sf: probe: Enable macronix quad read/write cmds support
Added macronix flash quad read/write commands support and
it's up to the respective controller driver usecase to
configure the respective commands by defining SPI RX/TX
operation modes from include/spi.h on the driver.
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
This patch provides support to set the quad enable bit on flash.
quad enable bit needs to set before performing any quad IO
operations on respective SPI flashes.
Currently added set quad enable bit for winbond and spansion flash
devices. stmicro flash doesn't require to set as qeb is volatile.
remaining flash devices support will add in future patches.
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Current sf uses FAST_READ command, this patch adds support to
use the different/extended read command.
This implementation will determine the fastest command by taking
the supported commands from the flash and the controller, controller
is always been a priority.
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Axel Lin [Fri, 27 Dec 2013 05:51:55 +0000 (13:51 +0800)]
spi: sh_spi: Use sh_spi_clear_bit() instead of open-coded
We have a sh_spi_clear_bit() function, there's no reason not to use it.
Signed-off-by: Axel Lin <axel.lin@ingics.com> Acked-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org> Reviewed-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Kuo-Jung Su [Fri, 20 Dec 2013 07:24:30 +0000 (12:54 +0530)]
spi: Add Faraday SPI controller support
The Faraday FTSSP010 is a multi-function controller
which supports I2S/SPI/SSP/AC97/SPDIF. However This
patch implements only the SPI mode.
NOTE:
The DMA and CS/Clock control logic has been altered
since hardware revision 1.19.0. So this patch
would first detects the revision id of the underlying
chip, and then switch to the corresponding software
control routines.
Signed-off-by: Kuo-Jung Su <dantesu@faraday-tech.com> Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com> CC: Tom Rini <trini@ti.com>
Enabled default dts files on respective pre-board config
files this is way MAKEALL will works. and it's upto user
to build specific dts by specifying at build time.
$ make zynq_zc70x_config
$ make --> with default dts zynq-zc702.dts
or
$ make DEVICE_TREE=zynq-zc702 --> Same configuration with zynq-zc706.dts
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
ZC770 is a complete development board based on the Xilinx Zynq-7000
All Programmable SoC, similar to ZC70x board but which has four
different daughter cards, like XM010, XM011, XM012 and XM013
ZC770 is a complete development board based on the Xilinx Zynq-7000
All Programmable SoC, similar to ZC70x board but which has four
different daughter cards, like XM010, XM011, XM012 and XM013
ZC770 is a complete development board based on the Xilinx Zynq-7000
All Programmable SoC, similar to ZC70x board but which has four
different daughter cards, like XM010, XM011, XM012 and XM013
MicroZed is a low-cost development board based on
the Xilinx Zynq-7000 All Programmable SoC.
APSOC:
- XC7Z010-1CLG400C
Memory:
- 1 GB of DDR3 SDRAM
- 128Mb of QSPI flash(S25FL128SAGBHI200)
- Micro SD card interface
Communication:
- 10/100/1000 Ethernet
- USB 2.0
- USB-UART
User I/O:
- 100 User I/O (50 per connector)
- Configurable as up to 48 LVDS pairs or 100 single-ended I/O
Misc:
- Xilinx PC4 JTAG configuration port
- PS JTAG pins accessible via Pmod
- 33.33 MHz oscillator
- User LED and push switch
For more info - http://zedboard.org/product/microzed
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
The Zynq-7000 APSOC zc702 and zc706 enabled complte embedded
processing includes ASIC and FPGA design.
ZC702-:
APSOC:
- XC7Z020-CLG484-1
Memory:
- DDR3 Component Memory 1GB
- 16MB Quad SPI Flash
- IIC - 1 KB EEPROM
Connectivity:
- Gigabit Ethernet GMII, RGMII and SGMII.
- USB OTG - Host USB
- IIC Bus Headers/HUB
- 1 CAN with Wake on CAN
- USB-UART
Video/Display:
- HDMI Video OUT
- 8X LEDs
Control & I/O:
- 3 User Push Buttons
- 2 User Switches
- 8 User LEDs
For more info on zc702 board:
- http://www.xilinx.com/products/boards-and-kits/EK-Z7-ZC702-G.htm
ZC706-:
APSOC:
- XC7Z045 FFG900 -2 AP SoC
Memory:
- DDR3 Component Memory 1GB (PS)
- DDR3 SODIM Memory 1GB (PL)
- 2X16MB Quad SPI Flash (dual parallel)
- IIC - 1 KB EEPROM
Connectivity:
- PCIe Gen2x4
- SFP+ and SMA Pairs
- GigE RGMII Ethernet (PS)
- USB OTG 1 (PS) - Host USB
- IIC Bus Headers/HUB (PS)
- 1 CAN with Wake on CAN (PS)
- USB-UART
Video/Display:
- HDMI 8 color RGB 4.4.4 1080P-60 OUT
- HDMI IN 8 color RGB 4.4.4
Control & I/O:
- 2 User Push Buttons/Dip Switch, 2 User LEDs
- IIC access to GPIO
- SDIO (SD Card slot)
- 3 User Push Buttons, 2 User Switches, 8 User LEDs
For more info on zc706 board:
- http://www.xilinx.com/products/boards-and-kits/EK-Z7-ZC706-G.htm
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Zynq ethernet controller support two GEM's like
CONFIG_ZYNQ_GEM0 and CONFIG_ZYNQ_GEM1 enabled
both so-that the respective board will define
these macros based on their usage.
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Zynq uart controller support two serial ports like
CONFIG_ZYNQ_SERIAL_UART0 and CONFIG_ZYNQ_SERIAL_UART1
enabled both so-that the respective board will define
these macros based on their usage.
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Albert ARIBAUD [Fri, 10 Jan 2014 09:19:45 +0000 (10:19 +0100)]
arm: make 'MAKEALL -a' distinguish between arm and aarch64
The vexpress_aemv8a is the first aarch64 board in U-Boot.
As it was introduced, it gets built when "MAKEALL -a arm"
is invoked, and fails as this command is run with a 32-bit,
not 64-bit, toolchain as the cross-compiler.
Introduce 'aarch64' as a valid 'MAKEALL -a' argument, treated
as 'arm' for all other intents, and change the architecture
of the vexpress_aemv8a entry in boards.cfg from 'arm' to
'aarch64'.
Tom Rini [Thu, 9 Jan 2014 20:11:27 +0000 (15:11 -0500)]
armv8: Use __aarch64__ rather than CONFIG_ARM64 in some cases
The toolchain sets __aarch64__ for both LE and BE. In the case of
posix_types.h we cannot reliably use config.h as that will lead to
problems. In the case of byteorder.h it's clearer to check the EB flag
being set in either case instead.
Cc: David Feng <fenghua@phytium.com.cn> Signed-off-by: Tom Rini <trini@ti.com>
Amended by Albert ARIBAUD <albert.u.boot@aribaud.net> to
actually remove the config.h include from the posix_types.h
files, with permission from Tom Rini.
David Feng [Sat, 14 Dec 2013 03:47:35 +0000 (11:47 +0800)]
arm64: core support
Relocation code based on a patch by Scott Wood, which is: Signed-off-by: Scott Wood <scottwood@freescale.com> Signed-off-by: David Feng <fenghua@phytium.com.cn>
Scott Wood [Sat, 14 Dec 2013 03:47:33 +0000 (11:47 +0800)]
arm64: Turn u-boot.bin back into an ELF file after relocate-rela
While performing relocations on u-boot.bin should be good enough for
booting on real hardware, some simulators insist on booting an ELF file
(and yet don't perform ELF relocations), so convert the relocated
binary back into an ELF file. This can go away in the future if we
change relocate-rela to operate directly on the ELF file, or if and
when we stop caring about a simulator with this restriction.
Signed-off-by: Scott Wood <scottwood@freescale.com> Signed-off-by: David Feng <fenghua@phytium.com.cn>
Scott Wood [Sat, 14 Dec 2013 03:47:32 +0000 (11:47 +0800)]
arm64: Add tool to statically apply RELA relocations
ARM64 uses the newer RELA-style relocations rather than the older REL.
RELA relocations have an addend in the relocation struct, rather than
expecting the loader to read a value from the location to be updated.
While this is beneficial for ordinary program loading, it's problematic
for U-Boot because the location to be updated starts out with zero,
rather than a pre-relocation value. Since we need to be able to run C
code before relocation, we need a tool to apply the relocations at
build time.
In theory this tool is applicable to other newer architectures (mainly
64-bit), but currently the only relocations it supports are for arm64,
and it assumes a 64-bit little-endian target. If the latter limitation
is ever to be changed, we'll need a way to tell the tool what format
the image is in. Eventually this may be replaced by a tool that uses
libelf or similar and operates directly on the ELF file. I've written
some code for such an approach but libelf does not make it easy to poke
addresses by memory address (rather than by section), and I was
hesitant to write code to manually parse the program headers and do the
update outside of libelf (or to iterate over sections) -- especially
since it wouldn't get test coverage on things like binaries with
multiple PT_LOAD segments. This should be good enough for now to let
the manual relocation stuff be removed from the arm64 patches.
Signed-off-by: Scott Wood <scottwood@freescale.com> Signed-off-by: David Feng <fenghua@phytium.com.cn>
Chin Liang See [Tue, 31 Dec 2013 00:26:14 +0000 (18:26 -0600)]
socfpga/dwmmc: Adding DesignWare MMC driver support for SOCFPGA
To add the DesignWare MMC driver support for Altera SOCFPGA. It
required information such as clocks and bus width from platform
specific files (SOCFPGA handoff files)
Signed-off-by: Chin Liang See <clsee@altera.com> Cc: Rajeshwari Shinde <rajeshwari.s@samsung.com> Cc: Jaehoon Chung <jh80.chung@samsung.com> Cc: Pantelis Antoniou <panto@antoniou-consulting.com> Cc: Wolfgang Denk <wd@denx.de> Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Markus Niebel [Mon, 16 Dec 2013 12:40:46 +0000 (13:40 +0100)]
mmc: add setdsr support
The eMMC and the SD-Card specifications describe the optional SET_DSR command.
During measurements at our lab we found that some cards implementing this feature
having really strong driver strengts per default. This can lead to voltage peaks
above the specification of the host on signal edges for data sent from a card to
the host.
Since availability of a given card type may be shorter than the time a certain
hardware will be produced it is useful to have support for this command (Alternative
would be changing termination resistors and adapting the driver strength of the
host to the used card.)
Following proposal for an implementation:
- new field that reflects CSD field DSR_IMP in struct mmc
- new field for design specific DSR value in struct mmc
- board code can set DSR value in mmc struct just after registering an controller
- mmc_startup sends the the stored DSR value before selecting a card, if DSR_IMP is set
Additionally the mmc command is extended to make is possible to play around with different
DSR values.
The concept was tested on a i.MX53 based platform using a Micron eMMC card where the default
DSR is 0x0400 (12mA) but in our design 0x0100 (0x0100) were enough. To use this feature for
instance on a mx53loco one have to add a call to mmc_set_dsr() in board_mmc_init() after
calling fsl_esdhc_initialize() for the eMMC.
Signed-off-by: Markus Niebel <Markus.Niebel@tqs.de> Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Alexey Brodkin [Thu, 26 Dec 2013 11:29:07 +0000 (15:29 +0400)]
mmc/dwmmc: use bounce buffer for data exchange between CPU and MMC controller
Bounce buffer implementation takes care of proper data buffer alignemt
and correct flush/invalidation of data cache at once so we no longer
depend on input data variety and make sure CPU and MMC controller deal
with expected data in case of enabled data cache.
Bounce buffer requires to add its definition (CONFIG_BOUNCE_BUFFER) in
board configuration, otherwise corresponding library won't be compiled
and linker will fail to build resulting executable.
Difference since v1 - fixed compile-time warning with type casting to
"void *":
Slight edit to remove UTF8 characters in the commit message.
Acked-by: Jaehoon Chung <jh80.chung@samsung.com> Tested-by: Jaehoon Chung <jh80.chung@samsung.com> Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
====
passing argument 2 of 'bounce_buffer_start' discards 'const' qualifier
from pointer target type
====
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com> Cc: Mischa Jonker <mjonker@synopsys.com> Cc: Alim Akhtar <alim.akhtar@samsung.com> Cc: Rajeshwari Shinde <rajeshwari.s@samsung.com> Cc: Jaehoon Chung <jh80.chung@samsung.com> Cc: Amar <amarendra.xt@samsung.com> Cc: Kyungmin Park <kyungmin.park@samsung.com> Cc: Minkyu Kang <mk7.kang@samsung.com> Cc: Simon Glass <sjg@chromium.org> Cc: Pantelis Antoniou <panto@antoniou-consulting.com> Cc: Andy Fleming <afleming@gmail.com>
sh: sh4: Remove CONFIG_SH4A definition from source code
SH4 and SH4A are compatible. But some instructions are different from these.
In Linux kernel, It is treated as a separate CPU, but for now, I think that
there is no need to divide especially in the U-Boot.
This removes CONFIG_SH4A definition from source code, SH4A is treated as SH4.
And this fix white space.
Simon Glass [Sun, 10 Nov 2013 17:27:04 +0000 (10:27 -0700)]
sandbox: Add facility to save/restore sandbox state
It is often useful to be able to save out the state from a sandbox test
run, for analysis or to restore it later to continue a test. Add generic
infrastructure for doing this using a device tree binary file. This is
a flexible tagged file format which is already supported by U-Boot, and
it supports hierarchy if needed.
Signed-off-by: Simon Glass <sjg@chromium.org> Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Hung-ying Tyan <tyanh@chromium.org>
Simon Glass [Sun, 10 Nov 2013 17:27:03 +0000 (10:27 -0700)]
sandbox: Allow reading/writing of RAM buffer
It is useful to be able to save and restore the RAM contents of sandbox
U-Boot either for setting up tests, for later analysys, or for chaining
together multiple tests which need to keep the same memory contents.
Add a function to provide a memory file for U-Boot. This is read on
start-up and written when shutting down. If the file does not exist
on start-up, it will be created when shutting down.
Signed-off-by: Simon Glass <sjg@chromium.org> Signed-off-by: Simon Glass <sjg@chromium.org>
Simon Glass [Sun, 10 Nov 2013 17:27:02 +0000 (10:27 -0700)]
sandbox: Add -i option to enter interactive mode
Normally when U-Boot starts with a command (-c option) it quits when the
command completes. Normally this is what is requires, since the test is
likely complete.
Provide an option to jump into the console instead, so that debugging or
other tasks may be performed before quitting.
Signed-off-by: Simon Glass <sjg@chromium.org> Signed-off-by: Simon Glass <sjg@chromium.org>
Simon Glass [Sun, 10 Nov 2013 17:27:01 +0000 (10:27 -0700)]
sandbox: Allow the console to work earlier
With sandbox, errors and problems may be reported before console_init_f()
is executed. For example, an argument may not parse correctly or U-Boot may
panic(). At present this output is swallowed so there is no indication what
is going wrong.
Adjust the console to deal with a very early sandbox setup, by detecting that
there is no global_data yet, and calling os functions in that case.
Signed-off-by: Simon Glass <sjg@chromium.org> Signed-off-by: Simon Glass <sjg@chromium.org>
Simon Glass [Sun, 10 Nov 2013 17:27:00 +0000 (10:27 -0700)]
sandbox: Implement the bootm command for sandbox
When sandbox does a 'bootm' to run a kernel we cannot actually execute it.
So just exit sandbox, which is essentially what U-Boot does on other archs.
Also, allow sandbox to use bootm on any kernel, so that it can be used
to test booting of kernels from any architecture.
Signed-off-by: Simon Glass <sjg@chromium.org> Signed-off-by: Simon Glass <sjg@chromium.org>
Simon Glass [Sun, 10 Nov 2013 17:26:59 +0000 (10:26 -0700)]
sandbox: Allow return from board_init_f()
The execution flow becomes easier if we can return from board_init_f()
as ARM does. We can control things from start.c instead of having to
call back into that file from other places.
Signed-off-by: Simon Glass <sjg@chromium.org> Signed-off-by: Simon Glass <sjg@chromium.org>
Henrik Nordström [Sun, 10 Nov 2013 17:26:56 +0000 (10:26 -0700)]
sandbox: block driver using host file/device as backing store
Provide a way to use any host file or device as a block device in U-Boot.
This can be used to provide filesystem access within U-Boot to an ext2
image file on the host, for example.
The support is plumbed into the filesystem and partition interfaces.
We don't want to print a message in the driver every time we find a missing
device. Pass the information back to the caller where a message can be printed
if desired.
Signed-off-by: Henrik Nordström <henrik@henriknordstrom.net> Signed-off-by: Simon Glass <sjg@chromium.org>
- Removed change to part.c get_device_and_partition()
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Simon Glass <sjg@chromium.org>
Chin Liang See [Wed, 18 Dec 2013 17:16:01 +0000 (11:16 -0600)]
mmc/dwmmc: Using calloc instead malloc
To enhance the SDMMC DesignWare driver to use calloc instead of
malloc. This will avoid the incident that uninitialized members
of mmc structure are later used for NULL comparison.
Lad, Prabhakar [Tue, 3 Dec 2013 06:47:34 +0000 (12:17 +0530)]
include/mmc.h: Remove declaration for spl_mmc_load()
The spl_mmc_load() was removed while converting to
CONFIG_SPL_FRAMEWORK usage the definition was removed
but the declaration was missed. This patch removes this
declaration.
sh: sh2: Change CONFIG_SYS_HZ to CONFIG_SH_CMT_CLK_FREQ
CONFIG_SYS_HZ of SH2 is not used as frequency of base timer. This is the
correct clock of CMT.
This changes from CONFIG_SYS_HZ to CONFIG_SH_CMT_CLK_FREQ, in order to use
CONFIG_SYS_HZ as clock of CMT.
Nikita Kiryanov [Tue, 31 Dec 2013 10:55:15 +0000 (12:55 +0200)]
arm: omap: cm_t35: enable gpio bank 5 clocks explicitly
Following commit "arm: omap3: Enable clocks for peripherals only if they are
used" (f33b9bd3984fb11e1d8566a866adc5957b1e1c9d) it is now necessary to enable
clocks for GPIO banks explicitly. On cm_t35, GPIO bank 5 is necessary for
scf0403 lcd support.
Enable GPIO bank 5 clocks.
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il> Cc: Igor Grinberg <grinberg@compulab.co.il> Cc: Tom Rini <trini@ti.com> Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Jeroen Hofstee [Sat, 21 Dec 2013 17:06:33 +0000 (18:06 +0100)]
ARM: twister: add missing gpio clock init
Commit f33b9bd3984fb11e1d8566a866adc5957b1e1c9d breaks boards
which do not explicitly enable the gpio clocks. This causes
the twister spl to hang, since it uses the no longer enabled
gpio 55. Add CONFIG_OMAP3_GPIO_2 to unbrick the board.
Jeroen Hofstee [Sat, 21 Dec 2013 17:03:09 +0000 (18:03 +0100)]
ARM: tam3517-common: fix nand spl boot
commit f9095aac793aa8917ab9b915c5d449e6dc8d3d30, "mtd: nand:
omap: add CONFIG_NAND_OMAP_ECCSCHEME for selection of ecc-scheme"
removed CONFIG_SPL_NAND_SOFTECC from the tam3517 common config,
causing the spl nand boot to fail. Add it back, so derived
boards boot again.
projects / u-boot.git / log