Egli, Samuel [Fri, 13 Feb 2015 14:47:10 +0000 (15:47 +0100)]
mtd, omap: fix case NAND_OMAP_GPMC_PREFETCH not defined
The patch c316f577b4b72d1a1aeb559e9b3fad20808f1ffd breaks
siemens boards because prefetch mode is not enabled.
I assume it breaks other boards as well that don't use
prefetch.
This patch sets read_buf to nand_read_buf if
NAND_OMAP_GPMC_PREFETCH is not defined.
Signed-off-by: Samuel Egli <samuel.egli@siemens.com> CC: Daniel Mack <zonque@gmail.com> CC: Guido MartÃnez <guido@vanguardiasur.com.ar> CC: Tom Rini <trini@ti.com> CC: Heiko Schocher <hs@denx.de>
Michael Walle [Fri, 13 Feb 2015 17:45:57 +0000 (18:45 +0100)]
lsxl: add a README file
The README describes the recovery method which can be used if the NAS box
is not reachable anymore. Addionally, it describes the different boot
scripts.
Simon Glass [Wed, 11 Feb 2015 01:52:35 +0000 (18:52 -0700)]
sandbox: Adjust the order of the NO_SDL check
An option is provided to avoid using SDL in U-Boot sandbox (and drop
support for the LCD). However the check in the Makefile is too late
and warnings are printed even if NO_SDL=y is given.
Adjust the order to avoid this warning.
Signed-off-by: Simon Glass <sjg@chromium.org> Acked-by: Jeroen Hofstee <jeroen@myspectrum.nl>
Joe Hershberger [Fri, 6 Feb 2015 21:37:31 +0000 (15:37 -0600)]
sandbox: Return '-c command' exit value as sandbox exit code
When a command is passed into sandbox using the '-c' argument the
command is run directly. This is most helpful when running tests (such
as test-dm.sh). Previously the exit code was an unused enum. Change it
to be the actual return code from the command so that the script calling
sandbox can know if the command succeeded (tests passed). Also remove
the now completely unused "exit_state" in sandbox.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com> Acked-by: Simon Glass <sjg@chromium.org>
Albert ARIBAUD [Sat, 31 Jan 2015 23:12:44 +0000 (00:12 +0100)]
buildman: allow multiple toolchains in a single path
When buildman scans a toolchain path, it stops at the
first toolchain found. However, a single path can contains
several toolchains, each with its own prefix.
This patch lets buildman scan all toolchains in the path.
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net> Acked-by: Simon Glass <sjg@chromium.org>
Akshay Saraswat [Wed, 4 Feb 2015 10:30:05 +0000 (16:00 +0530)]
Exynos: Clock: Cleanup soc_get_periph_rate
Since we have src, div and pre-div mask bits defined corresponding
to peripherals, calculation of clock specific to I2C appears
redundant and confusing. Using clk_bit_info struct we can write
calculations generic to all peripherals which makes code easy to
understand and free from peripheral specific exceptions.
Signed-off-by: Akshay Saraswat <akshay.s@samsung.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Akshay Saraswat [Wed, 4 Feb 2015 10:30:04 +0000 (16:00 +0530)]
Exynos: clock: change mask bits as per peripheral
We have assumed and kept mask bits for divider and pre-divider
as 0xf and 0xff, respectively. But these mask bits change from
one peripheral to another, and hence, need to be specified in
accordance with the peripherals.
Signed-off-by: Akshay Saraswat <akshay.s@samsung.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Akshay Saraswat [Wed, 4 Feb 2015 10:30:03 +0000 (16:00 +0530)]
Exynos5: Use clock_get_periph_rate generic API
Replacing SoC and peripheral specific function calls with generic
clock_get_periph_rate calls to get the peripheral clocks.
Also, removing dead code of peripheral and SoC specific function
implementations which was used earlier for fetching peripheral clocks.
This code is not being used anymore because of the introduction
of generic clock_get_periph_rate function.
Signed-off-by: Akshay Saraswat <akshay.s@samsung.com> Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Akshay Saraswat [Wed, 4 Feb 2015 10:30:02 +0000 (16:00 +0530)]
Exynos5: Fix exynos5_get_periph_rate calculations
exynos5_get_periph_rate function reads incorrect div for
SDMMC2 & 3. It also reads prediv and does division only for
SDMMC0 & 2 when actually various other peripherals need that.
Adding changes to fix these mistakes in periph rate calculation.
Signed-off-by: Akshay Saraswat <akshay.s@samsung.com> Reviewed-by: Simon Glass <sjg@chromium.org> Tested-by: Simon Glass <sjg@chromium.org> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Akshay Saraswat [Wed, 4 Feb 2015 10:30:01 +0000 (16:00 +0530)]
Exynos542x: Add and enable get_periph_rate support
We planned to fetch peripheral rate through one generic API per
peripheral. These generic peripheral functions are in turn
expected to fetch apt values from a function refactored as
per SoC versions. This patch adds support for fetching peripheral
rates for Exynos5420 and Exynos5800.
Signed-off-by: Akshay Saraswat <akshay.s@samsung.com> Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Akshay Saraswat [Wed, 4 Feb 2015 10:30:00 +0000 (16:00 +0530)]
Exynos542x: Move exynos5420_get_pll_clk up and rename
Moving exynos5420_get_pll_clk function definition up in the
code to keep it together with rest of SoC_get_pll_clk functions.
This makes code more legible and also removes the need of
declaration when called before the position of definition in
code. Also, renaming exynos5420_get_pll_clk to
exynos542x_get_pll_clk because it is being used for both Exynos
5420 and 5800.
Signed-off-by: Akshay Saraswat <akshay.s@samsung.com> Reviewed-by: Simon Glass <sjg@chromium.org> Tested-by: Simon Glass <sjg@chromium.org> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Akshay Saraswat [Wed, 4 Feb 2015 10:29:59 +0000 (15:59 +0530)]
Exynos5: Fix compiler warnings due to clock_get_periph_rate
Apparently, members of clk_bit_info array do not map correctly
to the members of enum periph_id. This mapping got broken after
we changed periph_id(s) to reflect interrupt number instead of
their position in a sequence. This patch intends to fix above
mentioned issue.
Signed-off-by: Akshay Saraswat <akshay.s@samsung.com> Reviewed-by: Simon Glass <sjg@chromium.org> Tested-by: Simon Glass <sjg@chromium.org> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Alexey Brodkin [Tue, 13 Jan 2015 15:35:46 +0000 (18:35 +0300)]
arc: introduce U-Boot port for ARCv2 ISA
ARC HS and ARC EM are new cores based on ARCv2 ISA which is binary
incompatible with ISAv1 (AKA ARCompact).
Significant difference between ISAv2 and v1 is implementation of
interrupt vector table.
In v1 it is implemented in the same way as on many other architectures -
as a special location where user may put whether code executed in place
(if machine word of space is enough) or jump to a full-scale interrupt
handler.
In v2 interrupt table is just an array of adresses of real interrupt
handlers. That requires a separate section for IVT that is not encoded
as code by assembler.
This change adds support for following cores:
* ARC EM6 (simple 32-bit microcontroller without MMU)
* ARC HS36 (advanced 32-bit microcontroller without MMU)
* ARC HS38 (advanced 32-bit microcontroller with MMU)
As a part of ARC HS38 new version of MMU (v4) was introduced.
Also this change adds AXS131 board which is the same DW ARC SDP base board but
with ARC HS38 CPU tile.
Michal Simek [Mon, 2 Feb 2015 15:31:59 +0000 (16:31 +0100)]
dm: Add support for all targets which requires MANUAL_RELOC
Targets with CONFIG_NEEDS_MANUAL_RELOC do not use REL/RELA
relocation (mostly only GOT) where functions aray are not
updated. This patch is fixing function pointers for DM core
and serial-uclass to ensure that relocated functions are called.
Signed-off-by: Michal Simek <michal.simek@xilinx.com> Acked-by: Simon Glass <sjg@chromium.org>
Peng Fan [Tue, 10 Feb 2015 06:46:34 +0000 (14:46 +0800)]
dm:gpio:mxc add DT support
This patch add DT support for mxc gpio driver.
There are one place using CONFIG_OF_CONTROL macro.
1. The U_BOOT_DEVICES and mxc_plat array are complied out. To DT,
platdata is alloced using calloc, so there is no need to use mxc_plat.
The following situations are tested, and all work fine:
1. with DM, without DT
2. with DM and DT
3. without DM
Since device tree has not been upstreamed, if want to test this patch.
The followings need to be done.
+ pieces of code does not gpio_request when using gpio_direction_xxx and
etc, need to request gpio.
+ move the gpio settings from board_early_init_f to board_init
+ define CONFIG_DM ,CONFIG_DM_GPIO and CONFIG_OF_CONTROL
+ Add device tree file and do related configuration in
`make ARCH=arm menuconfig`
These will be done in future patches by step.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com> Acked-by: Igor Grinberg <grinberg@compulab.co.il> Acked-by: Simon Glass <sjg@chromium.org>
Peng Fan [Tue, 10 Feb 2015 06:46:33 +0000 (14:46 +0800)]
dm:gpio:mxc add a bank_index entry in platdata
Add a new entry in platdata structure and intialize
bank_index in mxc_plat array.
This new entry can avoid using `plat - mxc_plat` by using
`plat->bank_index`.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com> Acked-by: Igor Grinberg <grinberg@compulab.co.il> Acked-by: Simon Glass <sjg@chromium.org>
Simon Glass [Fri, 6 Feb 2015 04:41:33 +0000 (21:41 -0700)]
dm: i2c: Make API accessible even without CONFIG_DM
Make the driver model I2C API available always, even if driver model
is not enabled. This allows for a 'soft' switch-over, where drivers can
use the new structures in code which is compiled but not yet used. This
makes migration easier in some cases.
Fix up the existing drivers which define their own 'struct i2c_msg'.
Signed-off-by: Simon Glass <sjg@chromium.org> Acked-by: Heiko Schocher <hs@denx.de>
Stefan Roese [Sat, 7 Feb 2015 18:51:52 +0000 (11:51 -0700)]
powerpc: ppc4xx: Enable CONFIG_DISPLAY_BOARDINFO
This also displays the "Board:" line in the bootup text with the
generic board support code.
Signed-off-by: Stefan Roese <sr@denx.de> Cc: Simon Glass <sjg@chromium.org> Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Simon Glass <sjg@chromium.org>
Stefan Roese [Sat, 7 Feb 2015 18:51:51 +0000 (11:51 -0700)]
powerpc: ppc4xx: Add defaults for DT based booting to really work
These additional nodes need to be provided to get U-Boot to boot correctly
on the Canyonlands / Glacier board:
- chosen path to the console-uart
- reg-shift set to 0 in the uart device nodes
Signed-off-by: Stefan Roese <sr@denx.de> Cc: Simon Glass <sjg@chromium.org> Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Simon Glass <sjg@chromium.org>
Stefan Roese [Sat, 7 Feb 2015 18:51:50 +0000 (11:51 -0700)]
powerpc: ppc4xx: Change from OF_SEPARATE to OF_EMBED
This is necessary, as ppc4xx has the reset vector located at the end
of the U-Boot image. This needs to be flashed to the end of the NOR
flash. Adding the dtb to the main U-Boot image will break booting
on ppc4xx. This patch now embeds the dtb in the U-Boot image instead.
Signed-off-by: Stefan Roese <sr@denx.de> Cc: Simon Glass <sjg@chromium.org> Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Simon Glass <sjg@chromium.org>
Simon Glass [Sat, 7 Feb 2015 18:51:44 +0000 (11:51 -0700)]
powerpc: ppc4xx: Allow the end of u-boot.bin to be found
Define an _end symbol indicating the end of u-boot.bin. Also add some dummy
words into the link script to ensure that u-boot.bin will always extend
that far. There may be a better way of doing this.
Simon Glass [Sat, 7 Feb 2015 18:51:36 +0000 (11:51 -0700)]
powerpc: ppc4xx: canyonlands: config: Tidy up CONFIGs and config.mk
Many CONFIG options have an unnecessary value of 1. CONFIG_440 is set in
the various board config files. Also simplify the CONFIG_440 check in
config.mk
Simon Glass [Sat, 7 Feb 2015 18:51:34 +0000 (11:51 -0700)]
Introduce board_init_f_mem() to handle early memory layout
At present on some architectures we set up the following before calling
board_init_f():
- global_data
- stack
- early malloc memory
Adding the code to support early malloc and global data setup to every
arch's assembler start-up is a pain. Also this code is not actually
architecture-specific. We can use common code for all architectures and
with a bit of care we can write this code in C.
Add a new function to deal with this. It should be called after memory
is available, with a pointer to the top of the area that should be used
before relocation. The function will set things up and return the lowest
memory address that it allocated/used. That can then be set as the top
of the stack.
Note that on some archs this function will use the stack, so the stack
pointer should be set to same value as is pased to board_init_f_mem().
A margin of 128 bytes will be left for this stack, so that it is not
overwritten. This means that 64 bytes is wasted by this early call.
This is not strictly necessary on several more modern archs, so we could
remove this at the cost of some arch-dependent code.
With this function there is no-longer any need for the assembler code to
zero global_data or set up the early malloc pointers.
Hans de Goede [Wed, 4 Feb 2015 12:05:50 +0000 (13:05 +0100)]
malloc_simple: Return NULL on malloc failure rather then calling panic()
All callers of malloc should already do error checking, and may even be able
to continue without the alloc succeeding.
Moreover, common/malloc_simple.c is the only user of .rodata.str1.1 in
common/built-in.o when building the SPL, triggering this gcc bug:
https://gcc.gnu.org/bugzilla/show_bug.cgi?id=54303
Causing .rodata to grow with e.g. 0xc21 bytes, nullifying all benefits of
using malloc_simple in the first place.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Simon Glass <sjg@chromium.org>
If no device is connected to I2C bus, the i2c probe command
can take a lot of time for probe each address. This commit
reduces the busy timeout to 10ms for standard and high speed
modes. This doesn't break the transmission an also allow for
properly probe the devices.
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Changes v3:
- new commit, after split the next one Tested-by: Simon Glass <sjg@chromium.org>
Michael Walle [Sun, 8 Feb 2015 19:06:07 +0000 (20:06 +0100)]
lsxl: switch from bootm to bootz for boot commands
Use the bootz command to load zImages in case of any new boot scripts. Only
the legacy one will still use bootm. Apart form the fact, that this will
simplify the image generation process, it saves one copy of the kernel
image: Common practice is to generate an uImage with a loading address of
0x8000. This uImage contains a compressed zImage, which will unpack the
kernel image to the beginning of the RAM. But because there is already the
compressed image the uncompressor first relocates the compressed image to a
higher location. The load address is encoded into the uImage which is
generated by the distributions and thus cannot be easily changed. By using
the bootz command we can load the compressed image to a higher memory
address and the decompressor doesn't have to reloacte the image.
Michael Walle [Sun, 8 Feb 2015 19:06:06 +0000 (20:06 +0100)]
lsxl: place the dtb below the inital ramdisk
The dtb was loaded at a memory address after the initial ramdisk. Thus a
large ramdisk would overwrite the dtb. Move it to "ramdisk_start - 64k".
64k should be enough for the device tree blob. Also the kernel
documentation arm/Booting suggests to put the dtb before the initial
ramdisk.
Michael Walle [Sun, 8 Feb 2015 19:06:05 +0000 (20:06 +0100)]
lsxl: use default load addresses for legacy boot
The load addresses for the bootcmd_legacy script were taken from the
original bootloader from Buffalo. But newer kernels are too big and the
uncompressing will overwrite parts of the initial ramdisk. Therefore,
we switch to the load addresses which are also used by the other boot
script.
Nikita Kiryanov [Tue, 3 Feb 2015 11:32:32 +0000 (13:32 +0200)]
lcd: split splash code into its own function
lcd_logo() currently performs tasks well beyond just displaying the logo.
It has code which displays splash image, it has logic which determines
when the different display features are displayed, and it is coupled with
the lcd console because it holds the responsibility of returning the
lcd console base address.
Make lcd_logo() just about the logo by:
* Moving splash image display code into a dedicated function
* Moving the logic regarding when various features are displayed to
lcd_clear() (which is arguably not the correct name for housing such
code either, but it is currently the most fitting location code wise)
* Move the responsibility of setting the console base address to
lcd_clear() too.
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il> Reviewed-by: Simon Glass <sjg@chromium.org> Tested-by: Bo Shen <voice.shen@atmel.com> Tested-by: Josh Wu <josh.wu@atmel.com> Cc: Bo Shen <voice.shen@atmel.com> Cc: Simon Glass <sjg@chromium.org> Cc: Anatolij Gustschin <agust@denx.de>
Nikita Kiryanov [Tue, 3 Feb 2015 11:32:31 +0000 (13:32 +0200)]
lcd: dt: extract simplefb support
We now have api functions that can support compiling simplefb code as its own
module. Since this code is not part of the display functionality, extract it
to its own file.
Raspberry Pi is updated to accommodate the changes.
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il> Acked-by: Stephen Warren <swarren@wwwdotorg.org> Reviewed-by: Simon Glass <sjg@chromium.org> Tested-by: Bo Shen <voice.shen@atmel.com> Tested-by: Josh Wu <josh.wu@atmel.com> Cc: Simon Glass <sjg@chromium.org> Cc: Anatolij Gustschin <agust@denx.de> Cc: Stephen Warren <swarren@wwwdotorg.org>
Nikita Kiryanov [Tue, 3 Feb 2015 11:32:30 +0000 (13:32 +0200)]
lcd: rename bitmap_plot to better represent its functionality
The name "bitmap_plot" is misleading because it implies that this is a generic
function capable of dealing with any bitmap, but its implementation only works
with the logo data.
Rename the function to better reflect this.
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il> Reviewed-by: Simon Glass <sjg@chromium.org> Tested-by: Bo Shen <voice.shen@atmel.com> Tested-by: Josh Wu <josh.wu@atmel.com> Cc: Simon Glass <sjg@chromium.org> Cc: Anatolij Gustschin <agust@denx.de>
Nikita Kiryanov [Tue, 3 Feb 2015 11:32:27 +0000 (13:32 +0200)]
lcd: introduce lcd_set_cmap
Reduce the lcd_display_bitmap #ifdef complexity by extracting Atmel-specific
code for setting cmap for bitmap images into a new function lcd_set_cmap().
A default version is implemented with the remainder of the code.
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il> Reviewed-by: Simon Glass <sjg@chromium.org> Tested-by: Bo Shen <voice.shen@atmel.com> Tested-by: Josh Wu <josh.wu@atmel.com> Cc: Bo Shen <voice.shen@atmel.com> Cc: Simon Glass <sjg@chromium.org> Cc: Anatolij Gustschin <agust@denx.de>
Nikita Kiryanov [Tue, 3 Feb 2015 11:32:25 +0000 (13:32 +0200)]
lcd: mpc823: move mpc823-specific lcd_logo_set_cmap code to mpc8xx_lcd.c
Reduce the bitmap_plot #ifdef complexity by extracting MPC823-specific code for
setting cmap into its own implementation of lcd_logo_set_cmap(), implemented in
mpc8xx_lcd.c. In the MPC823 implementation, ARRAY_SIZE(bmp_logo_palette) is
switched for BMP_LOGO_COLORS to avoid having to include bmp_logo_data.h, which
would cause a compilation error because the logo data and palette arrays would
be defined twice.
This is a step towards cleaning bitmap_plot() of platform-specific code.
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il> Reviewed-by: Simon Glass <sjg@chromium.org> Tested-by: Bo Shen <voice.shen@atmel.com> Tested-by: Josh Wu <josh.wu@atmel.com> Cc: Simon Glass <sjg@chromium.org> Cc: Anatolij Gustschin <agust@denx.de>
projects / u-boot.git / log