arm: Implement show_boot_progress() for imx53's HSC and DDC devices
This patch provides information regarding the boot stage with using LEDs.
On the very beginning of U-Boot execution the GREEN LED is turned on.
When the execution is passed to Linux kernel the GREEN LED is off and
RED one is ON.
Afterwards, when Linux takes over the execution, the "heartbeat" driver
provides indication if the board is still alive.
Please also note that this patch uses {set|clr}bits_le32 macros as turning
ON GREEN LED is performed in a _very_ early stage of U-Boot execution
before DM_GPIOs are initialized.
In order to be able to run the I2C bus at 400Khz, the chip errata[1]
recommends that the peripheral clock runs out of the 24MHz oscillator.
Systems running I2C from OP-TEE before Linux executes - for example to
access a Secure Element [2] providing the cryptographic support - expect
this clock to be configured by the bootloader [3].
[1] IMX6SLCE Rev. 5, 02/2019, ERR007805.
[2] OP-TEE: support for NXP SE05X Plug and Trust (patch on the list).
[3] OP-TEE: check the imx_i2c.c driver (imx6 patch on the list).
Peng Fan [Wed, 14 Oct 2020 09:11:59 +0000 (17:11 +0800)]
board: imx: address dd usage in README
When using cygwin64 "dd (coreutils) 8.26 Packaged by Cygwin (8.26-2)",
the last not 512bytes aligned data wat cut off and not burned into SD
card.
Saying the flash.bin size is 1085608 bytes, not 512bytes aligned. It only
burned 1085440 bytes, the leaving 168 bytes were not burnned and cause
boot issue.
Tom Rini [Sat, 31 Oct 2020 02:55:16 +0000 (22:55 -0400)]
Merge tag 'u-boot-rockchip-20201031' of https://gitlab.denx.de/u-boot/custodians/u-boot-rockchip
- New PX30 board: Engicam PX30.Core;
- Fix USB HID support for rock960;
- Remove host endianness dependency for rockchip mkimage;
- dts update for rk3288-tinker;
- Enable console MUX for some ROCKPi boards;
- Add config-based ddr selection for px30;
Jagan Teki [Wed, 28 Oct 2020 13:33:44 +0000 (19:03 +0530)]
board: engicam: Attach i.MX6 common code
The existing common code for Engicam boards uses i.MX6,
so attach that into i.MX6 Engicam boards so-that adding
new SoC variants of Engicam boards become meaningful.
PX30.Core is an EDIMM SOM based on Rockchip PX30 from Engicam.
General features:
- Rockchip PX30
- Up to 2GB DDR4
- eMMC 4 GB expandible
- rest of PX30 features
PX30.Core needs to mount on top of Engicam baseboards for creating
complete platform boards.
Possible baseboards are,
- EDIMM2.2
- C.TOUCH 2.0
Add support for it.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Engicam EDIMM2.2 Starter Kit is an EDIMM 2.2 Form Factor Capacitive
Evaluation Board.
Genaral features:
- LCD 7" C.Touch
- microSD slot
- Ethernet 1Gb
- Wifi/BT
- 2x LVDS Full HD interfaces
- 3x USB 2.0
- 1x USB 3.0
- HDMI Out
- Mini PCIe
- MIPI CSI
- 2x CAN
- Audio Out
SOM's like PX30.Core needs to mount on top of this Evaluation board
for creating complete PX30.Core EDIMM2.2 Starter Kit.
Add support for it.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The Rockchip boot ROM expects little-endian values in the image header.
When running mkimage on a big-endian machine, these values need to be
byteswapped before writing or verifying the header.
This change fixes cross-compiling U-Boot SPL for the RK3399 SoC from a
big-endian ppc64 host machine.
Signed-off-by: Samuel Holland <samuel@sholland.org> Reviewed-by: Kever Yang<kever.yang@rock-chips.com>
Sean Anderson [Tue, 27 Oct 2020 23:55:41 +0000 (19:55 -0400)]
doc: Update logging documentation
This updates logging documentation with some examples of the new commands
added in the previous commits. It also removes some items from the to-do
list which have been implemented.
Signed-off-by: Sean Anderson <seanga2@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Sean Anderson [Tue, 27 Oct 2020 23:55:39 +0000 (19:55 -0400)]
test: Add a test for log filter-*
This exercises a few success and failure modes of the log filter-*
commands. log filter-list is not tested because it's purely informational.
I don't think there's a good way to test it except by testing if the output
of the command exactly matches a sample run.
Signed-off-by: Sean Anderson <seanga2@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Sean Anderson [Tue, 27 Oct 2020 23:55:38 +0000 (19:55 -0400)]
cmd: log: Add commands to manipulate filters
This adds several commands to add, list, and remove log filters. Due to the
complexity of adding a filter, `log filter-list` uses options instead of
positional arguments.
These commands have been added as subcommands to log by using a dash to
join the subcommand and subsubcommand. This is stylistic, and they could be
converted to proper subsubcommands if it is wished.
Signed-off-by: Sean Anderson <seanga2@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Sean Anderson [Tue, 27 Oct 2020 23:55:37 +0000 (19:55 -0400)]
test: Add a test for getopt
A few of these tests were inspired by those in glibc. The syntax for
invoking test_getopt is a bit funky, but it's necessary so that the CPP can
parse the arguments correctly.
Sean Anderson [Tue, 27 Oct 2020 23:55:36 +0000 (19:55 -0400)]
lib: Add getopt
Some commands can get very unweildy if they have too many positional
arguments. Adding options makes them easier to read, remember, and
understand.
This implementation of getopt has been taken from barebox, which has had
option support for quite a while. I have made a few modifications to their
version, such as the removal of opterr in favor of a separate getopt_silent
function. In addition, I have moved all global variables into struct
getopt_context.
The getopt from barebox also re-orders the arguments passed to it so that
non-options are placed last. This allows users to specify options anywhere.
For example, `ls -l foo/ -R` would be re-ordered to `ls -l -R foo/` as
getopt parsed the options. However, this feature conflicts with the const
argv in cmd_tbl->cmd. This was originally added in 54841ab50c ("Make sure
that argv[] argument pointers are not modified."). The reason stated in
that commit is that hush requires argv to stay unmodified. Has this
situation changed? Barebox also uses hush, and does not have this problem.
Perhaps we could use their fix?
I have assigned maintenance of getopt to Simon Glass, as it is currently
only used by the log command. I would also be fine maintaining it.
Sean Anderson [Tue, 27 Oct 2020 23:55:35 +0000 (19:55 -0400)]
cmd: log: Make "log level" print all log levels
This makes the log level command print all valid log levels. The default
log level is annotated. This provides an easy way to see which log levels
are compiled-in.
Signed-off-by: Sean Anderson <seanga2@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Sean Anderson [Tue, 27 Oct 2020 23:55:34 +0000 (19:55 -0400)]
cmd: log: Add commands to list categories and drivers
This allows users to query which categories and drivers are available on
their system. This allows them to construct filter-add commands without
(e.g.) adjusting the log format to show categories and drivers.
Signed-off-by: Sean Anderson <seanga2@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Sean Anderson [Tue, 27 Oct 2020 23:55:33 +0000 (19:55 -0400)]
cmd: log: Split off log level parsing
Move parsing of log level into its own function so it can be re-used. This
also adds support for using log level names instead of just the integer
equivalent.
Signed-off-by: Sean Anderson <seanga2@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Sean Anderson [Tue, 27 Oct 2020 23:55:30 +0000 (19:55 -0400)]
log: Add filter flag to match greater than a log level
This is the complement of the existing behavior to match only messages with
a log level less than a threshold. This is primarily useful in conjunction
with LOGFF_DENY.
Signed-off-by: Sean Anderson <seanga2@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Sean Anderson [Tue, 27 Oct 2020 23:55:27 +0000 (19:55 -0400)]
test: log: Convert log_test from python to C
When rebasing this series I had to renumber all my log tests because
someone made another log test in the meantime. This involved updaing a
number in several places (C and python), and it wasn't checked by the
compiler. So I though "how hard could it be to just rewrite in C?" And
though it wasn't hard, it *was* tedious. Tests are numbered the same as
before to allow for easier review.
A note that if a test fails, everything after it will probably also fail.
This is because that test won't clean up its filters. There's no easy way
to do the cleanup, except perhaps removing all filters in a wrapper
function.
Sean Anderson [Tue, 27 Oct 2020 23:55:26 +0000 (19:55 -0400)]
log: Add filter flag to deny on match
Without this flag, log filters can only explicitly accept messages.
Allowing denial makes it easier to filter certain subsystems. Unlike
allow-ing filters, deny-ing filters are added to the beginning of the
filter list. This should do the Right Thing most of the time, but it's
less-universal than allowing filters to be inserted anywhere. If this
becomes a problem, then perhaps log_filter_add* should take a filter number
to insert before/after.
Signed-off-by: Sean Anderson <seanga2@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Sean Anderson [Tue, 27 Oct 2020 23:55:21 +0000 (19:55 -0400)]
log: Fix incorrect documentation of log_filter.cat_list
Logging category lists are terminated by LOGC_END, not LOGC_NONE.
Fixes: e9c8d49d54 ("log: Add an implementation of logging") Signed-off-by: Sean Anderson <seanga2@gmail.com> Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Sean Anderson [Tue, 27 Oct 2020 23:55:20 +0000 (19:55 -0400)]
log: Fix missing negation of ENOMEM
Errors returned should be negative.
Fixes: 45fac9fc18 ("log: Correct missing free() on error in log_add_filter()") Signed-off-by: Sean Anderson <seanga2@gmail.com> Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Heiko Schocher [Sat, 10 Oct 2020 08:28:06 +0000 (10:28 +0200)]
imx6: enable early spi environment access on aristainetos boards
On aristianetos boards the display type is detected
through "panel" environment variable. Dependend on the
display type we detect the board type and this decides which
DTB we have to use for the board.
Heiko Schocher [Sat, 10 Oct 2020 08:28:05 +0000 (10:28 +0200)]
env: Access Environment in SPI flashes before relocation
Enable the new Kconfig option ENV_SPI_EARLY if you want
to use Environment in SPI flash before relocation.
Call env_init() and than you can use env_get_f() for
accessing Environment variables.
Signed-off-by: Heiko Schocher <hs@denx.de> Reviewed-by: Simon Glass <sjg@chromium.org>
Heiko Schocher [Sat, 10 Oct 2020 08:28:04 +0000 (10:28 +0200)]
env: split env_import_redund() into 2 functions
split from env_import_redund() the part which checks
which Environment is valid into a separate function
called env_check_redund() and call it from env_import_redund().
So env_check_redund() can be used from places which also
need to do this checks.
Signed-off-by: Heiko Schocher <hs@denx.de> Reviewed-by: Simon Glass <sjg@chromium.org>
video: rockchip: Add missing dpcd_write() call to link_train_ce()
Found this by comparing it to the coreboot driver, a form of this call
was introduced there in their commit b9a7877568cf ("rockchip/*: refactor
edp driver"). This is copy-pasted from U-Boot's link_train_cr() slightly
above it.
Without this on a gru-kevin chromebook, I have:
clock recovery at voltage 0 pre-emphasis 0
requested signal parameters: lane 0 voltage 0.4V pre_emph 3.5dB
requested signal parameters: lane 1 voltage 0.4V pre_emph 3.5dB
requested signal parameters: lane 2 voltage 0.4V pre_emph 3.5dB
requested signal parameters: lane 3 voltage 0.4V pre_emph 3.5dB
using signal parameters: voltage 0.4V pre_emph 3.5dB
requested signal parameters: lane 0 voltage 0.4V pre_emph 3.5dB
requested signal parameters: lane 1 voltage 0.4V pre_emph 3.5dB
requested signal parameters: lane 2 voltage 0.4V pre_emph 3.5dB
requested signal parameters: lane 3 voltage 0.4V pre_emph 3.5dB
using signal parameters: voltage 0.4V pre_emph 3.5dB
requested signal parameters: lane 0 voltage 0.4V pre_emph 3.5dB
requested signal parameters: lane 1 voltage 0.4V pre_emph 3.5dB
requested signal parameters: lane 2 voltage 0.4V pre_emph 3.5dB
requested signal parameters: lane 3 voltage 0.4V pre_emph 3.5dB
using signal parameters: voltage 0.4V pre_emph 3.5dB
requested signal parameters: lane 0 voltage 0.4V pre_emph 3.5dB
requested signal parameters: lane 1 voltage 0.4V pre_emph 3.5dB
requested signal parameters: lane 2 voltage 0.4V pre_emph 3.5dB
requested signal parameters: lane 3 voltage 0.4V pre_emph 3.5dB
using signal parameters: voltage 0.4V pre_emph 3.5dB
requested signal parameters: lane 0 voltage 0.4V pre_emph 3.5dB
requested signal parameters: lane 1 voltage 0.4V pre_emph 3.5dB
requested signal parameters: lane 2 voltage 0.4V pre_emph 3.5dB
requested signal parameters: lane 3 voltage 0.4V pre_emph 3.5dB
using signal parameters: voltage 0.4V pre_emph 3.5dB
channel eq failed, ret=-5
link train failed!
rk_vop_probe() Device failed: ret=-5
With this, it looks like training succeeds:
clock recovery at voltage 0 pre-emphasis 0
requested signal parameters: lane 0 voltage 0.4V pre_emph 3.5dB
requested signal parameters: lane 1 voltage 0.4V pre_emph 3.5dB
requested signal parameters: lane 2 voltage 0.4V pre_emph 3.5dB
requested signal parameters: lane 3 voltage 0.4V pre_emph 3.5dB
using signal parameters: voltage 0.4V pre_emph 3.5dB
requested signal parameters: lane 0 voltage 0.4V pre_emph 6dB
requested signal parameters: lane 1 voltage 0.4V pre_emph 6dB
requested signal parameters: lane 2 voltage 0.4V pre_emph 6dB
requested signal parameters: lane 3 voltage 0.4V pre_emph 6dB
using signal parameters: voltage 0.4V pre_emph 6dB
requested signal parameters: lane 0 voltage 0.4V pre_emph 0dB
requested signal parameters: lane 1 voltage 0.4V pre_emph 0dB
requested signal parameters: lane 2 voltage 0.4V pre_emph 0dB
requested signal parameters: lane 3 voltage 0.4V pre_emph 0dB
using signal parameters: voltage 0.4V pre_emph 0dB
channel eq at voltage 0 pre-emphasis 0
config video failed
rk_vop_probe() Device failed: ret=-110
The "config video failed" error also goes away when I disable higher
log levels, and it claims to have successfully probed the device.
In order to correctly calculate the designware watchdog
timeouts, the watchdog clock is required. Implement required
clocks to facilitate this.
Signed-off-by: Jack Mitchell <ml@embed.me.uk> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Simon Glass [Mon, 26 Oct 2020 23:40:26 +0000 (17:40 -0600)]
binman: Avoid calculated section data repeatedly
Refactor the implementation slightly so that section data is not
rebuilt when it is already available.
We still have GetData() set up to rebuild the section, since we don't
currently track when things change that might affect a section. For
example, if a blob is updated within a section, we must rebuild it.
Tracking that would be possible but is more complex, so it left for
another time.
Simon Glass [Mon, 26 Oct 2020 23:40:25 +0000 (17:40 -0600)]
binman: Support compression of sections
With the previous changes, it is now possible to compress entire
sections. Add some tests to check that compression works correctly,
including updating the metadata.
Simon Glass [Mon, 26 Oct 2020 23:40:24 +0000 (17:40 -0600)]
binman: Use the actual contents in CheckSize()
At present this function adds up the total size of entries to work out the
size of a section's contents. With compression this is no-longer enough.
We may as well bite the bullet and build the section contents instead.
Call _BuildSectionData() to get the (possibly compressed) contents and
GetPaddedData() to get the same but with padding added.
Note that this is inefficient since the section contents is calculated
twice. Future work will improve this.
This affects testPackOverlapMap() since the error is reported with a
different section size now (enough to hold the contents). Update that at
the same time.
Simon Glass [Mon, 26 Oct 2020 23:40:23 +0000 (17:40 -0600)]
binman: Update CheckEntries() for compressed sections
At present this function assumes that the size of a section is at least as
large as its contents. With compression this is often not the case. Relax
this constraint by using the uncompressed size, if available.
Simon Glass [Mon, 26 Oct 2020 23:40:22 +0000 (17:40 -0600)]
binman: Drop CheckEntries()
This method introduces a separation between packing and checking that is
different for sections. In order to handle compression properly, we need
to be able to deal with a section's size being smaller than the
uncompressed size of its contents. It is easier to make this work if
everything happens in the Pack() method.
The only real user of CheckEntries() is entry_Section and it can call it
directly. Drop the call from 'control' and handle it locally.
Simon Glass [Mon, 26 Oct 2020 23:40:21 +0000 (17:40 -0600)]
binman: Call CheckSize() from the section's Pack() method
At present CheckSize() is called from the function that packs the entries.
Move it up to the main Pack() function so that _PackEntries() can just
do the packing.
Simon Glass [Mon, 26 Oct 2020 23:40:19 +0000 (17:40 -0600)]
binman: Move sort and expand to the main Pack() function
At present sorting and expanding entries are side-effects of the
CheckEntries() function. This is a bit confusing, as 'checking' would
not normally involve making changes.
Move these steps into the Pack() function instead.
Simon Glass [Mon, 26 Oct 2020 23:40:17 +0000 (17:40 -0600)]
binman: Avoid reporting image-pos with compression
When a section is compressed, all entries within it are grouped together
into a compressed block of data. This obscures the start of each
individual child entry.
Avoid reporting bogus 'image-pos' properties in this case, since it is
not possible to access the entry at the location provided. The entire
section must be decompressed first.
CBFS does not support compressing whole sections, only individual files,
so needs no special handling here.
Simon Glass [Mon, 26 Oct 2020 23:40:16 +0000 (17:40 -0600)]
binman: Set section contents in GetData()
Section contents is not set up when ObtainContents() is called, since
packing often changes the layout of the contents. Ensure that the contents
are correctly recorded by making this function regenerate the section. It
is normally only called by the parent section (when packing) or by the
top-level image code, when writing out the image. So the performance
impact is fairly small.
Now that sections have their contents in their 'data' property, update
testSkipAtStartSectionPad() to check it.
Simon Glass [Mon, 26 Oct 2020 23:40:14 +0000 (17:40 -0600)]
binman: Make section padding consistent with other entries
At present padding of sections is inconsistent with other entry types, in
that different pad bytes are used.
When a normal entry is padded by its parent, the parent's pad byte is
used. But for sections, the section's pad byte is used.
Adjust logic to always do this the same way.
Note there is still a special case in entry_Section.GetPaddedData() where
an image is padded with the pad byte of the top-level section. This is
necessary since otherwise there would be no way to set the pad byte of
the image, without adding a top-level section to every image.
Simon Glass [Mon, 26 Oct 2020 23:40:13 +0000 (17:40 -0600)]
binman: Move section padding to the parent
Each section is padded up to its size, if the contents are not large
enough. Move this logic from _BuildSectionData() to
GetPaddedDataForEntry() so that all the padding is in one place.
With this, the testDual test is working again, so enable it.
Simon Glass [Mon, 26 Oct 2020 23:40:12 +0000 (17:40 -0600)]
binman: Refactor _BuildSectionData()
At present this function does the padding needed around an entry. It is
easier to understand what is going on if we have a function that returns
the contents of an entry, with padding included.
Refactor the code accordingly, adding a new GetPaddedData() method.
Simon Glass [Mon, 26 Oct 2020 23:40:10 +0000 (17:40 -0600)]
binman: Expand docs and test for alignment
Alignment does form part of the entry once the image is written out, but
within binman the entry contents does not include the padding. Add
documentation to make this clear, as well as a test.
Simon Glass [Mon, 26 Oct 2020 23:40:09 +0000 (17:40 -0600)]
binman: Expand docs and test for padding
Padding becomes part of the entry once the image is written out, but
within binman the entry contents does not include the padding. Add
documentation to make this clear, as well as a test.
Simon Glass [Mon, 26 Oct 2020 23:40:07 +0000 (17:40 -0600)]
binman: Use 'files-compress' to set compression for files
At present we use 'compress' as the property to set the compression of
a 'files' entry. But this conflicts with the same property for entries,
of which Entry_section is a subclass.
Strictly speaking, since Entry_files is in fact a subclass of
Entry_section, the files can be compressed individually but also the
section (that contains all the files) can itself be compressed. With this
change, it is possible to express that.
Simon Glass [Mon, 26 Oct 2020 23:40:01 +0000 (17:40 -0600)]
binman: Add tests for skip-at-start sections
At present this feature is tested view the end-at-4gb feature. Add some
tests of its own, including the operation of padding.
The third test here shows binman's current, inconsistent approach to
padding in the top-level section. Future patches in this series will
address this.
Simon Glass [Sat, 3 Oct 2020 17:31:41 +0000 (11:31 -0600)]
dm: Don't allow U_BOOT_DEVICE() when of-platdata is used
With of-platdata, the devicetree is supposed to specify all the devices
in the system. So far this hasn't really mattered since of-platdata still
works correctly.
However, new of-platdata features rely on numbering the devices in a
particular order so that they can be referenced by a single integer. It is
tricky to implement this efficiently when other devices are present in the
build.
To address this, disable use of U_BOOT_DEVICE() when of-platdata is
enabled. This seems acceptable as it is not supposed to be used at all,
except in SPL/TPL, where of-platdata is the recommended approach.
This breaks one non-compliant boards at present: mx6cuboxi
Signed-off-by: Simon Glass <sjg@chromium.org>
(disable CONFIG_IMX_THERMAL for mx6cuboxi to avoid a build error)
Simon Glass [Thu, 29 Oct 2020 17:08:25 +0000 (11:08 -0600)]
imx: mx6cuboxi: Disable thermal driver in SPL
This feature is incompatble with of-platdata since it uses the
U_BOOT_DEVICE() macro. With of-platdata the only devices permitted are
those created by dtoc.
The driver is not used in SPL anyway, so exclude it from that build.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Fabio Estevam <festevam@gmail.com>
Simon Glass [Sat, 3 Oct 2020 17:31:40 +0000 (11:31 -0600)]
dm: Use driver_info index instead of pointer
At present we use a 'node' pointer in the of-platadata phandle_n_arg
structs. This is a pointer to the struct driver_info for a particular
device, and we can use it to obtain the struct udevice pointer itself.
Since we don't know the struct udevice pointer until it is allocated in
memory, we have to fix up the phandle_n_arg.node at runtime. This is
annoying since it requires that SPL's data is writable and adds a small
amount of extra (generated) code in the dm_populate_phandle_data()
function.
Now that we can find a driver_info by its index, it is easier to put the
index in the phandle_n_arg structures.
Update dtoc to do this, add a new device_get_by_driver_info_idx() to look
up a device by drive_info index and update the tests to match.
projects / u-boot.git / log