pinctrl: move dm_scan_fdt_node() out of pinctrl uclass
Commit c5acf4a2b3c6 ("pinctrl: Add the concept of peripheral IDs")
added some additional change that was not mentioned in the git-log.
That commit added dm_scan_fdt_node() in the pinctrl uclass binding.
It should be handled by the simple-bus driver or the low-level
driver, not by the pinctrl framework.
I guess Simon's motivation was to bind GPIO banks located under the
Rockchip pinctrl device. It is true some chips have sub-devices
under their pinctrl devices, but it is basically SoC-specific matter.
This commit partly reverts commit c5acf4a2b3c6 to keep the only
pinctrl-generic features in the uclass. The dm_scan_fdt_node()
should be called from the rk3288_pinctrl driver.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Acked-by: Simon Glass <sjg@chromium.org> Tested-by: Simon Glass <sjg@chromium.org>
Bin Meng [Mon, 14 Sep 2015 07:07:41 +0000 (00:07 -0700)]
x86: quark: Configure MTRR to enable cache
Quark SoC does not support MSR MTRRs. Fixed and variable range MTRRs
are accessed indirectly via the message port and not the traditional
MSR mechanism. Only UC, WT and WB cache types are supported.
We configure all the fixed range MTRRs with common values (VGA RAM
as UC, others as WB) and 3 variable range MTRRs for ROM/eSRAM/RAM as
WB, which significantly improves the boot time performance.
With this commit, it takes only 2 seconds for U-Boot to boot to shell
on Intel Galileo board. Previously it took about 6 seconds.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Acked-by: Simon Glass <sjg@chromium.org> Tested-by: Simon Glass <sjg@chromium.org>
Bin Meng [Thu, 10 Sep 2015 06:20:27 +0000 (23:20 -0700)]
x86: quark: Initialize thermal sensor properly
Thermal sensor on Quark SoC needs to be properly initialized per
Quark firmware writer guide, otherwise when booting Linux kernel,
it triggers system shutdown because of wrong temperature in the
thermal sensor is detected by the kernel driver (see below):
[ 5.119819] thermal_sys: Critical temperature reached(206 C),shutting down
[ 5.128997] Failed to start orderly shutdown: forcing the issue
[ 5.135495] Emergency Sync complete
Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Acked-by: Simon Glass <sjg@chromium.org>
This happens when Quark kernel Isolated Memory Region (IMR) driver
tries to lock an IMR register to protect kernel's text and rodata
sections. However in order to have IMR function correctly, HMBOUND
register must be locked otherwise the system just hangs.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Acked-by: Simon Glass <sjg@chromium.org>
Bin Meng [Thu, 10 Sep 2015 06:20:23 +0000 (23:20 -0700)]
x86: galileo: Enable random mac address for Quark
Not like other Intel Ethernet controllers (e.g.: E1000), Intel Quark
SoC integrated designware Ethernet controller does not have a chipset
defined way to store/restore mac address. Enable random mac address
so that we can use Ethernet even without 'ethaddr'.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Acked-by: Simon Glass <sjg@chromium.org>
Bin Meng [Fri, 11 Sep 2015 10:24:37 +0000 (03:24 -0700)]
x86: quark: Add PCIe/USB static register programming after memory init
This adds static register programming for PCIe and USB after memory
init as required by Quark firmware writer guide. Although not doing
this did not cause any malfunction, just do it for safety.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Acked-by: Simon Glass <sjg@chromium.org>
Enabling a PLL while IDDQ is high. The Linux kernel checks for this
condition and warns about it verbosely, so while this seems to work
fine, fix it up according to the programming guidelines provided in
the Tegra K1 TRM (v02p), Section 5.3.8.1 ("PLLC and PLLC4 Startup
Sequence"). The Tegra114 TRM doesn't contain this information, but
the programming of PLLC is the same on Tegra114 and Tegra124.
Signed-off-by: Thierry Reding <treding@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
Enabling a PLL while IDDQ is high. The Linux kernel checks for this
condition and warns about it verbosely, so while this seems to work
fine, fix it up according to the programming guidelines provided in
the Tegra K1 TRM (v02p), Section 5.3.8.1 ("PLLC and PLLC4 Startup
Sequence").
Reported-by: Nicolas Chauvet <kwizart@gmail.com> Signed-off-by: Thierry Reding <treding@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
Thierry Reding [Thu, 20 Aug 2015 09:42:23 +0000 (11:42 +0200)]
p2571: Remove hard-coded counter frequency
The counter frequency is derived from clk_m on Tegra, but that clock can
be configured by the primary bootloader to run at the same frequency as
the oscillator (38.4 MHz on Tegra210) or a divided down frequency (most
typically 19.2 MHz). Remove the hard-coded frequency and allow the timer
setup code to query the correct value at runtime.
Signed-off-by: Thierry Reding <treding@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
Thierry Reding [Thu, 20 Aug 2015 09:42:22 +0000 (11:42 +0200)]
p2371: Remove hard-coded counter frequency
The counter frequency is derived from clk_m on Tegra, but that clock can
be configured by the primary bootloader to run at the same frequency as
the oscillator (38.4 MHz on Tegra210) or a divided down frequency (most
typically 19.2 MHz). Remove the hard-coded frequency and allow the timer
setup code to query the correct value at runtime.
Signed-off-by: Thierry Reding <treding@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
Thierry Reding [Thu, 20 Aug 2015 09:42:21 +0000 (11:42 +0200)]
e2220-1170: Remove hard-coded counter frequency
The counter frequency is derived from clk_m on Tegra, but that clock can
be configured by the primary bootloader to run at the same frequency as
the oscillator (38.4 MHz on Tegra210) or a divided down frequency (most
typically 19.2 MHz). Remove the hard-coded frequency and allow the timer
setup code to query the correct value at runtime.
Signed-off-by: Thierry Reding <treding@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
Thierry Reding [Thu, 20 Aug 2015 09:42:20 +0000 (11:42 +0200)]
ARM: tegra: clk_m is the architected timer source clock
While clk_m and the oscillator run at the same frequencies on Tegra114
and Tegra124, clk_m is the proper source for the architected timer. On
more recent Tegra generations, Tegra210 and later, both the oscillator
and clk_m can run at different frequencies. clk_m will be divided down
from the oscillator.
Signed-off-by: Thierry Reding <treding@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
Thierry Reding [Thu, 20 Aug 2015 09:42:19 +0000 (11:42 +0200)]
ARM: tegra: Implement clk_m
On currently supported SoCs, clk_m always runs at the same frequency as
the oscillator input. However newer SoC generations such as Tegra210 no
longer have that restriction. Prepare for that by separating clk_m from
the oscillator clock and allow SoC code to override the clk_m rate.
Signed-off-by: Thierry Reding <treding@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
Stephen Warren [Thu, 20 Aug 2015 23:38:42 +0000 (17:38 -0600)]
ARM: tegra: replace V_PROMPT define with kconfig
Commit 181bd9dc61d2 "kconfig: add config option for shell prompt" replaced
define V_PROMPT with Kconfig option SYS_PROMPT. This crossed with patches
adding Tegra T210 boards. Migrate the boards to the new scheme.
Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
Stephen Warren [Wed, 19 Aug 2015 23:03:59 +0000 (17:03 -0600)]
ARM: tegra: fix PLLP frequency calc on T210
AFAIK, for all PLLs on all Tegra SoCs, the primary PLL output frequency
is (input * m) / (n * p). However, PLLP's primary output (pllP_out0) on
T210 is the VCO output, and divp is not applied. pllP_out2 does have divp
applied. All other pllP_outN are divided down from pllP_out0. We only
support pllP_out0 in U-Boot at the time of writing.
Fix clock_get_rate() to handle this special case.
This corrects the returned rate for PLLP to be 408MHz rather than 204MHz.
In turn, this causes high enough dividers to be calculated for the various
peripheral clocks that feed off of PLLP. Without this, some peripherals
failed to operate correctly. For instance, one of my SD cards worked
perfectly but an older (presumably slower) card could not be read.
Note that prior to commit 722e000ccd72 "Tegra: PLL: use per-SoC pllinfo
table instead of PLL_DIVM/N/P, etc.", the calculated PLL frequency was
816MHz since the wrong values were being extracted from the PLLP divider
register. This caused overly large peripheral dividers to be calculated,
which while wrong, didn't cause any correctness issues; things simply ran
slower than they could.
Reported-by: Thierry Reding <treding@nvidia.com> Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
Stephen Warren [Wed, 19 Aug 2015 21:15:41 +0000 (15:15 -0600)]
ARM: tegra: fix COUNTER_FREQUENCY for T210
While T210 boards all have 38.4MHz crystals, per the TRM, the only
supported configuration is to divide the crystal frequency by 2 to
generate clk_m, which is what feeds the ARM generic timers amongst other
things. Fix the value of COUNTER_FREQUENCY to reflect this divide-by-2.
When I queried the 19.2 value in Tom's original T210 patches, I wasn't
aware of this extra divide-by-2, and didn't notice any effect from the
incorrect value, since its only used if U-Boot is booted in EL3, whereas
I'm booting it in EL2.
Reported-by: Thierry Reding <treding@nvidia.com> Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
Stephen Warren [Fri, 14 Aug 2015 04:34:22 +0000 (22:34 -0600)]
ARM: tegra: Add p2371-2180 board
P2371-2180 is a P2180 CPU board married to a P2597 I/O board. The
combination contains SoC, DRAM, eMMC, SD card slot, HDMI, USB
micro-B port, Ethernet via USB3, USB3 host port, SATA, PCIe, and
two GPIO expansion headers.
Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
When enabling CONFIG_API and chain-loading GRUB2 on jetson-tk1, only the
eMMC would show up as (hd0), but not the SD card, leading to GRUB not
finding its configuration and modules, falling back to a rescue shell.
This is because enum_ended would get set for !more after returning a
cookie for the first MMC device in group 3.
Fix this by properly setting the "more" argument also in the case of the
first storage device of a group.
Stefan Roese [Mon, 14 Sep 2015 07:17:36 +0000 (09:17 +0200)]
arm: Remove unused ST-Ericsson u8500 arch
This arch does not seem to be supported / used at all in the current
U-Boot mainline source tree any more. So lets remove the core u8500 code
and code that was only referenced by this platform.
Please note that this patch also removes these config options:
As they only seem to be referenced by u8500 based boards. Without any
such board in the current code, these config option don't make sense
any more. Lets remove them as well.
If someone still wants to use this platform, then please send patches
to re-enable support by adding at least one board that references this
code.
Signed-off-by: Stefan Roese <sr@denx.de> Cc: Mathieu Poirier <mathieu.poirier@linaro.org> Cc: John Rigby <john.rigby@linaro.org> Cc: Simon Glass <sjg@chromium.org> Cc: Masahiro Yamada <yamada.masahiro@socionext.com> Cc: Tom Rini <trini@konsulko.com> Cc: Heiko Schocher <hs@denx.de> Cc: Albert Aribaud <albert.u.boot@aribaud.net> Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Stefan Roese [Mon, 14 Sep 2015 06:47:47 +0000 (08:47 +0200)]
mtd: nand: fsmc: Fixes and cleanup for fsmc_nand_switch_ecc()
This patch addresses some comments raised by Scott in the last versions.
Here the changes in detail:
- Removed __maybe_unused as its not needed
- Added check for strength == 4 and error out for the unsupported
ECC strength values
- Don't set .caclulate, .correct, and .bytes for NAND_ECC_SOFT_BCH as this
will be done in nand_scan_tail()
- Set .caclulate back to fsmc_read_hwecc() in the HW case
- Added comment that this function will only be called on SPEAr platforms,
not supporting the BCH8 HW ECC (FSMC_VER8)
Signed-off-by: Stefan Roese <sr@denx.de> Cc: Scott Wood <scottwood@freescale.com> Cc: Tom Rini <trini@konsulko.com> Acked-by: Scott Wood <scottwood@freescale.com>
env: import: hashtable: Prevent buffer overrun when importing environment from file
Lets consider following scenario:
- One uses echo -n "key=value" to define environment variable in a file (single variable)
- The file content is "key=value" without any terminating byte (e.g. 0x0a or
0x0d).
- The file is loaded to u-boot non zero'ed RAM buffer (with load command).
- Then "env import -t -r $loadaddr $filesize" is executed.
- Due to lack of proper termination byte we have classical example of buffer
overrun.
This patch prevents from this by allocating one extra byte than size and
explicitly null terminate it.
There should be no change for normal env import operation after applying
this patch.
Tom Rini [Thu, 3 Sep 2015 18:54:03 +0000 (14:54 -0400)]
ti814x_evm: Switch to SYS_GENERIC_BOARD
Take over maintainership as well. Not tested as PG2.0 (which I have)
needs additional work over PG1.0 (which Matt has).
Cc: Matt Porter <mporter@konsulko.com> Signed-off-by: Tom Rini <trini@konsulko.com> Reviewed-by: Simon Glass <sjg@chromium.org> Tested-by: Simon Glass <sjg@chromium.org>
Stephen Warren [Thu, 6 Aug 2015 21:31:02 +0000 (15:31 -0600)]
fdt: add new fdt address parsing functions
fdtdec_get_addr_size() hard-codes the number of cells used to represent
an address or size in DT. This is incorrect in many cases depending on
the DT binding for a particular node or property (e.g. it is incorrect
for the "reg" property). In most cases, DT parsing code must use the
properties #address-cells and #size-cells to parse addres properties.
This change splits up the implementation of fdtdec_get_addr_size() so
that the core logic can be used for both hard-coded and non-hard-coded
cases. Various wrapper functions are implemented that support cases
where hard-coded cell counts should or should not be used, and where
the client does and doesn't know the parent node ID that contains the
properties #address-cells and #size-cells.
dev_get_addr() is updated to use the new functions.
Core functionality in fdtdec_get_addr_size_fixed() is widely tested via
fdtdec_get_addr_size(). I tested fdtdec_get_addr_size_auto_noparent() and
dev_get_addr() by manually modifying the Tegra I2C driver to invoke them.
Much of the core implementation of fdtdec_get_addr_size_fixed(),
fdtdec_get_addr_size_auto_parent(), and
fdtdec_get_addr_size_auto_noparent() comes from Thierry Reding's
previous commit "fdt: Fix fdtdec_get_addr_size() for 64-bit".
Based-on-work-by: Thierry Reding <treding@nvidia.com> Cc: Thierry Reding <treding@nvidia.com> Cc: Simon Glass <sjg@chromium.org> Cc: Michal Suchanek <hramrach@gmail.com> Signed-off-by: Stephen Warren <swarren@nvidia.com> Acked-by: Simon Glass <sjg@chromium.org>
Dropped #define DEBUG at the top of fdtdec.c: Signed-off-by: Simon Glass <sjg@chromium.org>
Simon Guinot [Thu, 3 Sep 2015 09:12:20 +0000 (11:12 +0200)]
ARM: Kirkwood: fix IDE configuration on LaCie boards
On the LaCie boards netspace_max_v2 and net2big_v2, two internal hard
drives are available. Additionally on the d2net_v2 board, an extra hard
drive can be plugged via eSATA.
This patch updates CONFIG_SYS_IDE_MAXBUS and CONFIG_SYS_IDE_MAXDEVICE
accordingly for this boards.
Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
mx6ul_14x14_evk: Use the default CONFIG_SYS_PBSIZE
Entering the maximum number of characters defined by CONFIG_SYS_CBSIZE into
the console and hitting enter afterwards, causes a hang in the system because
CONFIG_SYS_PBSIZE is not capable of storing the extra characters of the error
message:
"Unknown command '' - try 'help'".
Use the default CONFIG_SYS_PBSIZE definition from config_fallbacks.h to solve
this problem.
arm: mx6: cm-fx6: modify device tree for old revisions of utilite
Old revisions of Utilite (a miniature PC based on cm-fx6) do not have
a card detect for mmc, and thus the kernel needs to be told that
there's a persistent storage on usdhc3 to force it to probe the mmc
card.
Check the baseboard revision and modify the device tree accordingly
if needed.
compulab: eeprom: propagate error value in read_mac_addr()
cl_eeprom_read_mac_addr() doesn't differentiate between success case and
inability to access eeprom. Fix this by propagating the return value of
cl_eeprom_setup().
Cc: Stefano Babic <sbabic@denx.de> Cc: Igor Grinberg <grinberg@compulab.co.il> Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il> Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Peng Fan [Sun, 6 Sep 2015 07:02:34 +0000 (15:02 +0800)]
imx: mx6ul: support mx6ul 9x9 evk board
This patch is to support mx6ul_9x9_evk board based on mx6ul_14x14_evk,
the difference between mx6ul 9x9 evk and mx6ul 14x14 evk are:
1. mx6ul 9x9 evk use pfuze3000, while mx6ul 14x14 evk use DCDC.
2. mx6ul 9x9 evk supports 256MB LPDDR2, while mx6ul 14x14 evk
supports 512MB DDR3
3. mx6ul_9x9_evk use 9x9 package, while mx6ul_14x14_evk use 14x14 package.
This patch add the following:
1. Discard PHYS_SDRAM_SIZE from header file, use imx_ddr_size()
2. Introduce a macro is_mx6ul_9x9_evk using
CONFIG_IS_ENABLED(TARGET_MX6UL_9X9_EVK) to avoid "#ifdef xxx" in non-SPL
part. To SPL part, CONFIG_IS_ENABLED(TARGET_MX6UL_9X9_EVK) can not work,
so still use "#ifdef CONFIG_TARGET_MX6UL_9X9_EVK" to differentiate with
mx6ul_14x14_evk. And we have no way to dymaically checking this chip
is 9x9 or 14x14.
3. mx6ul_9x9_evk use pfuze3000, so enabled POWER related configurations.
POWER related configurations also effect for mx6ul_14x14_evk. But
power_init_board implementation using 'if (is_mx6ul_9x9_evk())' to
do initialization for mx6ul_9x9_evk, and do nothing for mx6ul_14x14_evk.
4. mx6ul_9x9_evk use lpddr2 with size 256MB, so add related SPL DRAM
configurations.
5. Enable CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG and setting dtb file
according to board_rev and board_name.
6. Add TARGET_MX6UL_9X9_EVK Kconfig entry
CPU: Freescale i.MX6UL rev1.0 792 MHz (running at 396 MHz)
CPU: Commercial temperature grade (0C to 95C) at 41C
Reset cause: POR
Board: MX6UL 9x9 EVK
I2C: ready
DRAM: 256 MiB
PMIC: PFUZE3000 DEV_ID=0x30 REV_ID=0x11
MMC: FSL_SDHC: 0, FSL_SDHC: 1
In: serial
Out: serial
Err: serial
Net: FEC1
Hit any key to stop autoboot: 0
Signed-off-by: Peng Fan <Peng.Fan@freescale.com> Cc: Stefano Babic <sbabic@denx.de>
Running mxsboot on a big-endian system produces a sd image which
cannot be started by the i.MX28 ROM. It complains on the debug
uart as following:
0x8020a009
0x80502008
0x8020a009
0x80502008
...
Enforcing all fields within the BCB to little-endian make
the image bootable again.
Signed-off-by: Michael Heimpold <mhei@heimpold.de> Acked-by: Stefano Babic <sbabic@denx.de> Acked-by: Marek Vasut <marex@denx.de>
Adrian Alonso [Thu, 3 Sep 2015 16:49:28 +0000 (11:49 -0500)]
imx: mx7dsabresd: Add support for MX7D SABRESD board
* Add i.MX7D SABRESD target board support with enabled modules:
UART, PMIC, USB/OTG, SD, eMMC, ENET, I2C, 74LV IOX.
Build target: mx7dsabresd_config
Signed-off-by: Peng Fan <Peng.Fan@freescale.com> Signed-off-by: Fugang Duan <B38611@freescale.com> Signed-off-by: Ye.Li <B37916@freescale.com> Signed-off-by: Adrian Alonso <aalonso@freescale.com>
Adrian Alonso [Wed, 2 Sep 2015 18:54:18 +0000 (13:54 -0500)]
imx: imx7d: clock control module support
* Add Clock control module (CCM) support
* iMX7D SoC introduces 3 main clock sysmtem abstraction for clock
root frequency generation denominated clock slices.
Core clock slice: hihg speed clock for ARM core
Bus clock slice: for bus clocks
IP clock slice: Peripheral clocks
* At system boot ROM enables PLL_ARM, PLL_DDR, PLL_SYS, PLL_ENET
In u-boot, we have to:
- Configure PFD3- PFD7 for freq we needed in u-boot
- Set clock root for peripherals (ip channel)
Signed-off-by: Adrian Alonso <aalonso@freescale.com> Signed-off-by: Peng Fan <Peng.Fan@freescale.com> Signed-off-by: Ye.Li <B37916@freescale.com>
Adrian Alonso [Wed, 2 Sep 2015 18:54:16 +0000 (13:54 -0500)]
imx: system counter driver for imx7d and mx6ul
Add system counter driver for imx7d and mx6ul
imx7 and imx6ul supports system counter timer as well as
GPT timer (arch/arm/imx-common/timer.c); The default for
imx7 is systemcounter timer.
Signed-off-by: Ye.Li <B37916@freescale.com> Signed-off-by: Adrian Alonso <aalonso@freescale.com>
Stephen Warren [Fri, 11 Sep 2015 23:10:02 +0000 (17:10 -0600)]
usb: ci_udc: fix emissions of ZLPs
Commit 6a132416359e "ci_udc: Update the ci_udc driver to support bulk
transfers" caused the value of "len" to change without updating subsquent
users of that variable in ci_ep_submit_next_request(). This caused the
code that detects when to emit ZLPs (Zero Length Packets) never to
trigger, which in turn caused host timeouts when a ZLP was required,
which in turn broke tests/dfu/, even despite the assertion in that
commit's description that "These changes are tested for both the DFU and
lthor."
Fix this by modifying the added dtd iteration code not to modify "len",
but rather to keep state in a separate variable. Rename the variables
while we're at it so they describe their purpose better.
Fixes: 6a132416359e ("ci_udc: Update the ci_udc driver to support bulk transfers") Cc: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com> Signed-off-by: Stephen Warren <swarren@nvidia.com>
Without this function, uboot will hang when executing fastboot comamnd.
See following flow:
"fastboot_tx_write_str->fastboot_tx_write->usb_ep_dequeue->ep->ops->dequeue"
without implement ci_udc dequeue function, ep->ops->dequeue is NULL, then
uboot will hang.
Tested on mx6qsabresd board with fastboot enabled.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com> Tested-by: Fabio Estevam <fabio.estevam@freescale.com> Cc: "Łukasz Majewski" <l.majewski@samsung.com> Cc: Marek Vasut <marex@denx.de>
The current simplify lpc32xx gpio driver implementation assume a
maximum of 32 GPIO per port; there are a total of 22 GPI, 24 GPO
and 6 GPIO to managed on port 3.
Update the driver to fix the following:
1) When requesting GPI_xx and GPO_xx on port 3 (xx is the same number)
the second call to "gpio_request" will return -EBUSY.
2) The status of GPO_xx pin report the status of the
corresponding GPI_xx pin when using the "gpio status" command.
3) The gpio driver may setup the direction register for the wrong
gpio when calling "gpio_direction_input" (GPI_xx) or
"gpio_direction_output" (GPO_xx) on port 3; the call to the
direction is require to use the "gpio status" command.
The following change were done in the driver:
1) port3 GPI are cache in a separate 32 bits in the array.
2) port3 direction register written only for GPIO pins.
3) port3 GPO & GPIO (as output) are read using "p3_outp_state".
4) LPC32XX_GPI_P3_GRP updated to match the change.
introduce BIT() definition, used in at91_udc gadget
driver.
Signed-off-by: Heiko Schocher <hs@denx.de>
[remove all other occurrences of BIT(x) definition] Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com> Acked-by: Stefan Roese <sr@denx.de> Acked-by: Anatolij Gustschin <agust@denx.de>
igep00x0: Switch to use the generic distro configuration and environment.
This patch changes a little bit the environment, current environment was broken
for a long time, and board don't as expected sometimes, on production systems
this is fixed adding boot script. I think it's time to change this to make a
system conformant environment and use generic distro configurations and
environment instead. We can use a boot script for the old way boot mode.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
projects / u-boot.git / log