Marc Jones [Mon, 29 Oct 2012 05:24:02 +0000 (05:24 +0000)]
ahci: Perform SATA flush after disk write.
Writes in u-boot are so rare, and the logic to know when is
the last write and do a flush only there is sufficiently
difficult. Just do a flush after every write. This incurs,
usually, one extra flush when the rare writes do happen.
Signed-off-by: Marc Jones <marc.jones@chromium.org> Signed-off-by: Simon Glass <sjg@chromium.org>
Walter Murphy [Mon, 29 Oct 2012 05:24:00 +0000 (05:24 +0000)]
ahci: Adjust SATA timeouts for hard disk (spinup delay & command timeout)
Note: These are timeout values and not delay values, so the event being
timed out will complete whenever it is actually ready, with a
measurement granularity of 1 millisecond, up till the timeout value.
Therefore, there is no effect on SSD booting.
The values were determined by instrumenting the code and measuring the
actual time taken by several different models of HDD for each of the
parameters and then adding 50% more for the spinup value and just
doubling the command timeout value.
Signed-off-by: Walter Murphy <wmurphy@chromium.org> Signed-off-by: Simon Glass <sjg@chromium.org>
Taylor Hutt [Mon, 29 Oct 2012 05:23:59 +0000 (05:23 +0000)]
ahci: flush / invalidate dcache around SATA commands
Exynos5 automatically performs DMA when the SATA controller executes
commands. This adds the necessary dcache-to-memory flush &
invalidation calls to allow the DMA to properly function.
Signed-off-by: Taylor Hutt <thutt@chromium.org> Signed-off-by: Simon Glass <sjg@chromium.org>
Taylor Hutt [Mon, 29 Oct 2012 05:23:58 +0000 (05:23 +0000)]
ahci: Use virt_to_phys() to denote physical addresses for DMA
Update the assignment of various physical memory buffers used by the
SATA controller to explicitly be denoted as physical addresses.
The memory is identity-mapped, so these function calls are a nop, but
they provide good semantic documentation for any maintainers.
The return value of virt_to_phys() is 'unsigned long'. On machines
where sizeof(unsigned long) != sizeof(pointer), a cast through
(uintptr_t) is needed to appease the compiler due to the potential of
losing the upper 32 bits of the address.
In compilation this scenario, a physical address could be 64-bits, yet
the C pointer environment only allows 32-bit addresses; the constraint
is that pointers cannot address more than 4Gb of memory and if
virt_to_phys() ever returns an out-of-range value for the physical
address, there are issues with emmory mapping which must be solved.
However, since the memory is identify mappeed, there is no problem
introducing the cast: the original pointer will reside in 32-bits, so
the physical address will also be within in 32-bits.
Signed-off-by: Taylor Hutt <thutt@chromium.org> Signed-off-by: Simon Glass <sjg@chromium.org>
Gabe Black [Mon, 29 Oct 2012 05:23:54 +0000 (05:23 +0000)]
ahci: Make the AHCI code find the capacity of disks > 128 GB properly
In the structure returned by the ATA identify device command, there are two
fields which describe the device capacity. One is a 32 bit data type which
reports the number of sectors as a 28 bit LBA, and the other is a 64 bit data
type which is for a 48 bit LBA. If the device doesn't support 48 bit LBAs,
the small value is the only value with the correct size. If it supports more,
if the number of sectors is small enough to fit into 28 bits, both fields
reflect the correct value. If it's too large, the smaller field has 28 bits of
1s, 0xfffffff, and the other field has the correct value.
The AHCI driver is implemented by attaching to the generic SCSI code and
translating on the fly between SCSI binary data structures and AHCI data
structures. It responds to requests to execute specific SCSI commands by
executing the equivalent AHCI commands and then crafting a response which
matches what a SCSI disk would send.
The AHCI driver now considers both fields and chooses the correct one when
implementing both the SCSI READ CAPACITY (10) and READ CAPACITY (16) commands.
Signed-off-by: Gabe Black <gabeblack@chromium.org> Signed-off-by: Simon Glass <sjg@chromium.org>
Hung-Te Lin [Mon, 29 Oct 2012 05:23:53 +0000 (05:23 +0000)]
ahci: support scsi writing in AHCI driver
The "scsi write" command requires support from underlying driver.
This CL enables SCSI_WRITE10 in AHCI driver.
Tested in U-Boot console, try to i/o with sector #64:
scsi read 1000 40 1
md.b 1000 200 # check if things are not 0xcc
mw.b 1000 cc 200 # try to fill with 0xcc
scsi write 1000 40 1
mw.b 1000 0 200 # fill with zero
md.b 1000 200 # should be all 0
scsi read 1000 40 1
md.b 1000 200 # should be all 0xcc
Signed-off-by: Hung-Te Lin <hungte@chromium.org> Signed-off-by: Simon Glass <sjg@chromium.org>
Gabe Black [Mon, 29 Oct 2012 05:23:52 +0000 (05:23 +0000)]
ahci: Make sending the SETFEATURES_XFER command optional
This command doesn't really do anything when talking to a SATA device, and
sending it confuses some of them. This change makes sending the command
optional, and defaults to not. The situations where it should be sent are not
the common case.
With the standard SSD in the machine, here are some times with the option
turned off:
1. 8277
2. 8273
3. 8050
And turned on:
1. 8303
2. 8155
3. 8276
Sending that command seems to have no meaningful effect on performance.
This fixes problems with an SSD marked Toshiba NV6424, Taiwan 11159AE P
and TC58NVG5D2FTA10.
Signed-off-by: Gabe Black <gabeblack@chromium.org> Signed-off-by: Taylor Hutt <thutt@chromium.org> Signed-off-by: Simon Glass <sjg@chromium.org>
Stefan Reinauer [Mon, 29 Oct 2012 05:23:51 +0000 (05:23 +0000)]
ahci: cosmetics and cleanup
- print the correct speed
- print all the AHCI capability flags
(information taken from Linux kernel driver)
- clean up some comments
For example, this might show the following string:
AHCI 0001.0300 32 slots 6 ports 6 Gbps 0x3 impl SATA mode
Signed-off-by: Stefan Reinauer <reinauer@chromium.org>
Commit-Ready: Stefan Reinauer <reinauer@chromium.org> Signed-off-by: Simon Glass <sjg@chromium.org> Tested-by: Stefan Reinauer <reinauer@chromium.org>
Stefan Reinauer [Mon, 29 Oct 2012 05:23:49 +0000 (05:23 +0000)]
ahci: Optimise AHCI controller reset and start-up
The existing code waits a whole second for the AHCI controller to reset.
Instead, let's poll the status register to see if the reset has
succeeded and return earlier if possible. This brings down the time for
AHCI probing from 1s to 20ms.
Signed-off-by: Stefan Reinauer <reinauer@chromium.org> Signed-off-by: Simon Glass <sjg@chromium.org>
Vadim Bendebury [Mon, 29 Oct 2012 05:23:45 +0000 (05:23 +0000)]
scsi: Provide support for a list of AHCI controllers.
Many AHCI controllers are identical, the main (and often the
only) difference being the PCI Vendor ID/Device ID combination
reported by the device.
This change allows the config file to define a list of PCI vendor
ID/device ID pairs. The driver would scan the list and initialize
the first device it finds.
No actual multiple device list is introduced yet, this change
just add the framework.
Signed-off-by: Vadim Bendebury <vbendeb@chromium.org> Signed-off-by: Taylor Hutt <thutt@chromium.org> Signed-off-by: Simon Glass <sjg@chromium.org>
Vadim Bendebury [Mon, 29 Oct 2012 05:23:44 +0000 (05:23 +0000)]
ahci: Support splitting of read transactions into multiple chunks
With an Intel AHCI controller, the driver does not operate properly
if the requested amount of blocks to read exceeds 255.
It is probably possible to specify 0 as the block count and the driver
will read 256 blocks, but it was decided to limit the number of blocks
read at once to 128 (it should be a power of 2 for the optimal
performance of solid state drives).
Signed-off-by: Vadim Bendebury <vbendeb@chromium.org> Signed-off-by: Simon Glass <sjg@chromium.org>
Stefan Roese [Fri, 26 Oct 2012 04:24:01 +0000 (04:24 +0000)]
ZFS: Fix compile warning in fs/zfs/zfs.c (GCC 4.6.4 from ELDK 5.2.1)
This patch fixes the following compile warning:
zfs.c:2006:1: warning: 'zfs_label' defined but not used [-Wunused-function]
zfs.c:2029:1: warning: 'zfs_uuid' defined but not used [-Wunused-function]
Signed-off-by: Stefan Roese <sr@denx.de> Cc: Jorgen Lundman <lundman@lundman.net>
Stefan Roese [Fri, 26 Oct 2012 04:24:00 +0000 (04:24 +0000)]
ZFS: Fix compile warning in cmd_zfs.c (GCC 4.6.4 from ELDK 5.2.1)
This patch fixes the following compile warnings:
cmd_zfs.c:177:1: warning: initialization from incompatible pointer type [enabled by default]
cmd_zfs.c:177:1: warning: (near initialization for '_u_boot_list_cmd_zfsls.cmd') [enabled by default]
cmd_zfs.c:182:1: warning: initialization from incompatible pointer type [enabled by default]
cmd_zfs.c:182:1: warning: (near initialization for '_u_boot_list_cmd_zfsload.cmd') [enabled by default]
Signed-off-by: Stefan Roese <sr@denx.de> Cc: Jorgen Lundman <lundman@lundman.net>
Tom Rini [Wed, 24 Oct 2012 07:28:17 +0000 (07:28 +0000)]
am335x_evm: Add CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG support
We add CONFIG_ENV_VARS_UBOOT_CONFIG,
CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG and CONFIG_BOARD_LATE_INIT to set
the variables and then fdtfile and findfdt to make us of this. It is
now possible to do 'run findfdt' to have fdtfile be set to the value of
the dtb file to load for the board we are running on.
Stephen Warren [Wed, 31 Oct 2012 11:17:28 +0000 (11:17 +0000)]
Add board_name to CONFIG_ENV_VARS_UBOOT_CONFIG
CONFIG_ENV_VARS_UBOOT_CONFIG creates environment variables indicating
which configuration U-Boot was built for. Some U-Boot binaries run on
multiple boards, and hence this information may not uniquley describe
the HW that U-Boot is actually running on. Another patch introduces
environment variable board_name to represent that. In order to avoid
scripts having to check $board_name, use it if set, and then fall back
to using $board, make CONFIG_ENV_VARS_UBOOT_CONFIG also set a default
value for board_name, so that variable is always available.
Signed-off-by: Stephen Warren <swarren@nvidia.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This option is intended to be set by boards which will set the
board_name and board_rev environment variables. These are to be used
when the U-Boot binary can support more than one board type at run-time
and the user needs an easy way (for example for scripting to determine
what device tree to load) to determine what board they are on.
Wolfgang Denk [Tue, 30 Oct 2012 09:19:52 +0000 (09:19 +0000)]
lib/vsprintf.c: don't special-case pointers to address null
The %p format of printf() would print a pointer to address null as
"(null)". This makes sense in a real OS where a NULL pointer must
never be dereferenced, but this is a bootloader, and there are cases
where accessing the data at address null makes perfect sense.
Remove the special case in lib/vsprintf.c using "#if 0" with a comment
to make clear this was an intentional change and to stop re-adding
this code.
Signed-off-by: Wolfgang Denk <wd@denx.de> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Tom Rini [Mon, 29 Oct 2012 14:53:18 +0000 (14:53 +0000)]
cmd_fdt.c: Use %p when printing pointers
When putting pointers into a format string use %p to ensure that they
are printed correctly regardless of bitsize. This fixes warnings on
sandbox on 64bit systems.
Cc: Joe Hershberger <joe.hershberger@ni.com> Cc: Gerald Van Baren <vanbaren@cideas.com> Signed-off-by: Tom Rini <trini@ti.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Tom Rini [Thu, 25 Oct 2012 08:53:14 +0000 (08:53 +0000)]
MAKEALL: Add -s to '${MAKE} tidy' section
When BUILD_NBUILDS is > 1 we run the tidy command. With the addition of
DocBook this now includes a -C doc/DocBook and a 'entering/leaving' pair
of messages happen. Since we don't want to see what's being cleaned
here, we can just invoke make -s like we do when building.
Stephen Warren [Mon, 22 Oct 2012 06:43:51 +0000 (06:43 +0000)]
fs: add filesystem switch libary, implement ls and fsload commands
Implement "ls" and "fsload" commands that act like {fat,ext2}{ls,load},
and transparently handle either file-system. This scheme could easily be
extended to other filesystem types; I only didn't do it for zfs because
I don't have any filesystems of that type to test with.
Replace the implementation of {fat,ext[24]}{ls,load} with this new code
too.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Stephen Warren [Mon, 22 Oct 2012 06:43:50 +0000 (06:43 +0000)]
fs: separate CONFIG_FS_{FAT, EXT4} from CONFIG_CMD_{FAT, EXT*}
This makes the FAT and ext4 filesystem implementations build if
CONFIG_FS_{FAT,EXT4} are defined, rather than basing the build on
whether CONFIG_CMD_{FAT,EXT*} are defined. This will allow the
filesystems to be built separately from the filesystem-specific commands
that use them. This paves the way for the creation of filesystem-generic
commands that used the filesystems, without requiring the filesystem-
specific commands.
Minor documentation changes are made for this change.
The new config options are automatically selected by the old config
options to retain backwards-compatibility.
Signed-off-by: Stephen Warren <swarren@nvidia.com> Reviewed-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Stephen Warren [Mon, 22 Oct 2012 06:43:49 +0000 (06:43 +0000)]
fs: delete unused Makefile
fs/Makefile is unused. The top-level Makefile sets LIBS-y += fs/xxx and
hence causes make to directly descend two directory levels into each
individual filesystem, and it never descends into fs/ itself.
So, delete this useless file.
Signed-off-by: Stephen Warren <swarren@nvidia.com> Reviewed-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com> Acked-by: Simon Glass <sjg@chromium.org>
The command declaration now uses the new LG-array method to generate
list of commands. Thus the __u_boot_cmd section is now superseded and
redundant and therefore can be removed. Also, remove externed symbols
associated with this section from include/command.h .
Signed-off-by: Jason Jin <Jason.jin@freescale.com>
Stephen Warren [Mon, 22 Oct 2012 06:19:32 +0000 (06:19 +0000)]
ARM: fix u-boot.lds for -ffunction-sections/-fdata-sections
When -ffunction-sections or -fdata-section are used, symbols are placed
into sections such as .data.eserial1_device and .bss.serial_current.
Update the linker script to explicitly include these. Without this
change (at least with my gcc-4.5.3 built using crosstool-ng), I see that
the sections do end up being included, but __bss_end__ gets set to the
same value as __bss_start.
Signed-off-by: Stephen Warren <swarren@nvidia.com> Acked-by: Allen Martin <amartin@nvidia.com> Acked-by: Simon Glass <sjg@chromium.org> Tested-by: Simon Glass <sjg@chromium.org>
Albert ARIBAUD [Thu, 18 Oct 2012 10:15:45 +0000 (10:15 +0000)]
arm: arm925t: remove SX1 board
SX1 does not build properly by itself, is not built
as part of MAKEALL arm or MAKEALL -a arm, and is only
present in Makefile, not boards.cfg. As it also has no
entry in MAINTAINERS, it is orphan and non-functional.
Remove it.
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
Allen Martin [Thu, 25 Oct 2012 13:30:14 +0000 (13:30 +0000)]
serial: remove calls to serial_assign()
Remove calls to serial_assign() that are failing now that it returns a
proper error code. This calls were not actually doing anything
because they passed the name of a stdio_dev when a serial_device name
is exptectd.
Signed-off-by: Allen Martin <amartin@nvidia.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> Acked-by: Marek Vasut <marex@denx.de> Acked-by: Simon Glass <sjg@chromium.org> Tested-by: Simon Glass <sjg@chromium.org> Tested-by: Stephen Warren <swarren@nvidia.com>
This makes the FAT filesystem API more consistent with other block-based
filesystems. If in the future standard multi-filesystem commands such as
"ls" or "load" are implemented, having FAT work the same way as other
filesystems will be necessary.
Convert cmd_fat.c to the new API, so the code looks more like other files
implementing the same commands for other filesystems.
Signed-off-by: Stephen Warren <swarren@nvidia.com> Reviewed-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Stephen Warren [Wed, 17 Oct 2012 06:44:57 +0000 (06:44 +0000)]
FAT: remove cur_part_nr
A future patch will implement the more standard filesystem API
fat_set_blk_dev(). This API has no way to know which partition number
the partition represents. Equally, future DM rework will make the
concept of partition number harder to pass around.
So, simply remove cur_part_nr from fat.c; its only use is in a
diagnostic printf, and the context where it's printed should make it
obvious which partition is referred to anyway (since the partition ID
would come from the user command-line that caused it).
Signed-off-by: Stephen Warren <swarren@nvidia.com> Reviewed-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Kim Phillips [Tue, 16 Oct 2012 14:28:48 +0000 (14:28 +0000)]
drivers/serial/serial_ns16550.c: sparse fixes
serial_ns16550.c:222:1: warning: symbol 'eserial1_init' was not declared. Should it be static?
serial_ns16550.c:222:1: warning: symbol 'eserial1_setbrg' was not declared. Should it be static?
serial_ns16550.c:222:1: warning: symbol 'eserial1_getc' was not declared. Should it be static?
serial_ns16550.c:222:1: warning: symbol 'eserial1_tstc' was not declared. Should it be static?
serial_ns16550.c:222:1: warning: symbol 'eserial1_putc' was not declared. Should it be static?
serial_ns16550.c:222:1: warning: symbol 'eserial1_puts' was not declared. Should it be static?
serial_ns16550.c:225:1: warning: symbol 'eserial2_init' was not declared. Should it be static?
serial_ns16550.c:225:1: warning: symbol 'eserial2_setbrg' was not declared. Should it be static?
serial_ns16550.c:225:1: warning: symbol 'eserial2_getc' was not declared. Should it be static?
serial_ns16550.c:225:1: warning: symbol 'eserial2_tstc' was not declared. Should it be static?
serial_ns16550.c:225:1: warning: symbol 'eserial2_putc' was not declared. Should it be static?
serial_ns16550.c:225:1: warning: symbol 'eserial2_puts' was not declared. Should it be static?
serial_ns16550.c:228:1: warning: symbol 'eserial3_init' was not declared. Should it be static?
serial_ns16550.c:228:1: warning: symbol 'eserial3_setbrg' was not declared. Should it be static?
serial_ns16550.c:228:1: warning: symbol 'eserial3_getc' was not declared. Should it be static?
serial_ns16550.c:228:1: warning: symbol 'eserial3_tstc' was not declared. Should it be static?
serial_ns16550.c:228:1: warning: symbol 'eserial3_putc' was not declared. Should it be static?
serial_ns16550.c:228:1: warning: symbol 'eserial3_puts' was not declared. Should it be static?
serial_ns16550.c:231:1: warning: symbol 'eserial4_init' was not declared. Should it be static?
serial_ns16550.c:231:1: warning: symbol 'eserial4_setbrg' was not declared. Should it be static?
serial_ns16550.c:231:1: warning: symbol 'eserial4_getc' was not declared. Should it be static?
serial_ns16550.c:231:1: warning: symbol 'eserial4_tstc' was not declared. Should it be static?
serial_ns16550.c:231:1: warning: symbol 'eserial4_putc' was not declared. Should it be static?
serial_ns16550.c:231:1: warning: symbol 'eserial4_puts' was not declared. Should it be static?
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
In order to support low power state, you must source kernel system
timers to persistent clock, available across suspend/resume. In case of
AM335x device, the only source we have is, RTC32K, available in
wakeup/always-on domain. Having said that, during validation it has
been observed that, RTC clock need couple of seconds delay to stabilize
the RTC OSC clock; and such a huge delay is not acceptable in kernel
especially during early init and also it will impact quick/fast boot
use-cases.
So, RTC32k OSC enable dependency has been shifted to
SPL/first-bootloader.
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com> Signed-off-by: Tom Rini <trini@ti.com>
Alison Wang [Thu, 18 Oct 2012 19:25:51 +0000 (19:25 +0000)]
ColdFire: Add MCF5441x CPU support
Add MCF5441x CPU support.
The MCF5441x devices are a family of highly-integrated 32-bit
microprocessors based on the Version 4m ColdFire microarchitecture,
comprising of the V4 integer core, memory management unit(MMU) and
enchanced multiply-accumulate unit(EMAC).
Signed-off-by: TsiChung Liew <tsicliew@gmail.com> Signed-off-by: Jason Jin <Jason.jin@freescale.com> Signed-off-by: Alison Wang <b18965@freescale.com>
Gerlando Falauto [Wed, 10 Oct 2012 22:13:10 +0000 (22:13 +0000)]
km83xx: add kmvect1 board
Add support for the new kmvect1 board powered by the mpc8309 processor.
As this board is very similar to the existing suvd3, instead of adding a
new config header file, just add a new config option to suvd3.h
Signed-off-by: Gerlando Falauto <gerlando.falauto@keymile.com> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Gerlando Falauto [Wed, 10 Oct 2012 22:13:09 +0000 (22:13 +0000)]
km83xx: add common support for km8309 boards
Add support for Keymile boards based on mpc8309
(it would be only kmvect1 for now)
Signed-off-by: Gerlando Falauto <gerlando.falauto@keymile.com>
[#elseif -> #if to allow kmcoge5ne and kmeter1 to build successfully] Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Gerlando Falauto [Wed, 10 Oct 2012 22:13:08 +0000 (22:13 +0000)]
mpc83xx: add support for mpc8309
This processor, though very similar to other members of the
PowerQUICC II Pro family (namely 8308, 8360 and 832x), provides
yet another feature set than any supported sibling.
Signed-off-by: Gerlando Falauto <gerlando.falauto@keymile.com> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Gerlando Falauto [Wed, 10 Oct 2012 22:13:07 +0000 (22:13 +0000)]
cleanup: introduce CONFIG_MPC830x
Introduce a new configuration token CONFIG_MPC830x to be shared among
mpc8308 and mpc8309. Define it for existing 8308 boards, and refactor
existing common code so to make future introduction of 8309 simpler.
Signed-off-by: Gerlando Falauto <gerlando.falauto@keymile.com> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Andrew Bradford [Mon, 1 Oct 2012 05:06:52 +0000 (05:06 +0000)]
configs: Fix usage of mmc rescan
Fix usage of 'mmc rescan' by many configs. Proper use is
'mmc dev ${mmcdev}; mmc rescan' to set the mmc device and then rescan
the device. 'mmc rescan' itself does not take any arguments.
Signed-off-by: Andrew Bradford <andrew@bradfordembedded.com>
Joel A Fernandes [Tue, 25 Sep 2012 06:49:47 +0000 (06:49 +0000)]
am33xx: Enable DDR3 for DDR3 version of beaglebone
DDR3 support is tested and working with beaglebone hardware. Include a check
for this board type and configure DDR3. The timings and other configuration
match EVM SK.
Signed-off-by: Joel A Fernandes <joelagnel@ti.com> Acked-by: Jason Kridner <jdk@ti.com>
USB: musb_udc: Make musb_peri_rx_ep check for MUSB_RXCSR_RXPKTRDY
The endpoint rx count register value will be zero if it is read before
receive packet ready bit (PERI_RXCSR:RXPKTRDY) is set.
Check for the receive packet ready bit (PERI_RXCSR:RXPKTRDY) before
reading endpoint rx count register. Proceed with rx count read and
FIFO read only if RXPKTRDY bit is set.
Signed-off-by: Pankaj Bharadiya <pankaj.bharadiya@ti.com> Signed-off-by: Tom Rini <trini@ti.com>
Andy Fleming [Mon, 22 Oct 2012 22:28:18 +0000 (17:28 -0500)]
85xx: Protect timeout_save variable with ifdefs
The timeout_save variable was only used by the DDR111_134
erratum code. It was being set, but never used. Newer compilers
will actually complain about this.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Liu Gang [Sun, 14 Oct 2012 20:55:17 +0000 (20:55 +0000)]
powerpc/boot: Change the compile macro for SRIO & PCIE boot master module
Currently, the SRIO and PCIE boot master module will be compiled into the
u-boot image if the macro "CONFIG_FSL_CORENET" has been defined. And this
macro has been included by all the corenet architecture platform boards.
But in fact, it's uncertain whether all corenet platform boards support
this feature.
So it may be better to get rid of the macro "CONFIG_FSL_CORENET", and add
a special macro for every board which can support the feature. This
special macro will be defined in the header file
"arch/powerpc/include/asm/config_mpc85xx.h". It will decide if the SRIO
and PCIE boot master module should be compiled into the board u-boot image.
Signed-off-by: Liu Gang <Gang.Liu@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
Shaohui Xie [Thu, 11 Oct 2012 20:31:46 +0000 (20:31 +0000)]
powerpc/espi: remove write command length check
Current espi controller driver assumes the command length of write command is
not equal to '1', it was made based on SPANSION SPI flash, but some SPI flash
driver such as SST does use write command length as '1', so write command on
SST SPI flash will not work. And the length check for write command is not
necessary for SPANSION, though it's harmless for SPANSION, it will stop write
operation on flashes like SST, so we remove the check.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
shaohui xie [Thu, 11 Oct 2012 20:25:36 +0000 (20:25 +0000)]
powerpc/fm: fix TBI PHY address settings
TBI PHY address (TBIPA) register is set in general frame manager
phy init funciton dtsec_init_phy() in drivers/net/fm/eth.c, and
it is supposed to set TBIPA on FM1@DTSEC1 in case of FM1@DTSEC1
isn't used directly, which provides MDIO for other ports. So
following code is wrong in case of FM2, which has a different
mac base.
struct dtsec *regs = (struct dtsec *)fm_eth->mac->base;
/* Assign a Physical address to the TBI */
out_be32(®s->tbipa, CONFIG_SYS_TBIPA_VALUE);
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
Haiying Wang [Thu, 11 Oct 2012 07:13:38 +0000 (07:13 +0000)]
mpc85xx/portals: Add qman and bman ip_cfg field into portal info
Because QMan3.0 and BMan2.1 used ip_cfg in ip_rev_2 register to differ the
total portal number, buffer pool number etc, we can use this info to limit
those resources in kernel driver.
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
York Sun [Thu, 11 Oct 2012 07:13:37 +0000 (07:13 +0000)]
powerpc/t4qds: Add T4QDS board
The T4240QDS is a high-performance computing evaluation, development and
test platform supporting the T4240 QorIQ Power Architecture™ processor.
SERDES Connections
32 lanes grouped into four 8-lane banks
Two “front side” banks dedicated to Ethernet
Two “back side” banks dedicated to other protocols
DDR Controllers
Three independant 64-bit DDR3 controllers
Supports rates up to 2133 MHz data-rate
Supports two DDR3/DDR3LP UDIMM/RDIMMs per controller
QIXIS System Logic FPGA
Each DDR controller has two DIMM slots. The first slot of each controller
has up to 4 chip selects to support single-, dual- and quad-rank DIMMs.
The second slot has only 2 chip selects to support single- and dual-rank
DIMMs. At any given time, up to total 4 chip selects can be used.
Detail information can be found in doc/README.t4qds
Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org> Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com> Signed-off-by: Roy Zang <tie-fei.zang@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
York Sun [Mon, 8 Oct 2012 07:44:31 +0000 (07:44 +0000)]
powerpc/mpc85xx: Add CONFIG_DDR_CLK_FREQ for corenet platform
New corenet platforms with chassis2 have separated DDR clock inputs. Use
CONFIG_DDR_CLK_FREQ for DDR clock. This patch also cleans up the logic of
detecting and displaying synchronous vs asynchronous mode.
Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
projects / u-boot.git / log