Max Krummenacher [Wed, 28 Oct 2020 09:58:11 +0000 (11:58 +0200)]
ARM: dts: imx8mm-verdin: follow changed pmic
The used PMIC has been changed from RHOM BD71837 to NXP PCA9450A.
Adjust the device tree accordingly.
Remove the old ADC node as the ADC has been changed and has no longer
a separate power rail.
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com> Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com> Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Haibo Chen [Tue, 3 Nov 2020 09:18:35 +0000 (17:18 +0800)]
mmc: fsl_esdhc_imx: optimize the timing setting
For imx usdhc/esdhc, once set the DDR_EN, enable the DDR mode, the
card clock will be divied by 2 automatically by the host. So need
to first config the DDR_EN correctly, then update the card clock.
This will make sure the actual card clock is as our expected.
IC also suggest config the DDR_EN firstly, then config the clock
divider.
For HS400/HS400ES mode, need to config the strobe dll, this need
to based on the correct target clock rate, so need to do this after
clock rate is update.
Commit f692b479f02d changed the VPD partition name from "vpd" to
"vpd@0". Fix the VPD reader code to use the new name, so that
the VPD code keeps working.
Fixes: f692b479f02d ("i2c: eeprom: Use reg property instead of offset and size") Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Oliver Graute [Fri, 6 Nov 2020 08:09:30 +0000 (09:09 +0100)]
imx: ahab: fix compiler warnings in debug
arch/arm/mach-imx/imx8/ahab.c: In function ‘authenticate_os_container’:
arch/arm/mach-imx/imx8/ahab.c:96:9: warning: format ‘%x’ expects argument of type
‘unsigned int’, but argument 9 has type ‘ulong {aka long unsigned int}’ [-Wformat=]
debug("img %d, dst 0x%x, src 0x%x, size 0x%x\n",
Oliver Graute [Fri, 6 Nov 2020 08:09:31 +0000 (09:09 +0100)]
imx: ahab: Fix compiler warnings in printf
arch/arm/mach-imx/imx8/ahab.c:110:63: warning: format ‘%x’ expects
argument of type ‘unsigned int’, but argument 2 has type ‘u64 {aka long
long unsigned int}’ [-Wformat=]
AKASHI Takahiro [Thu, 19 Nov 2020 00:37:19 +0000 (09:37 +0900)]
common: update: fix an "unused" warning against update_flash()
Since update_flash() is used only in update_tftp(), it should be
guarded with appropriate config options.
After the commit 3149e524fc1e, common/update.c will be built under
either CONFIG_UDATE_TFTP, CONFIG_DFU_TFTP or CONFIG_UPDATE_FIT.
Since CONFIG_UPDATE_FIT, hence fit_update(), doesn't rely on
update_flash(), the compiler may cause an "unused" warning if
CONFIG_UPDATE_FIT=y and CONFIG_UPDATE_TFTP=n and CONFIG_DFU_TFTP=n.
This is, for example, the case for sandbox defconfig where
EFI_CAPSULE_FIRMWARE_FIT is enabled for test purpose.
Fixes: 3149e524fc1e ("common: update: add a generic interface for FIT
image") Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Simon Glass [Mon, 30 Nov 2020 00:07:05 +0000 (17:07 -0700)]
global_data: Fix comment for dm_driver_rt
This comment is in the wrong format, so reports an error with
'make htmldocs'. Fix it.
Fixes: a294ead8d25 ("dm: Use an allocated array for run-time device info") Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Simon Glass [Mon, 30 Nov 2020 00:07:04 +0000 (17:07 -0700)]
log: Fix comment for LOGC_BOOT
This comment is in the wrong format, so reports an error with
'make htmldocs'. Fix it.
Fixes: b73d61a5565 ("x86: zimage: Add a little more logging") Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Andy Shevchenko [Thu, 19 Nov 2020 19:26:20 +0000 (21:26 +0200)]
linux/compat.h: Remove debug() from spin_lock_irqsave()
It seems nobody tested the debug() option in spin_lock_irqsave().
Currently, when #define DEBUG, it spoils the compiler with
In file included from drivers/usb/dwc3/gadget.c:18:
drivers/usb/dwc3/gadget.c: In function ‘dwc3_gadget_set_selfpowered’:
include/log.h:235:4: warning: ‘flags’ is used uninitialized in this function [-Wuninitialized]
235 | printf(pr_fmt(fmt), ##args); \
| ^~~~~~
drivers/usb/dwc3/gadget.c:1347:17: note: ‘flags’ was declared here
1347 | unsigned long flags;
| ^~~~~
and so on...
Drop useless debug() call to make compiler happy.
Fixes: 0c06db598367 ("lib, linux: move linux specific defines to linux/compat.h") Cc: Heiko Schocher <hs@denx.de> Cc: Tom Rini <trini@ti.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Reviewed-by: Oleksandr Andrushchenko <oleksandr_andrushchenko@epam.com> Reviewed-by: Heiko Schocher <hs@denx.de>
Michal Simek [Mon, 23 Nov 2020 08:08:19 +0000 (09:08 +0100)]
binman: Remove additional backslash
The origin patch didn't have this change and it was caused by manual
resolution where additional backslash was added.
Fixes: 6723b4c6ca7b ("binman: Call helper function binman_set_rom_offset() to fill offset") Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Marek Vasut [Sun, 15 Nov 2020 20:22:53 +0000 (21:22 +0100)]
dm: core: Fix incorrect flag check
The test should be checking whether $flags are non-zero and $drv_flags
contain specific flags, however these two sets of flags are separate,
and the two tests should be logically ANDed, not bitwise ANDed.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Simon Glass <sjg@chromium.org> Reviewed-by: Simon Glass <sjg@chromium.org>
sandbox: cros_ec: Basic support for EC_CMD_GET_NEXT_EVENT
Since commit 690079767803 ("cros_ec: Support keyboard scanning with
EC_CMD_GET_NEXT_EVENT") the cros-ec-keyb driver has started using this
command, but the sandbox EC emulator does not recognize it and
continuously prints:
** Unknown EC command 0x67
This patch makes the sandbox driver send basic responses to the command,
but the response only supports keyboard scans for now.
The EC side of this command stores and returns events from a queue, and
returns -EC_RES_UNAVAILABLE when there are no new events. This should be
possible to implement by hooking into the SDL event queue (perhaps via
sandbox_sdl_poll_events). Implementing that is a bit harder to do since
the existing sandbox code is discarding pending keyboard events, then
reading the current keyboard state.
Since the EC emulator never explicitly fails to work on this command,
the fallback to the older command will not trigger and will not be
tested anymore.
Fixes: 690079767803 ("cros_ec: Support keyboard scanning with EC_CMD_GET_NEXT_EVENT") Reported-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com> Tested-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Reviewed-by: Simon Glass <sjg@chromium.org>
At present if CROSS_COMPILE contains a tilde, such as
~/.buildman-toolchains/gcc-7.3.0-nolibc/i386-linux/bin/i386-linux-gcc
then binman gives a confusing error:
Add a tool to update or insert an Octeon specific header into the U-Boot
image. This is needed e.g. for booting via SPI NOR, eMMC and NAND.
While working on this, move enum cvmx_board_types_enum and
cvmx_board_type_to_string() to cvmx-bootloader.h and remove the
unreferenced (unsupported) board definition.
Signed-off-by: Stefan Roese <sr@denx.de> Cc: Aaron Williams <awilliams@marvell.com> Cc: Chandrakala Chavva <cchavva@marvell.com> Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com> Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Stefan Roese [Wed, 28 Oct 2020 14:10:02 +0000 (15:10 +0100)]
mips: octeon: bootoctlinux: Use gd->ram_size instead of ram_get_info()
Using ram_get_info() is complicated and does not work after relocation.
Now that gd->ram_size holds the full RAM size, let's use it instead and
remove the ram_get_size logic completely.
Signed-off-by: Stefan Roese <sr@denx.de> Cc: Aaron Williams <awilliams@marvell.com> Cc: Chandrakala Chavva <cchavva@marvell.com> Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com> Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Stefan Roese [Wed, 28 Oct 2020 14:10:01 +0000 (15:10 +0100)]
mips: octeon: Report full DDR size in dram_init() to gd->ram_size
With this patch, gd->ram_size now holds to full RAM size detected by the
DDR init code. It introduces the get_effective_memsize() function to
report the maximum usable RAM size in U-Boot to the system instead.
Signed-off-by: Stefan Roese <sr@denx.de> Cc: Aaron Williams <awilliams@marvell.com> Cc: Chandrakala Chavva <cchavva@marvell.com> Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com> Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Stefan Roese [Wed, 28 Oct 2020 14:10:00 +0000 (15:10 +0100)]
mips: octeon: Fix Octeon DDR driver to use the correct struct
Don't use "platdata_auto_alloc_size" but "priv_auto_alloc_size" instead
to auto allocate the private data struct, which is referenced via
dev_get_priv() in this driver. This fixes an ugly bug detected while
trying to boot via SPI NOR.
Signed-off-by: Stefan Roese <sr@denx.de> Cc: Aaron Williams <awilliams@marvell.com> Cc: Chandrakala Chavva <cchavva@marvell.com> Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Octeon has a specific boot header, when booted via SPI NOR, NAND or MMC.
Here the only 2 instructions are allowed in the first few bytes of the
image. And these instructions need to be one branch and a nop. This
patch adds the necessary nop after the nop, to that the common MIPS
image is compatible with this Octeon header.
The tool to patch the Octeon boot header into the image will be send in
a follow-up patch.
Signed-off-by: Stefan Roese <sr@denx.de> Cc: Aaron Williams <awilliams@marvell.com> Cc: Chandrakala Chavva <cchavva@marvell.com> Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com> Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Tom Rini [Sun, 29 Nov 2020 16:12:49 +0000 (11:12 -0500)]
Merge tag 'efi-2021-01-rc3-3' of https://gitlab.denx.de/u-boot/custodians/u-boot-efi
Pull request for UEFI sub-system for efi-2021-01-rc3 (3)
The following errors are corrected:
* Linux crash when accessing UEFI variables at runtime.
* UEFI variable using standalone MM on 32 bit systems
not working due to missing packing of communication
structure
* NULL dereference when FAT16 root directory is full
* FAT files with a short file name starting with 0xE5 (0x05 in directory
entry) where treated as deleted.
The UEFI SetTime() service is enabled on ARM QEMU.
Ilias Apalodimas [Sun, 22 Nov 2020 13:10:26 +0000 (15:10 +0200)]
charset: make u16_strnlen accessible at runtime
commit 1fabfeef506c ("efi_loader: parameter check in GetNextVariableName()")
introduces a check using u16_strnlen(). This code is used on EFI
runtime variables as well, so unless we mark it as runtime, the kernel
will crash trying to access it.
Fixes: 1fabfeef506c ("efi_loader: parameter check in GetNextVariableName()") Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org> Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Etienne Carriere [Sat, 21 Nov 2020 10:59:33 +0000 (11:59 +0100)]
lib/efi_loader: fix ABI in efi_mm_communicate_header
Pack struct efi_mm_communicate_header as done in EDK2 as seen in
release 201808 [1]. If not packed sizeof() for the structure adds
4 additional bytes on 32bit targets which breaks the ABI.
Baruch Siach [Thu, 1 Oct 2020 11:49:02 +0000 (14:49 +0300)]
i2c: mvtwsi: disable i2c slave also on Armada 8k
The hidden I2C slave is also present on the Armada 8k AP806. Testing
shows that this I2C slave causes the same issues as Armada 38x.
Disabling that I2C slave fixes all these issues.
I2C blocks on the Armada 8k CP110 are not affected.
Extend the I2C slave disable to Armada 8k as well.
Cc: Stefan Roese <sr@denx.de> Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Yangbo Lu [Tue, 20 Oct 2020 03:04:52 +0000 (11:04 +0800)]
mmc: fsl_esdhc: make sure delay chain locked for HS400
For eMMC HS400 mode, the DLL reset is a required step for mmc rescan.
This step has not been documented in reference manual, but the RM will
be fixed sooner or later.
In previous commit to support eMMC HS400, db8f936 mmc: fsl_esdhc: support eMMC HS400 mode
the steps to configure DLL could be found in commit message,
13. Set DLLCFG0[DLL_ENABLE] and DLLCFG0[DLL_FREQ_SEL].
14. Wait for delay chain to lock.
these would be fixed as,
13. Set DLLCFG0[DLL_ENABLE] and DLLCFG0[DLL_FREQ_SEL].
13.1 Write DLLCFG0[DLL_RESET] to 1 and wait for 1us,
then write DLLCFG0[DLL_RESET]
14. Wait for delay chain to lock.
This patch is to add the step of DLL reset, and make sure delay chain
locked for HS400.
Fixes: db8f93672b42 ("mmc: fsl_esdhc: support eMMC HS400 mode") Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com> Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Yangbo Lu [Tue, 20 Oct 2020 03:04:51 +0000 (11:04 +0800)]
mmc: fsl_esdhc: set sysctl register for clock initialization
The initial clock setting should be through sysctl register only,
while the mmc_set_clock() will call mmc_set_ios() introduce other
configurations like bus width, mode, and so on.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com> Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Sean Anderson [Sat, 17 Oct 2020 12:36:27 +0000 (08:36 -0400)]
mmc: Add some helper functions for retrying on error
All of the existing quirks add retries to various calls of mmc_send_cmd.
mmc_send_cmd_quirks is a helper function to do this retrying behavior. It
checks if quirks mode is enabled, and if a specific quirk is activated it
retries on error.
This also adds mmc_send_cmd_retry, which retries on error every time
(instead of if a quirk is activated).
Signed-off-by: Sean Anderson <seanga2@gmail.com> Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com> Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Tom Rini [Wed, 25 Nov 2020 16:00:52 +0000 (11:00 -0500)]
Merge tag 'u-boot-stm32-20201125' of https://gitlab.denx.de/u-boot/custodians/u-boot-stm
- STM32 MCU's DT update
- Add DHCOM based STM32MP15x PicoITX board
- Correct ALIGN macro usage for on syram for SPL dcache support
- Fixes on DHCOM: uSD card-detect GPIO and Drop QSPI CS2
- Fix compilation issue for spl_mmc_boot_partition
- Fix MTD partitions for serial boot
- Add support of MCU HOLD BOOT with reset for stm32 remoteproc
(prepare alligneent with kernel DT)
- Correct bias information and support in STM32 soc and STMFX
- Support optional vbus in usbphyc
- Update FIT examples to avoid kernel zImage relocation before decompression
Patrick Delaunay [Wed, 25 Nov 2020 11:28:10 +0000 (12:28 +0100)]
board: st: stm32mp1: update load address for FIT examples
Update kernel load address for FIT examples to avoid relocation:
- Kernel example uses Image.gz with U-Boot gzip decompression
at final kernel location 0x0xC0008000.
- Copro example loads zImage at a correct location (0xC4000000),
to avoid zImage relocation before decompression by kernel code.
An other solution to avoid zImage relocation is to align
the kernel load and entry address with the real location in FIT
(the relocation of zImage is skipped in U-Boot bootm command for
identical address) but it is less flexible because this offset
depends on FIT content:
For example:
## Loading kernel from FIT Image at c2000000 ...
Using 'ev1' configuration
Trying 'kernel' kernel subimage
Description: Linux kernel
Created: 2020-10-22 9:08:32 UTC
Type: Kernel Image
Compression: uncompressed
Data Start: 0xc20000cc
The kernel offset in FIT is 0xCC in FIT and zImage is decompressed at
0xC0008000 by kernel code:
Patrick Delaunay [Wed, 28 Oct 2020 09:51:56 +0000 (10:51 +0100)]
pinctrl: stmfx: update pincontrol and gpio device name
The device name is used in pinmux command and in log trace
so it is better to use the parent parent name ("stmfx@42" for
example) than a generic name ("pinctrl" or "stmfx-gpio")
to identify the device instance.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Patrick Delaunay [Wed, 28 Oct 2020 09:49:08 +0000 (10:49 +0100)]
gpio: stm32: correct the bias management
Use the bias configuration for all the GPIO configurations and not
only for input GPIO, as indicated in Reference manual
(Table 81. Port bit configuration table).
Patrick Delaunay [Wed, 28 Oct 2020 09:49:07 +0000 (10:49 +0100)]
pinctrl: stm32: display bias information for all pins
Display the bias information for input gpios or AF configuration,
and not only for output pin, as described in Reference manual
(Table 81. Port bit configuration table).
Fixes: da7a0bb1f279 ("pinctrl: stm32: add information on pin configuration") Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Patrick Delaunay [Thu, 15 Oct 2020 13:01:11 +0000 (15:01 +0200)]
reset: stm32: Add support of MCU HOLD BOOT
Handle the register RCC_MP_GCR without SET/CLR registers
but with a direct access to bit BOOT_MCU:
- deassert => set the bit: The MCU will not be in HOLD_BOOT
- assert => clear the bit: The MCU will be set in HOLD_BOOT
With this patch the RCC driver handles the MCU_HOLD_BOOT_R value
added in binding stm32mp1-resets.h
Patrick Delaunay [Thu, 15 Oct 2020 12:52:30 +0000 (14:52 +0200)]
board: stm32mp1: no MTD partitions fixup for serial boot
Remove the update of the MTD partitions in kernel device tree
for serial boot (USB / UART), and the kernel will use the MTD
partitions define in the loaded DTB because U-Boot can't known the
expected flash layout in this case.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Marek Vasut [Tue, 3 Nov 2020 18:14:58 +0000 (19:14 +0100)]
ARM: dts: stm32: Add DHCOM based PicoITX board
Add DT for DH PicoITX unit, which is a bare-bones carrier board for
the DHCOM. The board has ethernet port, USB, CAN, LEDs and a custom
board-to-board expansion connector.
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Patrice Chotard <patrice.chotard@st.com> Cc: Patrick Delaunay <patrick.delaunay@st.com> Reviewed-by: Patrice Chotard <patrice.chotard@st.com> Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Patrice Chotard [Fri, 6 Nov 2020 07:11:59 +0000 (08:11 +0100)]
ARM: dts: stm32: Fix timer initialization for stm32 MCU's board
Commit 4b2be78ab66c ("time: Fix get_ticks being non-monotonic")
puts in evidence that get_ticks is called before timer initialization.
Fix it by initializing timer before relocation.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com> Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Patrice Chotard [Fri, 6 Nov 2020 07:11:57 +0000 (08:11 +0100)]
ARM: dts: sync armv7-m.dtsi with kernel v5.10-rc1
Since kernel v4.8-rc1, commit 05b23ebc2bd9 ("ARM: dts: armv7-m: remove skeleton.dtsi include"),
skeleton.dtsi file is no more included.
This synchronization is needed to avoid to get 2 memory node
in DTB file if, in DTS file, memory node is declared with the correct
syntax as following:
Issue found when synchronizing MCU's STM32 DT from kernel v5.10-rc1.
When using fdtdec_setup_mem_size_base() or fdtdec_setup_memory_banksize()
API, first above memory node is found (with reg = <0x00 0x00>), so
gd->ram_size, gd->ram_base, gd->bd->bi_dram[bank].start and
gd->bd->bi_dram[bank].size are all set to 0 which avoid boards to boot.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com> Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
usb: dwc3: Handle case where setup_phy is not needed
If CONFIG_PHY is not enabled then the dwc3_setup_phy()
returns ENOTSUPP which can be still valid and intentional
so modify error check to handle this -ENOTSUPP.
The same error handling exists in drivers/usb/host/xhci-dwc3.c already
added by commit d648a50c0a27 ("dwc3: move phy operation to core.c").
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Patrick Delaunay [Thu, 15 Oct 2020 12:49:37 +0000 (14:49 +0200)]
usb: dwc2: add "u-boot,force-vbus-detection" for stm32
On some board, the ID pin is not connected so the B session must be
overridden with "u-boot,force_b_session_valid" but the VBus sensing
must continue to be handle.
To managed it, this patch adds a new DT field
"u-boot,force-vbus-detection" to use with "u-boot,force_b_session_valid"
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Biju Das [Wed, 28 Oct 2020 10:34:23 +0000 (10:34 +0000)]
pinctrl: renesas: r8a7796: Optimize pinctrl image size for R8A774A1
This driver supports both RZ/G2M and R-Car M3-W/W+ SoCs.
Optimize pinctrl image size for RZ/G2M, when support for R-Car M3-W/W+
(R8A7796[01]) is not enabled.
Based on the similar patch on Linux.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Biju Das [Wed, 28 Oct 2020 10:34:22 +0000 (10:34 +0000)]
pinctrl: renesas: r8a77951: Add R8A774E1 PFC support
Renesas RZ/G2H (r8a774e1) is pin compatible with R-Car H3 (r8a77951),
however it doesn't have several automotive specific peripherals. Add
a r8a77951 specific pin groups/functions along with common pin
groups/functions for supporting both r8a77951 and r8a774e1 SoC.
PFC changes are synced from mainline linux-5.9 commit bbf5c979011a ("Linux 5.9").
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com> Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Biju Das [Wed, 28 Oct 2020 10:34:21 +0000 (10:34 +0000)]
pinctrl: renesas: r8a77965: Add R8A774B1 PFC support
Renesas RZ/G2N (r8a774b1) is pin compatible with R-Car M3-N (r8a77965),
however it doesn't have several automotive specific peripherals. Add
a r8a77965 specific pin groups/functions along with common pin
groups/functions for supporting both r8a77965 and r8a774b1 SoC.
PFC changes are synced from mainline linux-5.9 commit bbf5c979011a ("Linux 5.9").
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com> Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Ilias Apalodimas [Mon, 16 Nov 2020 06:52:41 +0000 (08:52 +0200)]
efi_loader: tcg2 protocol updates
On pull reuqest
https://lists.denx.de/pipermail/u-boot/2020-November/432735.html
V4 of the patchset was sent instead of the v5.
This is the v4->v5 missing diff
AKASHI Takahiro [Tue, 17 Nov 2020 00:27:16 +0000 (09:27 +0900)]
dfu: simplify the dependencies of DFU_TFTP
Since CONFIG_UPDATE_COMMON always selects CONFIG_DFU_WRITE_ALT, we can
drop the latter from dependencies of CONFIG_DFU_TFTP.
Fixes: 3149e524fc1e ("common: update: add a generic interface for FIT
image") Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org> Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
projects / u-boot.git / log