Neil Armstrong [Thu, 10 Sep 2020 08:48:13 +0000 (10:48 +0200)]
usb: dwc3: add Amlogic GXL & GXL DWC3 Glue
The USB support was initialy done with a set of PHYs and dwc3-of-simple
because the architecture of the USB complex was not understood correctly
at the time (and proper documentation was missing...).
But with the G12A family, the USB complex was correctly understood and
implemented correctly.
This adds a proper driver for the glue, based on the G12A one, but with
enough changes to require a different driver in U-Boot.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Soeren Moch [Thu, 27 Aug 2020 19:52:46 +0000 (21:52 +0200)]
board: tbs2910: Use recommended distroboot addresses
According to doc/README.distro fdt_addr must not be set when DTB is not
available from hardware. So remove this entry.
Use address 32MB above the start of DRAM for kernel_addr_r. This way
we likely can avoid the self-relocation of the compressed kernel image
before it decompresses to offset 0x8000 from start of DRAM.
Use address 128MB above the start of DRAM for fdt_addr_r, since this is
the maximum location for the end of the kernel. So we avoid overwriting
the DTB.
Use 512k above that for ramdisk_addr_r. This should be enough for the
DTB, rest of DRAM can be used for initrd.
Place boot script / extlinux.conf at offset 0 / 1MB from start of DRAM.
This space is available for processing in U-Boot.
Marek Vasut [Thu, 1 Oct 2020 10:25:55 +0000 (12:25 +0200)]
ARM: dts: stm32: Add missing dm-spl props for SPI NOR on AV96
The u-boot,dm-spl DT props are missing on AV96, hence the pinmux and
flash0 nodes are not included in the reduced SPL DT. This prevents
SPI NOR boot from working at all. Fix this by filling them in.
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Patrick Delaunay <patrick.delaunay@st.com> Cc: Patrice Chotard <patrice.chotard@st.com> Reviewed-by: Patrice Chotard <patrice.chotard@st.com> Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
commit 7c8f821e5dde ("i2c: rcar_i2c: Set the slave address from
rcar_i2c_xfer") blindly called rcar_i2c_set_addr() with read argument
always set to 1 during xfer which introduced read/write errors, whereas
earlier rcar_i2c_read_common() called rcar_i2c_set_addr() with read set to
1 and rcar_i2c_write_common() called rcar_i2c_set_addr() with read set 0.
Fixes: 7c8f821e5dde ("i2c: rcar_i2c: Set the slave address from rcar_i2c_xfer") Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com> Reviewed-by: Marek Vasut <marek.vasut+renesas@gmail.com> Reviewed-by: Heiko Schocher <hs@denx.de>
optee: copy FDT OP-TEE related nodes before generic FDT changes
Move call to optee_copy_fdt_nodes() introduced by commit 6ccb05eae01b
before generic changes in kernel FDT so that platform specific changes
are not overridden by the changes made by this function.
Fixes: 6ccb05eae01b ("image: fdt: copy possible optee nodes to a loaded devicetree") Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org> Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
mtd: fix typos in drivers/mtd/Kconfig, drivers/mtd/renesas_rpc_hf.c
Fix a typo
%s/interract/interact/
Use Samsung's capitalization of their trademarks
%s/onenand/OneNAND/
%s/Hyperflash/HyperFlash/
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Reviewed-by: Stefan Roese <sr@denx.de>
[trini: Add other Hyperflash cases as noted by Stefan] Signed-off-by: Tom Rini <trini@konsulko.com>
Peter Robinson [Tue, 29 Sep 2020 09:48:14 +0000 (10:48 +0100)]
Define default CONFIG_PREBOOT with right config option
The 44758771ee commit removes CONFIG_PREBOOT but actually sets the USE_PREBOOT
Kconfig option which isn't CONFIG_PREBOOT and is also a bool option which means
we regress because 'usb start' isn't run when expected, it should also be run
for devices that have USB storage because keyboards aren't the only thing we
might need the USB bus for.
Fixes: 44758771ee ("arm: move CONFIG_PREBOOT="usb start" to KConfig") Signed-off-by: Peter Robinson <pbrobinson@gmail.com> Cc: Jonas Smedegaard <dr@jones.dk> Cc: Neil Armstrong <narmstrong@baylibre.com>
Tom Rini [Mon, 28 Sep 2020 12:26:49 +0000 (08:26 -0400)]
Merge tag 'efi-2020-10-rc6' of https://gitlab.denx.de/u-boot/custodians/u-boot-efi
Pull request for UEFI sub-system for efi-2020-10-rc6
The following UEFI related issues are fixed:
* restore the global data pointer in the RISC-V trap handler
* install EFI_RNG_PROTOCOL only if we have a random number generator
* display human readable string for EFI_RNG_PROTOCOL in efidebug command
riscv: restore global data pointer in trap handler
The gp register is used to store U-Boot's global data pointer. We should
not assume that an UEFI application leaves the gp register unchanged as
the UEFI specifications does not define who is the owner of the gp and tp
registers.
So the following sequence should be followed in the trap handler:
* save the caller's gp register
* restore the global data pointer
* serve interrupts or print crash dump and reset
* restore the caller's gp register
Cc: Abner Chang <abner.chang@hpe.com> Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Reviewed-by: Bin Meng <bin.meng@windriver.com> Reviewed-by: Rick Chen <rick@andestech.com>
Neil Armstrong [Fri, 25 Sep 2020 07:19:20 +0000 (09:19 +0200)]
rng: meson: make core clock optional
This fixes HWRNG support on Amlogic GXL, GXM, G12A, G12B & SM1
based boards dues to the lack of the core clock in the device tree.
It was reported breaking EFI boot in the Linux EFI stub, because the
EFI_RNG_PROTOCOL didn't check for the RNG device presence before
installing itself.
The Linux amlogic,meson-rng.yaml doesn't mandate the core clock,
this the clock should be ignores if not present.
Nevertheless, the clock should be present and this should be fixed
on the Linux meson-gxl.dtsi & meson-g12-common.dtsi then synced
with U-Boot.
The change has been tested on a Khadas VIM3, which uses the common
meson-g12-common.dtsi like the Odroid-C4 & Odroid-N2 in Scott's
report, along with the RNG cmd.
Cc: Heinrich Schuchardt <xypron.glpk@gmx.de> Reported-by: Scott K Logan <logans@cottsay.net> Fixes: bc40eb278b ("drivers/rng: add Amlogic hardware RNG driver") Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Tested-by: Scott K Logan <logans@cottsay.net> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Having an EFI_RNG_PROTOCOL without a backing RNG device leads to failure
to boot Linux 5.8.
Only install the EFI_RNG_PROTOCOL if we have a RNG device.
Reported-by: Scott K Logan <logans@cottsay.net> Cc: Neil Armstrong <narmstrong@baylibre.com> Cc: Ard Biesheuvel <ardb@kernel.org> Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
board: renesas: ebisu: Drop CA57 check in reset_cpu()
Renesas Ebisu board is based on R-Car E3 SoC which has dual CA53 and
a CR7.
This patch drops check for cputype from reset_cpu() and also drops the
corresponding CA57 macros. While at it also dropped RST_RSTOUTCR macro
which is unused.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com> Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
net: pfe_eth: Remove non-DM code check from pfe_spi_flash_init
CONFIG_DM_SPI_FLASH is only supported now with passing of driver
conversion deadline from non-DM to DM model. Hence, it's safe to remove
non-DM code check from pfe_spi_flash_init.
Also use CONFIG_ENV_SPI_MODE and CONFIG_ENV_SPI_MAX_HZ instead of
reading reading values from DT.
All the 10G ports that were working in XFI mode were described as
using XGMII (as PHY_INTERFACE_MODE_XFI was not added at the time).
Add the minimal changes required for the FMan code to support XFI.
drivers: net: ldpaa_eth: lx2160a: fix bug in checking if a DPMAC is enabled
The next DPMAC was always verified if it is enabled. In case of
DPMAC@6, the DPMAC@7 is verified. As DPMAC@7 is disabled, DPMAC@6 will
be considered disabled and not detected by uboot.
Wasim Khan [Thu, 27 Aug 2020 13:43:34 +0000 (19:13 +0530)]
board: freescale: emc2305: Pass chip_addr to set_fan_speed
emc2305 is a common driver. It should not use platform specific
i2c address for slave device.
Pass chip_addr as agrument to emc2305_init() and set_fan_speed()
so that emc2305 driver can be used with different platforms.
Ran Wang [Wed, 5 Aug 2020 07:07:27 +0000 (15:07 +0800)]
fsl-layerscape: enable dwc3 snooping feature
Configure DWC3’s cache type to ‘cacheable’ for better
performance. Actually related register definition and values are SoC
specific, which means this setting is only applicable to Layerscape SoC,
not generic for all platforms which have integrated DWC3 IP.
Signed-off-by: Ran Wang <ran.wang_1@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
arm64: a37xx: pci: Disable link training when unloading driver
As required by PCI Express spec a delay for at least 100ms after
de-asserting PERST# signal is needed before link training is enabled.
Linux kernels prior to 5.8 version do not automatically disable link
training before de-asserting PERST# signal, therefore this requirement is
not fulfilled.
Above requirement is needed for proper detection of some Compex PCIe WiFi
cards. Otherwise Linux kernel cannot detect it.
To allow using those PCIe cards with older Linux kernel versions booted by
U-Boot compiled with U-Boot a37xx pci driver, disable link training in
U-Boot when unloading this pci driver.
Thanks to DM_FLAG_OS_PREPARE flag, U-Boot automatically unload this driver
when booting Linux kernel.
Signed-off-by: Pali Rohár <pali@kernel.org> Reviewed-by: Stefan Roese <sr@denx.de>
Testing on a DNS-325 NAS has shown that in order for the device to work
we need to set CONFIG_NR_DRAM_BANKS to 1 and not 2.
Tested-by: Dmitry N. Kolesnikov <dk.diklab@gmail.com> Reported-by: Dmitry N. Kolesnikov <dk.diklab@gmail.com> Cc: Stefan Herbrechtsmeier <stefan@herbrechtsmeier.net> Signed-off-by: Tom Rini <trini@konsulko.com>
Andre Heider [Fri, 11 Sep 2020 04:35:10 +0000 (06:35 +0200)]
arm: mvebu: Espressobin: Set environment variable fdtfile
Required for the generic distro mechanism.
Linux ships with 4 variants:
marvell/armada-3720-espressobin-v7-emmc.dtb
marvell/armada-3720-espressobin-v7.dtb
marvell/armada-3720-espressobin-emmc.dtb
marvell/armada-3720-espressobin.dtb
Use available information to determine the appropriate filename.
Fixes booting GRUB EFI arm64 on Fedora.
Reported-by: Dennis Gilmore <dennis@ausil.us> Signed-off-by: Andre Heider <a.heider@gmail.com>
Michael Walle [Mon, 3 Aug 2020 22:16:33 +0000 (00:16 +0200)]
pci: layerscape: Fix spurious writes and panic
The fdt_fixup_pcie_ls() scans all PCI devices and assumes that all PCI
root devices are layerscape PCIe controllers. Unfortunately, this is not
true for the LS1028A. There is one additional static PCI root complex
(this contains the networking devices) which has nothing to do with the
layerscape PCIe controllers. On recent U-Boot versions this results in
the following panic:
This bug already existed in former versions, but the spurious write was
never trapped, because the destination address was a valid address (by
pure luck).
Make sure the PCI root is actually one of the expected PCIe layerscape
controllers by matching its compatible string.
Signed-off-by: Michael Walle <michael@walle.cc> Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com> Tested-by: Heiko Thiery <heiko.thiery@gmail.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
scan_dev_for_efi is supposed to be called from scan_dev_for_boot.
However this call is missing for ls1028ardb and ls1028aqds boards. As
a result EFI boot doesn’t work. Fix this issue by removing custom
definition of scan_dev_for_boot and use the default definition
instead.
- fix SPL image generation
- fix incorrect console output
- increase malloc_f and malloc_r space to fix LZMA decompression errors
- increase SPI flash clock
Signed-off-by: Mauro Condarelli <mc5686@mclink.it>
[squashed to one patch, fix commit subject and description] Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
The GPIO bank name for banks J and K are not correct when using the
'gpio' command from the console.
The driver derives the bank name from the device tree instance string by
using the instance value and adding 'A': gpio0@xxaddrxx is Bank A,
gpio1@yyaddryy is Bank B and so on.
On the PIC32, there is no Bank I so instances 8 and 9 need to be
incremented as a minimum change.
An alternative (less opaque) implementation would be to use a bank-name
property instead but this would require modifying the driver code too.
Signed-off-by: John Robertson <john.robertson@simiatec.com>
GPIO state cannot be changed via the device tree (e.g. with gpio-hog) or
using the 'gpio' command from the console.
The root cause is a discrepancy between the driver and the device tree:
the driver code expects an absolute I/O address in the <reg> property,
while the device tree defines the address relative to a declaration in
the parent pinctrl node.
Changing the device tree to fix a driver issue would normally be wrong,
however:
- I have run the first version of U-Boot in which this driver appears
(v2016.03) and the same problem exists, so this is not a regression;
- There is no code that references a parent device tree node that might
suggest the intent of the author was to parse the DT as it exists now;
- The equivalent Linux PIC32 GPIO driver also uses absolute addresses
for the GPIO <reg> property. This change brings the U-Boot DT more
into line with Linux.
Additionally, the data sheet (Microchip ref. 60001361H) shows that the
register set to control a GPIO bank spans 0xE0 bytes, but the device
tree specified size is only 0x48 bytes.
Signed-off-by: John Robertson <john.robertson@simiatec.com>
John Robertson [Tue, 1 Sep 2020 02:55:42 +0000 (02:55 +0000)]
mips: pic32mzdask: disable SDHCI SDCD signal workaround
The PIC32MZ DA Starter Kit does not need the card detect workaround
because the SDCD signal line is connected properly. Disable the
workaround in this case.
Signed-off-by: John Robertson <john.robertson@simiatec.com>
John Robertson [Tue, 1 Sep 2020 02:55:14 +0000 (02:55 +0000)]
mmc: pic32: Refresh PIC32 MMC driver
The existing driver is not compatible with the Driver Model.
This patch makes the necessary changes while also removing obsolescent
calls/properties as follows:
- fdtdec_* calls replaced with dev_read_* equivalents;
- 'clock-freq-min-max' property replaced by querying the frequency of
the source clock 'base_clk';
- The card detect erratum workaround is applied during probe rather than
overriding get_cd.
The card detect workaround (Microchip ref. DS80000736E, erratum #15) is
not always needed and can be disabled using a vendor specific DT
property.
Signed-off-by: John Robertson <john.robertson@simiatec.com>
Chris Packham [Sun, 6 Sep 2020 22:37:35 +0000 (10:37 +1200)]
configs: powerpc: Don't set CONFIG_ENV_ADDR for QorIQ SPIFLASH
Setting CONFIG_ENV_ADDR to something other than 0 stops gd->env_addr
from being allocated dynamically. When the environment is in SPI we need
it to be allocated as we can't use a direct memory mapped address.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Somewhere between v2020.04 and v2020.07 the mpc8xxx_spi driver broke,
I'm guessing due to this hunk
@@ -559,6 +560,8 @@ int dm_gpio_set_dir_flags(struct gpio_desc *desc, ulong flags)
if (ret)
return ret;
+ /* combine the requested flags (for IN/OUT) and the descriptor flags */
+ flags |= desc->flags;
ret = _dm_gpio_set_dir_flags(desc, flags);
from commit 695e5fd5469a ("gpio: update dir_flags management"). But
the blame is mostly on the driver itself which seems rather confused:
The chip select gpios are requested with GPIOD_ACTIVE_LOW, but then in
each activate/deactivate, dm_gpio_set_dir_flags() is called with
merely GPIOD_IS_OUT, and then the driver call set_value(0) for
activate.
That used to work, but with the above hunk, the ACTIVE_LOW setting
from the request becomes persistent, so the gpio driver ends up being
asked to set the value to 1 in mpc8xxx_spi_cs_activate().
So drop the dm_gpio_set_dir_flags() calls in the activate/deactivate
functions, and use a value of 1 to mean "logically enabled".
Ideally, I think we should also drop the GPIOD_ACTIVE_LOW from the
request and make it up to the list of gpio cs in DT to indicate
whether that CS is enabled when driven low (as is of course usually
the case), but that requires changing
arch/powerpc/dts/gdsys/gazerbeam-base.dtsi among others, and I don't
have that hardware to test on. I have, however, tested our
own (mpc8309-based) hardware with this change, and I have also tested
that removing the GPIOD_ACTIVE_LOW from the request and updating our
DT as
Wolfgang Wallner [Wed, 16 Sep 2020 14:57:53 +0000 (16:57 +0200)]
x86: acpi: Add memset to initialize SPCR table
Add a missing memset to acpi_create_spcr().
The other acpi_create_xxxx() functions perform a memset on their
structures, acpi_create_spcr() does not and as a result the contents of
this table are partly uninitialized (and thus random after every reset).
Fixes: b288cd960072 ("x86: acpi: Generate SPCR table") Signed-off-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
[bmeng: fix the tags format in the commit message] Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Wolfgang Wallner [Fri, 11 Sep 2020 14:52:28 +0000 (16:52 +0200)]
x86: fsp: Replace e-mmc with emmc in devicetree bindings
The term eMMC is used inconsistently within the FSP devicetree
bindings (e-mmc and emmc), especially for "emmc-host-max-speed"
documentation and code disagree.
Change all eMMC instances within the FSP bindings to consistently
use "emmc". The term "emmc" is already used a lot within U-Boot,
while "e-mmc" is only used in the FSP bindings.
Signed-off-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
[bmeng: correct one typo in the commit message] Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Fixes: 0b885bcfd9b0 ("acpi: Add an acpi command") Cc: Wolfgang Wallner <wolfgang.wallner@br-automation.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Andy Shevchenko [Tue, 8 Sep 2020 13:57:22 +0000 (16:57 +0300)]
x86: edison: Move config SYS_MALLOC_LEN to Kconfig
This patch moves the the config SYS_MALLOC_LEN to Kconfig
as it is already done for zynq arch in commit 01aa5b8f0503
("Kconfig: Move config SYS_MALLOC_LEN to Kconfig for zynq").
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tom Rini [Sat, 19 Sep 2020 12:31:52 +0000 (08:31 -0400)]
Merge branch '2020-09-18-assorted-bugfixes'
- SquashFS Coverity fixes
- bitflip fix in the alternate memtest command
- Disable networking on bcmstb boards where we didn't have any network
drivers enabled.
Maxim Uvarov [Fri, 28 Aug 2020 19:20:10 +0000 (22:20 +0300)]
efi: change 'env -e -i' usage syntax
'env -e -i' syntax was changed from "," to ":". Account for this also
in the documentation.
Fixes: 2b3fbcb59f41 ("efi_loader: use ':' as separator for setenv -i") Signed-off-by: Maxim Uvarov <maxim.uvarov@linaro.org>
Correct the usage description for setenv -e too. Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Allow specifying the node on which a property is searched.
Test the device tree consistency more rigorously.
Some efi_st_printf() calls have been converted to efi_st_error().
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Ralph Siemsen [Wed, 9 Sep 2020 16:10:00 +0000 (12:10 -0400)]
cmd: mem: fix range of bitflip test
The bitflip test uses two equal sized memory buffers. This is achieved
by splitting the range of memory into two pieces. The address of the
second buffer, as well as the length of each buffer, were not correctly
calculated. This caused bitflip test to access beyond the end of range.
This patch fixes the pointer arithmetic problem.
A second problem arises because u-boot "mtest" command expects the
ending address to be inclusive. When computing (end - start) this
results in missing 1 byte of the requested length. The bitflip test
expects a count rather than an "ending" address. Thus it fails to test
the last word of the requested range. Fixed by using (end - start + 1).
Added Kconfig option to optionally disable the bitflip test, since it
does add significantly to the time taken for "mtest".
Fixes: 8e434cb705d463bc8cff935160e4fb4c77cb99ab ("cmd: mem: Add bitflip
memory test to alternate mtest")
Signed-off-by: Ralph Siemsen <ralph.siemsen@linaro.org> Reviewed-by: Stefan Roese <sr@denx.de>
mmc: fsl_esdhc_imx: check the clock stable status after config the clock rate.
Currently, after config the clock rate, delay 10ms, this is quite a rough
method. Check the clock stable status in the present status register is
enough.
Tested-by: Ji Luo <ji.luo@nxp.com> Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Marek Vasut [Sat, 12 Sep 2020 23:35:08 +0000 (01:35 +0200)]
ARM: mx6: ddr: Add support for iMX6UL/ULL/SL/SDL
This patch adds support for iMX6UL/ULL/SL/SDL MMDC into the DDR calibration
code. The difference between MX6DQ and MX6UL/ULL/SL is that the later SoCs
have 2 SDQS registers, just like MX6SX, while the MX6DQ/MX6SDL has 8.
Fixes: 4f4c128c65 ("ARM: mx6: ddr: Add support for iMX6SX") Signed-off-by: Marek Vasut <marex@denx.de> Cc: Eric Nelson <eric@nelint.com> Cc: Fabio Estevam <fabio.estevam@nxp.com> Cc: Stefano Babic <sbabic@denx.de> Reviewed-by: Fabio Estevam <festevam@gmail.com>
The size of the binary created with the default U-boot config is much
greater than the default offset for environment `0x60000`.
In case if that binary is used for booting via MMC it is overlapped with
the environment stored on MMC.
This leads to U-Boot corruption while saving environment with `saveenv`
command and non-bootable SabreLite board.
The offset for environment `CONFIG_ENV_OFFSET=0x60000` was added in
commit a09fea1 but did not count in the change to `0xC0000` if option
`CONFIG_ENV_IS_IN_MMC` is used.
The offset is also used for variant with environment saving onto SPI NOR
flash (with enabled option `CONFIG_ENV_IS_IN_SPI_FLASH`). In that case the
U-Boot binary flashed on SPI NOR is also corrupted after environment
saving with the original 0x60000 offset.
Signed-off-by: Denis Pynkin <denis.pynkin@collabora.com> Reviewed-by: Tom Rini <trini@konsulko.com>
projects / u-boot.git / log