Fixup port_mac_address property in MC DPC with values from the u-boot
environment. Since u-boot already reads the environment MAC addresses
when probing the PHYs, use these values.
The u-boot environment MAC addresses take precedence over any eventual
ones defined in the DPC, except for the case where they are randomly
assigned (no u-boot env value declared for port).
The patch assumes the "/board_info/ports/" node is present in the DPC.
Signed-off-by: Bogdan Purcareata <bogdan.purcareata@nxp.com> Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
[York S: Fix several indentations] Reviewed-by: York Sun <york.sun@nxp.com>
Tang Yuantian [Fri, 20 Jan 2017 09:12:48 +0000 (17:12 +0800)]
armv8: ls1046a: added usb nodes in dts
The LS1046A processor has three integrated USB 3.0 controllers
(USB1, USB2, and USB3) that allow direct connection to the USB
ports with appropriate protection circuitry and power supplies.
USB1 and USB2 ports are powered by a NX5P2190UK device, which
supplies 5v power at up to 1.2 A. The power enable and
power-fault-detect pins are connected to the LS1046A processor
via CPLD for individual port management.
Signed-off-by: Tang Yuantian <yuantian.tang@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
Tang Yuantian [Fri, 20 Jan 2017 09:12:14 +0000 (17:12 +0800)]
armv8: ls1046aqds: added usb feature support
The LS1046AQDS processor has three integrated USB 3.0 controllers
(USB1, USB2, and USB3) that allow direct connection to the USB
ports with appropriate protection circuitry and power supplies.
USB1 and USB2 ports are powered by a NX5P2190UK device, which
supplies 5v power at up to 1.2 A. The power enable and
power-fault-detect pins are connected to the LS1046A processor
via CPLD for individual port management.
Signed-off-by: Tang Yuantian <yuantian.tang@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
Ladislav Michl [Thu, 19 Jan 2017 10:45:35 +0000 (11:45 +0100)]
cmd: ubi: allow '-' to specify maximum volume size
Currently maximum volume size can be specified only if no other
arguments are used. Use '-' placeholder as volume size to allow
maximum volume size to be specified together with volume id and
type.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Stefan Roese [Fri, 9 Dec 2016 14:03:28 +0000 (15:03 +0100)]
mmc: Add Marvell Xenon SDHCI controller driver
This driver implementes platform specific code for the Xenon SDHCI
controller which is integrated in the Marvell MVEBU Armada 37xx and
Armada 7k / 8K SoCs.
History:
This driver is ported from the Marvell U-Boot version 2015.01 which is
written by Victor Gu <xigu@marvell.com> with minor changes ported from
the Linux driver which is written by Ziji Hu <huziji@marvell.com>.
Stefan Roese [Mon, 12 Dec 2016 07:24:56 +0000 (08:24 +0100)]
mmc: sdhci: Add support for optional controller specific set_ios_post()
Some SDHCI drivers might need to do some special controller configuration
after the common clock set_ios() function has been called (speed / width
configuration). This patch adds a call to the newly created function
set_ios_port() when its configured in the host driver.
This will be used by the Xenon SDHCI controller driver used on the
Marvell Armada 3700 and 7k/8k ARM64 SoCs.
Signed-off-by: Stefan Roese <sr@denx.de> Cc: Jaehoon Chung <jh80.chung@samsung.com> Cc: Simon Glass <sjg@chromium.org> Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Stefan Roese [Mon, 12 Dec 2016 07:34:42 +0000 (08:34 +0100)]
mmc: sdhci: Clear SDHCI_CLOCK_CONTROL before configuring the new value
This patch completely clears the SDHCI_CLOCK_CONTROL register before the
new value is configured instead of just clearing the 2 bits
SDHCI_CLOCK_CARD_EN and SDHCI_CLOCK_INT_EN. Without this change, some
clock configurations will lead to the "Internal clock never stabilised."
error message on the Xenon SDHCI controller used on the Marvell Armada
3700 and 7k/8k ARM64 SoCs.
The Linux SDHCI core driver also writes 0 to this register before
the new value is configured. So this patch simplifies the driver a bit
and brings the U-Boot driver more in-line with the Linux one.
Tony O'Brien [Fri, 6 Jan 2017 04:29:45 +0000 (17:29 +1300)]
powerpc: Enable flush and invalidate dcache by range for MPC85xx
Commit ac337168a unified functions to flush and invalidate dcache by
range. These two functions were no-ops for SoCs other than 4xx and
MPC86xx. Adding these functions seemed to be correct but introduced
issues in some drivers when the dcache was flushed. While the root
cause was under investigation, these functions were disabled in
Commit cb1629f91a for affected SoCs, including the MPC85xx, to make
the various drivers work.
On the T208x USB stopped working after v2016.07 was pulled. After
re-enabling the dcache functions for the MPC85xx it started working
again. The USB and DPPA Ethernet drivers have been seen as
operational after this change but other drivers cannot be tested.
Reviewed-by: Chris Packham <chris.packham@alliedtelesis.co.nz> Signed-off-by: Tony O'Brien <tony.obrien@alliedtelesis.co.nz> Cc: Marek Vasut <marex@denx.de> Cc: York Sun <york.sun@nxp.com> Reviewed-by: York Sun <york.sun>
Tony O'Brien [Thu, 1 Dec 2016 20:22:34 +0000 (09:22 +1300)]
mpc85xx: pcie: Implement workaround for Erratum A007815
The read-only-write-enable bit is set by default and must be cleared
to prevent overwriting read-only registers. This should be done
immediately after resetting the PCI Express controller.
Reviewed-by: Hamish Martin <hamish.martin@alliedtelesis.co.nz> Signed-off-by: Tony O'Brien <tony.obrien@alliedtelesis.co.nz>
[York S: Move SYS_FSL_ERRATUM_A007815 to Kconfig] Reviewed-by: York Sun <york.sun@nxp.com>
Darwin Dingel [Mon, 24 Oct 2016 20:48:01 +0000 (09:48 +1300)]
powerpc: mpc85xx: Implemente workaround for CPU erratum A-007907
Core hang occurs when using L1 stashes. Workaround is to disable L1
stashes so software uses L2 cache for stashes instead.
Reviewed-by: Chris Packham <chris.packham@alliedtelesis.co.nz> Signed-off-by: Darwin Dingel <darwin.dingel@alliedtelesis.co.nz> Cc: York Sun <york.sun@nxp.com>
[York S: Move SYS_FSL_ERRATUM_A007907 to Kconfig] Reviewed-by: York Sun <york.sun@nxp.com>
Tom Rini [Mon, 23 Jan 2017 22:40:22 +0000 (17:40 -0500)]
travis-ci: Add swig and libpython-dev to the package list
As part of 1905c8fc711a we introduced failures depending on if swig and
libpython-dev are installed or not. To provide coverage for this are of
code in the future ensure we have these packages installed.
Signed-off-by: Tom Rini <trini@konsulko.com> Reviewed-by: Heiko Schocher <hs@denx.de>
Andrew F. Davis [Mon, 23 Jan 2017 17:34:37 +0000 (11:34 -0600)]
mach-omap2: Cleanup secure boot media generation
Currently all secure media types of SPL are generated for all platforms,
all platforms do not need all types, only generate the media types valid
for each platform.
Signed-off-by: Andrew F. Davis <afd@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com> Tested-by: Lokesh Vutla <lokeshvutla@ti.com>
Tom Rini [Mon, 23 Jan 2017 00:43:11 +0000 (19:43 -0500)]
Kconfig: Migrate BOARD_LATE_INIT to a select
This option should not really be user selectable. Note that on PowerPC
we currently only need BOARD_LATE_INIT when CHAIN_OF_TRUST is enabled so be
conditional on that.
Signed-off-by: Tom Rini <trini@konsulko.com> Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com> (for UniPhier)
Tuomas Tynkkynen [Sun, 22 Jan 2017 23:34:39 +0000 (01:34 +0200)]
rpi: Fix device tree path on ARM64
The directory structure of device tree files produced by the kernel's
'make dtbs_install' is different on ARM64, the RPi3 device tree file is
in a 'broadcom' subdirectory there.
Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com> Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Jagan Teki [Tue, 10 Jan 2017 10:18:43 +0000 (11:18 +0100)]
mmc: Print error code for mmc_complete_init failure
Print the error code for non-zero (failure case) instead
of making debug statement without any condition, this
usually gives proper clue in failure condition.
mmc: sdhci: Distinguish between base clock and maximum peripheral frequency
The sdhci controller assumes that the base clock frequency is fully supported by
the peripheral and doesn't support hardware limitations. The Linux kernel
distinguishes between base clock (max_clk) of the host controller and maximum
frequency (f_max) of the card interface. Use the same differentiation and allow
the platform to constrain the peripheral interface.
Signed-off-by: Stefan Herbrechtsmeier <stefan.herbrechtsmeier@weidmueller.com>
Masahiro Yamada [Sat, 21 Jan 2017 09:05:28 +0000 (18:05 +0900)]
ARM: dts: uniphier: compile only DT files that make sense
All the UniPhier DT files are compiled if CONFIG_ARCH_UNIPHIER
is enabled, but not all of them actually work. For example, when
U-Boot is compiled for ARM 32 bit, 64 bit DT files are also built,
and vice versa. Compile only the combination that makes sense.
Masahiro Yamada [Sat, 21 Jan 2017 09:05:27 +0000 (18:05 +0900)]
ARM: uniphier: add macro to generate SoC data look-up function
There are similar functions that look up SoC data by the SoC ID.
The new macro UNIPHIER_DEFINE_SOCDATA_FUNC will be helpful to
avoid the code duplication.
Masahiro Yamada [Sat, 21 Jan 2017 09:05:26 +0000 (18:05 +0900)]
ARM: uniphier: simplify SoC ID get function
Currently, uniphier_get_soc_type() converts the SoC ID (this is
read from the revision register) to an enum symbol to use it for SoC
identification. Come to think of it, there is no need for the
conversion in the first place. Using the SoC ID from the register
as-is a straightforward way.
Masahiro Yamada [Sat, 21 Jan 2017 09:05:25 +0000 (18:05 +0900)]
ARM: uniphier: replace <common.h> with <linux/delay.h> where possible
The <common.h> includes too many headers. Actually, these files
needed to include it for udelay() declaration. Now we can replace
it with <linux/delay.h> thanks to commit 5bc516ed661a ("delay:
collect {m, n, u}delay declarations to include/linux/delay.h").
Masahiro Yamada [Sat, 21 Jan 2017 09:05:24 +0000 (18:05 +0900)]
ARM: uniphier: replace <linux/err.h> with <linux/errno.h>
These files only need error number macros. Actually, IS_ERR(),
PTR_ERR(), ERR_PTR(), etc. are not useful for U-Boot. Avoid
unnecessary header includes.
Masahiro Yamada [Sat, 21 Jan 2017 09:05:23 +0000 (18:05 +0900)]
ARM: uniphier: add uniphier_v8_defconfig
This defconfig does not support SPL. If you use this, the basic
SoC initialization must be done in firmware that runs before U-Boot.
(Generally, ARM Trusted Firmware is expected to do this job).
Masahiro Yamada [Sat, 21 Jan 2017 09:05:22 +0000 (18:05 +0900)]
ARM: uniphier: make SPL optional for ARVv8 SoCs
We may want to run different firmware before running U-Boot. For
example, ARM Trusted Firmware runs before U-Boot, making U-Boot
a non-secure world boot loader. In this case, the SoC might be
initialized there, which enables us to skip SPL entirely.
This commit removes "select SPL" to make it configurable. This
also enables the Multi SoC support for the UniPhier ARMv8 SoCs.
(CONFIG_ARCH_UNIPHIER_V8_MULTI) Thanks to the driver model and
Device Tree, the U-Boot proper part is now written in a generic way.
The board/SoC parameters reside in DT. The Multi SoC support
increases the memory footprint a bit, but the U-Boot proper does
not have strict memory constraint. This will mitigate the per-SoC
(sometimes per-board) defconfig burden.
Uri Mashiach [Thu, 19 Jan 2017 08:51:45 +0000 (10:51 +0200)]
status_led: Kconfig migration
Move all of the status LED feature to drivers/led/Kconfig.
The LED status definitions were moved from the board configuration
files to the defconfig files.
TBD: Move all of the definitions in the include/status_led.h to the
relevant board's defconfig files.
Tested boards: CL-SOM-AM57x, CM-T335
Signed-off-by: Uri Mashiach <uri.mashiach@compulab.co.il>
Tom Rini [Sat, 21 Jan 2017 00:55:53 +0000 (19:55 -0500)]
mx6saberesd_spl: Correct falcon mode addition
When falcon mode support was added, it was right around when SPL_OS_BOOT
was migrated to Kconfig. So first we must move the enablement to the
defconfig file. Next, it turned off EXT support rather than add the
information to allow for falcon mode from EXT. Add this information so
that the board compiles after 5d28b930f237.
Emmanuel Vadot [Thu, 19 Jan 2017 09:23:56 +0000 (10:23 +0100)]
bootm: qnx: Disable data cache before booting QNX image
Instead of disabling the data cache in the bootelf command, disabling
it in the do_bootm_qnxelf function.
Some ELF binary might want the cache enabled.
Lokesh Vutla [Tue, 17 Jan 2017 03:22:58 +0000 (08:52 +0530)]
ARM: OMAP4: Fix compiler warning
Latest gcc 6.2 compiler is throwing the below warning for omap4_panda_defconfig
arch/arm/mach-omap2/omap4/hw_data.c:136:3: warning: 'abe_dpll_params_sysclk_196608khz' defined but not used [-Wunused-const-variable=]
abe_dpll_params_sysclk_196608khz[NUM_SYS_CLKS] = {
Fix this by guarding it with CONFIG_SYS_OMAP_ABE_SYSCK
Reported-by: Dan Murphy <dmurphy@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Emmanuel Vadot [Mon, 16 Jan 2017 07:14:46 +0000 (08:14 +0100)]
binman: add tools directory to the python path
The built _libfdt.so is placed in the /tools dir and need to say here
as it contains relative paths.
Add the directory to the python path so binman can use this module.
Tom Rini [Thu, 12 Jan 2017 18:16:03 +0000 (13:16 -0500)]
board_init.c: Always use memset()
We can make the code read more easily here by simply using memset()
always as when we don't have an optimized version of the function we
will still have a version of this function around anyhow.
Cc: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Rini <trini@konsulko.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Tom Rini [Thu, 12 Jan 2017 18:16:02 +0000 (13:16 -0500)]
ARM: Default to using optimized memset and memcpy routines
We have long had available optimized versions of the memset and memcpy
functions that are borrowed from the Linux kernel. We should use these
in normal conditions as the speed wins in many workflows outweigh the
relatively minor size increase. However, we have a number of places
where we're simply too close to size limits in SPL and must be able to
make the size vs performance trade-off in those cases.
Cc: Philippe Reynes <tremyfr@yahoo.fr> Cc: Eric Jarrige <eric.jarrige@armadeus.org> Cc: Heiko Schocher <hs@denx.de> Cc: Magnus Lilja <lilja.magnus@gmail.com> Cc: Lokesh Vutla <lokeshvutla@ti.com> Cc: Chander Kashyap <k.chander@samsung.com> Cc: Akshay Saraswat <akshay.s@samsung.com> Cc: Simon Glass <sjg@chromium.org> Cc: Stefan Roese <sr@denx.de> Signed-off-by: Tom Rini <trini@konsulko.com> Acked-by: Stefan Roese <sr@denx.de> Reviewed-by: Simon Glass <sjg@chromium.org>
Andrew F. Davis [Thu, 12 Jan 2017 16:21:58 +0000 (10:21 -0600)]
mach-omap2: Fix secure boot media generation
While moving OMAP related files to mach-omap2 the functionality
relating to generating secure boot files was modified. This change
prevents secure platforms other than AM33xx and OMAP54XX from
correctly building files for all needed media types.
Fixes: 983e37007da5 ("arm: Introduce arch/arm/mach-omap2 for OMAP2 derivative platforms") Signed-off-by: Andrew F. Davis <afd@ti.com> Acked-by: Lokesh Vutla <lokeshvutla@ti.com>
Andrew F. Davis [Fri, 6 Jan 2017 19:35:45 +0000 (13:35 -0600)]
spl: Remove inline ifdef check for EXT and FAT support
These files are only included for build by the make system
when CONFIG_SPL_{EXT,FAT}_SUPPORT is enabled, remove the unneed
checks for these in the source files.
Signed-off-by: Andrew F. Davis <afd@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Emmanuel Vadot [Thu, 5 Jan 2017 05:40:21 +0000 (06:40 +0100)]
api: storage: Test all block device in dev_stor_get
In a config with one MMC at device id '1' and no MMC at device id '0'
(a BeagleBone Black with no sd inserted for example), the current code
will first test to access the MMC 0 (sd port), seeing that no device is
present it will simply return that no more device are present for this
class.
This patch fixes this by testing all devices for each class.
Emmanuel Vadot [Mon, 26 Dec 2016 17:57:56 +0000 (18:57 +0100)]
api: Use hashtable function for API_env_enum
The current code can loop undefinitly as it doesn't parse
correctly the env data.
Since the env is an hashtable, use the hashtable function for
the API_ENV_ENUM api call.
Signed-off-by: Emmanuel Vadot <manu@bidouilliste.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Some scripts are calling the same functions, so these changes consolidate
common scripts together to reduce redundancy and shrink size a bit. This
also keeps the 'bootargs' variable from growing if manually called more
than one time. This also adds NAND booting scripts based on newly consolidated
scripts.
Rick Altherr [Thu, 19 Jan 2017 01:12:24 +0000 (17:12 -0800)]
bootm: relocate ramdisk if CONFIG_SYS_BOOT_RAMDISK_HIGH set
In 35fc84f, bootm was refactored so plain 'bootm' and
'bootm <subcommand>' shared a common implementation.
The 'bootm ramdisk' command implementation is now part of the common
implementation but not invoke by plain 'bootm' since the original
implementation never did ramdisk relocation. Instead, ramdisk
relocation happened in image_setup_linux() which is typically called
during the OS portion of 'bootm'.
On ARM, parameters to the Linux kernel can either be passed by FDT or
ATAGS. When using FDT, image_setup_linux() is called which also triggers
ramdisk relocation. When using ATAGS, image_setup_linux() is _not_
called because it mostly does FDT setup.
Instead of calling image_setup_linux() in both FDT and ATAGS cases,
include BOOTM_STATE_RAMDISK in the requested states during a plain
'bootm' if CONFIG_SYS_BOOT_RAMDISK_HIGH is set and remove the ramdisk
relocation from image_setup_linux(). This causes ramdisk relocation to
happen on any system where CONFIG_SYS_BOOT_RAMDISK_HIGH regardless of
the OS being booted. Also remove IMAGE_ENABLE_RAMDISK_HIGH as it was
only used by the now-removed code from image_setup_linux().
Signed-off-by: Rick Altherr <raltherr@google.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Joel Stanley <joel@jms.id.au>
Heiko Schocher [Wed, 18 Jan 2017 07:05:49 +0000 (08:05 +0100)]
serial, ns16550: bugfix: ns16550 fifo not enabled
commit: 65f83802b7a5b "serial: 16550: Add getfcr accessor"
breaks u-boot commandline working with long commands
sending to the board.
Since the above patch, you have to setup the fcr register.
For board/archs which enable OF_PLATDATA, the new field
fcr in struct ns16550_platdata is not filled with a
default value ...
This leads in not setting up the uarts fifo, which ends
in problems, when you send long commands to u-boots
commandline.
Detected this issue with automated tbot tests on am335x
based shc board.
The error does not popup, if you type commands. You need
to copy&paste a long command to u-boots commandshell
(or send a long command with tbot)
Possible boards/plattforms with problems:
./arch/arm/cpu/arm926ejs/lpc32xx/devices.c
./arch/arm/mach-tegra/board.c
./board/overo/overo.c
./board/quipos/cairo/cairo.c
./board/logicpd/omap3som/omap3logic.c
./board/logicpd/zoom1/zoom1.c
./board/timll/devkit8000/devkit8000.c
./board/lg/sniper/sniper.c
./board/ti/beagle/beagle.c
./drivers/serial/serial_rockchip.c
Signed-off-by: Heiko Schocher <hs@denx.de> Signed-off-by: Ladislav Michl <ladis@linux-mips.org> Tested-by: Adam Ford <aford173@gmail.com> Reviewed-by: Tom Rini <trini@konsulko.com>
Yangbo Lu [Tue, 17 Jan 2017 02:43:56 +0000 (10:43 +0800)]
armv8: ls1012a: define esdhc_status_fixup for RDB board
On LS1012ARDB board, three dual 1:4 mux/demux devices drive the SDHC2
signals to eMMC, SDIO wifi, SPI and Ardiuno shield. Only when we select
eMMC and SDIO wifi, the SDHC2 could be used. Otherwise, the command
inhibit bits of eSDHC2_PRSSTAT register will never release. This would
cause below continious error messages in linux since it uses polling
mode to detect card.
"mmc1: Controller never released inhibit bit(s)."
"mmc1: Controller never released inhibit bit(s)."
"mmc1: Controller never released inhibit bit(s)."
This patch is to define esdhc_status_fixup function for RDB to disable
SDHC2 status if no SDIO wifi or eMMC is selected.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
Yangbo Lu [Tue, 17 Jan 2017 02:43:55 +0000 (10:43 +0800)]
armv8: ls1012a: define esdhc_status_fixup for QDS board
The LS1012AQDS board has a hardware issue. When there is no eMMC
adapter card inserted in SDHC2 adapter slot, the command inhibit
bits of eSDHC2_PRSSTAT register will never release. This would cause
below continious error messages in linux since it uses polling mode
to detect card.
"mmc1: Controller never released inhibit bit(s)."
"mmc1: Controller never released inhibit bit(s)."
"mmc1: Controller never released inhibit bit(s)."
This patch is to define esdhc_status_fixup function for QDS to
disable SDHC2 status if no eMMC adapter card is detected.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
Alison Wang [Tue, 17 Jan 2017 01:39:17 +0000 (09:39 +0800)]
armv8: aarch64: Fix the warning about x1-x3 nonzero issue
For 64-bit kernel, there is a warning about x1-x3 nonzero in violation
of boot protocol. To fix this issue, input argument 4 is added for
armv8_switch_to_el2 and armv8_switch_to_el1. The input argument 4 will
be set to the right value, such as zero.
Signed-off-by: Alison Wang <alison.wang@nxp.com> Reviewed-by: Alexander Graf <agraf@suse.de> Tested-by: Ryan Harkin <ryan.harkin@linaro.org> Tested-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: York Sun <york.sun@nxp.com>
The default MSI node in kernel tree is for LS1043A rev1.0 silicon, if
rev1.1 silicon used, need to fixup the MSI node to match it.
Signed-off-by: Wenbin Song <wenbin.song@nxp.com> Signed-off-by: Mingkai Hu <mingkai.hu@nxp.com> Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
Wenbin Song [Tue, 17 Jan 2017 10:31:15 +0000 (18:31 +0800)]
armv8/ls1043a: fixup GIC offset for ls1043a rev1
The LS1043A rev1.1 silicon supports two types of GIC offset: 4K
alignment and 64K alignment. The bit SCFG_GIC400_ALIGN[GIC_ADDR_BIT]
is used to choose which offset will be used.
The LS1043A rev1.0 silicon only supports the CIG offset with 4K
alignment.
If GIC_ADDR_BIT bit is set, 4K alignment is used, or else 64K alignment
is used. 64K alignment is the default setting.
Overriding the weak smp_kick_all_cpus, the new impletment is able to
detect GIC offset.
The default GIC offset in kernel device tree is using 4K alignment, it
need to be fixed if 64K alignment is detected.
Signed-off-by: Wenbin Song <wenbin.song@nxp.com> Signed-off-by: Mingkai Hu <mingkai.hu@nxp.com> Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
Hou Zhiqiang [Fri, 9 Dec 2016 08:09:01 +0000 (16:09 +0800)]
ls1046ardb: Add support power initialization
Add the chip power supply voltage initialization on LS1046ARDB.
Add function power_init_board(), and it will initialize the
PMIC and call the chip power initialization function.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
Hou Zhiqiang [Fri, 9 Dec 2016 08:09:00 +0000 (16:09 +0800)]
armv8/fsl_lsch2: Add chip power supply voltage setup
Set up chip power supply voltage according to voltage ID.
The fuse status register provides the values from on-chip
voltage ID fuses programmed at the factory. These values
define the voltage requirements for the chip.
Main operations:
1. Set up the core voltage
2. Set up the SERDES voltage and reset SERDES lanes
3. Enable/disable DDR controller support 0.9V if needed
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
projects / u-boot.git / log