de/u-boot-mips
- mscc: small fixes, enhance network support for Serval, Luton and Ocelot
- mt7620: rename arch to more generic name mtmips
- mips: pass initrd addresses via DT as physical addresses
Marek Vasut [Mon, 18 Mar 2019 03:49:21 +0000 (04:49 +0100)]
cmd: mmc: Make Mode: printout consistent
The "Mode :" line is the only one in "mmc info" output that has a
space in front of the colon. Drop the space to make it consistent
with the rest of the output, e.g.:
=> mmc dev 1 ; mmc info
switch to partitions #0, OK
mmc1 is current device
Device: sd@ee160000
Manufacturer ID: 3
OEM: 5344
Name: SL08G
Bus Speed: 50000000
Mode : SD High Speed (50MHz)
^------------------------------ Remove this space
Rd Block Len: 512
SD version 3.0
High Capacity: Yes
Capacity: 7.4 GiB
Bus Width: 1-bit
Erase Group Size: 512 Bytes
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Jaehoon Chung <jh80.chung@samsung.com> CC: Tom Rini <trini@konsulko.com>
Marek Vasut [Sat, 13 Apr 2019 09:42:34 +0000 (11:42 +0200)]
net: ravb: Avoid unsupported internal delay mode for R-Car E3/D3
According to the R-Car Gen3 Hardware Manual Rev 1.50 of Nov 30, 2018, the
TX clock internal delay mode isn't supported on R-Car E3 (r8a77990) or D3
(r8a77995).
Avoid setting the APSR:TDM bit on these SoCs. Moreover, only set APSR:TDM
when the DT explicitly specifies RGMII ID or TXID mode instead of setting
it unconditionally when the PHY link speed is 1000 Mbit/s.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org> Cc: Joe Hershberger <joe.hershberger@ni.com>
Marek Vasut [Sun, 21 Apr 2019 20:46:25 +0000 (22:46 +0200)]
gpio: renesas: Migrate to pinctrl GPIO accessors
Switch to generic pin controller API for configuring pins as GPIOs
instead of using the ad-hoc call into the R-Car PFC driver. Moreover,
add .free() implementation for the GPIO controller.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Alex Kiernan <alex.kiernan@gmail.com> Cc: Christoph Muellner <christoph.muellner@theobroma-systems.com> Cc: Eugeniu Rosca <roscaeugeniu@gmail.com> Cc: Patrice Chotard <patrice.chotard@st.com> Cc: Patrick DELAUNAY <patrick.delaunay@st.com> Cc: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Cc: Simon Glass <sjg@chromium.org>
Implement the gpio_request_enable/gpio_disable_free callbacks to let
the GPIO driver call the pin control framework and let it reconfigure
pins as GPIOs.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Alex Kiernan <alex.kiernan@gmail.com> Cc: Christoph Muellner <christoph.muellner@theobroma-systems.com> Cc: Eugeniu Rosca <roscaeugeniu@gmail.com> Cc: Patrice Chotard <patrice.chotard@st.com> Cc: Patrick DELAUNAY <patrick.delaunay@st.com> Cc: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Cc: Simon Glass <sjg@chromium.org>
Marek Vasut [Sun, 21 Apr 2019 21:57:23 +0000 (23:57 +0200)]
pinctrl: gpio: Add callback for configuring pin as GPIO
Add callback to configure, and de-configure, pin as a GPIO on the
pin controller side. This matches similar functionality in Linux
and aims to replace the ad-hoc implementations present in U-Boot.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Alex Kiernan <alex.kiernan@gmail.com> Cc: Christoph Muellner <christoph.muellner@theobroma-systems.com> Cc: Eugeniu Rosca <roscaeugeniu@gmail.com> Cc: Patrice Chotard <patrice.chotard@st.com> Cc: Patrick DELAUNAY <patrick.delaunay@st.com> Cc: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Cc: Simon Glass <sjg@chromium.org>
Marek Vasut [Tue, 2 Oct 2018 18:40:58 +0000 (20:40 +0200)]
ARM: renesas: Configure DRAM size from ATF DT fragment
The ATF can pass additional information via the first four registers,
x0...x3. The R-Car Gen3 with mainline ATF, register x1 contains pointer
to a device tree with platform information. Parse this device tree and
extract DRAM size information from it. This is useful on systems where
the DRAM size can vary between configurations.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
of: flip CONFIG_SPL_DISABLE_OF_CONTROL into CONFIG_SPL_OF_CONTROL
As we discussed a couple of times, negative CONFIG options make our
life difficult; CONFIG_SYS_NO_FLASH, CONFIG_SYS_DCACHE_OFF, ...
and here is another one.
Now, there are three boards enabling OF_CONTROL on SPL:
- socfpga_arria5_defconfig
- socfpga_cyclone5_defconfig
- socfpga_socrates_defconfig
This commit adds CONFIG_SPL_OF_CONTROL for them and deletes
CONFIG_SPL_DISABLE_OF_CONTROL from the other boards to invert
the logic.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The support for DaVinci DM* SoCs has been dropped a while ago. There's
still a lot of leftover code in mach-davinci though. Entirely remove
certain files and modify the common code to no longer reference
unsupported chips.
Note: all DaVinci platforms supported in u-boot now define SOC_DA8XX
but not all define SOC_DA850 (e.g. omapl138). We can safely remove
all ifdefs for the former, but let's leave the ones for the latter.
arm: davinci: remove dead code for PHYs used by DaVinci DM* boards
The support for DaVinci DM* boards has been dropped a while ago. The
code for all those PHYs is no longer used and they have their own
proper PHY drivers in drivers/net/phy anyway. Remove all dead code.
Adam Ford [Sun, 28 Apr 2019 21:45:26 +0000 (16:45 -0500)]
ARM: davinci: Remove unused functions from header
There are a few functions defined in the header file, but they are
not referenced by any Davinci code. In order to make a general
function in the future with static function declarations, this
patch will remove the references all together.
Currently mach-mt7620 contains only support for mt7628. To avoid confusion,
rename mach-mt7620 to mach-mtmips, which means MediaTek MIPS platforms.
MT7620 and MT7628 should be distinguished by SOC_MT7620 and SOC_MT7628
because they do not share the same lowlevel codes.
Dependencies of four drivers are changed to SOC_MT7628 as these drivers
are only used by MT7628.
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com> Reviewed-by: Stefan Roese <sr@denx.de> Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Microsemi SoC defines CONFIG_SYS_SDRAM_BASE to be 0x80000000, which
represents the start of kseg0 and represents a virtual address. Meaning
that the initrd_start and initrd_end point somewhere kseg0.
When these parameters are passed to linux kernel through DT
they are pointing somewhere in kseg0 which is a virtual address but linux
kernel expects the addresses to be physical addresses(in kuseg) because
it is converting the physical address to a virtual one.
Therefore update the uboot to pass the physical address of initrd_start
and initrd_end by converting them using the function virt_to_phys before
setting up the DT.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com> Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
In Serval SoC family there are 2 different pcb, both of them have the same
phy, but with different version. Therefore implement board_phy_config
and set all the phys in the same way.
When detecting the board, it was reading a register in the GPIO page of
the phy and based on that value it was making a decision. The bug was that
after the GPIO page for the first phy was set it was not reseted back.
In case the ddr training was failing, it couldn't reset, it was just
hanging. Therefore reimplement it, so when ddr training is failing
it would call _machine_restart, which power downs the DDR and does
a force reset.
Faiz Abbas [Tue, 16 Apr 2019 17:36:58 +0000 (23:06 +0530)]
mmc: sdhci: Add Support for ADMA2
The Standard Host Controller Interface (SDHCI) specification version
3.00 adds support for Advanced DMA (ADMA) for both 64 and 32 bit widths
of DMA. ADMA2 uses a table of descriptors for aggregating DMA requests.
This significantly improves read and write throughput.
Faiz Abbas [Tue, 16 Apr 2019 17:36:57 +0000 (23:06 +0530)]
mmc: sdhci: Move DMA handling to prepare_dma() function
In preparation for addition of ADMA2 support, cleanup SDMA handling by
moving it to a new sdhci_prepare_dma() function. Also add a flags field
in sdhci_host to indicate if DMA is enabled.
Ye Li [Mon, 7 Jan 2019 09:10:27 +0000 (09:10 +0000)]
mmc: fsl_esdhc: Fix wp_enable issue
The wp-gpios property is used for gpio, if this is set, the WP pin is muxed
to gpio function, can't be used as internal WP checking. However the codes
remain to use internal WP checking.
This patch changes to examine the "fsl,wp-controller" for enabling internal WP
checking, and "wp-gpios" for muxing to gpio.
Adam Ford [Tue, 30 Apr 2019 12:53:16 +0000 (07:53 -0500)]
ARM: dts: logicpd-som-lv: Fix MMC1 card detect
The card detect pin was incorrectly using IRQ_TYPE_LEVEL_LOW
instead of GPIO_ACTIVE_LOW when reading the state of the CD pin.
Without this patch, MMC1 won't be detected.
This is the same patch submitted to linux-omap, but I was hoping
to get it applied to U-Boot without having to wait for the
linux adoption and then backporting.
Fixes: 5448ff33f281 ("ARM: DTS: Resync Logic PD SOM-LV 37xx
devkit with Linux 4.18-RC4")
projects / u-boot.git / log