git.dujemihanovic.xyz Git - u-boot.git/log

net: phy: Synchronize PHY interface modes with Linux

Synchronize PHY interface modes with Linux next 6.2.y commit:
0194b64578e90 ("net: phy: improve phy_read_poll_timeout")

Retain LX2160A/LX2162A PHY modes as those are not yet supported
by the Linux kernel, but isolate those with ifdeffery.

Isolate NCSI which are also not supported by Linux kernel. Note
that the ifdeffery cannot be avoided with IS_ENABLED() here due
to compilation of the entire conditional, which would fail in
case NCSI symbols are not available.

Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>

net: mvpp2: Replace PHY_INTERFACE_MODE_SFI with 5GBASER/10GBASER/XAUI

Replace PHY_INTERFACE_MODE_SFI with PHY_INTERFACE_MODE_5GBASER,
PHY_INTERFACE_MODE_10GBASER and PHY_INTERFACE_MODE_XAUI to match
Linux PHY interface modes.

Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>

net: mvpp2: Drop PHY_INTERFACE_MODE_SGMII_2500 support

This mode does not seem to be well defined and used anywhere, remove support for it.
Based on discussion:
- 1000baseX does c37 AN of duplex+pause
- SGMII does AN of duplex+pause+speed, at lower speed bytes are repeated 10x/100x
- 2500baseX does not do AN, or does very different c73 AN
- SGMII 2500 behavior is unclear

Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>

net: phy: Only call phy_init() on systems needing manual relocation

The phy_init() is now used only to perform manual relocation of PHY
driver callbacks. Wrap it in ifdeffery and only call it on systems
which still require manual relocation, i.e. m68k .

Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Acked-by: Michal Simek <michal.simek@amd.com>
Tested-by: Michal Simek <michal.simek@amd.com> #microblaze (MANUAL_RELOC)

net: phy: Re-inline phy_drv_reloc()

Wrap phy_drv_reloc() back into phy_init() to reduce ifdeffery,
since phy_drv_reloc() is now called only from one call site.
No functional change.

Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Acked-by: Michal Simek <michal.simek@amd.com>
Tested-by: Michal Simek <michal.simek@amd.com> #microblaze (MANUAL_RELOC)

net: phy: Drop unused phy_register()

This function is no longer used, drop it.

Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Acked-by: Michal Simek <michal.simek@amd.com>
Tested-by: Michal Simek <michal.simek@amd.com> #microblaze (MANUAL_RELOC)

net: phy: Drop static phy_drivers list

The static phy_drivers list is superseded by linker list of struct phy_drivers
now that all drivers have been converted to the later. Drop the phy_drivers
list as well as list_head from struct phy_driver.

Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Acked-by: Michal Simek <michal.simek@amd.com>
Tested-by: Michal Simek <michal.simek@amd.com> #microblaze (MANUAL_RELOC)

net: phy: gen10g: Convert to U_BOOT_PHY_DRIVER()

Convert PHY driver to U_BOOT_PHY_DRIVER() macro and drop phy_register() init call.

Converted using sed
"s@^static struct phy_driver $.*$_driver = \+{@U_BOOT_PHY_DRIVER(\L\1) = {"

Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Acked-by: Michal Simek <michal.simek@amd.com>
Tested-by: Michal Simek <michal.simek@amd.com> #microblaze (MANUAL_RELOC)

net: phy: genphy: Convert to U_BOOT_PHY_DRIVER()

Convert PHY driver to U_BOOT_PHY_DRIVER() macro and drop phy_register() init call.

Converted using sed
"s@^static struct phy_driver $.*$_driver = \+{@U_BOOT_PHY_DRIVER(\L\1) = {"

Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Acked-by: Michal Simek <michal.simek@amd.com>
Tested-by: Michal Simek <michal.simek@amd.com> #microblaze (MANUAL_RELOC)

net: phy: xilinx-gmii2rgmii: Convert to U_BOOT_PHY_DRIVER()

Convert PHY driver to U_BOOT_PHY_DRIVER() macro and drop phy_register() init call.

Converted using sed
"s@^static struct phy_driver $.*$_driver = \+{@U_BOOT_PHY_DRIVER(\L\1) = {"

Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Acked-by: Michal Simek <michal.simek@amd.com>
Tested-by: Michal Simek <michal.simek@amd.com> #microblaze (MANUAL_RELOC)

net: phy: ncsi: Convert to U_BOOT_PHY_DRIVER()

Convert PHY driver to U_BOOT_PHY_DRIVER() macro and drop phy_register() init call.

Converted using sed
"s@^static struct phy_driver $.*$_driver = \+{@U_BOOT_PHY_DRIVER(\L\1) = {"

Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Acked-by: Michal Simek <michal.simek@amd.com>
Tested-by: Michal Simek <michal.simek@amd.com> #microblaze (MANUAL_RELOC)

net: phy: fixed: Convert to U_BOOT_PHY_DRIVER()

Convert PHY driver to U_BOOT_PHY_DRIVER() macro and drop phy_register() init call.

Converted using sed
"s@^static struct phy_driver $.*$_driver = \+{@U_BOOT_PHY_DRIVER(\L\1) = {"

Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Acked-by: Michal Simek <michal.simek@amd.com>
Tested-by: Michal Simek <michal.simek@amd.com> #microblaze (MANUAL_RELOC)

net: phy: mscc: Convert to U_BOOT_PHY_DRIVER()

Convert PHY driver to U_BOOT_PHY_DRIVER() macro and drop phy_register() init call.

Converted using sed
"s@^static struct phy_driver $.*$_driver = \+{@U_BOOT_PHY_DRIVER(\L\1) = {"

Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Acked-by: Michal Simek <michal.simek@amd.com>
Tested-by: Michal Simek <michal.simek@amd.com> #microblaze (MANUAL_RELOC)

net: phy: intel-xway: Convert to U_BOOT_PHY_DRIVER()

Convert PHY driver to U_BOOT_PHY_DRIVER() macro and drop phy_register() init call.

Converted using sed
"s@^static struct phy_driver $.*$_driver = \+{@U_BOOT_PHY_DRIVER(\L\1) = {"

Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Acked-by: Michal Simek <michal.simek@amd.com>
Tested-by: Michal Simek <michal.simek@amd.com> #microblaze (MANUAL_RELOC)

net: phy: xilinx: Convert to U_BOOT_PHY_DRIVER()

Convert PHY driver to U_BOOT_PHY_DRIVER() macro and drop phy_register() init call.

Converted using sed
"s@^static struct phy_driver $.*$_driver = \+{@U_BOOT_PHY_DRIVER(\L\1) = {"

Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Acked-by: Michal Simek <michal.simek@amd.com>
Tested-by: Michal Simek <michal.simek@amd.com> #microblaze (MANUAL_RELOC)

net: phy: vitesse: Convert to U_BOOT_PHY_DRIVER()

Convert PHY driver to U_BOOT_PHY_DRIVER() macro and drop phy_register() init call.

Converted using sed
"s@^static struct phy_driver $.*$_driver = \+{@U_BOOT_PHY_DRIVER(\L\1) = {"

Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Acked-by: Michal Simek <michal.simek@amd.com>
Tested-by: Michal Simek <michal.simek@amd.com> #microblaze (MANUAL_RELOC)

net: phy: ti: Convert to U_BOOT_PHY_DRIVER()

Convert PHY driver to U_BOOT_PHY_DRIVER() macro and drop phy_register() init call.

Converted using sed
"s@^static struct phy_driver $.*$_driver = \+{@U_BOOT_PHY_DRIVER(\L\1) = {"

This particular PHY driver is slightly more spread out across additional
source files. Since the phy_register() calls are no longer necessary, all
the registration calls across those source files is dropped. Furthermore,
the Makefile can now be updated to only compile generic TI PHY support if
matching Kconfig symbol is enabled and the ifdeffery in the generic TI PHY
driver can be dropped.

Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Acked-by: Michal Simek <michal.simek@amd.com>
Tested-by: Michal Simek <michal.simek@amd.com> #microblaze (MANUAL_RELOC)

net: phy: teranetics: Convert to U_BOOT_PHY_DRIVER()

Convert PHY driver to U_BOOT_PHY_DRIVER() macro and drop phy_register() init call.

Converted using sed
"s@^static struct phy_driver $.*$_driver = \+{@U_BOOT_PHY_DRIVER(\L\1) = {"

Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Acked-by: Michal Simek <michal.simek@amd.com>
Tested-by: Michal Simek <michal.simek@amd.com> #microblaze (MANUAL_RELOC)

net: phy: smsc: Convert to U_BOOT_PHY_DRIVER()

Convert PHY driver to U_BOOT_PHY_DRIVER() macro and drop phy_register() init call.

Converted using sed
"s@^static struct phy_driver $.*$_driver = \+{@U_BOOT_PHY_DRIVER(\L\1) = {"

Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Acked-by: Michal Simek <michal.simek@amd.com>
Tested-by: Michal Simek <michal.simek@amd.com> #microblaze (MANUAL_RELOC)

net: phy: realtek: Convert to U_BOOT_PHY_DRIVER()

Convert PHY driver to U_BOOT_PHY_DRIVER() macro and drop phy_register() init call.

Converted using sed
"s@^static struct phy_driver $.*$_driver = \+{@U_BOOT_PHY_DRIVER(\L\1) = {"

Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Acked-by: Michal Simek <michal.simek@amd.com>
Tested-by: Michal Simek <michal.simek@amd.com> #microblaze (MANUAL_RELOC)

net: phy: nxp-tja11xx: Convert to U_BOOT_PHY_DRIVER()

Convert PHY driver to U_BOOT_PHY_DRIVER() macro and drop phy_register() init call.

Converted using sed
"s@^static struct phy_driver $.*$_driver = \+{@U_BOOT_PHY_DRIVER(\L\1) = {"

Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Acked-by: Michal Simek <michal.simek@amd.com>
Tested-by: Michal Simek <michal.simek@amd.com> #microblaze (MANUAL_RELOC)

net: phy: nxp-c45-tja11xx: Convert to U_BOOT_PHY_DRIVER()

Convert PHY driver to U_BOOT_PHY_DRIVER() macro and drop phy_register() init call.

Converted using sed
"s@^static struct phy_driver $.*$_driver = \+{@U_BOOT_PHY_DRIVER(\L\1) = {"

Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Acked-by: Michal Simek <michal.simek@amd.com>
Tested-by: Michal Simek <michal.simek@amd.com> #microblaze (MANUAL_RELOC)

net: phy: natsemi: Convert to U_BOOT_PHY_DRIVER()

Convert PHY driver to U_BOOT_PHY_DRIVER() macro and drop phy_register() init call.

Converted using sed
"s@^static struct phy_driver $.*$_driver = \+{@U_BOOT_PHY_DRIVER(\L\1) = {"

Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Acked-by: Michal Simek <michal.simek@amd.com>
Tested-by: Michal Simek <michal.simek@amd.com> #microblaze (MANUAL_RELOC)

net: phy: meson-gxl: Convert to U_BOOT_PHY_DRIVER()

Convert PHY driver to U_BOOT_PHY_DRIVER() macro and drop phy_register() init call.

Converted using sed
"s@^static struct phy_driver $.*$_driver = \+{@U_BOOT_PHY_DRIVER(\L\1) = {"

Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Acked-by: Michal Simek <michal.simek@amd.com>
Tested-by: Michal Simek <michal.simek@amd.com> #microblaze (MANUAL_RELOC)

net: phy: ksz90x1: Convert to U_BOOT_PHY_DRIVER()

Convert PHY driver to U_BOOT_PHY_DRIVER() macro and drop phy_register() init call.

Converted using sed
"s@^static struct phy_driver $.*$_driver = \+{@U_BOOT_PHY_DRIVER(\L\1) = {"

Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Acked-by: Michal Simek <michal.simek@amd.com>
Tested-by: Michal Simek <michal.simek@amd.com> #microblaze (MANUAL_RELOC)

net: phy: ksz8xxx: Convert to U_BOOT_PHY_DRIVER()

Convert PHY driver to U_BOOT_PHY_DRIVER() macro and drop phy_register() init call.

Converted using sed
"s@^static struct phy_driver $.*$_driver = \+{@U_BOOT_PHY_DRIVER(\L\1) = {"

Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Acked-by: Michal Simek <michal.simek@amd.com>
Tested-by: Michal Simek <michal.simek@amd.com> #microblaze (MANUAL_RELOC)

net: phy: marvell: Convert to U_BOOT_PHY_DRIVER()

Convert PHY driver to U_BOOT_PHY_DRIVER() macro and drop phy_register() init call.

Converted using sed
"s@^static struct phy_driver $.*$_driver = \+{@U_BOOT_PHY_DRIVER(\L\1) = {"

Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Acked-by: Michal Simek <michal.simek@amd.com>
Tested-by: Michal Simek <michal.simek@amd.com> #microblaze (MANUAL_RELOC)

net: phy: lxt: Convert to U_BOOT_PHY_DRIVER()

Convert PHY driver to U_BOOT_PHY_DRIVER() macro and drop phy_register() init call.

Converted using sed
"s@^static struct phy_driver $.*$_driver = \+{@U_BOOT_PHY_DRIVER(\L\1) = {"

Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Acked-by: Michal Simek <michal.simek@amd.com>
Tested-by: Michal Simek <michal.simek@amd.com> #microblaze (MANUAL_RELOC)

net: phy: et1011c: Convert to U_BOOT_PHY_DRIVER()

Convert PHY driver to U_BOOT_PHY_DRIVER() macro and drop phy_register() init call.

Converted using sed
"s@^static struct phy_driver $.*$_driver = \+{@U_BOOT_PHY_DRIVER(\L\1) = {"

Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Acked-by: Michal Simek <michal.simek@amd.com>
Tested-by: Michal Simek <michal.simek@amd.com> #microblaze (MANUAL_RELOC)

net: phy: mv88e61xx: Convert to U_BOOT_PHY_DRIVER()

Convert PHY driver to U_BOOT_PHY_DRIVER() macro and drop phy_register() init call.

Converted using sed
"s@^static struct phy_driver $.*$_driver = \+{@U_BOOT_PHY_DRIVER(\L\1) = {"

Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Acked-by: Michal Simek <michal.simek@amd.com>
Tested-by: Michal Simek <michal.simek@amd.com> #microblaze (MANUAL_RELOC)

net: phy: davicom: Convert to U_BOOT_PHY_DRIVER()

Convert PHY driver to U_BOOT_PHY_DRIVER() macro and drop phy_register() init call.

Converted using sed
"s@^static struct phy_driver $.*$_driver = \+{@U_BOOT_PHY_DRIVER(\L\1) = {"

Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Acked-by: Michal Simek <michal.simek@amd.com>
Tested-by: Michal Simek <michal.simek@amd.com> #microblaze (MANUAL_RELOC)

net: phy: cortina: Convert to U_BOOT_PHY_DRIVER()

Convert PHY driver to U_BOOT_PHY_DRIVER() macro and drop phy_register() init call.

Converted using sed
"s@^static struct phy_driver $.*$_driver = \+{@U_BOOT_PHY_DRIVER(\L\1) = {"

Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Acked-by: Michal Simek <michal.simek@amd.com>
Tested-by: Michal Simek <michal.simek@amd.com> #microblaze (MANUAL_RELOC)

net: phy: ca_phy: Convert to U_BOOT_PHY_DRIVER()

Convert PHY driver to U_BOOT_PHY_DRIVER() macro and drop phy_register() init call.

Converted using sed
"s@^static struct phy_driver $.*$_driver = \+{@U_BOOT_PHY_DRIVER(\L\1) = {"

Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Acked-by: Michal Simek <michal.simek@amd.com>
Tested-by: Michal Simek <michal.simek@amd.com> #microblaze (MANUAL_RELOC)

net: phy: broadcom: Convert to U_BOOT_PHY_DRIVER()

Convert PHY driver to U_BOOT_PHY_DRIVER() macro and drop phy_register() init call.

Converted using sed
"s@^static struct phy_driver $.*$_driver = \+{@U_BOOT_PHY_DRIVER(\L\1) = {"

Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Acked-by: Michal Simek <michal.simek@amd.com>
Tested-by: Michal Simek <michal.simek@amd.com> #microblaze (MANUAL_RELOC)

net: phy: b53: Convert to U_BOOT_PHY_DRIVER()

Convert PHY driver to U_BOOT_PHY_DRIVER() macro and drop phy_register() init call.

Converted using sed
"s@^static struct phy_driver $.*$_driver = \+{@U_BOOT_PHY_DRIVER(\L\1) = {"

Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Acked-by: Michal Simek <michal.simek@amd.com>
Tested-by: Michal Simek <michal.simek@amd.com> #microblaze (MANUAL_RELOC)

net: phy: atheros: Convert to U_BOOT_PHY_DRIVER()

Convert PHY driver to U_BOOT_PHY_DRIVER() macro and drop phy_register() init call.

Converted using sed
"s@^static struct phy_driver $.*$_driver = \+{@U_BOOT_PHY_DRIVER(\L\1) = {"

Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Acked-by: Michal Simek <michal.simek@amd.com>
Tested-by: Michal Simek <michal.simek@amd.com> #microblaze (MANUAL_RELOC)

net: phy: aquantia: Convert to U_BOOT_PHY_DRIVER()

Convert PHY driver to U_BOOT_PHY_DRIVER() macro and drop phy_register() init call.

Converted using sed
"s@^static struct phy_driver $.*$_driver = \+{@U_BOOT_PHY_DRIVER(\L\1) = {"

Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Acked-by: Michal Simek <michal.simek@amd.com>
Tested-by: Michal Simek <michal.simek@amd.com> #microblaze (MANUAL_RELOC)

net: phy: adin: Convert to U_BOOT_PHY_DRIVER()

Convert PHY driver to U_BOOT_PHY_DRIVER() macro and drop phy_register() init call.

Converted using sed
"s@^static struct phy_driver $.*$_driver = \+{@U_BOOT_PHY_DRIVER(\L\1) = {"

Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Acked-by: Michal Simek <michal.simek@amd.com>
Tested-by: Michal Simek <michal.simek@amd.com> #microblaze (MANUAL_RELOC)

net: phy: Iterate over both registered PHYs and struct phy_driver linker list

Introduce U_BOOT_PHY_DRIVER() macro which is used to add struct phy_driver
into a new linker list section containing all compiled in struct phy_driver
drivers. This is so far empty until PHY drivers are converted over to this
macro.

Iterate over both drivers registered using soon to be legacy phy_register()
as well as drivers in the new linker list when looking up a suitable PHY
driver. This way, PHY drivers can be converted over to the new macro one
driver at a time.

The relocation of callbacks for linker list based drivers now happens in
phy_init() call as the drivers are available at that point in time, and
phy_register() is not called for those drivers.

Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Acked-by: Michal Simek <michal.simek@amd.com>
Tested-by: Michal Simek <michal.simek@amd.com> #microblaze (MANUAL_RELOC)

net: phy: Factor manual relocation into separate function

Create separate function to implement manual relocation of PHY driver
functions and make use of that function. This is a preparatory patch
for introduction of PHY driver definition using linker lists.

No functional change.

Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Acked-by: Michal Simek <michal.simek@amd.com>
Tested-by: Michal Simek <michal.simek@amd.com> #microblaze (MANUAL_RELOC)

net: phy: teranetics: Staticize PHY driver entries

These struct phy_driver ... instances are local to this source code
file, staticize them. No functional change.

Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Acked-by: Michal Simek <michal.simek@amd.com>
Tested-by: Michal Simek <michal.simek@amd.com> #microblaze (MANUAL_RELOC)

net: phy: cortina: Staticize PHY driver entries

These struct phy_driver ... instances are local to this source code
file, staticize them. No functional change.

Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Acked-by: Michal Simek <michal.simek@amd.com>
Tested-by: Michal Simek <michal.simek@amd.com> #microblaze (MANUAL_RELOC)

net: phy: ca_phy: Staticize PHY driver entries

These struct phy_driver ... instances are local to this source code
file, staticize them. No functional change.

Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Acked-by: Michal Simek <michal.simek@amd.com>
Tested-by: Michal Simek <michal.simek@amd.com> #microblaze (MANUAL_RELOC)

net: phy: aquantia: Staticize PHY driver entries

These struct phy_driver ... instances are local to this source code
file, staticize them. No functional change.

Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Acked-by: Michal Simek <michal.simek@amd.com>
Tested-by: Michal Simek <michal.simek@amd.com> #microblaze (MANUAL_RELOC)
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>

Merge tag 'fsl-qoriq-2023-4-6' of https://source.denx.de/u-boot/custodians/u-boot-fsl-qoriq

convert NXP LS1028A RDB and QDS to DM_SERIAL
enable DM_SERIAL for ls1088a
sync serial nodes with linux for lx2160a/ls1088a

Merge branch '2023-04-05-blkmap-composable-virtual-block-devices'

To quote the author:
Block maps are a way of looking at various sources of data through the
lens of a regular block device. It lets you treat devices that are not
block devices, like RAM, as if they were. It also lets you export a
slice of an existing block device, which does not have to correspond to
a partition boundary, as a new block device.

This is primarily useful because U-Boot's filesystem drivers only
operate on block devices, so a block map lets you access filesystems
wherever they might be located.

The implementation is loosely modeled on Linux's "Device Mapper"
subsystem, see the kernel documentation [1] for more information.

The primary use-cases are to access filesystem images stored in RAM, and
within FIT images stored on disk. See doc/usage/blkmap.rst for more
details.

The architecture is pluggable, so adding other types of mappings should
be quite easy.

[1]: https://docs.kernel.org/admin-guide/device-mapper/index.html

efi_loader: device_path: support blkmap devices

Create a distinct EFI device path for each blkmap device.

Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

doc: blkmap: Add introduction and examples

Explain block maps by going through two common use-cases.

Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

test: blkmap: Add test suite

Verify that:

- Block maps can be created and destroyed
- Mappings aren't allowed to overlap
- Multiple mappings can be attached and be read/written from/to

Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

cmd: blkmap: Add blkmap command

Add a frontend for the blkmap subsystem. In addition to the common
block device operations, this allows users to create and destroy
devices, and map in memory and slices of other block devices.

With that we support two primary use-cases:

- Being able to "distro boot" from a RAM disk. I.e., from an image
  where the kernel is stored in /boot of some filesystem supported
  by U-Boot.

- Accessing filesystems not located on exact partition boundaries,
  e.g. when a filesystem image is wrapped in an FIT image and stored
  in a disk partition.

Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

blk: blkmap: Add linear device mapping support

Allow a slice of an existing block device to be mapped to a
blkmap. This means that filesystems that are not stored at exact
partition boundaries can be accessed by remapping a slice of the
existing device to a blkmap device.

Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

blk: blkmap: Add memory mapping support

Allow a slice of RAM to be mapped to a blkmap. This means that RAM can
now be accessed as if it was a block device, meaning that existing
filesystem drivers can now be used to access ramdisks.

Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

blk: blkmap: Add basic infrastructure

blkmaps are loosely modeled on Linux's device mapper subsystem. The
basic idea is that you can create virtual block devices whose blocks
can be backed by a plethora of sources that are user configurable.

This change just adds the basic infrastructure for creating and
removing blkmap devices. Subsequent changes will extend this to add
support for actual mappings.

Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

cmd: blk: Allow generic read/write operations to work in sandbox

Ensure that the memory destination/source addresses of block
read/write operations are mapped in before access. Currently, this is
only needed on sandbox builds.

Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

image: Fix script execution from FIT images with external data

Update the script loading code to recognize when script data is stored
externally from the FIT metadata (i.e., built with `mkimage -E`).

Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

Merge branch '2023-04-04-android-image-v3-v4-support'

To quote the author:
* This is based on Roman Stratiienko's work to support boot image header version 3 and 4.

* This supports the new boot image headers v3, v4 and bootconfig feature.
https://source.android.com/docs/core/architecture/bootloader/boot-image-header
https://source.android.com/docs/core/architecture/bootloader/implementing-bootconfig

- Tested on Amlogic Khadas vim3l, a reference board for Android Open Source Project
https://www.khadas.com/vim3l

And on AM625 Texas Instruments board with 5.10 linux kernel

Main changes :
- New partition : vendor boot, with a specific vendor ramdisk
- DTB is stored in the vendor boot partition
- The generic ramdisk is placed after the vendor ramdisk
- Bootconfig feature support

Here is a link to see the related android boot flow changes on KHADAS vim3l as an example:
https://gitlab.baylibre.com/baylibre/amlogic/atv/u-boot/-/commits/souajih/BootImagev4/

Dockerfile: add mkbootimg tool

mkbootimg tool is part of the Android project and it is
used to pack Android boot images such as boot image
and vendor_boot image.

Use the following command to run mkbootimg:
$ python3 -m mkbootimg

Add mkbootimg to the docker file

Signed-off-by: Safae Ouajih <souajih@baylibre.com>
Tested-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>

test/py: android: extend abootimg test

test_abootimg is extended to include the testing of boot images
version 4. For this, boot.img and vendor_boot.img have been
generated using mkbootimg tool with setting the header
version to 4.

This tests:
- Getting the header version using abootimg
- Extracting the load address of the dtb
- Extracting the dtb start address in RAM

Running test:
$ ./test/py/test.py --bd sandbox --build -k test_abootimg

Signed-off-by: Safae Ouajih <souajih@baylibre.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>

doc: android: add documentation for v3, v4 boot image header

Update the Android documentation to describe version 3 and 4 of boot
image header.

Signed-off-by: Safae Ouajih <souajih@baylibre.com>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>

android: boot: support bootconfig

Support Bootconfig feature.
- The bootconfig feature replaces the androidboot.*
kernel cmdline options.

This was adapted from downstream [1] commit : 7af0a0506d4d ("cuttlefish:
support bootconfig parameters").

Link:[1] https://android.googlesource.com/platform/external/u-boot/

Signed-off-by: Safae Ouajih <souajih@baylibre.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Tested-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>

android: boot: support boot image header version 3 and 4

Enable the support for boot image header version 3 and 4
using abootimg command.

In order to use version 3 or 4:

1- Vendor boot image address should be given to abootimg cmd.

abootimg addr $1 $vendor_boot_load_addr

2- "ramdisk_addr_r" env variable (ramdisk address) should be set to host
the ramdisk : generic ramdisk + vendor ramdisk

Replace "struct andr_boot_img_hdr_v0*" by "void *" in
some functions since v3 and v4 are now supported as well.

Signed-off-by: Safae Ouajih <souajih@baylibre.com>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Tested-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>

drivers: fastboot: zImage flashing is not supported for v3, v4

With vendor boot image introduced in version 3 and 4 of boot
image header, boot information is located in both boot image
and vendor boot image.

Flashing zImage is not supported for version 3 and 4 since this
requires updating vendor boot image and/or generating a new image.

Print an error message when the boot image header version is
greater than 2.

Signed-off-by: Safae Ouajih <souajih@baylibre.com>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Tested-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>

android: boot: update android_image_get_dtb_img_addr to support v3, v4

Add support for boot image version 3 and 4 in
android_image_get_dtb_img_addr().
Since the dtb is now included in vendor_boot image
instead of boot image, extract the dtb address from
vendor_boot image when a v3 or v4 is used.

Signed-off-by: Safae Ouajih <souajih@baylibre.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Tested-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>

android: boot: support extra command line

In version 3 and 4 of boot image header, the vendor specific
command line are located in vendor boot image. Thus, use
extra command line to add those cmd to bootargs.

Signed-off-by: Safae Ouajih <souajih@baylibre.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Tested-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>

android: boot: ramdisk: support vendor ramdisk

Version 3 and 4 of boot image header introduced
vendor boot ramdisk: Please check include/android_image.h
for details.

The ramdisk is now split into a generic ramdisk in boot image
and a vendor ramdisk in vendor boot image.

Support the new vendor ramdisk.

Signed-off-by: Safae Ouajih <souajih@baylibre.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Tested-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>

android: boot: update android_image_get_data to support v3, v4

Since boot image header version 3 and 4 introduced vendor boot image,
use the following functions to fill the generic android
structure : andr_image_data:

- android_boot_image_v3_v4_parse_hdr()
- android_vendor_boot_image_v3_v4_parse_hdr()

Update android_image_get_data() to support v3 and v4

Signed-off-by: Safae Ouajih <souajih@baylibre.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Tested-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>

android: boot: add vendor boot image to prepare for v3, v4 support

Introduce vendor boot image for version 3 and 4 of boot image header.
The vendor boot image will hold extra information about kernel, dtb
and ramdisk.

This is done to prepare for boot image version 3 and 4 support.

Signed-off-by: Safae Ouajih <souajih@baylibre.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Tested-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>

android: boot: boot image header v3, v4 do not support recovery DTBO

android_image_get_dtbo() is used to get recovery DTBO via abootimg cmd.
This is not supported in boot image header v3 and v4. Thus, print an
error message when v1,v2 header version are not used.

Signed-off-by: Safae Ouajih <souajih@baylibre.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Tested-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>

android: boot: content print is not supported for v3, v4 header version

Content print is not supported for version 3 and 4 of boot image header.
Thus, only print that content when v2 is used.

Update android_print_contents() to print an error message
when trying to print boot image header version 3 or 4 content.

Signed-off-by: Safae Ouajih <souajih@baylibre.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Tested-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>

android: boot: move to andr_image_data structure

Move from andr_boot_img_hdr_v0 to andr_image_data
structure to prepare for boot image header
version 3 and 4.

Signed-off-by: Safae Ouajih <souajih@baylibre.com>
Tested-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>

android: boot: kcomp: support andr_image_data

andr_image_data structure is used as a global representation of
boot image header structure. Introduce this new structure to
support all boot header versions : v0,v1.v2.v3.v4 and to support
v3 and v4 while maitaining support for v0,v1,v2.
The need of using andr_image_data comes from the change of header
structure in both version 3 and 4.

Rework android_image_get_kcomp() to support this new struct.

Signed-off-by: Safae Ouajih <souajih@baylibre.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Tested-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>

android: boot: add boot image header v3 and v4 structures

Add support for v3/v4 boot image format by adding
the following structures:

- andr_boot_img_hdr_v3 : describes boot image header
- andr_vnd_boot_img_hdr : describes vendor boot image header

These definitions have been copied over from the AOSP documentation at
[1] and [2]

Boot arg sizes are taken from [3]:
commit: 35fb6262bc3f (ANDROID: Support for vendor boot)

This also adds documentation for boot image header v3/v4 structure
that was imported from [4], file: include/bootimg/bootimg.h
commit: 8d0922bfb932 (Adding GKI signature in boot.img v4)

Link:[1] https://source.android.com/docs/core/architecture/bootloader/boot-image-header
Link:[2] https://source.android.com/docs/core/architecture/bootloader/partitions/vendor-boot-partitions#vendor-boot-header
Link:[3] https://android.googlesource.com/platform/external/u-boot
Link:[4] https://android.googlesource.com/platform/system/tools/mkbootimg

Signed-off-by: Safae Ouajih <souajih@baylibre.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Tested-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>

android: boot: replace android_image_check_header

With the new vendor boot image introduced in versions 3 and 4
of boot image header, the header check must be done for both boot
image and vendor boot image. Thus, replace android_image_check_header()
by is_android_boot_image_header() to only refer to boot image header check.

Signed-off-by: Safae Ouajih <souajih@baylibre.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Tested-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>

android: boot: support vendor boot image in abootimg

Vendor boot image is introduced in boot image header
version 3 and 4. Please check [1] for more details.

To prepare for boot image v3/v4 support, allow the abootimg command
to store the vendor_boot image address.

Full support for this new format will be done in a future patch.

Link:[1] https://source.android.com/docs/core/architecture/bootloader/partitions/vendor-boot-partitions

Signed-off-by: Safae Ouajih <souajih@baylibre.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Tested-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>

android: boot: rename andr_img_hdr -> andr_boot_img_hdr_v0

Android introduced boot header version 3 or 4.
The header structure change with version 3 and 4 to support
the new updates such as:
- Introducing Vendor boot image: with a vendor ramdisk
- Bootconfig feature (v4)

Change andr_img_hdr struct name to maintain support for version v0,
v1 and v2 while introducing version 3 and 4.

Signed-off-by: Safae Ouajih <souajih@baylibre.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Tested-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>

Merge branch '2023-04-04-update-to-clang-16'

- Update our CI to use clang-16 for tests. This also changes slightly
  how we do linker lists so that we don't rely on undefined behavior
  that lead to clang-15 and later failing to work (and in some cases
  seemingly, earlier versions of clang would sometimes fail).

CI: Move to clang-16

As this is now the stable release, move to using that now for our tests.

Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

linker_lists: Rework start/end macros to not rely on undefined behavior

Per the GCC bug listed below, the way we do linker lists is relying on
undefined behavior that seems to work in gcc, but doesn't always work in
clang. Andrew suggests rewriting our start/end macros in a different way
(as implemented here, from what he said in comment 1) to avoid these
problems.

Reported-by: AdityaK <appujee@google.com>
Suggested-by: Andrew Pinski <apinski@marvell.com>
Link: https://gcc.gnu.org/bugzilla/show_bug.cgi?id=108915
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Andrew Pinski <apinski@marvell.com>

smartweb: Enable LTO

In order to prepare for slight size growth due to reworking linker list
support, enable LTO here to save more space again.

Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heiko Schocher <hs@denx.de>

Dockerfile: Populate a pip cache

Given the number of jobs in CI we have which use python and pip install
packages, we should do this once in the Dockerfile, in order to populate
the cache. We let each job continue to create and use the virtual
environments they need to facilitate making updates to these
environments easier.

Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

pytest: Update requirements to match sphinx versions

In order to better make use of pip caches, and also for better overall
consistency, we should use the same versions of packages in each of our
python requirements files. Update pytest to use the newer versions of
packages we use in sphinx builds.

Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

Merge tag 'u-boot-imx-next-20230404' of https://gitlab.denx.de/u-boot/custodians/u-boot-imx

u-boot-imx-next-20230404
------------------------

CI : https://source.denx.de/u-boot/custodians/u-boot-imx/-/pipelines/15887

- boards : DH-Electronics, Toradex, imx8mp-beacon-kit

board: freescale: lx2160a: remove the PL01X device instantiation

There is no need for the board file to instantiate a PL01X platform
device anymore. This is all taken care of by the DM code which now will
probe the device based on the DT node.

Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>

arch: arm: dts: fsl-lx2160a.dtsi: tag serial nodes with bootph-all

Tag the serial nodes with bootph-all in order to have these nodes and
the drivers available before relocation.

Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>

arch: arm: dts: fsl-lx2160a.dtsi: sync serial nodes with Linux

Sync the serial nodes of the LX2160A based boards with their
representation in Linux. We also imported the clockgen and sysclk nodes
which are dependencies.

Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>

arch: arm: dts: fsl-lx2160a.dtsi: move the serial nodes under soc

Move the serial nodes under the soc node. No changes are made to the
nodes, just their location is changed.

Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>

arch: arm: dts: fsl-lx2160a.dtsi: add an 'soc' node

The u-boot dts for these boards do not have an soc node, unlike its
Linux counterpart. This patch just adds the soc node as seen in Linux,
the next patches will move some nodes under it.

Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>

configs: ls1088a: enable DM_SERIAL

Now that the DT nodes for the serial devices are in place for these
boards, enable DM_SERIAL in the associated configs.

Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>

arch: arm: dts: fsl-ls1088a.dtsi: tag serial nodes with bootph-all

Tag the serial nodes with bootph-all in order to have these nodes and
the drivers available before relocation.

Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>

arch: arm: dts: fsl-ls1088a.dtsi: sync serial nodes with Linux

Sync the serial nodes of the LS1088A based boards with their
representation in Linux. We also imported the clockgen and sysclk nodes
which are dependencies.

Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>

arch: arm: dts: fsl-ls1088a.dtsi: move the serial nodes under soc

Move the serial nodes under the soc node. No changes are made to the
nodes, just their location is changed.

Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>

arch: arm: dts: fsl-ls1088a.dtsi: add an 'soc' node

The u-boot dts for these boards do not have an soc node, unlike its
Linux counterpart. This patch just adds the soc node as seen in Linux,
the next patches will move some nodes under it.

Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>

configs: convert NXP LS1028A RDB and QDS to DM_SERIAL

Since the device trees are more or less synchronized with Linux, the
only necessary changes are to enable CONFIG_DM_SERIAL and the DM_SERIAL
driver for ns16550 (ns16550.c rather than serial_ns16550.c).

ls1028aqds_tfa_lpuart_defconfig already uses DM_SERIAL for the LPUART
driver, so I didn't touch that.

Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>

arm64: imx: Add support for imx8mp-beacon-kit

Beacon Embedded has an i.MX8M Plus development kit which consists
of a SOM + baseboard. The SOM includes Bluetooth, WiFi, QSPI, eMMC,
and one Ethernet PHY. The baseboard includes audio, HDMI, USB-C Dual
Role port, USB Hub with five ports, a PCIe slot, and a second Ethernet
PHY. The device trees are already queued for inclusion in Linux 6.3.

Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>

ARM: imx: Enable LTO for DH electronics i.MX6 DHCOM

Enable LTO to reduce the size of SPL, which with SPL SDP
support may be close to the limit.

Signed-off-by: Marek Vasut <marex@denx.de>

ARM: dts: imx: Add support for Data Modul i.MX8M Plus eDM SBC

Add support for Data Modul i.MX8M Plus eDM SBC board. This is an
evaluation board for various custom display units. Currently
supported are serial console, ethernet, eMMC, SD, SPI NOR, USB.

Signed-off-by: Marek Vasut <marex@denx.de>

ARM: dts: imx: Add WDT reboot bindings on DH i.MX6 DHSOM

Add WDT reboot bindings on DH i.MX6 DHSOM to permit the platform
to reboot via WDT in U-Boot. These are custom U-Boot bindings,
hence they are placed in -u-boot.dtsi .

Reviewed-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Marek Vasut <marex@denx.de>

board: verdin-imx8mp: change prints in spl_dram_init function

change prints to show which DDR configuration (single/dual rank) is used

Signed-off-by: Emanuele Ghidoli <emanuele.ghidoli@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>

board: verdin-imx8mp: compact slight different lpddr4 configuration

Deduplicate similar DDRC configurations and LPDDR4 training patterns
by patching a single configuration.

The aim is to reduce the SPL memory footprint and simplify maintenance
of lpddr4_timing.c

Signed-off-by: Emanuele Ghidoli <emanuele.ghidoli@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>

board: verdin-imx8mp: update lpddr4 configuration and training

Update LPDDR4 configuration and training using updated spreadsheet and
tools from NXP using data from previous spreadsheet and verified
toward datasheet:
- MX8M_Plus_LPDDR4_RPA_v9.xlsx
- mscale_ddr_tool_v3.30.exe

From:
https://community.nxp.com/t5/i-MX-Processors-Knowledge-Base/i-MX-8M-Family-DDR-Tool-Release/ta-p/1104467

Some register values differ due to these fixes/modifications:

- corrected calculation of T_CKPDX parameter (equal to tCKCKEH for LPDDR4)
- corrected ECC related items, none of which affect normal operation
when ECC is not enabled
- corrected formula for calculation of tRTP in cell D122

Signed-off-by: Emanuele Ghidoli <emanuele.ghidoli@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>