Gunnar Rangoy [Fri, 23 Jan 2009 11:56:31 +0000 (12:56 +0100)]
AVR32: macb - Search for PHY id
This patch adds support for searching through available PHY-addresses in
the macb-driver. This is needed for the ATEVK1100 evaluation board,
where the PHY-address will be initialized to either 1 or 7.
This patch adds a config option, CONFIG_MACB_SEARCH_PHY, which when
enabled tells the driver to search for the PHY address.
Signed-off-by: Gunnar Rangoy <gunnar@rangoy.com> Signed-off-by: Paul Driveklepp <pauldriveklepp@gmail.com> Signed-off-by: Olav Morken <olavmrk@gmail.com> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Due to a bug, avr32-gcc will assume that ip is aligned on a word boundary when
using volatile, which causes an exception since xip isn't aligned on a word
boundary.
Signed-off-by: Gunnar Rangoy <gunnar@rangoy.com> Signed-off-by: Paul Driveklepp <pauldriveklepp@gmail.com> Signed-off-by: Olav Morken <olavmrk@gmail.com> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Mike Frysinger [Wed, 28 Jan 2009 18:48:55 +0000 (13:48 -0500)]
SPD823TS: do not define CONFIG_CMD_ENV
Since the SPD823TS board does not actually have any writable flash to save
its environment, undefine CONFIG_CMD_ENV so the "saveenv" command is
disabled.
This fixes the build error:
common/libcommon.a(cmd_nvedit.o): In function `do_saveenv':
common/cmd_nvedit.c:557: undefined reference to `saveenv'
make: *** [u-boot] Error 1
Kumar Gala [Wed, 28 Jan 2009 14:31:10 +0000 (08:31 -0600)]
85xx: Fix compile breakage with MPC8540EVAL
Configuring for MPC8540EVAL board...
mpc8540eval.c: In function 'checkboard':
mpc8540eval.c:53: error: invalid operands to binary /
make[1]: *** [mpc8540eval.o] Error 1
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Bryan Wu [Mon, 19 Jan 2009 04:04:27 +0000 (23:04 -0500)]
usb_scan_devices: fix output with no devices
We should check the return of usb_new_device() so that if no USB device is
found, we print out the right message rather than always saying "new usb
device found".
Stefan Roese [Wed, 21 Jan 2009 16:12:19 +0000 (17:12 +0100)]
USB: Add dcache support to the EHCI driver
This patch adds routines to handle (flush/invalidate) the dcache for the
QH and qTD structures and data buffers. This is needed on platforms using
this EHCI support with dcache enabled (like the MIPS VCT board port).
Signed-off-by: Stefan Roese <sr@denx.de> Signed-off-by: Remy Bohmer <linux@bohmer.net>
Stefan Roese [Wed, 21 Jan 2009 16:12:10 +0000 (17:12 +0100)]
USB: Add config option to call ehci_hcd_init() again after EHCI reset
This patch adds the config option CONFIG_EHCI_HCD_INIT_AFTER_RESET
to call ehci_hcd_init() again after ehci_reset() is executed. This
is needed for the upcoming VCT EHCI support which needs to re-init
the hcd part again after the EHCI CMD_RESET is executed.
Signed-off-by: Stefan Roese <sr@denx.de> Signed-off-by: Remy Bohmer <linux@bohmer.net>
Stefan Roese [Wed, 21 Jan 2009 16:12:01 +0000 (17:12 +0100)]
USB: Fix speed detection on EHCI cntr with root hub transaction translators
This patch fixes an issue that the speed of USB devices was not detected
correctly on some EHCI controllers. This will be used on the upcoming VCT
EHCI support.
Signed-off-by: Stefan Roese <sr@denx.de> Signed-off-by: Remy Bohmer <linux@bohmer.net>
Mike Frysinger [Thu, 1 Jan 2009 23:27:27 +0000 (18:27 -0500)]
usb.h: use standard __LITTLE_ENDIAN from Linux headers
Rather than forcing people to define a custom "LITTLEENDIAN", just use the
__LITTLE_ENDIAN one from the Linux byteorder headers that every arch is
already setting up.
Signed-off-by: Mike Frysinger <vapier@gentoo.org> Signed-off-by: Remy Bohmer <linux@bohmer.net>
Thomas Abraham [Sun, 4 Jan 2009 06:45:35 +0000 (12:15 +0530)]
usb : usb_kbd : Populating 'priv' member of USB keyboard device_t structure
This patch populates the 'priv' field of the USB keyboard device_t
structure. The 'priv' field is populated with the address of the
'struct usb_device' structure that represents the USB device.
The 'priv' field can then be used in the 'usb_event_poll' function to
determine the USB device that requires to be polled. An
example of its usage in 'usb_event_poll' function is as below.
michael [Thu, 11 Dec 2008 12:43:55 +0000 (13:43 +0100)]
[PATCH] This patch add varius fix to the ehci.
- fix ehci_readl, ehci_writel
- introduce new define in ehci.h
- introduce the handshake function for waiting on a register
- fix usb_ehci_fsl with the new HC_LENGTH macro
Signed-off-by: Michael Trimarchi <trimarchimichael@yahoo.it> Signed-off-by: Remy Böhmer <linux@bohmer.net>
michael [Wed, 10 Dec 2008 16:55:19 +0000 (17:55 +0100)]
[PATCH] Fix EHCI usb. I start to test on a
IXP465 board and I find some errors in the code. This
patch fix:
- descriptor initizialization (config, interface and endpoint
must be one next-to the other when the USB_DT_CONFIG message
is send.
- FIX little/endian bigendian (introduce the CONFIG_EHCI_DESC_BIG_ENDIAN
and the CONFIG_EHCI_MMIO_BIG_ENDIAN)
- Introduce the linux version of the usb_config_descriptor and
usb_interface descriptor. This descriptor does't contains
u-boot extension.
Signed-off-by: Michael Trimarchi <trimarchimichael@yahoo.it> Signed-off-by: Remy Böhmer <linux@bohmer.net>
Mike Frysinger [Sun, 12 Oct 2008 02:05:42 +0000 (22:05 -0400)]
Blackfin: implement real write support for OTP
Now that real documentation has been released for the OTP interface and
the on-chip ROM wrt writing/timings, implement support for reading/writing
as well as dumping/locking.
Mike Frysinger [Sun, 1 Jun 2008 05:26:29 +0000 (01:26 -0400)]
Blackfin: respect CONFIG_CLKIN_HALF
As pointed out by Ivan Koryakovskiy, the initialization code was not
actually respecting the CONFIG_CLKIN_HALF option when configuring the
PLL_CTL register.
Mike Frysinger [Sun, 12 Oct 2008 00:30:28 +0000 (20:30 -0400)]
Blackfin: bf533-ezkit: shuffle flash defines a little
Some of the flash defines weren't in the correct location and caused build
problems in some configurations, so let's move types and defines to better
local locations.
Mike Frysinger [Mon, 6 Oct 2008 08:16:47 +0000 (04:16 -0400)]
Blackfin: overhaul i2c driver
The current Blackfin i2c driver does not work properly with certain devices
due to it breaking up transfers incorrectly. This is a rewrite of the
driver and relocates it to the newer place in the source tree.
Also remove duplicated I2C speed defines in Blackfin board configs and
disable I2C slave address usage since it isn't implemented.
Mike Frysinger [Mon, 6 Oct 2008 07:35:44 +0000 (03:35 -0400)]
Blackfin: fix dcache handling when doing dma memcpy's
Our dcache invalidate function doesn't just invalidate, it also flushes.
So rename the function accordingly and fix the dma_memcpy() function so it
doesn't inadvertently corrupt the data destination.
Kim Phillips [Tue, 27 Jan 2009 22:03:53 +0000 (16:03 -0600)]
mpc83xx: fix undefined reference to `flush_cache' error in simpc8313 build
extend commit c70564e6b1bd08f3230182392238907f3531a87e
"NAND: Fix cache and memory inconsistency issue" to add the cache.o dependency
to the simpc8313 build and fix this:
...Large Page NAND...Configuring for SIMPC8313 board...
nand_boot_fsl_elbc.o: In function `nand_boot':
nand_spl/board/sheldon/simpc8313/nand_boot_fsl_elbc.c:150: undefined reference to `flush_cache'
make[1]: *** [/home/r1aaha/git/u-boot-mpc83xx/nand_spl/u-boot-spl] Error 1
make: *** [nand_spl] Error 2
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
projects / u-boot.git / log