riscv: booti: do not force relocation if force_reloc is not set
If force_reloc flag is not set and booti is called for an address
ouside RAM (i. e. QSPI NOR flash), we should honor that and not try
to force relocation in a bogus fashion.
Signed-off-by: Vitaly Wool <vitaly.wool@konsulko.com> Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Zong Li [Fri, 9 Jul 2021 08:26:35 +0000 (16:26 +0800)]
board: sifive: remove the command for setting serial number
We wouldn't like to allow user to change the serial number, so remove
the command for changing serial number in EEPROM.
Signed-off-by: Zong Li <zong.li@sifive.com> Suggested-by: David Abdurachmanov <david.abdurachmanov@sifive.com> Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Filter out dmas dma-names interrupt-parent interrupts interrupts-extended
interrupt-names interrupt-map interrupt-map-mask iommus DT properties on
R-Car Gen3, since they are not used by U-Boot and only take space.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Marek Vasut [Sat, 10 Jul 2021 16:56:29 +0000 (18:56 +0200)]
ARM: dts: rmobile: Disable RPC HF by default
The RPC HF might be locked by ATF, and any access to its register
space would result in complete hang. Disable the RPC HF by default.
The ATF should be patched to set RPC node status = "okay" in the DT
fragment it passes to U-Boot in case the RPC HF access is unlocked,
and that way U-Boot could access the RPC HF safely.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Marek Vasut [Sun, 4 Jul 2021 15:27:27 +0000 (17:27 +0200)]
ARM: rmobile: Align CPU: print with other prints
The CPU: print only has one space after it, while the other prints
from U-Boot align the value to offset 7. Align the CPU: print too.
No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Marek Vasut [Sat, 3 Jul 2021 18:41:50 +0000 (20:41 +0200)]
ARM: rmobile: Enable sysinfo on R-Car Gen3
Enable support for sysinfo on supported R-Car Gen3 boards. The sysinfo
is used e.g. to access and decode board-specific information and then
in turn used by board-info to print those information. On R-Car Gen3
the sysinfo rcar3 driver is used to parse the board ID EEPROM, obtain
board type and revision from it, and let board-info print this
information on boot.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Marek Vasut [Sat, 3 Jul 2021 16:16:14 +0000 (18:16 +0200)]
ARM: dts: rmobile: Add sysinfo extras on R-Car Gen3
Add sysinfo node and phandle to the board ID EEPROM on all boards
where this functionality is described in DT, which is Salvator-X(S),
ULCB and Ebisu. The u-boot,dm-pre-reloc is necessary here, since the
sysinfo must be available early during boot. The V3M and V3H boards
currently do not describe this board ID EEPROM in upstream DT, but
that could be easily added later, once the DTs contain the necessary
nodes.
ULCB and Ebisu needs the full EEPROM node in the u-boot extras DT,
since the EEPROM node is still missing in the upstream DTs. Ebisu
also needs extra compatible string override for the i2c_dvfs.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
The Renesas R-Car Gen3 development kits contain board ID EEPROM.
This driver parses out the board ID and revision out of that
EEPROM and exports it e.g. for the board-info print on boot.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Sean Anderson <sean.anderson@seco.com> Cc: Simon Glass <sjg@chromium.org>
- Marvell SheevaPlug: Convert Ethernet and SATA to Driver Model (Tony)
- Zyxel NSA310S NAS: Convert to Driver Model (Tony)
- Turris_omnia: Add `u-boot-env` NOR partition (Marek)
- Turris_omnia: Fixup MTD partitions in Linux' DTB (Marek)
- Espressobin: Enable 'mtd' command and define SPI NOR partitions (Pali)
Tom Rini [Mon, 19 Jul 2021 12:29:24 +0000 (08:29 -0400)]
Merge tag 'ti-v2021.10-rc1' of https://source.denx.de/u-boot/custodians/u-boot-ti
- Enabled distro boot for all TI platforms.
- Cleanup for AM335x Guardian Board
- PRUSS rproc on AM65 platform.
- Add PMIC support for J7200
- Misc fixes for Nokia RX-51
arm: mvebu: Espressobin: Enable 'mtd' command and define SPI NOR partitions
U-Boot now supports parsing SPI NOR partitions from Device Tree. So enable
'mtd' command support for Espressobin board and define partition layout in
U-Boot Espressobin DTS file. Access to SPI NOR via 'sf' command is old
method and 'mtd' command is now preferred variant.
From include file remove '#define CONFIG_MTD_PARTITIONS' as this option is
now defined and enabled in defconfig file. This change is required to fix
compile error:
CC arch/arm/lib/asm-offsets.s
In file included from include/config.h:4,
from include/common.h:16,
from lib/asm-offsets.c:14:
include/configs/mvebu_armada-37xx.h:63: warning: "CONFIG_MTD_PARTITIONS" redefined
#define CONFIG_MTD_PARTITIONS /* required for UBI partition support */
In file included from ././include/linux/kconfig.h:4,
from <command-line>:
include/generated/autoconf.h:44: note: this is the location of the previous definition
#define CONFIG_MTD_PARTITIONS 1
After enabling support for mtd command, output from 'mtd list' on
Espressobin board is:
=> mtd list
List of MTD devices:
* w25q32dw
- device: spi-flash@0
- parent: spi@10600
- driver: jedec_spi_nor
- path: /soc/internal-regs/spi@10600/spi-flash@0
- type: NOR flash
- block size: 0x1000 bytes
- min I/O: 0x1 bytes
- 0x000000000000-0x000000400000 : "w25q32dw"
- 0x000000000000-0x0000003f0000 : "firmware"
- 0x0000003f0000-0x000000400000 : "u-boot-env"
=>
Signed-off-by: Pali Rohár <pali@kernel.org> Reviewed-by: Konstantin Porotchkin <kostap@marvell.com> Reviewed-by: Stefan Roese <sr@denx.de>
Marek Behún [Thu, 15 Jul 2021 17:21:02 +0000 (19:21 +0200)]
arm: mvebu: turris_omnia: fixup MTD partitions in Linux' DTB
Fixup SPI NOR partition nodes in Linux' device tree prior booting Linux.
Linux' devicetree does not contain "u-boot-env" partition and we do not
want to add it there because the address is different between stock
U-Boot and current upstream U-Boot.
Instead we add code that recreates partition nodes from scratch
according to how U-Boot sees them (which is defined in U-Boot's device
tree).
Signed-off-by: Marek Behún <marek.behun@nic.cz> Reviewed-by: Stefan Roese <sr@denx.de>
Marek Behún [Thu, 15 Jul 2021 17:21:01 +0000 (19:21 +0200)]
ARM: dts: armada-385-turris-omnia: add `u-boot-env` NOR partition
Specify a separate partition `u-boot-env` for U-Boot's env settings for
the Turris Omnia board.
Do this only in U-Boot's specific DTS. We do not want to do this in
Linux' official DTS, because Omnia's stock U-Boot stores env at a
different address, and there are still boards with stock U-Boot.
In a subsequent patch will add board code that fixes Linux's DTB before
booting Linux.
Signed-off-by: Marek Behún <marek.behun@nic.cz> Reviewed-by: Stefan Roese <sr@denx.de>
Tony Dinh [Fri, 16 Jul 2021 09:18:04 +0000 (02:18 -0700)]
arm: kirkwood: Marvell Sheevaplug: Use Ethernet PHY name and address from device tree
- In DM Ethernet, the old "egiga0" name is no longer valid, so replace it
with Ethernet PHY name from device tree. Also, Ethernet PHY address
is available so read it from device tree.
Tony Dinh [Wed, 7 Jul 2021 09:06:47 +0000 (02:06 -0700)]
arm: kirkwood: NSA310S: Use Ethernet PHY name from device tree
In DM Ethernet, the old "egiga0" name is no longer valid, so replace it
with Ethernet PHY name from device tree. Also, Ethernet PHY address
is available so read it from device tree.
Tony Dinh [Thu, 1 Jul 2021 04:26:23 +0000 (21:26 -0700)]
arm: kirkwood: NSA310S: Add DM USB, DM Ethernet, and DM SATA configs
Convert to Driver Model.
- Add DM USB, DM Ethernet, and DM SATA configs to nsa310s_defconfig
- Add CONFIG_DEFAULT_DEVICE_TREE to nsa310s_defconfig
- Move CONFIG_ENV_SECT_SIZE from board file to nsa310s_defconfig
- Add CONFIG_IDENT_STRING, and CONFIG_NET_RANDOM_ETHADDR
to nsa310s_defconfig
Signed-off-by: Tony Dinh <mibodhi@gmail.com> Reviewed-by: Stefan Roese <sr@denx.de>
Tom Rini [Mon, 19 Jul 2021 03:07:36 +0000 (23:07 -0400)]
Merge branch '2021-07-18-finalize-migrations'
- With the deadline for DM_USB (host controller support), DM_VIDEO,
DM_SPI_FLASH and DM_PCI now at 2 years past the release where their
migration deadline was given, finish removing platforms and enforcing
the switch.
Tom Rini [Fri, 9 Jul 2021 14:11:56 +0000 (10:11 -0400)]
usb: Enforce DM_USB migration for USB_HOST devices.
As the deadline for migration to DM_USB, when using a USB host
controller has now gone two years past the deadline, enforce migration.
This is done by:
- Ensuring that all host controller options (other than the very legacy
old MUSB ones) now select USB_HOST. USB_HOST now enforces DM_USB and
OF_CONTROL.
- Remove other parts of Kconfig logic that had platforms pick DM_USB.
- To keep Kconfig happy, have some select statements test for USB_HOST
as well.
- Re-order some Kconfig entries and menus so that we can cleanly pick
host or gadget roles. For the various HCD options that have platform
glue options, group them together and update dependencies in some
cases.
- As SPL_DM_USB is not required, on platforms that had not yet enabled
it, disable it.
Cc: Marek Vasut <marex@denx.de> Cc: Icenowy Zheng <icenowy@aosc.io> Cc: Samuel Holland <samuel@sholland.org> Cc: FUKAUMI Naoki <naobsd@gmail.com> Cc: Andre Przywara <andre.przywara@arm.com> Cc: Jagan Teki <jagan@amarulasolutions.com> Signed-off-by: Tom Rini <trini@konsulko.com>
Tom Rini [Fri, 9 Jul 2021 14:11:55 +0000 (10:11 -0400)]
treewide: Test on CONFIG_USB_HOST (or CONFIG_CMD_USB) not CONFIG_USB
As the logic here is only used when we have a USB host controller, test
on CONFIG_USB_HOST rather than CONFIG_USB in general. This lets us move
towards using CONFIG_USB only as a menu symbol to say that we have some
form of USB, and then USB_HOST or USB_GADGET depending on the role that
USB plays within the build.
Tom Rini [Fri, 9 Jul 2021 14:11:54 +0000 (10:11 -0400)]
tegra: Test on CONFIG_CMD_USB being enabled for distro bootcmd
Reuse the common logic to allow for BOOT_TARGET_DEVICES to list USB as a
possibility if we're building for a platform that will have USB but not
if we don't, so that we don't hit the link-time check for trying to have
USB boot on a non-USB system.
Acked-by: Tom Warren <twarren@nvidia.com> Signed-off-by: Tom Rini <trini@konsulko.com>
Tom Rini [Fri, 9 Jul 2021 14:11:53 +0000 (10:11 -0400)]
ge_bx50v3: Remove unused USB related defines
These USB defines do not change the build as there is no USB support
enabled currently.
Cc: Ian Ray <ian.ray@ge.com> Cc: Sebastian Reichel <sebastian.reichel@collabora.com> Signed-off-by: Tom Rini <trini@konsulko.com> Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Tom Rini [Mon, 12 Jul 2021 16:42:10 +0000 (12:42 -0400)]
vinco: Enable DM_USB and DM_SPI_FLASH support
As this platform already enables CONFIG_DM and CONFIG_OF_CONTROL,
migrating to DM_USB and DM_SPI_FLASH is just a matter of enabling the
correct options.
Cc: Gregory CLEMENT <gregory.clement@bootlin.com>
u-boot@lists.denx.de (open list) Reported-by: Marek Behun <marek.behun@nic.cz> Signed-off-by: Tom Rini <trini@konsulko.com>
As almost all peripherals are connected via PCI dependent on the
used core card, PCI setup is always required. Thus run pci_init()
including PCI scanning and probing and core card specific setups
in board_early_init_r().
Also prepare support for dynamically managing the status of the
different PCI DT nodes dependent on used core card via option
CONFIG_OF_BOARD_FIXUP. Before this feature can be enabled,
the call order of the fix_fdt() init hook in board_init_f
needs to be changed. Otherwise rw_fdt_blob points to a read-only
NOR flash address. Thus this options needs to stay disabled
until the board_init_f problem could be solved. This breaks
running the default U-Boot image on real HW using the FPGA core
card but Qemu emulation still works. Currently Qemu is more
important as MIPS CI tests depend on Malta and the deadline
for PCI DM conversion will be enforced soon.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
MIPS: malta: add DT bindings for PCI host controller
Add DT binding for GT64120 and MSC01 PCI controllers. Only
GT64120 is enabled by default to support Qemu. The MSC01 node
will be dynamically enabled by Malta board code dependent
on the plugged core card.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
dm: pci: add option to map virtual system memory base address
On MIPS the DRAM start address respectively CONFIG_SYS_SDRAM_BASE
is still used as a virtual, CPU-mapped address instead of being used
as physical address. Converting all MIPS boards and generic MIPS code
to fix that is not trivial. Due to the approaching deadline for
PCI DM conversion, this workaround is required for MIPS boards with
PCI support until the CONFIG_SYS_SDRAM_BASE issue could be solved.
Add a compile-time option to let the PCI uclass core optionally map
the DRAM address to a physical address when adding the PCI region
of type PCI_REGION_SYS_MEMORY.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com> Reviewed-by: Stefan Roese <sr@denx.de>
Tom Rini [Sun, 18 Jul 2021 15:03:02 +0000 (11:03 -0400)]
Merge tag 'efi-2021-10-rc1-2' of https://source.denx.de/u-boot/custodians/u-boot-efi
Pull request for efi-2021-10-rc1-2
* Correct device path nodes for GUID partitions
* Embed keys to check update capsules instead of providing then in DTB
* Increase event log buffer size for measured boot.
Since we removed embeddingg the capsule key into a .dtb and fixed
authenticated capsule updates for all boards, move the relevant
documentation in the efi file and update it accordingly
commit 322c813f4bec ("mkeficapsule: Add support for embedding public key in a dtb")
added a bunch of options enabling the addition of the capsule public key
in a dtb. Since now we embedded the key in U-Boot's .rodata we don't this
this functionality anymore
The capsule signature is now part of our DTB. This is problematic when a
user is allowed to change/fixup that DTB from U-Boots command line since he
can overwrite the signature as well.
So Instead of adding the key on the DTB, embed it in the u-boot binary it
self as part of it's .rodata. This assumes that the U-Boot binary we load
is authenticated by a previous boot stage loader.
Masahisa Kojima [Wed, 14 Jul 2021 13:00:01 +0000 (22:00 +0900)]
efi_loader: increase eventlog buffer size
TCG PC Client PFP spec says "The Log Area Minimum Length
for the TCG event log MUST be at least 64KB." in ACPI chapter.
This commit increase the buffer size to 64KB.
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org> Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
efi_loader: Use %pD to log device-path instead of local efi_dp_str()
Use %pD to log device-path instead of using efi_dp_str() and
efi_free_pool() locally in find_boot_device().
This is a cleanup patch, no feature update nor fix.
Suggested-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Signed-off-by: Masami Hiramatsu <masami.hiramatsu@linaro.org> Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
efi_loader: set partition GUID in device path for SIG_TYPE_GUID
Previously, the GPT device GUID was being used instead of the partition,
which was incorrect.
Signed-off-by: Alfonso Sánchez-Beato <alfonso.sanchez-beato@canonical.com>
Let EFI_LOADER select CONFIG_PARTITION_UUIDS.
Use log_warning() instead of printf() for warning. Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Breno Lima [Tue, 29 Jun 2021 02:32:35 +0000 (10:32 +0800)]
mx7ulp: wdog: Wait for WDOG unlock and reconfiguration to complete
According to i.MX7ULP Reference Manual we should wait for WDOG unlock
and reconfiguration to complete.
Section "59.5.3 Configure Watchdog" provides the following example:
DisableInterrupts; //disable global interrupt
WDOG_CNT = 0xD928C520; //unlock watchdog
while(WDOG_CS[ULK]==0); //wait until registers are unlocked
WDOG_TOVAL = 256; //set timeout value
WDOG_CS = WDOG_CS_EN(1) | WDOG_CS_CLK(1) | WDOG_CS_INT(1) |
WDOG_CS_WIN(0) | WDOG_CS_UPDATE(1);
while(WDOG_CS[RCS]==0); //wait until new configuration takes effect
EnableInterrupts; //enable global interrupt
Update U-Boot WDOG driver to align with i.MX7ULP reference manual.
Use 32 bits accessing to CS register. According to RM, the bits in
this register only can write once after unlock. So using 8 bits access
will cause problem.
Reviewed-by: Ye Li <ye.li@nxp.com> Signed-off-by: Breno Lima <breno.lima@nxp.com> Signed-off-by: Peng Fan <peng.fan@nxp.com>
Breno Lima [Tue, 29 Jun 2021 02:32:34 +0000 (10:32 +0800)]
mx7ulp: Update unlock and refresh sequences in sWDOG driver
According to i.MX7ULP Reference Manual the second word write for both
UNLOCK and REFRESH operations must occur in maximum 16 bus clock.
The current code is using writel() function which has a DMB barrier to
order the memory access. The DMB between two words write may introduce
some delay in certain circumstance, causing a WDOG timeout due to 16 bus
clock window requirement.
Replace writel() function by __raw_writel() to achieve a faster memory
access and avoid such issue.
Reviewed-by: Ye Li <ye.li@nxp.com> Signed-off-by: Breno Lima <breno.lima@nxp.com>
tools: Use a single target-independent config to enable OpenSSL
Host tool features, such as mkimage's ability to sign FIT images were
enabled or disabled based on the target configuration. However, this
misses the point of a target-agnostic host tool.
A target's ability to verify FIT signatures is independent of
mkimage's ability to create those signatures. In fact, u-boot's build
system doesn't sign images. The target code can be successfully built
without relying on any ability to sign such code.
Conversely, mkimage's ability to sign images does not require that
those images will only work on targets which support FIT verification.
Linking mkimage cryptographic features to target support for FIT
verification is misguided.
Without loss of generality, we can say that host features are and
should be independent of target features.
While we prefer that a host tool always supports the same feature set,
we recognize the following
- some users prefer to build u-boot without a dependency on OpenSSL.
- some distros prefer to ship mkimage without linking to OpenSSL
To allow these use cases, introduce a host-only Kconfig which is used
to select or deselect libcrypto support. Some mkimage features or some
host tools might not be available, but this shouldn't affect the
u-boot build.
I also considered setting the default of this config based on
FIT_SIGNATURE. While it would preserve the old behaviour it's also
contrary to the goals of this change. I decided to enable it by
default, so that the default build yields the most feature-complete
mkimage.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
image: Add support for relocating crypto_algos in linker lists
Function pointers from crypto_algos array are relocated, when
NEEDS_MANUAL_RELOC is set. This relocation doesn't happen if the algo
is placed in a linker list. Implement this relocation.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org> Acked-by: Michal Simek <michal.simek@xilinx.com>
It is no longer necessary to implement rsa_() functions as no-ops
depending on config options. It is merely sufficient to provide the
prototypes, as the rsa code is no longer linked when unused.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
It is no longer necessary to implement ecdsa_() functions as no-ops
depending on config options. It is merely sufficient to provide the
prototypes, as the ecdsa code is no longer linked when unused.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
image: rsa: Move verification algorithm to a linker list
Move the RSA verification crytpo_algo structure out of the
crypto_algos array, and into a linker list.
Although it appears we are adding an #ifdef to rsa-verify.c, the gains
outweigh this small inconvenience. This is because rsa_verify() is
defined differently based on #ifdefs. This change allows us to have
a single definition of rsa_verify().
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
image: Add support for placing crypto_algo in linker lists
The purpose of this change is to enable crypto algorithms to be placed
in linker lists, rather than be declared as a static array. The goal
is to remove the crypto_algos array in a subsequent patch.
Create a new linker list named "cryptos", and search it when
image_get_crypto_algo() is invoked.
NOTE that adding support for manual relocation of crypto_algos within
linker lists is beyond the scope of this patch.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
common: image-sig.c: Remove host-specific logic and #ifdefs
Remove any ifdefs in image-sig.c that were previously used to
differentiate from the host code. Note that all code dedicated to
relocating ->sign() and ->add_verify_data)_ can be safely removed,
as signing is not supported target-side.
NOTE that although it appears we are removing ecdsa256 support, this
is intentional. ecdsa_verify() is a no-op on the target, and is
currently only used by host code.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
common: Move host-only logic in image-sig.c to separate file
image-sig.c is used to map a hash or crypto algorithm name to a
handler of that algorithm. There is some similarity between the host
and target variants, with the differences worked out by #ifdefs. The
purpose of this change is to remove those ifdefs.
First, copy the file to a host-only version, and remove target
specific code. Although it looks like we are duplicating code,
subsequent patches will change the way target algorithms are searched.
Besides we are only duplicating three string to struct mapping
functions. This isn't something to fuss about.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Simon Glass [Wed, 14 Jul 2021 22:05:36 +0000 (17:05 -0500)]
image: Drop IMAGE_ENABLE_BEST_MATCH
This is not needed with Kconfig, since we can use IS_ENABLED() easily
enough. Drop it.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com> Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Simon Glass [Wed, 14 Jul 2021 22:05:35 +0000 (17:05 -0500)]
image: Drop IMAGE_ENABLE_SHAxxx
We already have a host Kconfig for these SHA options. Use
CONFIG_IS_ENABLED(SHAxxx) directly in the code shared with the host build,
so we can drop the unnecessary indirections.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com> Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Simon Glass [Wed, 14 Jul 2021 22:05:34 +0000 (17:05 -0500)]
image: Drop IMAGE_ENABLE_SHA1
We already have a host Kconfig for SHA1. Use CONFIG_IS_ENABLED(SHA1)
directly in the code shared with the host build, so we can drop the
unnecessary indirection.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com> Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Simon Glass [Wed, 14 Jul 2021 22:05:33 +0000 (17:05 -0500)]
Kconfig: Rename SPL_MD5_SUPPORT to SPL_MD5
Drop the _SUPPORT suffix so we can use CONFIG_IS_ENABLED() with this
option.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com> Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Simon Glass [Wed, 14 Jul 2021 22:05:32 +0000 (17:05 -0500)]
Kconfig: Rename SPL_CRC32_SUPPORT to SPL_CRC32
Drop the _SUPPORT suffix so we can use CONFIG_IS_ENABLED() with this
option.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com> Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Drop the ENABLE and SUPPORT parts of this, which are redundant.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com> Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Simon Glass [Wed, 14 Jul 2021 22:05:30 +0000 (17:05 -0500)]
image: Rename SPL_SHAxxx_SUPPORT to SPL_FIT_SHAxxx
These option are named inconsistently with other SPL options, thus making
them incompatible with the CONFIG_IS_ENABLED() macro. Rename them.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com> Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Simon Glass [Wed, 14 Jul 2021 22:05:29 +0000 (17:05 -0500)]
image: Shorten FIT_ENABLE_SHAxxx_SUPPORT
The ENABLE part of this name is redundant, since all boolean Kconfig
options serve to enable something. The SUPPORT part is also redundant
since Kconfigs can be assumed to enable support for something. Together
they just serve to make these options overly long and inconsistent
with other options.
Rename FIT_ENABLE_SHAxxx_SUPPORT to FIT_SHAxxx
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com> Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
drivers: watchdog: wdt-uclass: Use IS_ENABLED for WATCHDOG_AUTOSTART
There is no separate SPL/TPL config for WATCHDOG_AUTOSTART.
So use IS_ENABLED instead of CONFIG_IS_ENABLED to make watchdog
working in SPL again.
Fixes: 830d29ac3721 ("watchdog: Allow to use CONFIG_WDT without starting watchdog") Signed-off-by: Teresa Remmet <t.remmet@phytec.de> Reviewed-by: Stefan Roese <sr@denx.de>
MengLi [Mon, 24 May 2021 02:22:48 +0000 (10:22 +0800)]
driver: watchdog: reset watchdog in designware_wdt_stop() function
In uboot command line environment, watchdog is not able to be
stopped with below commands:
SOCFPGA_STRATIX10 # wdt dev watchdog@ffd00200
SOCFPGA_STRATIX10 # wdt stop
Refer to watchdog driver in linux kernel, it is also need to reset
watchdog after disable it so that the disable action takes effect.
Signed-off-by: Meng Li <Meng.Li@windriver.com> Reviewed-by: Stefan Roese <sr@denx.de> Reviewed-by: Sean Anderson <sean.anderson@seco.com>
stm32mp: use device sequence number in boot_instance variable
Use the device sequence number in boot_instance variable
and no more the SDMMC instance provided by ROM code/TF-A.
After this patch we don't need to define the mmc alias in
device tree, for example:
mmc0 = &sdmmc1;
mmc1 = &sdmmc2;
mmc2 = &sdmmc3;
to have a correct mapping between the ROM code boot device =
"${boot_device}${boot_instance}" and the MMC device in U-Boot.
With this patch the 'mmc0' device (used in mmc commands) is
always used when only one instance sdmmc is activated in device
tree, even if it is only the sdmmc2 or sdmmc3.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com> Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Patrick Delaunay [Tue, 29 Jun 2021 10:01:07 +0000 (12:01 +0200)]
arm: dts: stm32mp15: alignment with v5.13
Device tree alignment with Linux kernel v5.13
- ARM: dts: stm32: Add PTP clock to Ethernet controller
- ARM: dts: stm32: enable the analog filter for all I2C nodes in
stm32mp151
- ARM: dts: stm32: fix usart 2 & 3 pinconf to wake up with flow control
- ARM: dts: stm32: Add wakeup management on stm32mp15x UART nodes
- ARM: dts: stm32: add #clock-cells property to usbphyc node on stm32mp151
- ARM: dts: stm32: Add STM32MP1 I2C6 SDA/SCL pinmux
- ARM: dts: stm32: Rename mmc controller nodes to mmc@
- ARM: dts: stm32: Add additional init state for SDMMC1 pins
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com> Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Patrick Delaunay [Mon, 28 Jun 2021 12:56:03 +0000 (14:56 +0200)]
stm32mp: cmd_stm32key: add subcommand close
The expected sequence to close the device
1/ Load key in DDR with any supported load command
2/ Update OTP with key: STM32MP> stm32key read <addr>
At this point the device is able to perform image authentication but
non-authenticated images can still be used and executed.
So it is the last moment to test boot with signed binary and
check that the ROM code accepts them.
3/ Close the device: only signed binary will be accepted !!
STM32MP> stm32key close
Warning: Programming these OTP is an irreversible operation!
This may brick your system if the HASH of key is invalid
This command should be deactivated by default in real product.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com> Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Patrick Delaunay [Mon, 28 Jun 2021 12:56:00 +0000 (14:56 +0200)]
stm32mp: cmd_stm32key: lock of PKH OTP after fuse
Lock the OTP value of key's hash after the command
$> stm32key fuse <address>
This operation forbids a second update of these OTP as they are
ECC protected in BSEC: any update of these OTP with a different value
causes a BSEC disturb error and the closed chip will be bricked.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com> Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Patrick Delaunay [Mon, 28 Jun 2021 12:44:33 +0000 (14:44 +0200)]
stm32mp: stm32prog: fix the content of short help message
Reduce the content of short help message for stm32prog command and
removed the carriage return to fix the display of 'help' command when
this command is activated.
Fixes: 954bd1a923a6 ("stm32mp: add the command stm32prog") Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Patrick Delaunay [Mon, 28 Jun 2021 12:42:08 +0000 (14:42 +0200)]
configs: stm32mp1: remove splashimage and add fdtoverlay_addr_r
Add the variable used by PXE command for fdtoverlays support
since the commit 69076dff2284 ("cmd: pxe: add support for FDT overlays").
Reused the unused "splashimage" address as CONFIG_SPLASH_SOURCE and
CONFIG_VIDEO_LOGO are not activated and U-Boot display the "BACKGROUND"
image found in extlinux.conf to manage splashscreen on stm32mp1 boards.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com> Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Stephan Gerhold [Thu, 1 Jul 2021 18:33:16 +0000 (20:33 +0200)]
image: android: Automatically detect more compression types
At the moment android_image_get_kcomp() can automatically detect
LZ4 compressed kernels and the compression specified in uImages.
However, especially on ARM64 Linux is often compressed with GZIP.
Attempting to boot an Android image with a GZIP compressed kernel
image currently results in a very strange crash, e.g.
Note the 1f8b, which are the "magic" bytes for GZIP images.
U-Boot already has the image_decomp_type() function that checks for
the magic bytes of bzip2, gzip, lzma and lzo. It's easy to make use
of it here to increase the chance that we do the right thing and the
user does not become confused with strange crashes.
This allows booting Android boot images that contain GZIP-compressed
kernel images.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
projects / u-boot.git / log