i2c: stm32: fix comment and remove unused AUTOEND bit
Comment within stm32_i2c_message_start is misleading, indicating
that AUTOEND bit is setted while it is actually cleared.
Moreover, the bit is actually never setted so there is no need
to clear it hence get rid of this bit clear and the bit macro
as well.
Activate the support of SCMI regulator to support the scmi_reg11,
scmi_reg18 and scmi_usb33 regulators present in the scmi device tree of
STMicroelectronics boards with stm32mp15-scmi.dtsi
Fixes: 6cccc8d396bf ("ARM: dts: stm32: add SCMI version of STM32 boards (DK1/DK2/ED1/EV1)") Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com> Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Commit 5bb2c550b11e ("arm: mvebu: Move internal registers in
arch_very_early_init() function") moved code from file cpu.c to lowlevel.c,
which moves Marvell internal registers from address INTREG_BASE_ADDR_REG to
SOC_REGS_PHY_BASE.
But the steps describing how to do it correctly were documented only in
older U-Boot versions and commit cefd764222ee ("arm: mvebu: Fix internal
register config on A38x") probably unintentionally removed important
details about MMU from code comments around.
Commit 5bb2c550b11e ("arm: mvebu: Move internal registers in
arch_very_early_init() function") implemented code movement according to
(now incomplete) comments which resulted in semi-broken code.
The result is that I-cache is currently disabled for all Armada 38x boards
and maybe there are some other (unreported / undetected) issues.
Reimplement it correctly. First flush all caches, then disable MMU and L2
cache and then move Marvell internal registers. There is no need to
explicitly disable I-cache.
After this change lzmadec command with lzma image of 0x7000000 bytes is
doing decompression just 5 seconds. Before this change it was 30 seconds.
To make lowlevel.S code more readable, extend asm/pl310.h header file to be
compatible with assembler and use macros from this file.
Fixes: 5bb2c550b11e ("arm: mvebu: Move internal registers in arch_very_early_init() function") Signed-off-by: Pali Rohár <pali@kernel.org> Signed-off-by: Marek Behún <kabel@kernel.org> Reviewed-by: Stefan Roese <sr@denx.de>
For some unknown reason when L2 cache is disabled on Armada 385 then loadb,
loadx and loady commands do not work with higher baudrates than 115200
(they just abort transfer) and lzmadec command with lzma image of size
0x7000000 (maybe even smaller, we tested this one) is doing decompression
for more than 2 minutes. After enabling L2 cache decompression takes only
30s and loadb, loadx and loady are stable and working fine.
git bisect identified problematic commit 3308933d2fe9 ("arm: mvebu: Avoid
reading MVEBU_REG_PCIE_DEVID register too many times"). Before this commit
above issues were not present.
But investigation showed that above issue was possible to reproduce also by
reverting that commit and forcing compiler to do inline optimization of
mvebu_soc_family() function. Which seems that the root of this issue is in
caches and position of instruction of segments. So currently it is unknown
what is or was broken, but code movement, code inlining or other compiler
optimization triggered it.
Commit 3e5ce7ceeb94 ("arm: mvebu: Enable L2 cache on Armada XP") mentioned
that enabling L2 cache on Armada XP improved performance and that Armada
38x has L2 disabled (which is default state) and if needed it has to be
enabled in separate patch. As enabling L2 cache also improve performance
on Armada 38x, enable it.
Note that Aurora cache in no outer mode is available only on Armada XP,
hence it is not touched for Armada 38x code.
Fixes: 3308933d2fe9 ("arm: mvebu: Avoid reading MVEBU_REG_PCIE_DEVID register too many times") Reported-by: Marek Behún <kabel@kernel.org> Signed-off-by: Pali Rohár <pali@kernel.org> Signed-off-by: Marek Behún <kabel@kernel.org> Reviewed-by: Stefan Roese <sr@denx.de>
arm: mvebu: Guard non-AXP code by checking for AXP
Commit c86d53fd88df ("arm: mvebu: Don't disable cache at startup on Armada
XP at all") introduced branch for non-AXP code which was guarded by A38X
condition. Fix this issue by checking for AXP platform, not by A38X.
Fixes: c86d53fd88df ("arm: mvebu: Don't disable cache at startup on Armada XP at all") Signed-off-by: Pali Rohár <pali@kernel.org> Signed-off-by: Marek Behún <kabel@kernel.org> Reviewed-by: Stefan Roese <sr@denx.de>
Commit 3308933d2fe9 ("arm: mvebu: Avoid reading MVEBU_REG_PCIE_DEVID
register too many times") broke support for caches on all Armada SoCs.
Before that commit there was code:
if (mvebu_soc_family() != MVEBU_SOC_A375) {
dcache_enable();
}
And after that commit there is code:
if (IS_ENABLED(CONFIG_ARMADA_375)) {
dcache_enable();
}
Comment above this code says that d-cache should be disabled on Armada 375.
But new code inverted logic and broke Armada 375 and slowed down all other
Armada SoCs (including A38x).
Fix this issue by changing logic to:
if (!IS_ENABLED(CONFIG_ARMADA_375)) {
dcache_enable();
}
Which matches behavior prior that commit.
Fixes: 3308933d2fe9 ("arm: mvebu: Avoid reading MVEBU_REG_PCIE_DEVID register too many times") Signed-off-by: Pali Rohár <pali@kernel.org> Signed-off-by: Marek Behún <kabel@kernel.org> Reviewed-by: Stefan Roese <sr@denx.de>
arm: mvebu: turris_omnia: Allow to use second serial port
Turris Omnia has two serial ports. Both are already specified in device
tree file. But U-Boot by default does not allow to use more than one serial
port unless CONFIG_SERIAL_PROBE_ALL is not enabled.
After enabling CONFIG_SERIAL_PROBE_ALL, U-Boot see also second serial port
(but is inactive by default):
=> coninfo
List of available devices:
serial@12000 00000007 IO stdin stdout stderr
serial@12100 00000007 IO
To allow simultaneously to use more input / output devices it is needed to
enable CONFIG_CONSOLE_MUX option.
With CONFIG_CONSOLE_MUX it is possible to call:
=> setenv stdout 'serial@12000,serial@12100'
And U-Boot output is then visible on both serial ports.
Signed-off-by: Pali Rohár <pali@kernel.org> Reviewed-by: Stefan Roese <sr@denx.de>
tools: termios_linux.h: Fix compilation on non-glibc systems
TCGETS2 is defined in header file asm/ioctls.h provided by linux kernel.
On glib systems it is automatically included by some other glibc include
header file and therefore TCGETS2 is present in termios_linux.h when
linux kernel provides it.
On non-glibc systems (e.g. musl) asm/ioctls.h is not automatically included
which results in the strange error that BOTHER is supported, TCGETS2 not
defined and struct termios does not provide c_ispeed member.
tools/kwboot.c: In function 'kwboot_tty_change_baudrate':
tools/kwboot.c:662:6: error: 'struct termios' has no member named 'c_ospeed'
662 | tio.c_ospeed = tio.c_ispeed = baudrate;
| ^
Fix this issue by explicitly including asm/ioctls.h file which provides
TCGETS2 macro (if supported on selected architecture) to not depending on
glibc auto-include behavior and because termios_linux.h requires it.
With this change it is possible compile kwboot with musl libc.
Reported-by: Michal Vasilek <michal.vasilek@nic.cz> Signed-off-by: Pali Rohár <pali@kernel.org>
Pali Rohár [Mon, 29 Aug 2022 13:44:48 +0000 (15:44 +0200)]
arm: mvebu: turris_mox: Add support for distroboot $fdt_addr
$fdt_addr is mandatory for systems which provides DTB in HW (e.g. ROM) and
wishes to pass that DTB to Linux.
Turris Mox contains DTB binary in SPI NOR memory at "dtb" partition which
starts at offset 0x7f0000 and is 0x10000 bytes long.
Armada 3700 CPU does not allow mapping SPI NOR memory into physical address
space like on other architectures and therefore set $fdt_addr variable to
memory range in RAM and loads this DTB binary from SPI NOR in misc_init_r()
function.
Signed-off-by: Pali Rohár <pali@kernel.org> Reviewed-by: Stefan Roese <sr@denx.de>
Pali Rohár [Sat, 27 Aug 2022 18:49:20 +0000 (20:49 +0200)]
arm: mvebu: turris_{omnia, mox}: Reset bootdelay env for rescue
When rescue mode was activated reset also bootdelay env variable to its
default value. This will ensure that reset button works and starts rescue
mode also in the case when user changed bootdelay env variable to -1 (which
has meaning to not start autoboot).
Signed-off-by: Pali Rohár <pali@kernel.org> Reviewed-by: Marek Behún <kabel@kernel.org> Reviewed-by: Stefan Roese <sr@denx.de>
Pali Rohár [Sat, 27 Aug 2022 18:06:30 +0000 (20:06 +0200)]
board: turris: Initialize serial# env
Store serial number from atsha cryptochip into the serial# env variable.
U-Boot automatically puts content of this variable into the root device
tree property serial-number when booting Linux kernel. Refactor turris
atsha code and from turris_atsha_otp_get_serial_number() function returns
directly string suitable for printing or storing into device tree. Because
during different boot stages is env storage read-only, it is not possible
to always store serial number into env storage. So introduce a new function
turris_atsha_otp_init_serial_number() which is called at later stage and
which ensures that serial number is correctly stored into env.
Signed-off-by: Pali Rohár <pali@kernel.org> Reviewed-by: Marek Behún <kabel@kernel.org> Reviewed-by: Stefan Roese <sr@denx.de>
Pali Rohár [Tue, 23 Aug 2022 12:52:24 +0000 (14:52 +0200)]
cmd: mvebu/bubt: Check for A38x/A37xx OTP secure bits and secure boot
For obvious reasons BootROMS rejects unsigned images when secure boot is
enabled in OTP secure bits. So check for OPT secure bits and do not allow
flashing unsigned images when secure boot is enabled. Access to OTP via
U-Boot fuse API is currently implemented only for A38x and A37xx SoCs.
Additionally Armada 3700 BootROM rejects signed trusted image when secure
boot is not enabled in OTP. So add also check for this case. On the other
hand Armada 38x BootROM acceps images with secure boot header when secure
boot is not enabled in OTP.
OTP secure bits may have burned also boot device source. Check it also and
reject flashing images to target storage which does not match OTP.
Signed-off-by: Pali Rohár <pali@kernel.org> Reviewed-by: Stefan Roese <sr@denx.de>
Stefan Roese [Fri, 19 Aug 2022 07:43:59 +0000 (09:43 +0200)]
tools: kwboot: Change KWBOOT_MSG_RSP_TIMEO_AXP to 10ms
Testing on the theadorable Armada XP platform has shown, thaz using the
current value of 1000ms as response timeout does not result in reliable
booting via kwboot. Using 10ms seems to be much better. So let's change
this value to this 10ms instead.
Signed-off-by: Stefan Roese <sr@denx.de> Acked-by: Pali Rohár <pali@kernel.org>
Tony Dinh [Wed, 17 Aug 2022 21:59:44 +0000 (14:59 -0700)]
arm: kirkwood: Add CONFIG_SUPPORT_PASSING_ATAGS
Add CONFIG_SUPPORT_PASSING_ATAGS and friends to support legacy
image method of booting. Debian and OpenWrt installer use uImage
with appended DTB for these Kirkwood boards.
Signed-off-by: Tony Dinh <mibodhi@gmail.com> Reviewed-by: Stefan Roese <sr@denx.de>
Rasmus Villemoes [Mon, 22 Aug 2022 07:34:23 +0000 (09:34 +0200)]
fdt_support: add optional board_rng_seed() hook
A recurring theme on LKML is the boot process deadlocking due to some
process blocking waiting for random numbers, while the kernel's
Cryptographic Random Number Generator (crng) is not initalized yet,
but that very blocking means no activity happens that would generate
the entropy necessary to finalize seeding the crng.
This is not a problem on boards that have a good hwrng (when the
kernel is configured to trust it), whether in the CPU or in a TPM or
elsewhere. However, that's far from all boards out there. Moreover,
there are consumers in the kernel that try to obtain random numbers
very early, before the kernel has had any chance to initialize any
hwrng or other peripherals.
Allow a board to provide a board_rng_seed() function, which is
responsible for providing a value to be put into the rng-seed property
under the /chosen node.
The board code is responsible for how to actually obtain those
bytes.
- One possibility is for the board to load a seed "file" from
somewhere (it need not be a file in a filesystem of course), and
then ensure that that the same seed file does not get used on
subsequent boots.
* One way to do that is to delete the file, or otherwise mark it as
invalid, then rely on userspace to create a new one, and living
with the possibility of not finding a seed file during some boots.
* Another is to use the scheme used by systemd-boot and create a new
seed file immediately, but in a way that the seed passed to the
kernel and the new (i.e. next) seed cannot be deduced from each
other, see the explanation at
https://lore.kernel.org/lkml/20190929090512.GB13049@gardel-login/
and the current code at
https://github.com/systemd/systemd/blob/main/src/boot/efi/random-seed.c
- The board may have an hwrng from which some bytes can be read; while
the kernel can also do that, doing it in U-Boot and providing a seed
ensures that even very early users in the kernel get good random
numbers.
- If the board has a sensor of some sort (temperature, humidity, GPS,
RTC, whatever), mixing in a reading of that doesn't hurt.
- etc. etc.
These can of course be combined.
The rng-seed property is mixed into the pool used by the linux
kernel's CRNG very early during boot. Whether it then actually
contributes towards the kernel considering the CRNG initialized
depends on whether the kernel has been configured with
CONFIG_RANDOM_TRUST_BOOTLOADER (nowadays overridable via the
random.trust_bootloader command line option). But that's for the BSP
developer to ultimately decide.
So, if the board needs to have all that logic, why not also just have
it do the actual population of /chosen/rng-seed in ft_board_setup(),
which is not that many extra lines of code?
I considered that, but decided handling this logically belongs in
fdt_chosen(). Also, apart from saving the board code from the few
lines of boilerplate, doing it in ft_board_setup() is too late for at
least some use cases. For example, I want to allow the board logic to
decide
ok, let's pass back this buffer and use that as seed, but also let's
set random.trust_bootloader=n so no entropy is credited.
This requires the rng-seed handling to happen before bootargs
handling. For example, during the very first boot, the board might not
have a proper seed file, but the board could still return (a hash of)
some CPU serial# or whatnot, so that at least no two boards ever get
the same seed - the kernel always mixes in the value passed in
rng-seed, but if it is not "trusted", the kernel would still go
through the same motions as it would if no rng-seed was passed before
considering its CRNG initialized. I.e., by returning that
unique-to-this-board value and setting random.trust_bootloader=n, the
board would be no worse off than if board_rng_seed() returned nothing
at all.
UEFI block devices can either mirror U-Boot's internal devices or be
provided by an EFI application like iPXE.
When ConnectController() is invoked for the EFI_BLOCK_IO_PROTOCOL
interface for such an application provided device we create a virtual
U-Boot block device of type "efi_blk".
Currently we do not call ConnectController() when handles for U-Boot's
internal block devices are created. If an EFI application calls
ConnectController() for a handle relating to an internal block device,
we erroneously create an extra "efi_blk" block device.
E.g. the UEFI shell has a command 'connect -r' which calls
ConnectController() for all handles with device path protocol.
In the Supported() method of our EFI_DRIVER_BINDING_PROTOCOL return
EFI_UNSUPPORTED when dealing with an U-Boot internal device.
Change efi_delete_handle() to not free EFI handles twice.
This change tries to resolved an issue seen since U-Boot v2022.07
in which ExitBootService() attempts to release some EFI handles twice.
The issue was seen booting a EFI shell that invokes 'connect -r' and
then boots a Linux kernel. Execution of connect command makes EFI
subsystem to bind a block device for each root block devices EFI handles.
However these EFI device handles are already bound to a driver and we
can have 2 registered devices relating to the same EFI handler. On
ExitBootService(), the loop removing the devices makes these EFI handles
to be released twice which corrupts memory.
This patch prevents the memory release operation caused by the issue but
but does not resolve the underlying problem.
Tom Rini [Thu, 8 Sep 2022 12:33:41 +0000 (08:33 -0400)]
Merge tag 'u-boot-stm32-20220907' of https://source.denx.de/u-boot/custodians/u-boot-stm
- simplify the STM32MP15x package parsing code
- remove test on CONFIG_DM_REGULATOR in stm32mp1 board
and enable CONFIG_DM_REGULATOR for stm32f769-disco
- handle ck_usbo_48m clock provided by USBPHYC to fix the command 'usb start'
after alignment with Linux kernel v5.19 DT (clocks = <&usbphyc>)
- Fix SYS_HZ_CLOCK value for stih410-b2260 board
- Switch STMM32MP15x DHSOM to FMC2 EBI driver
- Remove hwlocks from pinctrl in STM32MP15x to avoid issue with kernel
Sean Anderson [Wed, 7 Sep 2022 05:44:55 +0000 (13:44 +0800)]
net: fm: Add support for FIT firmware
Fman microcode is executable code (AFAICT) loaded into a
coprocessor. As such, if verified boot is enabled, it must be verified
like other executable code. However, this is not currently done.
This commit adds verified boot functionality by encapsulating the
microcode in a FIT, which can then be signed/verified as normal. By
default we allow fallback to unencapsulated firmware, but if
CONFIG_FIT_SIGNATURE is enabled, then we make it mandatory. Because
existing Layerscape do not use this config (instead enabling
CONFIG_CHAIN_OF_TRUST), this should not break any existing boards.
An example (mildly-abbreviated) its is provided below:
Sean Anderson [Tue, 16 Aug 2022 15:16:04 +0000 (11:16 -0400)]
ARMv8/sec_firmware: Convert to use fit_get_data_conf_prop
This reduces sec_firmware_get_data to a single call to
fit_get_data_conf_prop. I think sec_firmware_check_copy_loadable could also
be converted, but it does not map as straightforwardly, so I have left it
for a future cleanup.
Signed-off-by: Sean Anderson <sean.anderson@seco.com> Signed-off-by: Peng Fan <peng.fan@nxp.com>
Sean Anderson [Tue, 16 Aug 2022 15:16:03 +0000 (11:16 -0400)]
image: fit: Add some helpers for getting data
Several different firmware users have repetitive code to extract the
firmware data from a FIT. Add some helper functions to reduce the amount
of repetition. fit_conf_get_prop_node (eventually) calls
fdt_check_node_offset_, so we can avoid an explicit if. In general, this
version avoids printing on error because the callers are typically
library functions, and because the FIT code generally has (debug)
prints of its own. One difference in these helpers is that they use
fit_image_get_data_and_size instead of fit_image_get_data, as the former
handles external data correctly.
Signed-off-by: Sean Anderson <sean.anderson@seco.com> Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Peng Fan <peng.fan@nxp.com>
Pali Rohár [Mon, 1 Aug 2022 12:50:12 +0000 (14:50 +0200)]
board: freescale: p1_p2_rdb_pc: Calculate offsets for eSDHC boot sector
Correctly calculate offsets between SPL and proper U-Boot when new config
option CONFIG_FSL_PREPBL_ESDHC_BOOT_SECTOR for generating eSDHC boot sector
is enabled. Otherwise SPL would not be able to boot proper U-Boot.
Signed-off-by: Pali Rohár <pali@kernel.org> Signed-off-by: Peng Fan <peng.fan@nxp.com>
Pali Rohár [Mon, 1 Aug 2022 13:35:43 +0000 (15:35 +0200)]
board: freescale: p1_p2_rdb_pc: Delete watchdog max6370 node in load_default mode
CPLD in load_default mode ignores watchdog reset signal. It does not reset
board when watchdog triggers reset signal.
Detect load_default mode by GPIO7 - LOAD_DEFAULT_N and delete watchdog
max6370 node from device to prevent registering driver for non-working
watchdog.
Signed-off-by: Pali Rohár <pali@kernel.org> Signed-off-by: Peng Fan <peng.fan@nxp.com>
All *boot env commands overrides default boot source location via i2c.
After board reset without power off, BootROM then starts booting U-Boot
from this specified location instead of the default one.
Add new env command defboot which reverts boot location to the default
value, which in most cases is configurable by HW DIP switches.
And add new env commands norlowerboot, norupperboot, sd2boot to boot from
other locations. norlowerboot would instruct BootROM to boot from lower NOR
bank, norupperboot from upper NOR bank and sd2boot from SD card with
alternative configuration.
Signed-off-by: Pali Rohár <pali@kernel.org> Signed-off-by: Peng Fan <peng.fan@nxp.com>
Removes hwlocks properties from stm32mp151 pinctrl node. These locks
could be used for other purpose, depending on board and software
configuration hence do not enforce their use to protect pinctrl
devices.
This patch is an alignment with Linux device tree with v6.0 as the
hwsem support wasn’t yet added in pincontrol in kernel. It avoids
issues when the Linux kernel is started with the U-Boot device tree.
Cc: Patrice Chotard <patrice.chotard@foss.st.com> Cc: Patrick Delaunay <patrick.delaunay@foss.st.com> Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org> Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Patrice Chotard [Wed, 24 Aug 2022 13:44:40 +0000 (15:44 +0200)]
configs: stm32: Enable CONFIG_DM_REGULATOR for stm32f769-disco
Since commit 5bc6f8c2a97e("video: stm32: remove test on CONFIG_DM_REGULATOR")
backlight was broken with the following message at boot:
stm32-display-dsi dsi@40016c00: Warning: cannot get phy dsi supply
stm32_display display-controller@40016800: panel panel enable backlight error -38
DM_REGULATOR flag must be enabled to fix this issue
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com> Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Patrice Chotard [Wed, 24 Aug 2022 13:42:37 +0000 (15:42 +0200)]
ARM: dts: stm32: Fix display-timings settings for stm32f746-disco
Since commit ef4ce6df3289 "video: stm32: stm32_ltdc: fix data enable polarity"
The panel display output wasn't functional anymore.
Device tree display-timings de-active property value must be updated
to 1.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com> Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Patrick Delaunay [Mon, 20 Jun 2022 10:36:10 +0000 (12:36 +0200)]
board: stm32mp1: remove test on CONFIG_DM_REGULATOR
The tests on CONFIG_DM_REGULATOR, added to avoid compilation issues, can
now be removed, they are no more needed since the commit 16cc5ad0b439
("power: regulator: add dummy helper").
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com> Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Pali Rohár [Mon, 1 Aug 2022 13:31:46 +0000 (15:31 +0200)]
board: freescale: p1_p2_rdb_pc: Turn off watchdog before reset
P1/P2 RDB boards have external max6370 watchdog connected to CPLD and this
watchdog is not deactivated on board reset. So if it is active during board
reset, it can trigger another reset when CPU is booting U-Boot. To prevent
possible infinite reset loop caused by external watchdog, turn it off
before reset.
Do it via a new board_reset_prepare() callback which is called from
do_reset() function before any reset sequence.
Signed-off-by: Pali Rohár <pali@kernel.org> Signed-off-by: Peng Fan <peng.fan@nxp.com>
Pali Rohár [Mon, 1 Aug 2022 13:31:45 +0000 (15:31 +0200)]
board: freescale: p1_p2_rdb_pc: Avoid usage of CPLD's system reset register
CPLD's system reset register is buggy and requires workaround in U-Boot.
So use this kind of board reset only when there is no other reset option.
Introduce a new board_reset_last() callback which is last-stage
board-specific reset and implement CPLD's system reset in this new
board_reset_last() callback instead of board_reset() callback.
Pali Rohár [Mon, 1 Aug 2022 13:31:44 +0000 (15:31 +0200)]
board: freescale: p1_p2_rdb_pc: Add workaround for non-working watchdog
If watchdog timer was already set to non-disabled value then it means that
watchdog timer was already activated, has already expired and caused CPU
reset. If this happened then due to CPLD firmware bug, writing to wd_cfg
register has no effect and therefore it is not possible to reactivate
watchdog timer again. Watchdog starts working again after CPU reset via
non-watchdog method.
Implement this workaround (reset CPU when it was reset by watchdog) to make
watchdog usable again. Watchdog timer logic on these P1/P2 RDB boards is
connected to CPLD, not to SoC itself.
Note that reset does not occur immediately after calling do_reset(), but
after few ms later as real reset is done by CPLD. So it is normal that
function do_reset() returns. Therefore hangs after calling do_reset() to
prevent CPU execution of the rest U-Boot code.
Signed-off-by: Pali Rohár <pali@kernel.org> Signed-off-by: Peng Fan <peng.fan@nxp.com>
Pali Rohár [Mon, 1 Aug 2022 13:31:43 +0000 (15:31 +0200)]
board: freescale: p1_p2_rdb_pc: Add workaround for board reset reboot loop
CPLD's system reset register on P1/P2 RDB boards is not autocleared after
flipping it. If this register is set to one in 100ms after reset starts
then CPLD triggers another CPU reset.
This means that trying to reset board via CPLD system reset register cause
reboot loop. To prevent this reboot loop, the only workaround is to try to
clear CPLD's system reset register as early as possible. U-Boot is already
doing it in its board_early_init_f() function, which seems to be enough as
register is cleared prior CPLD triggers another reset.
But board_early_init_f() is not called from SPL and therefore usage of SPL
can cause reboot loop.
To prevent reboot loop when using SPL, call board_early_init_f() function
in SPL too. For accessing CPLD memory space it is needed to have CPLD entry
in TLB.
With this change it is possible to trigger board reset via CPLD's system
reset register on P2020 RDB board.
Signed-off-by: Pali Rohár <pali@kernel.org> Signed-off-by: Peng Fan <peng.fan@nxp.com>
System reset via the SRST extension in the SBI should be the default.
The driver checks if the extension is available when probing.
So there is no risk in enabling it.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com> Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Sean Anderson [Tue, 30 Aug 2022 21:01:07 +0000 (17:01 -0400)]
ddr: fsl: Make bank_addr_bits reflect actual bits
In both the Freescale DDR controller and the SPD spec, bank address bits
are stored as the number of bank address bits minus 2. For example, if a
chip had 8 banks (3 total bank address bits), the value of
bank_addr_bits would be 1. This is rather surprising for users
configuring their memory manually, since they can't set bank_addr_bits
to the actual number of bank address bits. Rectify this.
There is at least one example of this kind of mistake already, in
board/freescale/t102xrdb/ddr.c. The documented MT40A512M8HX has two bank
address bits, but bank_addr_bits was set to 2, implying 4 bank address
bits. Such a value is reserved in BA_BITS_CS, but I suspect the
controller simply ignores the top bit, making this kind of mistake
harmless, if misleading.
Fixes: e8a7f1c32b5 ("powerpc/t1023rdb: Add T1023 RDB board support") Signed-off-by: Sean Anderson <sean.anderson@seco.com> Signed-off-by: Peng Fan <peng.fan@nxp.com>
Sean Anderson [Tue, 30 Aug 2022 20:54:39 +0000 (16:54 -0400)]
ddr: fsl: Reduce the size of interactive options
The interactive mode uses large several tables of options which can be
configured. However, much of the contents of these tables are
repetetive. For example, no struct is larger than half a kilobyte, so
the offset only takes up 9 bits. Similarly, the size is only ever 4 or
8, and printhex is a boolean. Reduce the size of these fields. This
reduces the size of the options tables by around 10 KiB. However, the
largest contributor to the size of the options tables is the use of a
pointer for the strings. A better approach would be to use a separate
array of strings, and store an integer index in the options tables.
However, this would require a large re-architecting of this file.
Signed-off-by: Sean Anderson <sean.anderson@seco.com> Signed-off-by: Peng Fan <peng.fan@nxp.com>
Michael Walle [Tue, 23 Aug 2022 09:30:17 +0000 (11:30 +0200)]
board: sl28: support dynamic prompts
Depending on the boot source, set different CLI prompts. This will help
the user to figure out in which mode the bootloader was started. There
are two special modes: failsafe and SDHC boot.
Signed-off-by: Michael Walle <michael@walle.cc> Signed-off-by: Peng Fan <peng.fan@nxp.com>
Michael Walle [Tue, 23 Aug 2022 09:30:14 +0000 (11:30 +0200)]
armv8: layerscape: spl: mark OCRAM as non-secure
By default the OCRAM is marked as secure. While the SPL runs in EL3 and
thus can access it, DMA devices cannot. Mark the whole OCRAM as
non-secure.
This will fix MMC and SD card boot on LS1028A when using SPL instead of
TF-A.
Signed-off-by: Michael Walle <michael@walle.cc> Signed-off-by: Peng Fan <peng.fan@nxp.com>
Jessica Clarke [Fri, 12 Aug 2022 17:50:03 +0000 (18:50 +0100)]
riscv: dts: Sync important Unmatched pmic and qspi0 changes from Linux
This adds the onkey, RTC and watchdog children to the DA9063 PMIC node,
fixes the compatible for qspi0's flash node to match the official DT
schema (it being an is25wp256 is discoverable, hence jedec,spi-nor is
the only compatible that should be present) and exposes the card detect
GPIO.
Note that the device trees still diverge in some places (including
important things like the PCIe controller's clock name) and should be
cleaned up so that a common device tree is used in both projects rather
than having different bindings. This patch does not attempt to do that,
merely expose important functionality present in Linux's that is not in
U-Boot's so that it can be used without the OS providing its own bundled
copy.
Signed-off-by: Jessica Clarke <jrtc27@jrtc27.com> Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
rockchip: allow to build SPI images even without HAS_ROM option
This prepares for the creation of a u-boot-rockchip-spi.bin image
similar to u-boot-rockchip.bin to the exception it's destined for
SPI-NOR flashes instead of MMC storage medium.
Cc: Quentin Schulz <foss+uboot@0leil.net> Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
rockchip: remove binman temporary files when cleaning
Binman mkimage entry generates temporary files so let's remove them
when calling `make clean`.
Fixes: 9b312e26fc77 ("rockchip: Enable building a SPI ROM image on jerry") Cc: Quentin Schulz <foss+uboot@0leil.net> Reported-by: Johan Jonker <jbx6244@gmail.com> Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
binman: add support for skipping file concatenation for mkimage
Some image types handled by mkimage require the datafiles to be passed
independently (-d data1:data2) for specific handling of each. A
concatenation of datafiles prior to passing them to mkimage wouldn't
work.
That is the case for rkspi for example which requires page alignment
and only writing 2KB every 4KB.
This adds the ability to tell binman to pass the datafiles without
prior concatenation to mkimage, by adding the multiple-data-files
boolean property to the mkimage node.
rockchip: rk3399: sync spl_boot_devices_tbl and boot_devices node paths
While technically not a bug, let's have some consistency in paths
returned by u-boot,spl-boot-order look-up and the one saved in
u-boot,spl-boot-device by syncing spl_boot_devices_tbl and boot_devices
node paths.
rockchip: rk3399: fix incorrect boot-device in u-boot, spl-boot-device
On RK3399, mmc0 is eMMC and mmc1 is SD card, c.f. console:
MMC: mmc@fe320000: 1, mmc@fe330000: 0
In arch/arm/mach-rockchip/spl-boot-order.c:board_boot_order, the
boot_device (BOOT_DEVICE_*) value is gotten from spl_node_to_boot_device
function. Said function returns BOOT_DEVICE_MMC1 for mmc0 (eMMC) and
BOOT_DEVICE_MMC2 for mmc1 (SD card).
Since the SD card controller is at mmc@fe320000, it should be associated
with BOOT_DEVICE_MMC2 and not BOOT_DEVICE_MMC1. Same applies to eMMC.
John Keeping [Thu, 14 Jul 2022 14:18:37 +0000 (15:18 +0100)]
rockchip: rk3308: fix same-as-spl boot order
Rockchip SoCs need the boot_devices array defined in order to map the
bootloader's value to a U-Boot device. Implement this for rk3308.
Signed-off-by: John Keeping <john@metanate.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@vrull.eu> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
John Keeping [Thu, 14 Jul 2022 14:09:12 +0000 (15:09 +0100)]
rockchip: rk3308: fix rockchip_dnl_key_pressed() on roc-cc
Commit 6aa4fe3912 ("dm: core: Rename and fix uclass_get_by_name_len()")
changed uclass_get_device_by_name() to an exact match when previously it
behaved as a prefix match.
The roc-cc code relied on this prefix match by only specifying part of
the device name. Fix this by using the full name including the address.
Signed-off-by: John Keeping <john@metanate.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
rockchip: rk3399: boot_devices: fix eMMC node name
When idbloader.img is flashed on the eMMC, the SPL still tries to load
from SPI-NOR first.
This is due to an incorrect look-up in the Device Tree. Since commit 822556a93459 ("arm: dts: sync the Rockhip 3399 SoCs from Linux"), the
node name (but not label) changed from sdhci@fe330000 to mmc@fe330000
meaning U-Boot SPL is not looking for the correct node name anymore and
fails to find the "same-as-spl" node when eMMC is the medium from which
the SPL booted.
Lee Jones [Thu, 11 Aug 2022 07:58:48 +0000 (08:58 +0100)]
ram: rk3399: Conduct memory training at 400MHz
Currently the default initialisation frequency is 50MHz. Although
this does appear to be suitable for some LPDDR4 RAM chips, training at
this low frequency has been seen to cause Column errors, leading to
Capacity check errors on others.
Here we force RAM initialisation to happen at 400MHz before ramping up
to the final value running value of 800MHz after everything has been
successfully configured.
Link: https://lore.kernel.org/u-boot/Yo4v3jUeHXTovjOH@google.com/ Suggested-by: YouMin Chen <cym@rock-chips.com> Signed-off-by: Lee Jones <lee@kernel.org> Tested-by: Xavier Drudis Ferran <xdrudis@tinet.cat> Reviewed-by: Kever Yang <kever.yang@rock-chips.com> Tested-by: Michal Suchánek <msuchanek@suse.de>
Johan Jonker [Mon, 2 May 2022 09:42:22 +0000 (11:42 +0200)]
arm: dts: rockchip: rk3288: rename mmc nodenames
The boot_devices constants for rk3288 were changed to match the
binding, but the dtsi file was not synced.
Fix by renaming the rk3288 mmc node names.
Also correct the clock name for "ciu-drive".
Signed-off-by: Johan Jonker <jbx6244@gmail.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Simon Glass [Wed, 31 Aug 2022 03:05:38 +0000 (21:05 -0600)]
tpm: Allow committing non-volatile data
Add an option to tell the TPM to commit non-volatile data immediately it
is changed, rather than waiting until later. This is needed in some
situations, since if the device reboots it may not write the data.
Add definitions for the rest of the Cr50 commands while we are here.