Tom Rini [Fri, 31 Jan 2020 18:26:28 +0000 (13:26 -0500)]
Merge tag 'uniphier-v2020.04-2' of https://gitlab.denx.de/u-boot/custodians/u-boot-uniphier
UniPhier SoC updates for v2020.04 (2nd)
Denali NAND driver changes:
- Set up more registers in denali-spl for SOCFPGA
- Make clocks optional
- Do not assert reset signals in the remove hook
- associate SPARE_AREA_SKIP_BYTES with DT compatible
- switch to UCLASS_MTD
UniPhier platform changes:
- fix a bug in dram_init()
- specify loadaddr for "source" command
Masahiro Yamada [Wed, 29 Jan 2020 15:55:54 +0000 (00:55 +0900)]
mtd: rawnand: denali_dt: insert udelay() after reset deassert
When the reset signal is de-asserted, the HW-controlled bootstrap
starts running unless it is disabled in the SoC integration.
It issues some commands to detect a NAND chip, and sets up registers
automatically. Until this process finishes, software should avoid
any register access.
Without this delay function, some of UniPhier boards hangs up while
executing nand_scan_ident(). (denali_read_byte() is blocked)
Marek Vasut [Tue, 21 Jan 2020 19:03:11 +0000 (20:03 +0100)]
mtd: rawnand: denali: Do not reset the block before booting the kernel
The Denali NAND driver in mainline Linux currently cannot deassert the
reset. The upcoming Linux 5.6 will support the reset controlling, and
also set up SPARE_AREA_SKIP_BYTES correctly. So, the Denali driver in
the future kernel will work without relying on any bootloader or firmware.
However, we still need to take care of stable kernel versions for a while.
U-boot should not assert the reset of this controller.
Masahiro Yamada [Tue, 21 Jan 2020 19:03:10 +0000 (20:03 +0100)]
mtd: rawnand: denali_dt: make the core clock optional
The "nand_x" and "ecc" clocks are currently optional. Make the core
clock optional in the same way. This will allow platforms with no clock
driver support to use this driver.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Tested-by: Marek Vasut <marex@denx.de> # On SoCFPGA Arria V
Marek Vasut [Tue, 21 Jan 2020 19:03:09 +0000 (20:03 +0100)]
mtd: rawnand: denali-spl: Add missing hardware init on SoCFPGA
On Altera SoCFPGA, upon either cold-boot or power-on reset, the
Denali NAND IP is initialized by the BootROM ; upon warm-reset,
the Denali NAND IP is NOT initialized by BootROM. In fact, upon
warm-reset, the SoCFPGA BootROM checks whether the SPL image in
on-chip RAM is valid and if so, completely skips re-loading the
SPL from the boot media.
This does sometimes lead to problems where the software left
the boot media in inconsistent state before warm-reset, and
because the BootROM does not reset the boot media, the boot
media is left in this inconsistent state, often until another
component attempts to access the boot media and fails with an
difficult to debug failure. To mitigate this problem, the SPL
on Altera SoCFPGA always resets all the IPs on the SoC early
on boot.
This results in a couple of register values, pre-programmed by
the BootROM, to be lost during this reset. To restore correct
operation of the IP on SoCFPGA, these values must be programmed
back into the controller by the driver. Note that on other SoCs
which do not use the HW-controlled bootstrap, more registers
may have to be programmed.
This also aligns the SPL behavior with the full Denali NAND
driver, which sets these values in denali_hw_init().
Signed-off-by: Marek Vasut <marex@denx.de> Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Fabio Estevam [Wed, 29 Jan 2020 20:05:29 +0000 (17:05 -0300)]
Makefile: Fix the location of the migration file
Since commit e1910d93b890 ("doc: driver-model: Convert MIGRATION.txt to
reST") MIGRATION.txt has been converted to migration.rst, so update
the Makefile references accordingly.
Fixes: e1910d93b890 ("doc: driver-model: Convert MIGRATION.txt to reST") Signed-off-by: Fabio Estevam <festevam@gmail.com> Reviewed-by: Tom Rini <trini@konsulko.com>
In upstream libfdt, 6dcb8ba4 "libfdt: Add helpers for accessing
unaligned words" introduced changes to support unaligned reads for ARM
platforms and 11738cf01f15 "libfdt: Don't use memcpy to handle unaligned
reads on ARM" improved the performance of these helpers.
In practice however, this only occurs when the user has forced the
device tree to be placed in memory in a non-aligned way, which in turn
violates both our rules and the Linux Kernel rules for how things must
reside in memory to function.
This "in practice" part is important as handling these other cases adds
visible (1 second or more) delay to boot in what would be considered the
fast path of the code.
Cc: Patrice CHOTARD <patrice.chotard@st.com> Cc: Patrick DELAUNAY <patrick.delaunay@st.com> Link: https://www.spinics.net/lists/devicetree-compiler/msg02972.html Signed-off-by: Tom Rini <trini@konsulko.com> Tested-by: Patrice Chotard <patrice.chotard@st.com>
Coreutils command nproc can be used on Linux and BSD to count the number of
available CPU cores. Use this instead of relying on the parsing of the
Linux specific proc file system.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Tom Rini [Tue, 21 Jan 2020 16:53:38 +0000 (11:53 -0500)]
cmd/gpt: Address error cases during gpt rename more correctly
New analysis by the tool has shown that we have some cases where we
weren't handling the error exit condition correctly. When we ran into
the ENOMEM case we wouldn't exit the function and thus incorrect things
could happen. Rework the unwinding such that we don't need a helper
function now and free what we may have allocated.
Fixes: 18030d04d25d ("GPT: fix memory leaks identified by Coverity") Reported-by: Coverity (CID: 275475, 275476) Cc: Alison Chaiken <alison@she-devel.com> Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com> Cc: Jordy <jordy@simplyhacker.com> Signed-off-by: Tom Rini <trini@konsulko.com> Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Tom Rini [Wed, 29 Jan 2020 14:34:13 +0000 (09:34 -0500)]
Merge tag 'for-v2020.04' of https://gitlab.denx.de/u-boot/custodians/u-boot-i2c
i2c changes for 2020.04
- updates the Designware I2C driver
- get timings from device tree
- handle units in nanoseconds
- make sure that the requested bus speed is not exceeded
- few smaller clean-ups
- adds enums for i2c speed and update drivers which use them
- global_data: remove unused mxc_i2c specific field
Martin Fuzzey [Tue, 14 Jan 2020 15:56:18 +0000 (15:56 +0000)]
pmic: allow dump command for non contiguous register maps
Some PMICs (such as the DA9063) have non-contiguous register maps.
Attempting to read the non implemented registers returns an error
rather than a dummy value which causes 'pmic dump' to terminate
prematurely.
Fix this by allowing the PMIC driver to return -ENODATA for such
registers, which will then be displayed as '--' by pmic dump.
Use a single error code rather than any error code so that
we can distinguish between a hardware failure reading the PMIC
and a non implemented register known to the driver.
Signed-off-by: Martin Fuzzey <martin.fuzzey@flowbird.group>
Martin Fuzzey [Tue, 14 Jan 2020 15:56:17 +0000 (15:56 +0000)]
power: regulator: add driver for Dialog DA9063 PMIC
Add a driver for the regulators in the the DA9063 PMIC.
Robert Beckett: move regulator modes to header so board code can set
modes. Correct mode mask used in ldo_set_mode.
Add an option CONFIG_SPL_DM_REGULATOR_DA9063.
Signed-off-by: Martin Fuzzey <martin.fuzzey@flowbird.group> Signed-off-by: Robert Beckett <bob.beckett@collabora.com>
Martin Fuzzey [Tue, 14 Jan 2020 15:56:16 +0000 (15:56 +0000)]
power: pmic: add driver for Dialog DA9063 PMIC
This adds the basic register access operations and child regulator
binding (if a regulator driver exists).
Robert Beckett: simplify accesses by using bottom bit of address as
offset overflow. This avoids the need to track which page we are on.
Add an option CONFIG_SPL_DM_PMIC_DA9063.
Signed-off-by: Martin Fuzzey <martin.fuzzey@flowbird.group> Signed-off-by: Robert Beckett <bob.beckett@collabora.com>
Ian Ray [Tue, 14 Jan 2020 16:18:20 +0000 (16:18 +0000)]
rtc: s35392a: encode command correctly
The 3-bit "command", or register, is encoded within the device address.
Configure the device accordingly, and pass command in DM I2C read/write
calls correctly.
Signed-off-by: Ian Ray <ian.ray@ge.com> Signed-off-by: Robert Beckett <bob.beckett@collabora.com>
This can be used for device tree size reduction similar as
CONFIG_OF_SPL_REMOVE_PROPS option. Some boards must pass the
built-in DTB unchanged to the kernel, thus we may not cut it
down unconditionally. Therefore enable the property removal
list option only if CONFIG_OF_DTB_PROPS_REMOVE is selected.
Marek Szyprowski [Fri, 17 Jan 2020 13:02:44 +0000 (14:02 +0100)]
arm: exynos: Read default MMC device from XOM[7:5] pins
XOM pins provide information for iROM bootloader about the boot device.
Those pins are mapped to lower bits of OP_MODE register (0x10000008),
which is common for all Exynos SoC variants. Set the default MMC device id
to reflect the boot device selected by XOM[7:5] pins (2 for the SD or 0 for
the eMMC).
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
spi: cadence-qspi: Add support for Cadence Octal SPI controller
Cadence OSPI is similar to QSPI IP except that it supports Octal IO
(8 IO lines) flashes. Add support for Cadence OSPI IP with existing
driver using new compatible
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com> Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Add support for Direct Access Controller mode of Cadence QSPI. This
allows MMIO access to SPI NOR flash providing better read performance.
Direct mode is only exercised if AHB window size is greater than 8MB.
Support for flash address remapping is also not supported at the moment
and can be added in future.
For better performance, driver uses DMA to copy data from flash in
direct mode using dma_memcpy().
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com> Tested-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com> Acked-by: Jagan Teki <jagan@amarulasolutions.com>
Current Cadence QSPI driver has few limitations. It assumes all read
operations to be in Quad mode and thus does not support SFDP parsing.
Also, adding support for new mode such as Octal mode would not be
possible with current configuration. Therefore move the driver over to spi-mem
framework. This has added advantage that driver can be used to support
SPI NAND memories too.
Hence, move driver over to new spi-mem APIs.
Please note that this gets rid of mode bit setting done when
CONFIG_SPL_SPI_XIP is defined as there does not seem to be any user to
that config option.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com> Tested-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com> Acked-by: Jagan Teki <jagan@amarulasolutions.com>
Make sure corresponding setup registers are updated depending on CS.
This ensures that driver can support QSPI flashes on ChipSelects other
than on CS0
Reported-by: Andreas Dannenberg <dannenberg@ti.com> Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com> Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Marcin Wojtas [Thu, 21 Nov 2019 04:38:47 +0000 (05:38 +0100)]
spi: prevent overriding established bus settings
The SPI stack relies on a proper bus speed/mode configuration
by calling dm_spi_claim_bus(). However the hitherto code
allowed to accidentally override those settings in
the spi_get_bus_and_cs() routine.
The initially established speed could be discarded by using
the slave platdata, which turned out to be an issue on
the platforms whose slave maximum supported frequency
is not on par with the maximum frequency of the bus controller.
This patch fixes above issue by configuring the bus from
spi_get_bus_and_cs() only in case it was not done before.
Signed-off-by: Marcin Wojtas <mw@semihalf.com> Reviewed-by: Simon Glass <sjg@chromium.org> Acked-by: Jagan Teki <jagan@amarulasolutions.com>
Bin Meng [Mon, 9 Sep 2019 13:00:03 +0000 (06:00 -0700)]
test: dm: spi: Fix sandbox dm_test_spi_find()
Per sandbox_cs_info(), sandbox spi controller only supports chip
select 0. Current test case tries to locate devices on chip select
1, and any call to spi_get_bus_and_cs() or spi_cs_info() with cs
number 1 should not return 0.
This updates the test case to handle it correctly.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Michael Walle [Tue, 17 Dec 2019 23:09:58 +0000 (00:09 +0100)]
spi: nxp_fspi: new driver for the FlexSPI controller
This is a port of the kernel's spi-nxp-fspi driver. It uses the new
spi-mem interface and does not expose the more generic spi-xfer
interface. The source was taken from the v5.3-rc3 tag.
The port was straightforward:
- remove the interrupt handling and the completion by busy polling the
controller
- remove locks
- move the setup of the memory windows into claim_bus()
- move the setup of the speed into set_speed()
- port the device tree bindings from the original fspi_probe() to
ofdata_to_platdata()
There were only some style change fixes, no change in any logic. For
example, there are busy loops where the return code is not handled
correctly, eg. only prints a warning with WARN_ON(). This port
intentionally left most functions unchanged to ease future bugfixes.
This was tested on a custom LS1028A board. Because the LS1028A doesn't
have proper clock framework support, changing the clock speed was not
tested. This also means that it is not possible to change the SPI
speed on LS1028A for now (neither is it possible in the linux driver).
Signed-off-by: Michael Walle <michael@walle.cc> Reviewed-by: Jagan Teki <jagan@amarulasolutions.com> Tested-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Simon Glass [Thu, 23 Jan 2020 18:48:25 +0000 (11:48 -0700)]
i2c: designware_i2c: Separate out the speed calculation
We want to be able to calculate the speed separately from actually setting
the speed, so we can generate the required ACPI tables. Split out the
calculation into its own function.
Drop the double underscore on __dw_i2c_set_bus_speed while we are here.
That is reserved for compiler internals.
Simon Glass [Thu, 23 Jan 2020 18:48:24 +0000 (11:48 -0700)]
i2c: designware_i2c: Move dw_i2c_speed_config to header
This is used to store the speed information for a bus. We want to provide
this to ACPI so that it can tell the kernel. Move this struct to the
header file so it can be accessed by the ACPI i2c implementation being
added later.
Simon Glass [Thu, 23 Jan 2020 18:48:14 +0000 (11:48 -0700)]
i2c: designware_i2c: Rewrite timing calculation
At present the driver can end up with timing parameters which are slightly
faster than those expected. It is possible to optimise the parameters to
get the best possible result.
Create a new function to handle the timing calculation. This uses a table
of defaults for each speed mode rather than writing it in code.
The function works by calculating the 'period' of each bit on the bus in
terms of the input clock to the controller (IC_CLK). It makes sure that
the constraints are met and that the different components of that period
add up correctly.
This code was taken from coreboot which has ended up with this same
driver, but now in a much-different form.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Heiko Schocher <hs@denx.de>
Simon Glass [Thu, 23 Jan 2020 18:48:12 +0000 (11:48 -0700)]
i2c: designware_i2c: Drop scl_sda_cfg parameter
Instead of passing this parameter into __dw_i2c_set_bus_speed(), pass in
the driver's private data, from which the function can obtain that
information. This allows the function to have access to the full state of
the driver.
Simon Glass [Thu, 23 Jan 2020 18:48:07 +0000 (11:48 -0700)]
i2c: designware_i2c: Rename 'max' speed to 'high' speed
Some SoCs support a higher speed than what is currently called 'max' in
this driver. Rename it to 'high' speed, which is the official name of the
3.4MHz speed.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Jun Chen <ptchentw@gmail.com> Reviewed-by: Heiko Schocher <hs@denx.de>
Simon Glass [Thu, 23 Jan 2020 18:48:06 +0000 (11:48 -0700)]
i2c: designware_i2c: Include clk.h in the header file
We use struct clk here so really should include this header file to avoid
build errors. Also switch the order of clk.h in the C file to match the
required code style.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Ley Foon Tan <ley.foon.tan@intel.com> Reviewed-by: Jun Chen <ptchentw@gmail.com> Reviewed-by: Heiko Schocher <hs@denx.de>
Pedro Jardim [Thu, 23 Jan 2020 13:21:05 +0000 (10:21 -0300)]
clock_imx8mq: Remove the function sscg_pll_init()
Function sscg_pll_init() is not used anywhere, so it can simply be deleted.
This was found because of the following sparse
warning:
arch/arm/mach-imx/imx8m/clock_imx8mq.c:702:5: warning: no previous prototype for ‘sscg_pll_init’ [-Wmissing-prototypes]
int sscg_pll_init(u32 pll)
^~~~~~~~~~~~~
Signed-off-by: Pedro Jardim <jardim.c.pedro@gmail.com>
Pedro Jardim [Thu, 23 Jan 2020 13:20:51 +0000 (10:20 -0300)]
clock_imx8mq: Make do_imx8m_showclocks() static
Since do_imx8m_showclocks() is only used inside this file, make it 'static'.
This fixes the following sparse warning:
arch/arm/mach-imx/imx8m/clock_imx8mq.c:836:5: warning: no previous prototype
for ‘do_imx8m_showclocks’ [-Wmissing-prototypes]
int do_imx8m_showclocks(cmd_tbl_t *cmdtp, int flag, int argc,
^~~~~~~~~~~~~~~~~~~
Signed-off-by: Pedro Jardim <jardim.c.pedro@gmail.com>
Joel Johnson [Sun, 26 Jan 2020 16:48:58 +0000 (09:48 -0700)]
arm: mvebu: fix A38x breakage from commit bb872dd930cc
This function parameter usage of load_addr was incorrectly caught in
the clarifying renames of commit bb872dd930cc, which results in boot
failures on Marvell A38x.
Signed-off-by: Joel Johnson <mrjoel@lixil.net> Patch-to: Simon Glass <sjg@chromium.org>
Andre Przywara [Fri, 10 Jan 2020 01:47:32 +0000 (01:47 +0000)]
sunxi: Automate loading from 128KB MMC offset
Since commit 067e0b9684d4 ("sunxi: Allow booting from 128KB SD/eMMC offset")
we support having the SPL loaded from either the traditional 8KB SD
card/eMMC offset, or from the alternative location at 128KB. However the
sector to find the U-Boot image was still hard-coded at compile time,
and had to be adjusted for one of the two choices.
Since we can actually override the function to return the sector offset,
we can just check the boot source byte there to select the proper offset
based on from where the SPL was loaded.
This allows the very same binary image to be loaded from either 128KB or
8KB, with the U-Boot proper image always being located just behind the SPL.
Signed-off-by: Andre Przywara <andre.przywara@arm.com> Acked-by: Jagan Teki <jagan@amarulasolutions.com>
Andre Przywara [Fri, 10 Jan 2020 01:47:31 +0000 (01:47 +0000)]
sunxi: SPL: Factor out sunxi_get_boot_source()
The Boot ROM write some boot source ID (SD card, eMMC, SPI, ...) into
a certain location in SRAM, so the SPL can easily determine where to
load U-Boot proper from.
Factor out reading this value, as it will come in handy again shortly.
Signed-off-by: Andre Przywara <andre.przywara@arm.com> Acked-by: Jagan Teki <jagan@amarulasolutions.com>
Giulio Benetti [Thu, 12 Dec 2019 22:53:19 +0000 (23:53 +0100)]
clk: uclass: clk_get_by_name() must not be available if CONFIG_OF_PLATDATA is enabled
clk_get_by_name() requires clk_get_by_id() that is not available if
CONFIG_OF_PLATDATA is defined, so move clk_get_by_name() into #else
condition of #if CONFIG_IS_ENABLED(OF_PLATDATA).
Fabien Parent [Thu, 17 Oct 2019 19:02:05 +0000 (21:02 +0200)]
clk: mediatek: use unsigned type for returning the clk rate
mtk_clk_find_parent_rate is calling clk_get_rate to know the rate
of a parent clock. clk_get_rate returns a ulong, while
mtk_clk_find_parent_rate returns an int. This implicit cast creates
an issue for clock rates big enough to need the full 32 bits to
store its data. When that happen the clk rate will become incorrect
because of the implicit cast between ulong -> int -> ulong.
This commit change the return type of mtk_clk_find_parent_rate to
ulong.
On m68k, block_cache list is relocated, but next and prev list
pointers are not adjusted to the relocated struct list_head address,
so the first iteration over the block_cache list hangs.
This patch initializes the block_cache list after relocation.
Signed-off-by: Angelo Durgehello <angelo.dureghello@timesys.com> Reviewed-by: Eric Nelson <eric@nelint.com>
Now that arch specific dma mapping APIs take care of cache
flush/invalidate, drop local cache flush operation.
While at that fix dma_unmap_single() call to match new prototype