Sjoerd Simons [Sun, 30 Aug 2015 22:55:44 +0000 (16:55 -0600)]
doc: Fix reference to Rock pro when Rock 2 is meant
The Radxa Rock pro board is rk3188 based and thus won't work with U-Boot
built for RK3288. Change the documentation to refer to the intended
board, the Radxa Rock 2, which is an RK3288-based design very similar to
the firefly
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk> Acked-by: Simon Glass <sjg@chromium.org> Signed-off-by: Simon Glass <sjg@chromium.org>
Simon Glass [Sun, 30 Aug 2015 22:55:41 +0000 (16:55 -0600)]
rockchip: Add basic support for firefly-rk3288
The Firefly RK3288 is a suitable target board for initial mainline Rockchip
support. It includes a good set of peripherals, a recent SoC and it is
readily available.
This adds only some basic files required to allow the baord to display a
serial message in SPL and hang.
Simon Glass [Sun, 30 Aug 2015 22:55:36 +0000 (16:55 -0600)]
rockchip: rk3288: Add SDRAM init
Add code to set up the SDRAM in SPL, ready for loading U-Boot. This uses
device tree for configuration so should be able to support other RAM
configurations. It may be possible to generalise the code to support other
SoCs at some point.
Simon Glass [Sun, 30 Aug 2015 22:55:29 +0000 (16:55 -0600)]
power: Add support for ACT8846 PMIC
Add a driver for the ACT8846 PMIC. This supports several LDOs and BUCKs and
is connected to the I2C bus. This driver supports using a regulator driver
to access the regulators.
Simon Glass [Sun, 30 Aug 2015 22:55:28 +0000 (16:55 -0600)]
rockchip: Add basic peripheral and clock definitions
Add header files for the peripherals and clocks supported on Rockchip
platforms. The particular implementation (and register set) for each is
SoC-specific, but it seems that the naming can be generic.
Simon Glass [Sun, 30 Aug 2015 22:55:26 +0000 (16:55 -0600)]
rockchip: Add support for the SPI image
The Rockchip boot ROM requires a particular file format for booting from SPI.
It consists of a 512-byte header encoded with RC4, some padding and then up
to 32KB of executable code in 2KB blocks, separated by 2KB empty blocks.
Add support to mkimage so that an SPL image (u-boot-spl-dtb.bin) can be
converted to this format. This allows booting from SPI flash on supported
machines.
Simon Glass [Sun, 30 Aug 2015 22:55:25 +0000 (16:55 -0600)]
rockchip: Add support for the SD image
The Rockchip boot ROM requires a particular file format. It consists of
64KB of zeroes, a 512-byte header encoded with RC4, and then some executable
code.
Add support to mkimage so that an SPL image (u-boot-spl-dtb.bin) can be
converted to this format.
Simon Glass [Sun, 30 Aug 2015 22:55:24 +0000 (16:55 -0600)]
rockchip: Add the rkimage format to mkimage
Rockchip SoCs require certain formats for code that they execute, The
simplest format is a 4-byte header at the start of a binary file. Add
support for this so that we can create images that the boot ROM understands.
Simon Glass [Sun, 30 Aug 2015 22:55:20 +0000 (16:55 -0600)]
rockchip: Bring in RK3288 device tree file includes and bindings
Bring in required device tree files from Linux. Since mainline Linux is
somewhat behind, use the files from the Chromium tree. We can re-sync once
further code is acccepted upstream.
Simon Glass [Sun, 30 Aug 2015 22:55:17 +0000 (16:55 -0600)]
dm: Provide better debugging when a device fails to bind
All devices should bind without error. But when they don't, they can cause
driver model init to fail. A real situation where this can happen is when
there is a missing uclass.
Add a debug() call to dm_scan_fdt_node to make this easier to track.
Simon Glass [Sun, 30 Aug 2015 22:55:16 +0000 (16:55 -0600)]
dm: Improve handling of a missing uclass
When a uclass definition is missing, no drivers in that uclass can operate.
This can happen if a board has a strange collection of options (e.g. the
driver is enabled but the uclass is not).
Unfortunately this is very confusing at present. Starting up driver model
results in a -ENOENT error, which is pretty generic. Quite a big of digging
is needed to get to the root cause.
To help with this, change the error to a very strange one with no other
users in U-Boot. Also add a debug message.
Simon Glass [Sun, 30 Aug 2015 22:55:15 +0000 (16:55 -0600)]
mmc: Support bypass mode with the get_mmc_clk() method
Some SoCs want to adjust the input clock to the DWMMC block as a way of
controlling the MMC bus clock. Update the get_mmc_clk() method to support
this.
Signed-off-by: Simon Glass <sjg@chromium.org> Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Simon Glass [Sun, 30 Aug 2015 22:55:14 +0000 (16:55 -0600)]
dm: led: Tidy up SPL options for the led and led-gpio
At present SPL does not have its own option. But these features can
increase SPL code size. Adjust the Kconfig and Makefile so that
separate a SPL option can be selected.
Simon Glass [Sun, 30 Aug 2015 22:55:13 +0000 (16:55 -0600)]
pinctrl: Add the concept of peripheral IDs
My original pinctrl patch operating using a peripheral ID enum. This was
shared between pinmux and clock and provides an easy way to specify a device
that needs to be controlled, even it is does not (yet) have a driver within
driver model.
Masahiro's new simple pinctrl gets around this by providing a
set_state_simple() pinctrl method. By passing a device to that call the
peripheral ID becomes unnecessary. If the driver needs it, it can calculate
it itself and use it internally.
However this does not solve the problem for peripheral clocks. The 'pure'
solution would be to pass a driver to the clock uclass also. But this
requires that all devices should have a driver, and a struct udevide. Also
a key optimisation of the clock uclass is allowing a peripheral clock to
be set even when there is no device for that clock.
There may be a better way to achive the same goal, but for now it seems
expedient to add in peripheral ID to the pinctrl uclass. Two methods are
added - one to get the peripheral ID and one to select it. The existing
set_state_simple() is effectively the union of these.
Boris Brezillon [Mon, 27 Jul 2015 14:21:26 +0000 (16:21 +0200)]
sunxi: increase SYS_MONITOR_LEN
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Masahiro Yamada [Thu, 27 Aug 2015 03:44:29 +0000 (12:44 +0900)]
pinctrl: add pin control uclass support
This creates a new framework for handling of pin control devices,
i.e. devices that control different aspects of package pins.
This uclass handles pinmuxing and pin configuration; pinmuxing
controls switching among silicon blocks that share certain physical
pins, pin configuration handles electronic properties such as pin-
biasing, load capacitance etc.
This framework can support the same device tree bindings, but if you
do not need full interface support, you can disable some features to
reduce memory foot print. Typically around 1.5KB is necessary to
include full-featured uclass support on ARM board (CONFIG_PINCTRL +
CONFIG_PINCTRL_FULL + CONFIG_PINCTRL_GENERIC + CONFIG_PINCTRL_PINMUX),
for example.
We are often limited on code size for SPL. Besides, we still have
many boards that do not support device tree configuration. The full
pinctrl, which requires OF_CONTROL, does not make sense for those
boards. So, this framework also has a Do-It-Yourself (let's say
simple pinctrl) interface. With CONFIG_PINCTRL_FULL disabled, the
uclass itself provides no systematic mechanism for identifying the
peripheral device, applying pinctrl settings, etc. They must be
done in each low-level driver. In return, you can save much memory
footprint and it might be useful especially for SPL.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Acked-by: Simon Glass <sjg@chromium.org>
Simon Glass [Sun, 23 Aug 2015 00:31:42 +0000 (18:31 -0600)]
dm: tpm: Add a 'tpmtest' command
These tests come from Chrome OS code. They are not particularly tidy but can
be useful for checking that the TPM is behaving correctly. Some knowledge of
TPM operation is required to use these.
Simon Glass [Sun, 23 Aug 2015 00:31:33 +0000 (18:31 -0600)]
dm: i2c: Add a command to adjust the offset length
I2C chips can support a register offset, with registers accessible by
sending this offset as the first part of any read or write transaction.
Most I2C chips have a single byte offset, thus the offset length is 1.
This provides access for up 256 registers.
However other offset lengths are supported, including 0.
Add a command to provide access to the offset length from the command
line. This allows the offset length to be read or written.
Simon Glass [Sun, 23 Aug 2015 00:31:31 +0000 (18:31 -0600)]
dm: tpm: Add a uclass for Trusted Platform Modules
Add a new uclass for TPMs which uses almost the same TIS (TPM Interface
Specification) as is currently implemented. Since init() is handled by the
normal driver model probe() method, we don't need to implement that. Also
rename the transfer method to xfer() which is a less clumbsy name.
Once all drivers and users are converted to driver model we can remove the
old code.
Simon Glass [Sun, 23 Aug 2015 00:31:30 +0000 (18:31 -0600)]
tpm: tpm_tis_i2c: Tidy up delays
Use a _US suffix for microseconds and a _MS suffic for milliseconds. Move
all timeouts and delays into one place. Use mdelay() instead of udelay()
where appropriate.
Simon Glass [Sun, 23 Aug 2015 00:31:25 +0000 (18:31 -0600)]
tpm: tpm_tis_i2c: Merge struct tpm_dev into tpm_chip
There are too many structures storing the same sort of information. Move the
fields from struct tpm_dev into struct tpm_chip and remove the former
struct.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Heiko Schocher <hs@denx.de>
Simon Glass [Sun, 23 Aug 2015 00:31:22 +0000 (18:31 -0600)]
tpm: Move the I2C TPM code into one file
The current Infineon I2C TPM driver is written in two parts, intended to
support use with other I2C devices. However we don't have any users and the
Atmel I2C TPM device does not use this file.
We should simplify this and remove the unused abstration. As a first step,
move the code into one file.
Also the name tpm_private.h suggests that the header file is generic to all
TPMs but it is not. Rename it indicate that it relates only to this driver
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Heiko Schocher <hs@denx.de>
Marek Vasut [Sun, 2 Aug 2015 23:15:48 +0000 (01:15 +0200)]
dm: core: Add Kconfig for simple bus driver
Add Kconfig entries for the simple-bus driver, both for U-Boot
and for SPL. The simple-bus is enabled by default in U-Boot and
disabled by default in SPL to preserve the original behavior.
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Simon Glass <sjg@chromium.org> Acked-by: Simon Glass <sjg@chromium.org>
Modified to fit on top of Masahiro's $(SPL) setup: Signed-off-by: Simon Glass <sjg@chromium.org>
Simon Glass [Tue, 11 Aug 2015 14:33:29 +0000 (08:33 -0600)]
dm: Use dev_get_addr() where possible
This is a convenient way for a driver to get the hardware address of a
device, when regmap or syscon are not being used. Change existing callers
to use it as an example to others.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Joe Hershberger <joe.hershberger@ni.com> Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Yousong Zhou [Sat, 29 Aug 2015 13:26:11 +0000 (21:26 +0800)]
sunxi: mmc: set transfer timeout according to byte_cnt.
Originally a timeout value of 2 seconds was used regardless of the size
of data to be transfered. This prevented slow devices from working
correctly while there was no much gain for faster devices, e.g. it takes
3708ms for a transfer of uImage of size 1899008 bytes.
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Chen-Yu Tsai [Tue, 25 Aug 2015 02:49:19 +0000 (10:49 +0800)]
sunxi: Enable non-secure access to RTC on sun6i (A31s)
On the A31s the RTC is by default secured. Thus when u-boot
loads the kernel in non-secure world, the RTC is unavailable. The
SoC has a TrustZone Protection Controller, which can be used to
enable non-secure access to the RTC.
On the A31 the TZPC doesn't seem to do anything, i.e. changes to
its register contents do not affect access to the RTC.
Signed-off-by: Chen-Yu Tsai <wens@csie.org> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Hans de Goede [Tue, 25 Aug 2015 12:20:49 +0000 (14:20 +0200)]
sunxi: Add inet98v_rev2 defconfig and dts file
The inet98v_rev2 is a pcb used in generic A13 based tablets. It features
volume buttons, a power barrel, micro-usb otg, headphone connector and
a power button.
The dts file is identical to the one submitted to the upstream kernel.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
Hans de Goede [Fri, 21 Aug 2015 19:49:51 +0000 (21:49 +0200)]
mtd: nand: Make CONFIG_SYS_NAND_U_BOOT_OFFS configurable through Kconfig
Make CONFIG_SYS_NAND_U_BOOT_OFFS configurable through Kconfig, just like
SYS_NAND_BUSWIDTH_16BIT this is only enabled on some SoCs using depends,
to avoid double defining it for SoCs which have not yet moved to Kconfig
for this.
Having this in Kconfig is useful because this is something which may
differ from one board to the other even when using the same SoC.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk> Acked-by: Scott Wood <scottwood@freescale.com>
Boris Brezillon [Sat, 29 Aug 2015 10:29:38 +0000 (12:29 +0200)]
sunxi_nand_spl: clear status flags in SPL implementation
Some status flags remain set until you explicetly clear the bit
in the status register.
Fix the SPL implementation to avoid false positive.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
[hdegoede@redhat.com: Port from v2015.07 to v2015.10] Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
We only ever use syndrome mode for the partitions which contain the SPL,
as that is required for the BROM to be able to read the SPL.
Instead of using some arbritray limit for deciding whether or not to
use syndrome, be smart and check if u-boot-dtb.bin is directly behind
the SPL, if it is not then it is on its own partition and we should not
use syndrome.
Note the reason why we only use syndrome mode for the SPL is because it
comeswith weaker randomization, introducing a risk for more bit errors,
so we want to avoid it when possible.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
Hans de Goede [Sun, 16 Aug 2015 12:48:22 +0000 (14:48 +0200)]
sunxi_nand_spl: Rename SPL_NAND_SUNXI to NAND_SUNXI
We eventually want to add full nand support, since it makes no sense
to build SPL with nand support and u-boot without, or the other way
around, a single option will suffice.
Renaming the Kconfig option now makes things easier when we add full
nand support in the future.
The "obj-$(CONFIG_NAND_SUNXI) += sunxi_nand_spl.o" is moved to an
"ifdef CONFIG_SPL_BUILD" block in the Makefile.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
Hans de Goede [Sat, 15 Aug 2015 19:51:33 +0000 (21:51 +0200)]
sunxi_nand_spl: Add support for backup boot partitions
The BROM does not care / use bad page markings, instead it deals with
any bad pages in the first erase-block by simply trying to load "boot0"
from the next erase-block.
This commit implements the same strategy for the sunxi spl nand code,
allowing it to boot from the backup boot partition when the main boot
partition is bad (tested by erasing the main boot partition).
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
Hans de Goede [Sat, 15 Aug 2015 19:23:08 +0000 (21:23 +0200)]
sunxi_nand_spl: Auto detect nand configuration parameters
Auto detect the nand configuration parameters, like the BROM does.
This allows us to get rid of various Kconfig settings, and is
necessary to support generic boards like the mk802 which have seen
many production runs with different nands.
The full blown u-boot/kernel nand driver uses the nand id to determine
this info, for the SPL we do as the BROM does and simply try a few
standard configs.
Note the table only contains configs which are known to actually be used,
rather then all the configs the BROM tries. This means that it may need
to be updated in the future as we add support for nand on more boards.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
Parametrize the lowlevel nand_read_page function, instead of directly
using the CONFIG_foo settings for page-size, etc. there and add a few
wrappers / helper functions for calling it.
This is a preparation patch for adding auto-detecting of the nand
parameters like the BROM does.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
Hans de Goede [Sat, 15 Aug 2015 18:05:13 +0000 (20:05 +0200)]
sunxi_nand_spl: Properly config page-size in the nand ctl register
Properly config page-size in the nand ctl register, it seems that things
work fine without doing this, but still lets play it safe and properly
set the page-size.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
Hans de Goede [Sat, 15 Aug 2015 11:17:49 +0000 (13:17 +0200)]
sunxi_nand_spl: Add support for sun4i and sun5i SoCs
Other then having a few less chip-select lines the nand controller
on sun4i, sun5i and sun7i is identical.
Note this patch also muxes GPC7 to the NAND on sun7i where as before
it was not muxed this way. GPC7 is a standard NAND pin, so it should
always be muxed to the NAND when in use.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
Hans de Goede [Sat, 15 Aug 2015 10:41:09 +0000 (12:41 +0200)]
sunxi_nand_spl: Use kernel driver algorithm for determining ecc_mode / _off
Sync the code for figuring out the ecc_mode and ecc_offset with the linux
kernel v4.1. Keeping this in sync seems like a good idea in general, and
it fixes / adds support for ecc strengths of 56, 60 and 64 bits.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
Hans de Goede [Sat, 15 Aug 2015 09:59:25 +0000 (11:59 +0200)]
sunxi_nand_spl: Turn off clocks when we're done with the nand
Turn off the nand and dma clocks when we're done with the nand, this
puts the nand and dma controllers back into a clean state for when the
kernel boots.
Without this the kernel will not boot properly when it is built with
dma-controller support.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
Hans de Goede [Sat, 15 Aug 2015 10:43:26 +0000 (12:43 +0200)]
sunxi_nand_spl: Do not bother writing the spare-area reg in syndrome mode
In syndrome mode we set the NFC_SEQ bit in the command register, so the
spare-area register is not used. Also the value currently being written is
actual wrong, the ecc sits at "column + CONFIG_NAND_SUNXI_SPL_ECC_PAGE_SIZE"
not just CONFIG_NAND_SUNXI_SPL_ECC_PAGE_SIZE.
So the current code only serves to confuse the user -> remove it.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
projects / u-boot.git / log