Tom Rini [Thu, 18 Nov 2021 23:25:19 +0000 (18:25 -0500)]
Merge branch '2021-11-18-regression-fixes'
- An assortment of fixes related to GD, GD_FLG_SKIP_RELOC, and the lmb
- Environment fix on synquacer developmentbox
- Fix for get_info is not valid in partition code
Marek Vasut [Sat, 13 Nov 2021 17:34:37 +0000 (18:34 +0100)]
lmb: Reserve U-Boot separately if relocation is disabled
In case U-Boot starts with GD_FLG_SKIP_RELOC, the U-Boot code is
not relocated, however the stack and heap is at the end of DRAM
after relocation. Reserve a LMB area for the non-relocated U-Boot
code so it won't be overwritten.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Simon Glass <sjg@chromium.org> Cc: Tom Rini <trini@konsulko.com>
Marek Vasut [Sat, 13 Nov 2021 17:34:04 +0000 (18:34 +0100)]
board_f: Copy GD to new GD even if relocation disabled
Even if U-Boot has relocation disabled via GD_FLG_SKIP_RELOC , the
relocated stage of U-Boot still picks GD from new_gd location. The
U-Boot itself is not relocated, but GD might be, so copy the GD to
new GD location even if relocation is disabled.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Peng Fan <peng.fan@oss.nxp.com> Cc: Simon Glass <sjg@chromium.org> Cc: Tom Rini <trini@konsulko.com>
Masami Hiramatsu [Thu, 18 Nov 2021 05:45:25 +0000 (14:45 +0900)]
Revert "board: synquacer: developerbox: Don't set gd->env_addr to default_environment"
Without default setting of gd->env_addr, U-Boot will cause
a synchronous abort if the env-variables on the SPI flash is
broken or not saved corectly. Set gd->env_addr correctly.
Without get_desc, the tpm command will not provide a
description of the device in 'tpm device' or 'tpm info'.
Due to the characteristics of the Atmel TPM it isn't
possible to determine certain attributes (e.g open/close
status) without using the TPM stack (compare Infineon
and ST TPM drivers), so just print out the chip model
and udevice name as the identifier.
Mathew McBride [Thu, 11 Nov 2021 04:06:27 +0000 (04:06 +0000)]
cmd: tpm-v1: fix load_key_by_sha1 compile errors
This command is not compiled by default and has not been updated alongside
changes to the tpmv1 API, such as passing the TPM udevice to the relevant
functions.
Tom Rini [Tue, 16 Nov 2021 14:51:04 +0000 (09:51 -0500)]
Merge tag 'xilinx-for-v2022.01-rc3' of https://source.denx.de/u-boot/custodians/u-boot-microblaze
Xilinx changes for v2022.01-rc3
sdhci:
- Fix emmc mini case with missing firmware interface
zynqmp:
- Restore JTAG interface if required
- Allow overriding board name
- Add support for DLC21
- Fix one fallthrought statement description
- Use config macro instead of name duplication
- Save multiboot to variable
firmware:
- Handle ipi_req errors better
- Use local buffer in case user doesn't need it instead of NULL/0 location
Andy Shevchenko [Mon, 8 Nov 2021 18:03:38 +0000 (21:03 +0300)]
image: Explicitly declare do_bdinfo()
Compiler is not happy:
common/image-board.c: In function ‘boot_get_kbd’:
common/image-board.c:902:17: warning: implicit declaration of function ‘do_bdinfo’ [-Wimplicit-function-declaration]
902 | do_bdinfo(NULL, 0, 0, NULL);
| ^~~~~~~~~
Move the forward declaration to a header.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Masami Hiramatsu [Wed, 10 Nov 2021 00:40:07 +0000 (09:40 +0900)]
configs: synquacer: Fix dfu_alt_info to use nor1
Fix dfu_alt_info to use nor1 instead of the device name.
This reverts a part of commit 59bd18d4c4d7 ("configs: synquacer:
Remove mtdparts settings and update DFU setting") because the
commit a4f2d8341455 ("mtd: spi: nor: force mtd name to "nor%d"")
changed the mtd device naming scheme to nor%d.
The subdivision name "TQ Components" hasn't been in use for a long time.
Rename the vendor directory to "tq", which also matches our Device Tree
vendor prefix.
Alistair Delva [Wed, 20 Oct 2021 21:31:32 +0000 (21:31 +0000)]
arm64: relocate-rela: Add support for ld.lld
Cap end of relocations by the binary size.
Linkers like to insert some auxiliary sections between .rela.dyn and
.bss_start. These sections don't make their way to the final binary, but
reloc_rela still tries to relocate them, resulting in attempted read
past the end of file.
When linking U-Boot with ld.lld, the STATIC_RELA feature (enabled by
default on arm64) breaks the build. After this patch, U-Boot can be
linked successfully with and without CONFIG_STATIC_RELA.
Originally-from: Elena Petrova <lenaptr@google.com> Signed-off-by: Alistair Delva <adelva@google.com> Cc: David Brazdil <dbrazdil@google.com> Cc: Scott Wood <scottwood@freescale.com> Cc: Tom Rini <trini@konsulko.com>
Simon Glass [Mon, 1 Nov 2021 01:17:03 +0000 (19:17 -0600)]
Makefile: Correct TPL rule for OF_REAL
Correct an error in the tpl-dtb parameter to binman. At present the TPL
rule follows SPL but this is not correct, if TPL uses of-platdata, for
example.
Fixes: f99cbe4e867 ("fdt: Update Makefile rules with the new OF_REAL Kconfig") Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Marek Behún [Wed, 3 Nov 2021 23:23:23 +0000 (00:23 +0100)]
env: Simplify env_get_default()
Instead of pretending that we don't have environment to force searching
default environment in env_get_default(), get the data from the
default_environment[] buffer directly.
Signed-off-by: Marek Behún <marek.behun@nic.cz> Reviewed-by: Simon Glass <sjg@chromium.org>
Simon Glass [Thu, 4 Nov 2021 03:09:18 +0000 (21:09 -0600)]
binman: Support updating the dtb in an ELF file
WIth EFI we must embed the devicetree in an ELF image so that it is loaded
as part of the executable file. We want it to include the binman
definition in there also, which in some cases cannot be created until the
ELF (u-boot) is built. Add an option to binman to support writing the
updated dtb to the ELF file u-boot.out
This is useful with the EFI app, which is always packaged as an ELF file.
Simon Glass [Thu, 4 Nov 2021 03:09:16 +0000 (21:09 -0600)]
binman: Support reading the offset of an ELF-file symbol
Binman needs to be able to update the contents of an ELF file after it has
been build. To support this, add a function to locate the position of a
symbol's contents within the file.
Fix the comments on bss_data.c and Symbol while we are here.
Tom Rini [Mon, 8 Nov 2021 03:59:50 +0000 (22:59 -0500)]
Remove CONFIG_SERIAL_MULTI
This symbol has been functionally dead for a long time. Remove the last
and recent re-introductions of setting it, and update the whitelist so
it will not be re-introduced again.
Tom Rini [Mon, 8 Nov 2021 03:59:38 +0000 (22:59 -0500)]
Convert CONFIG_ENV_IS_IN_SPI_FLASH et al to Kconfig
This converts the following to Kconfig:
CONFIG_ENV_IS_IN_SPI_FLASH
CONFIG_ENV_IS_NOWHERE
CONFIG_ENV_OFFSET
CONFIG_ENV_OVERWRITE
CONFIG_ENV_SECT_SIZE
CONFIG_SYS_MMC_ENV_DEV
CONFIG_SYS_MMC_ENV_PART
Tom Rini [Fri, 12 Nov 2021 15:14:24 +0000 (10:14 -0500)]
Merge branch '2021-11-12-assorted-updates'
- A number of pxe related cleanups and related re-organization.
- A few related pxe/sysboot/extlinux improvements
- Remove some dead code.
- Update Azure to use a newer Windows build environment
- Add a .get_maintainer.conf file
- A few minor TI SoC platform updates
Jan Kiszka [Wed, 3 Nov 2021 14:12:30 +0000 (15:12 +0100)]
boards: siemens: iot2050: Ignore network errors during bootstage tracking
We need to filter out NET_ETH_START errors because we have to enable
networking in order to propagate the MAC addresses to the DT while there
is no network driver for the prueth in U-Boot yet.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Commit 4b2be78ab66c ("time: Fix get_ticks being non-monotonic") has
broken boot on chiliboard platform, as it requires '/chosen/tick-timer'
in device-tree. This resulted in following panic message:
Could not initialize timer (err -19)
Provide missing chosen property in device-tree to fix chiliboard
support.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Michael Walle [Sun, 31 Oct 2021 22:38:12 +0000 (23:38 +0100)]
get_maintainer.pl: add .get_maintainer.conf
Since commit e57c7c5c4282 ("get_maintainer.pl: update from Linux kernel
v5.13-rc6") only the top level MAINTAINERS file is used. This is because
this commit (accidentally) disabled the search of MAINTAINERS files
(find_maintainer_files is set to 0 again). Before that, commit b79372ae94fb ("scripts/get_maintainer.pl: enable find_maintainer_files")
explicitly enabled that feature. Nowadays, we also have to set
maintainer_path to a directory.
To fix it and enable recursive search of MAINTAINERS, create a
configuration file to set these two variables.
Tom Rini [Sun, 31 Oct 2021 17:24:42 +0000 (13:24 -0400)]
Azure: Move to windows-2019
As per https://github.com/actions/virtual-environments/issues/4312 the
Windows-2016 environments are scheduled for deprecation and removal in
early 2022. Move to windows-2019 now to avoid this (Visual Studio 2019
is included here, hence the tag naming scheme change).
Signed-off-by: Tom Rini <trini@konsulko.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Thomas Huth [Tue, 26 Oct 2021 12:31:18 +0000 (14:31 +0200)]
Remove LYNX KDI remainders
The last board that used to set CONFIG_LYNXKDI has been removed in
commit 242836a893ae ("powerpc: ppc4xx: remove pcs440ep support"),
doc/README.lynxkdi only talks about a MPC8260 board being supported,
and the mpc8260 support has been removed four years ago in commit 2eb48ff7a210d ("powerpc, 8260: remove support for mpc8260") already,
and common/lynxkdi.c only consists of an "#error" statement these
days, so it seems like the LYNX KDI code is dead code nowadays.
Let's remove it now.
Simon Glass [Thu, 14 Oct 2021 18:48:11 +0000 (12:48 -0600)]
pxe: Allow calling the pxe_get logic directly
Refactor this code so that we can call the 'pxe get' command without going
through the command-line interpreter. This makes it easier to get the
information we need, without going through environment variables.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Artem Lapkin <email2tema@gmail.com> Tested-by: Artem Lapkin <email2tema@gmail.com> Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Simon Glass [Thu, 14 Oct 2021 18:48:09 +0000 (12:48 -0600)]
pxe: Refactor sysboot to have one helper
The only difference between the three helpers is the filesystem type.
Factor this out and call the filesystem functions directly, instead of
through the command-line interpreter. This allows the file size to be
obtained directly, instead of via an environment variable.
We cannot do the same thing with PXE's tftpboot since there is no API
at present to obtain information about the file that was read. So there
is no point in changing pxe_getfile_func to use a ulong for the address,
for example.
This is as far as the refactoring can go for the present.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Artem Lapkin <email2tema@gmail.com> Tested-by: Artem Lapkin <email2tema@gmail.com> Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Simon Glass [Thu, 14 Oct 2021 18:48:08 +0000 (12:48 -0600)]
pxe: Return the file size from the getfile() function
It is pretty strange that the pxe code uses the 'filesize' environment
variable find the size of a file it has just read.
Partly this is because it uses the command-line interpreter to parse its
request to load the file.
As a first step towards unwinding this, return it directly from the
getfile() function. This makes the code a bit longer, for now, but will be
cleaned up in future patches.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Artem Lapkin <email2tema@gmail.com> Tested-by: Artem Lapkin <email2tema@gmail.com> Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Simon Glass [Thu, 14 Oct 2021 18:48:00 +0000 (12:48 -0600)]
pxe: Move pxe_utils files
Move the header file into the main include/ directory so we can use it
from the bootmethod code. Move the C file into boot/ since it relates to
booting.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Artem Lapkin <email2tema@gmail.com> Tested-by: Artem Lapkin <email2tema@gmail.com> Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Simon Glass [Thu, 14 Oct 2021 18:47:56 +0000 (12:47 -0600)]
pxe: Use a context pointer
At present the PXE functions pass around a pointer to command-table entry
which is very strange. It is only needed in a few places and it is odd to
pass around a data structure from another module in this way.
For bootmethod we will need to provide some context information when
reading files.
Create a PXE context struct to hold the command-table-entry pointer and
pass that around instead. We can then add more things to the context as
needed.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Artem Lapkin <email2tema@gmail.com> Tested-by: Artem Lapkin <email2tema@gmail.com> Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Simon Glass [Thu, 14 Oct 2021 18:47:54 +0000 (12:47 -0600)]
Create a new boot/ directory
Quite a lot of the code in common/relates to booting and images. Before
adding more it seems like a good time to move the code into its own
directory.
Most files with 'boot' or 'image' in them are moved, except:
- autoboot.c which relates to U-Boot automatically running a script
- bootstage.c which relates to U-Boot timing
Drop the removal of boot* files from the output directory, since this
interfers with the symlinks created by tools and there does not appear
to be any such file from my brief testing.
- device-tree sync-up with Linux for ls1028a
- fixes/update in fsl-ddr driver, fsl-validate, lx2162a, fsl-mc,
spintable code, configs, qspi node, pci
- enable EFI_SET_TIME support in sl28
- powerpc: Drop -mstring
projects / u-boot.git / log