Michal Simek [Thu, 19 Apr 2018 13:43:50 +0000 (15:43 +0200)]
arm64: zynqmp: Enable cadence WDT for zcu100
Enable watchdog on zcu100 to make sure if there is a bug in the u-boot
there is proper reset.
Watchdog expires and PMU fw is informed and based on setting proper
action is taken.
The patch is enabling reset-on-timeout feature and also fixing fixed
clock rate for watchdog where 100MHz is max (and also default) clock value.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Thu, 19 Apr 2018 13:22:04 +0000 (15:22 +0200)]
watchdog: cadence: Show used timeout value
Debug message was showing timeout value which was passed to start
function but there is a checking if this value can be setup.
The patch is moving this debug printf function below checking.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
nand: zynq: Send address cycles as per onfi parameter page
Send address cycles as per value read from onfi parameter
page for Read and write commands instead of using a
hard coded value. This may vary for different parts and
hence use it from onfi parameter page value.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Fri, 6 Apr 2018 11:32:52 +0000 (13:32 +0200)]
scsi: ceva: Convert driver to use UCLASS_AHCI instead of SCSI
In v2018 the patch
"dm: ahci: Correct uclass private data"
(sha1: bfc1c6b4838501d10aa48c0e92eaf70976f4b2dd)
was causing an issue for ceva_sata.
But this issue is not in v2018.05-rc1 but still converting to
UCLASS_AHCI would make more sense.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch solves assert failed displayed in the console during a boot.
The root cause is that the ubifs_inode is not already allocated when
ubifs_printdir and ubifs_finddir functions are called.
Trace showing the issue:
feed 'boot.scr.uimg', ino 94, new f_pos 0x17b40ece
dent->ch.sqnum '7132', creat_sqnum 3886945402880
UBIFS assert failed in ubifs_finddir at 436
INODE ALLOCATION: creat_sqnum '7129'
Found U-Boot script /boot.scr.uimg
Tom Rini [Tue, 1 May 2018 16:32:37 +0000 (12:32 -0400)]
bootm.c: Correct the flush_len used in bootm_load_os()
In do_bootm_states when doing BOOTM_STATE_LOADOS we use load_end
uninitialized and Coverity notes this now. This however leads down
another interesting path. We pass this pointer to bootm_load_os and
that in turn uses this uninitialized value immediately to calculate the
flush length, and is wrong. We do not know what load_end will be until
after bootm_decomp_image is called, so we must only set flush_len after
that. All of this also makes it clear that the only reason we pass a
pointer for load_end to bootm_load_os is so that we can call lmb_reserve
on success. Rather than initialize load_end to 0 in do_bootm_states we
can just call lmb_reserve ourself.
Reported-by: Coverity (CID: 175572) Cc: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Rini <trini@konsulko.com> Reviewed-by: Simon Glass <sjg@chromium.org>
arm: bitops: fix find_next_zero_bit() for case size < 32
find_next_zero_bit() incorrectly handles cases when:
- total bitmap size < 32
- rest of bits to process
static inline int find_next_zero_bit(void *addr, int size, int offset)
{
unsigned long *p = ((unsigned long *)addr) + (offset >> 5);
unsigned long result = offset & ~31UL;
unsigned long tmp;
if (offset >= size)
return size;
size -= result;
offset &= 31UL;
if (offset) {
tmp = *(p++);
tmp |= ~0UL >> (32-offset);
if (size < 32)
[1]
goto found_first;
if (~tmp)
goto found_middle;
size -= 32;
result += 32;
}
while (size & ~31UL) {
tmp = *(p++);
if (~tmp)
goto found_middle;
result += 32;
size -= 32;
}
[2]
if (!size)
return result;
tmp = *p;
found_first:
[3] tmp |= ~0UL >> size;
^^^ algo can reach above line from from points:
[1] offset > 0 and size < 32, tmp[offset-1..0] bits set to 1
[2] size < 32 - rest of bits to process
in both cases bits to search are tmp[size-1..0], but line [3] will simply
set all tmp[31-size..0] bits to 1 and ffz(tmp) below will fail.
example: bitmap size = 16, offset = 0, bitmap is empty.
code will go through the point [2], tmp = 0x0
after line [3] => tmp = 0xFFFF and ffz(tmp) will return 16.
found_middle:
return result + ffz(tmp);
}
Fix it by correctly seting tmp[31..size] bits to 1 in the above case [3].
Mario Six [Fri, 27 Apr 2018 12:53:37 +0000 (14:53 +0200)]
pci: Don't use pci_indirect when DM is active
Declaration of indirect PCI bridges is not compatible with DM: Both
define PCI operations, but in different ways. Hence, don't use indirect
bridges if DM is active.
Signed-off-by: Mario Six <mario.six@gdsys.cc> Reviewed-by: Simon Glass <sjg@chromium.org>
Ramon Fried [Fri, 20 Apr 2018 19:39:50 +0000 (22:39 +0300)]
db410c: set clk node to be probed before relocation
The clock node is used by the serial driver and it's needed
before relocation.
This patch ensures that the msm-serial driver can actually
use the clock node.
Signed-off-by: Ramon Fried <ramon.fried@linaro.org>
STiH410 has 2 PHYs wired on the DWC3 IP, USB2 and USB3 PHYs.
As currently no U-boot driver is available for the USB3 PHY and to avoid
issue during DWC3 drive probe, we use DWC3 IP with only USB2 PHY
using stih410-b2260-u-boot.dtsi file.
Sam Protsenko [Thu, 19 Apr 2018 20:57:30 +0000 (23:57 +0300)]
arm: ti: boot: Extract PARTS_DEFAULT to boot.h
Eliminate code duplication: the same PARTS_DEFAULT was defined in
am57xx_evm.h and in dra7xx_evm.h. Extract it to environment/boot.h and
use in all OMAP5-based boards.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Neil Armstrong [Mon, 23 Apr 2018 14:19:23 +0000 (16:19 +0200)]
adc: add Amlogic Meson SAR ADC driver
This patch adds the driver for the Amlogic Meson Successive Approximation
Register (SAR) A/D Converter based on the Linux IIO driver thanks to the
great work of Martin Blumenstingl.
The driver has been adapted to U-Boot and the ADC UClass.
This patch depends on the regmap "regmap: add regmap_update_bits() helper"
patch and has been tested using the newly introducted "adc" CLI command
in the "cmd: add ADC cli commands" patch.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Add regulator driver for STM32 voltage reference buffer which can be
used as voltage reference for ADCs, DACs and external components through
dedicated VREF+ pin.
configs: stm32mp15_basic: Set regulator relative flags
Enable DM_REGULATOR_STPMU1 flag to activate regulator
driver for STM32MP15 SoC and CMD_REGULATOR flag to be
able to set/get regulator state int U-boot command line.
Disable PMIC_CHILDREN as this flag is not needed in SPL
for STM32MP1.
Enable support for the regulator functions of the STPMU1X PMIC. The
driver implements get/set api for the various BUCKS and LDOs supported
by the PMIC device. This driver is controlled by a device tree node
which includes voltage limits.
Remove SYS_USE_NANDFLASH, SYS_USE_MMC as they are deprecated and
unused.
The board configurations already use CONFIG_SD_BOOT and
CONFIG_NAND_BOOT respectively.
Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com>
[eugen.hristev@microchip.com: rework on latest u-boot] Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Eugen Hristev [Tue, 24 Apr 2018 09:00:16 +0000 (12:00 +0300)]
configs: at91: sama5: updated mtdparts variable in bootargs
We have a new demo layout of our sama5 boards for the NAND Flash
memory.
According to this new layout, adjust the mtdparts variable in bootargs
to align with this, which is available at :
http://www.at91.com/linux4sam/bin/view/Linux4SAM/Sama5d3XplainedMainPage#NAND_Flash_demo_Memory_map,
Based on original work by Wenyou Yang
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
gpio: atmel_pio4: give a full configuration when muxing pins
When a pin is muxed to a peripheral or as a GPIO, the only
configuration that can be set is the pullup. It is too restrictive
so this patch allows to give a full configuration.
Add PCIe driver for Intel FPGA PCIe IP. This driver operates the PCIe IP in
rootport mode only, the EP mode is not supported. The driver is tested
with the Intel e1000e NIC driver.
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Patrick Bruenn [Wed, 11 Apr 2018 09:16:29 +0000 (11:16 +0200)]
dm: led: add testcase for "default-state" property
Add two more gpio-leds to sandbox test device tree with default-state
property set to "on"/"off".
Add dm_test_led_default_state() to check that these new LED's are set to
LEDST_ON and LEDST_OFF.
dm: led: add testcase for "default-state" property
Add two more gpio-leds to sandbox test device tree with default-state
property set to "on"/"off".
Add dm_test_led_default_state() to check that these new LED's are set to
LEDST_ON and LEDST_OFF.
Signed-off-by: Patrick Bruenn <p.bruenn@beckhoff.com>
Provide an alternate path for sparse-images to be
written to MMC. For example, via tftp on platforms
that don't support fastboot protocol. Or when an
image is to written at some offset, rather than the
start of a partition.
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
[trini: Guard with CONFIG_FASTBOOT_FLASH tests, use LBAF for lbaint_t
printing] Signed-off-by: Tom Rini <trini@konsulko.com>
Patrick Bruenn [Tue, 6 Mar 2018 08:07:23 +0000 (09:07 +0100)]
dm: mmc: socfpga: call dwmci_probe()
On a socfpga_cyclone5 based board the SD card, was never powered up. For
other dw_mmc based SoCs dwmci_probe() is called in the platform specific
probe(). It seems this call is missing for socfpga_dw_mmc.
With this change DWMCI_PWREN is set by dmwci_init().
Signed-off-by: Patrick Bruenn <p.bruenn@beckhoff.com> Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Jaehoon Chung [Fri, 26 Jan 2018 10:25:29 +0000 (19:25 +0900)]
mmc: add the MMC_CLK_ENABLE/DISABLE macro in mmc.h
mmc_set_clock() function has the disable argument as bool type.
When mmc_set_clock is called, it might be passed to "true" or "false".
But it's too confusion whether clock is enabled or disabled with only
"true" and "false".
To prevent the confusion, replace to MMC_CLK_ENABLE/DISABLE macro from
true/false.
Jaehoon Chung [Thu, 25 Jan 2018 07:11:02 +0000 (16:11 +0900)]
power: pmic_max77686: remove the old pmic_max77686 file
max77686 pmic is supporting with max77686.c under pmic/ and regulator/
direnctroy. Remove pmic_max77686.c what didn't use anywhere.
Instead, enable CONFIG_DM_REGULATOR_MAX77686 and
CONFIG_DM_PMIC_MAX77686.
fastboot: sparse: make write_sparse_image useable for non-fastboot
write_sparse_image could be useful for non-fastboot users.
For ex a platform, without usb-device/fastboot support, could
get sparse images over tftp and write using the mmc command.
Or non-android systems could also leverage the sparse format.
Towards that, this patch removes anything fastboot specific from
the write_sparse_image implementation. Which includes making the
function return integer as error code and calls for fastboot logging
via an optional callback function 'mssg'.
The Memory Protection Unit(MPU) allows to partition memory into regions
and set individual protection attributes for each region. In absence
of MPU a default map[1] will take effect. Add support for configuring
MPU on Cortex-R, by reusing the existing support for Cortex-M processor.
Michal Simek [Thu, 26 Apr 2018 12:51:29 +0000 (18:21 +0530)]
arm: v7R: Add initial support
The Cortex-R* processors are a mid-range CPUs for use in deeply-embedded,
real-time systems. It implements the ARMv7-R architecture, and includes
Thumb-2 technology for optimum code density and processing throughput.
Except for MPU(Memory Protection Unit) and few CP15 registers, most of the
features are compatible with v7 architecture. So,reuse the same armv7
folder and introduce a new config CPU_V7R in order to differentiate
from v7 based platforms.
Tested-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Tom Rini <trini@konsulko.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Certain ARM architectures like ARMv7-A, ARMv7-R has support for
enabling caches using CP15 registers. To have a common support
for all these architectures, introduce a Kconfig symbol
SYS_ARM_CACHE_CP15 that selects cache-cp15.c
Tested-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Tom Rini <trini@konsulko.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Add a Kconfig entry for MMU and imply for all platforms using
cache-cp15.c containing MMU setup. Using imply instead of select so that
MMU can be disabled by defconfigs when not needed.
Tested-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Tom Rini <trini@konsulko.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Currently CPU_V7 kconfig symbol supports only ARMv7A architectures under
armv7 folder. This led to a misconception of creating separate folders
for armv7m and armv7r. There is no reason to create separate folder for
other armv7 based architectures when it can co-exist with few Kconfig
symbols.
As a first step towards a common folder, rename CPU_V7 as CPUV7A. Later
separate Kconfig symbols can be added for CPU_V7R and CPU_V7M and
can co exist in the same folder.
Reviewed-by: Tom Rini <trini@konsulko.com> Tested-by: Michal Simek <michal.simek@xilinx.com> Suggested-by: Alexander Graf <agraf@suse.de> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
The syscon implementation in U-Boot is different from that in Linux.
Thus, DT files imported from Linux do not work for U-Boot.
In U-Boot driver model, each node is bound to a dedicated driver
that is the most compatible to it. This design gets along with the
concept of DT, and the syscon in Linux originally worked like that.
However, Linux commit bdb0066df96e ("mfd: syscon: Decouple syscon
interface from platform devices") changed the behavior because it is
useful to let a device bind to another driver, but still work as a
syscon provider.
That change had happened before U-Boot initially supported the syscon
driver by commit 6f98b7504f70 ("dm: Add support for generic system
controllers (syscon)"). So, the U-Boot's syscon works differently
from the beginning. I'd say this is mis-implementation given that
DT is not oriented to a particular project, but Linux is the canon
of DT in practice.
The problem typically arises in the combination of "syscon" and
"simple-mfd" compatibles.
In Linux, they are orthogonal, i.e., the order between "syscon" and
"simple-mfd" does not matter at all.
In U-Boot, this device node is bound to the syscon driver
(driver/core/syscon-uclass.c) since the "syscon" is found to be the
most compatible. Then, syscon_get_regmap() succeeds.
does not work because this node is bound to the simple-bus driver
(drivers/core/simple-bus.c) in favor of "simple-mfd" compatible.
The compatible string "syscon" is just dismissed.
Moreover,
compatible = "foo,bar-syscon", "syscon";
works like the first case because the syscon driver populates the
child devices. This is wrong because populating children is the job
of "simple-mfd" (or "simple-bus").
This commit ports syscon_node_to_regmap() from Linux. This API
does not require the given node to be bound to a driver in any way.
regmap: change regmap_init_mem() to take ofnode instead udevice
Currently, regmap_init_mem() takes a udevice. This requires the node
has already been associated with a device. It prevents syscon/regmap
from behaving like those in Linux.
Change the first argumenet to take a device node.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Acked-by: Neil Armstrong <narmstrong@baylibre.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Putting zero length array at the end of struct is a common technique
to embed arbitrary length of members. There is no good reason to let
regmap_alloc_count() branch by "if (count <= 1)".
As far as I understood the code, regmap->base is an alias of
regmap->ranges[0].start, but it is not helpful but make the code
just ugly.
Rename regmap_alloc_count() to regmap_alloc() because the _count
suffix seems pointless.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Reviewed-by: Simon Glass <sjg@chromium.org>
[trini: fixup cpu_info-rcar.c] Signed-off-by: Tom Rini <trini@konsulko.com>
projects / u-boot.git / log