Mingli Yu [Mon, 19 Jun 2023 06:22:50 +0000 (14:22 +0800)]
mkimage: Use PATH_MAX for path length
Fixed when build xilinx_zynqmp in long directory ( >256):
| /buildarea1/testtest/wr_build/wr1023test_secureboot/test1-what/test2-what/test3-what/test4-what/test5-what/test6-what/test7-what/test8-what/test9-what/test10-what/test11-what/test12-what/build/tmp-glibc/work/xilinx_zynqmp-wrs-linux/u-boot-xlnx/1_v2023.01-xilinx-v2023.1+gitAUTOINC+40a08d69e7-r0/build/fitImage-linux: Image file name (uboot-mkimage) too long, can't create tmpfile.
| Error: Bad parameters for FIT image type
Tom Rini [Tue, 20 Jun 2023 20:00:20 +0000 (16:00 -0400)]
doc: statistics: Re-generate the last 3 releases
With some changes to our mapping files in gitdm, re-generate the last
few releases worth of statistics to correctly reflect contributions. We
only go back this far to try and find a balance between highlighting
contributions and still being reviewable.
Simon Glass [Sat, 17 Jun 2023 10:49:48 +0000 (11:49 +0100)]
menu: Re-enable the ANSI codes
The intent here was to allow ANSI codes to be disabled, since it was
proving impoosible to test operation of the menu code when it kept moving
the cursor. Unfortunately this ended up in the patch.
Correct this by enabling ANSI again.
Signed-off-by: Simon Glass <sjg@chromium.org> Reported-by: Pali Rohár <pali@kernel.org> Reported-by: Mark Kettenis <mark.kettenis@xs4all.nl> Reported-by: Frank Wunderlich <frank-w@public-files.de> Fixes: 32bab0eae51b ("menu: Make use of CLI character processing") Tested-by: Mark Kettenis <kettenis@openbsd.org> Reviewed-by: Mark Kettenis <kettenis@openbsd.org>
Simon Glass [Fri, 23 Jun 2023 12:22:09 +0000 (13:22 +0100)]
doc: Tidy up the format docs to be more generic
Avoid reference to uImage which is the old format. Drop the historical
language at the top and rewrite a few other sections. Correct the
U-Boot filename which is now in the boot/ directory.
usb: dwc2: Fix the write to W1C fields in HPRT register
Fix the write to the HPRT register which treat W1C fields
as if they were mere RW. This leads to unintended clearing of such fields
This bug was found during the testing on Simics model. Referring to
specification DesignWare Cores USB 2.0 Hi-Speed On-The-Go (OTG)
Databook (3.30a)"5.3.4.8 Host Port Control and Status Register (HPRT)", the
HPRT.PrtPwr is cleared by this mistake. In the Linux driver (contrary to
U-Boot), HPRT is always read using dwc2_read_hprt0 helper function which
clears W1C bits. So after write back those bits are zeroes.
When bootflow scan is run, this will cause a UCLASS_BOOTDEV device to
be added as sibling of those UCLASS_BLK devices found in the search
chain defined in environment variable "boot_targets", until boot
succeeds from some device. This can happen automatically as part of
the default boot process on some boards (example: Rock Pi 4) depending
on the board configuration (DISTRO_DEFAULTS, BOOTSTD, BOOTCOMMAND,
etc.) because they have bootcmd=bootflow scan.
If boot doesn't succeed from any device, and usb is in boot_targets,
and an usb storage device is plugged to some usb port at boot time,
its UCLASS_MASS_STORAGE device will have a UCLASS_BOOTDEV device as
child, besides a UCLASS_BLK child.
If once the boot fails the user enters at the U-Boot shell prompt:
usb info
or
usb tree
The code in cmd/usb.c will eventually recurse into the UCLASS_BOOTDEV
device and pass a null usb_device pointer to usb_show_tree_graph() or
usb_show_info() (because it has no parent_priv_).
This causes a reset. The expected behaviour would be to ignore the
UCLASS_BOOTDEV device, continue listing the usb information and return
to the prompt.
Minimal test:
Another way to trigger this reset as a minimal test or on boards with
a different bootcmd would be:
- make sure "usb" is in environment variable boot_targets (might need
setenv boot_targets usb; and/or saveenv and reset), then, with a usb
storage device plugged to a usb port, run:
=> usb reset ; bootflow scan ; usb info
Solution:
Fix it (twice) by checking for null parent_priv_ and adding
UCLASS_BOOTDEV to the list of ignored class ids before the recursive
call.
This prevents the current particular problem with UCLASS_BOOTDEV, even
in case it ever gets some parent_priv_ struct which is not an
usb_device, despite being the child of a usb_device->dev. And it also
prevents possible future problems if other children are added to usb
devices that don't have parent_priv_ because they are not part of the
usb tree, just abstractions of functionality (like UCLASS_BLK and
UCLASS_BOOTDEV are now).
Signed-off-by: Xavier Drudis Ferran <xdrudis@tinet.cat> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Marek Vasut <marex@denx.de> Tested-by: Marek Vasut <marex@denx.de>
Ilias Apalodimas [Tue, 13 Jun 2023 13:23:06 +0000 (16:23 +0300)]
efi_selftests: fix protocol repeated selftesting
Running the protocols selftest more than one times fails with
=> setenv efi_selftest 'manage protocols' && bootefi selftest
Testing EFI API implementation
Selected test: 'manage protocols'
Setting up 'manage protocols'
Setting up 'manage protocols' succeeded
Executing 'manage protocols'
Executing 'manage protocols' succeeded
Tearing down 'manage protocols'
Tearing down 'manage protocols' succeeded
Summary: 0 failures
=> bootefi selftest
Testing EFI API implementation
Selected test: 'manage protocols'
Setting up 'manage protocols'
lib/efi_selftest/efi_selftest_manageprotocols.c(88):
ERROR: InstallProtocolInterface failed
lib/efi_selftest/efi_selftest.c(89):
ERROR: Setting up 'manage protocols' failed
Tearing down 'manage protocols'
Tearing down 'manage protocols' succeeded
Summary: 1 failures
The reason is that we don't set the handles to NULL after deleting and
freeing them. As a result the subsequent protocol installation will try
to use an existing handle which we just removed that from our object list.
Ilias Apalodimas [Mon, 12 Jun 2023 15:35:58 +0000 (18:35 +0300)]
efi_loader: simplify efi_disk_remove
Instead of discovering the ID of the device and call two different
functions for a block device or a partition, we can rewrite
efi_disk_remove() and handle the minor differences between the two
variants internally. As a results we can simplify efi_disk_remove()
a lot and get rid of the extra efi_disk_delete_raw/blk calls.
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
If a handle is not found, return 0 to let the device be removed.
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Running the controller selftest more than one times fails with
=> setenv efi_selftest 'controllers' && bootefi selftest
Testing EFI API implementation
Selected test: 'controllers'
Setting up 'controllers'
Setting up 'controllers' succeeded
Executing 'controllers'
Executing 'controllers' succeeded
Summary: 0 failures
=> bootefi selftest
Testing EFI API implementation
Selected test: 'controllers'
Setting up 'controllers'
lib/efi_selftest/efi_selftest_controllers.c(280):
ERROR: InstallProtocolInterface failed
lib/efi_selftest/efi_selftest.c(89):
ERROR: Setting up 'controllers' failed
Summary: 1 failures
There are multiple reason for this. We don't uninstall the binding
interface from the controller handle and we don't reset the handle
pointers either. So let's uninstall all the protocols properly and
reset the handles to NULL on setup().
While at it add a forgotten check when uninstalling protocols from the
handle_controller and make sure the number of child controllers is 0
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org> Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com> Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
On arm64 the its we use to generate the test FIT image has
arch = "arm";
We should use "arm64" here which is mapped to IH_ARCH_ARM64 via
uimage_arch[].
Fixes: 8391f955494e ("test/py: Create a test for launching UEFI binaries from FIT images") Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
On the arm64 architecture booti_setup() is called for EFI FIT images.
This function call fails because EFI images typically do not have a
kernel signature.
Check that the operating system property "os" of the image is "linux"
before invoking booti_setup().
Fixes: 487b5fa6deb1 ("bootm: Handle kernel_noload on arm64") Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Tom Rini [Wed, 14 Jun 2023 19:50:04 +0000 (15:50 -0400)]
Merge branch '2023-06-14-assorted-fixes'
- Fix some issues Coverity Scan reported in IPv6, SPL EXTn support fix,
two small bootstd fixes, one Kconfig dependency fix, and fix booting
on Pinephone Pro
Peter Robinson [Sun, 11 Jun 2023 17:18:34 +0000 (18:18 +0100)]
rockchip: Pinephone Pro: Add DDR RAM type config
Add the RAM_ROCKCHIP_LPDDR4 to fix the Pinephone Pro booting.
When the configs were updated in 26f92be07e2 it somehow broke
the PPP boot process so let's fix it.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com> CC: Jagan Teki <jagan@edgeble.ai> CC: Kever Yang <kever.yang@rock-chips.com>
Jonas Karlman [Fri, 9 Jun 2023 14:59:01 +0000 (14:59 +0000)]
bootstd: Fix relative path use in extlinux bootmeth
Using relative path in a /boot/extlinux/extlinux.conf file fails to load
linux kernel.
Using a /boot/extlinux/extlinux.conf file:
LABEL test
LINUX ../linux/Image
Result in following error:
Retrieving file: ../linux/Image
Skipping test for failure retrieving kernel
Boot failed (err=-14)
However, using sysboot cmd successfully load kernel using same file:
sysboot mmc 1:1 any ${scriptaddr} /boot/extlinux/extlinux.conf
Retrieving file: /boot/extlinux/../linux/Image
Fix relative path using bootmeth extlinux by supplying bootfile path
instead of subdir path in the call to pxe_setup_ctx, same as done in the
sysboot command.
Fixes: 31aefaf89a5b ("bootstd: Add an implementation of distro boot") Signed-off-by: Jonas Karlman <jonas@kwiboo.se> Reviewed-by: Simon Glass <sjg@chromium.org>
Simon Glass [Wed, 22 Feb 2023 21:06:23 +0000 (14:06 -0700)]
bootstd: Make BOOTSTD_FULL depend on BOOTSTD
Move BOOTSTD_FULL down in the file so that it can be enabled only when
BOOTSTD is enabled. This prevents a build error if BOOTSTD is disabled
but BOOTSTD_FULL is enabled.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Eugen Hristev [Wed, 17 May 2023 10:41:24 +0000 (13:41 +0300)]
net: rtl8169: add depends on PCI
The rtl8169 driver uses calls to dm_pci_bus_to_phys,
which are compiled under CONFIG_PCI.
Without CONFIG_PCI, this happens:
drivers/net/rtl8169.o: in function `rtl_recv_common':
drivers/net/rtl8169.c:555: undefined reference to `dm_pci_bus_to_phys'
It is only natural that this driver depends on CONFIG_PCI then.
The device does not work connected in another way anyway, and the driver
does not assume anything else at this moment.
Signed-off-by: Eugen Hristev <eugen.hristev@collabora.com> Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Since commit 9905cae65e03 ("fs: ext4: check the minimal partition size
to mount"), a valid size needs to be provided when mounting
an ext filesystem. Fix the spl ext driver to use the parition size
instead of 0 when mounting the filesystem.
Detlev Casanova [Fri, 9 Jun 2023 15:19:08 +0000 (11:19 -0400)]
renesas: rcar: Apply ATF overlay for reserved-memory
The function fdtdec_board_setup() is called early and adds the overlay
from ATF to the u-boot device tree. That is necessary so that u-boot
doesn't use reserved memory.
Linux also needs to know about that reserved memory so the overlay from
ATF needs to be aplied on the linux device tree as well.
This commit makes sure that the ATF overlay is applied to both device trees.
Signed-off-by: Detlev Casanova <detlev.casanova@collabora.com> Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org> Reviewed-by: Adam Ford <aford173@gmail.com>
Hai Pham [Tue, 4 May 2021 10:43:23 +0000 (17:43 +0700)]
ARM: rmobile: Identify R-Car D3 R8A77995 r1.1 SoC
Add support to identify R8A77995 r1.1 SoC.
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org> Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
[Marek: Slight update to commit message, spell out the SoC model]
r8a7796 cpu revision v1.2 has the same information as revision v1.1.
This patch fixes revision display at startup to "rev 1.1/1.2".
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org> Signed-off-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com> Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
[Marek: Slight update to commit message, spell out the SoC model]
Sam Edwards [Thu, 8 Jun 2023 18:45:42 +0000 (12:45 -0600)]
usb: musb-new: sunxi: remove unused define
This is a remnant from when the USB controller driver managed
the reset signal itself. A patch from the very end of 2018 changed
this driver to delegate reset (and clock) management to the proper
control unit driver, but left this unused define behind.
Signed-off-by: Sam Edwards <CFSworks@gmail.com> Reviewed-by: Marek Vasut <marex@denx.de>
A small late pull request for Allwinner. The main feature is just a DT
update, matching the v6.4 Linux kernel DT files. This also enables a
board (LCTech Pi F1C200s) which got its .dts file merged into Linux.
Plus a tiny typo fix from Sam.
Gitlab CI passed, briefly tested on an H616 board and the new LCTech Pi.
Andre Przywara [Tue, 11 Apr 2023 22:56:14 +0000 (23:56 +0100)]
sunxi: defconfig: Add Lctech Pi F1C200s board
The Lctech Pi F1C200s (also previously known under the Cherry Pi brand)
is a small development board with the Allwinner F1C200s SoC. This is the
same as the F1C100s, but with 64MB instead of 32MB co-packaged DRAM.
Add a defconfig for this board, enabling the most basic features. This
uses the new 64MB memory map, which avoids the very tight memory map we
use for the 32MB F1C100s board(s).
The devicetree file is already in the tree, courtesy of the previous
Linux repo sync.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Andre Przywara [Sun, 2 Apr 2023 00:17:07 +0000 (01:17 +0100)]
sunxi: dts: arm/arm64: update devicetree files from Linux-v6.4-rc2
Sync the devicetree files from the official Linux kernel tree, v6.4-rc2.
This is covering both 64-bit and 32-bit Allwinner SoCs with Arm Ltd.
cores, we skip the new RISC-V bits for now, as sunxi RISC-V support
is still work in progress.
Among smaller cosmetic changes, this adds a SATA regulator node which we
need in U-Boot to get rid of hard-coded GPIOs.
Also this updates the Allwinner F1C100s DTs, enabling USB support, and
also adds the DTs for two new boards.
As before, this omits the non-backwards compatible changes to the R_INTC
controller, to remain compatible with older kernels.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
phy: rockchip-inno-usb2: Implement clock operations for usb2phy clock
This clock doesn't seem needed but appears in a phandle list used by
ehci-generic.c to bulk enable it. The phandle list comes from linux,
where it is needed for suspend/resume to work [1].
My tests give the same results with or without this patch, but Marek
Vasut found it weird to declare an empty clk_ops [2].
So I adapted the code from linux 6.1-rc8 so that it hopefully works
if it ever has some user. For now, without real use, it seems to
at least not give any errors when called.
Cc: Simon Glass <sjg@chromium.org> Cc: Philipp Tomsich <philipp.tomsich@vrull.eu> Cc: Kever Yang <kever.yang@rock-chips.com> Cc: Lukasz Majewski <lukma@denx.de> Cc: Sean Anderson <seanga2@gmail.com> Cc: Marek Vasut <marex@denx.de> Cc: Christoph Fritz <chf.fritz@googlemail.com> Cc: Jagan Teki <jagan@amarulasolutions.com> Signed-off-by: Xavier Drudis Ferran <xdrudis@tinet.cat> Reviewed-by: Kever Yang <kever.yang@rock-chips.com> Reviewed-by: Jagan Teki <jagan@amarulasolutions.com> Tested-by: Jagan Teki <jagan@amarulasolutions.com> # rk3399, rk3328, rv1126
Since clk_get_bulk() only looks for devices with UCLASS_CLK,
it fails with -ENODEV and then ehci_usb_probe() aborts.
The consequence is peripherals connected to a USB 2 port (e.g. in a
Rock Pi 4 the white port, nearer the edge) not being detected.
They're detected if CONFIG_USB_OHCI_GENERIC is selected in Kconfig,
because ohci_usb_probe() does not abort when one clk_get_by_index()
fails, but then they work in USB 1 mode.
rk3399.dtsi comes from linux and the u2phy0 was added[1] to the clock
list in:
arm64: dts: rockchip: add u2phy clock for ehci and ohci of rk3399
We found that the suspend process was blocked when it run into
ehci/ohci module due to clk-480m of usb2-phy was disabled.
[...]
Suspend concerns don't apply to U-Boot, and the problem with U-Boot
failing to probe EHCI doesn't apply to linux, because in linux
rockchip_usb2phy_clk480m_register makes u2phy0 a proper clock provider
when called by rockchip_usb2phy_probe().
So I can think of a few alternative solutions:
1- Change ehci_usb_probe() to make it more similar to
ohci_usb_probe(), and survive failure to get one clock. Looks a
little harder, and I don't know whether it could break something if
it ignored a clock that was important for something else than
suspend.
2- Change rk3399.dtsi effectively reverting the linux commit b5d1c57299734f5b54035ef2e61706b83041f20c. This dealigns the .dtsi
from linux and seems fragile at the next synchronisation.
3- Change the clock list in rk3399-u-boot.dtsi or somewhere else.
This survives .dts* sync but may survive "too much" and miss some
change from linux that we might want.
4- Enable CONFIG_USB_OHCI_GENERIC and use the ports in USB 1 mode.
This would need to be made for all boards using rk3399. In a
simple test reading one file from USB storage it gave 769.5 KiB/s
instead of 20.5 MiB/s with solution 2.
5- Trying to replicate linux and have usb2phy somehow provide a clk,
or have a separate clock device for usb2phy in addition to the phy
device.
This patch tries to implement option 5 as Marek Vasut requested in
December 5th. Options 1 and 3 didn't get through [2][3].
It just registers usb2phy as a clock driver (device_bind_driver()
didn't work but device_bind_driver_to_node() did), without any
specific operations, so that ehci-generic.c finds it and is happy. It
worked in my tests on a Rock Pi 4 B+ (rk3399).
Cc: Simon Glass <sjg@chromium.org> Cc: Philipp Tomsich <philipp.tomsich@vrull.eu> Cc: Kever Yang <kever.yang@rock-chips.com> Cc: Lukasz Majewski <lukma@denx.de> Cc: Sean Anderson <seanga2@gmail.com> Cc: Marek Vasut <marex@denx.de> Cc: Christoph Fritz <chf.fritz@googlemail.com> Cc: Jagan Teki <jagan@amarulasolutions.com> Signed-off-by: Xavier Drudis Ferran <xdrudis@tinet.cat> Reviewed-by: Kever Yang <kever.yang@rock-chips.com> Reviewed-by: Jagan Teki <jagan@amarulasolutions.com> Tested-by: Jagan Teki <jagan@amarulasolutions.com> # rk3399, rk3328, rv1126
According to the dm_serial_ops documentation, pending() should:
> @return number of waiting characters, 0 for none, -ve on error
And:
> It is acceptable to return 1 if an indeterminant number
> of characters is waiting.
With the current implementation, we have:
* FIFO is full -> pending() returns 0
* FIFO is partially used -> pending() returns 1
* FIFO is empty -> pending() returns 1
This is not the same as what the documentation requires.
Moreover, since [1], arm reset now flushes all console devices
(including serial) before the cpu gets reset.
Because of the flawed logic:
=> reset # user calls reset
flush() is called
_serial_flush() is called
ops->pending(dev, false) # never returns false
# board hangs indefinitely without resetting.
Fix it by using AML_UART_TX_EMPTY instead of AML_UART_TX_FULL.
[1] commit c5f4cdb8eb60 ("console: Use flush() before panic and reset"),
Ben Dooks [Tue, 6 Jun 2023 08:23:28 +0000 (09:23 +0100)]
ubifs: allow loading to above 4GiB
The ubifsload command is truncating any address above 4GiB as it casts
this address to an u32, instead of using an unsigned long which most of
the other load commands do. Change this to an unsigned long to allow
loading into high memory for boards which use these areas.
Andrea Merello [Fri, 26 May 2023 14:56:16 +0000 (16:56 +0200)]
I2C: cdns: Fix broken retry mechanism on arbitration lost.
In the current implementation, in case of I2C arbitration lost, a retry is
attempted; the message counter and pointer are reset to the original values
and the I2C xfer process is restart from the beginning.
However the message counter and message pointer are respectively
decremented and incremented by one before attempting any transfer, causing
the 1st transfer not to be actually retried (in case of a single transfer,
nothing is actually retried at all).
This patch fixes this: in case of retry, the 1st transfer is also retried.
Tested on a ZynqMP Kria board, with upstream older u-boot, but the involved
file and underlying logic seem basically the same.
Signed-off-by: Andrea Merello <andrea.merello@iit.it>
Ondrej Jirman [Thu, 25 May 2023 12:18:17 +0000 (14:18 +0200)]
i2c: rockchip: De-initialize the bus after start bit failure
Failure can happen when i2c is used without initializing pinctrl properly,
which U-Boot happily allows in SPL. Without this fix, further I2C access would
fail, even after proper pinctrl initialization.
Signed-off-by: Ondrej Jirman <megi@xff.cz> Cc: Heiko Schocher <hs@denx.de> Reviewed-by: Kever Yang <kever.yang@rock-chips.com> Reviewed-by: Heiko Schocher <hs@denx.de>
Mark Kettenis [Tue, 2 May 2023 19:30:41 +0000 (21:30 +0200)]
pci: apple: Add support for M2 Pro/Max
The PCIe controller on the M2 Pro/Max is different from the one
found on earlier Apple SoCs. Some registers moved and te meaning
of the bits in some other registers changed. But they are still
similar enough to handle both controllers in the same driver.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Mark Kettenis [Tue, 2 May 2023 19:30:40 +0000 (21:30 +0200)]
arm: apple: Add initial Apple M2 Pro/Max support
Apple's M2 Pro/Max SoC are somewhat similar to the M1 Pro/Max but
need a tweaked memory map. USB, NVMe, UART and WDT are working
with the existing drivers.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Manorit Chawdhry [Thu, 18 May 2023 07:14:17 +0000 (12:44 +0530)]
arm: mach-k3: security: separate out validating binary logic
K3 GP devices allows booting the secure binaries on them by bypassing
the x509 header on them.
ATF and OPTEE firewalling required the rproc_load to be called before
authentication. This change caused the failure for GP devices that
strips off the headers. The boot vector had been set before the headers
were stripped off causing the runtime stripping to fail and stripping
becoming in-effective.
Separate out the secure binary check on GP/HS devices so that the
boot_vector could be stripped before calling rproc_load. This allows
keeping the authentication later when the cluster is on along with
allowing the stripping of the binaries in case of gp devices.
Dave Gerlach [Tue, 16 May 2023 04:54:37 +0000 (10:24 +0530)]
arm: mach-k3: Increase SYSFW max image size
When booting with HS silicon, the system firmware image is 278270, which
is slightly larger than currently allocated amount.
This can cause unexpected behavior if this overlap interferes with other
things in memory, so increase this with a slightly margin added as well
to avoid any boot issues that can appear after system firmware gets
loaded.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com> Signed-off-by: Tero Kristo <kristo@kernel.org> Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com> Reviewed-by: Dhruva Gole <d-gole@ti.com>
Manorit Chawdhry [Tue, 16 May 2023 04:54:36 +0000 (10:24 +0530)]
Kconfig: j721e: Change K3_MCU_SCRATCHPAD_BASE to non firewalled region
In non-combined boot flow for K3, all the firewalls are locked by default
until sysfw comes up. Rom configures some of the firewall for its usage
along with the SRAM for R5 but the PSRAM region is still locked.
The K3 MCU Scratchpad for j721e was set to a PSRAM region triggering the
firewall exception before sysfw came up. The exception started happening
after adding multi dtb support that accesses the scratchpad for reading
EEPROM contents.
The commit changes R5 MCU scratchpad for j721e to an SRAM region.
Manorit Chawdhry [Tue, 16 May 2023 04:54:35 +0000 (10:24 +0530)]
configs: j721e: Merge the HS and non-HS defconfigs
K3 devices have runtime type board detection. Make the default defconfig
include the secure configuration. Then remove the HS specific config.
Non-HS devices will continue to boot due to runtime device type detection.
If TI_SECURE_DEV_PKG is not set the build will emit warnings, for non-HS
devices these can be ignored.
Reviewed-by: Bryan Brattlof <bb@ti.com> Reviewed-by: Neha Malcom Francis <n-francis@ti.com> Acked-by: Andrew Davis <afd@ti.com> Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
Andrew Davis [Tue, 16 May 2023 04:54:34 +0000 (10:24 +0530)]
arm: k3: config.mk: Add missing dependencies on tispl.bin HS
When building for secure devices using non-buildman based image generation
the signed tispl.bin file is called tispl.bin_HS. Also build the unsigned
tispl.bin file as expected.
Signed-off-by: Andrew Davis <afd@ti.com> Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
Peng Fan [Fri, 28 Apr 2023 04:08:46 +0000 (12:08 +0800)]
imx9: imx93_evk: update ddr timing file
Update DDR timing file generated by DDR Config Tool
1. Dynamic refresh rate is set by default
2. The 3rd freq will be 625MTS based on power and performance better than 100MTS.
Signed-off-by: Ye Li <ye.li@nxp.com> Signed-off-by: Peng Fan <peng.fan@nxp.com>
Ye Li [Fri, 28 Apr 2023 04:08:45 +0000 (12:08 +0800)]
imx9: Calculate DDR size from DDRC setting
To avoid using static setting for ECC enabled DDR size, switch
to calculate DDR size from DDRC setting
Signed-off-by: Ye Li <ye.li@nxp.com> Reviewed-by: Peng Fan <peng.fan@nxp.com> Reviewed-by: Jacky Bai <ping.bai@nxp.com> Signed-off-by: Peng Fan <peng.fan@nxp.com>
Jacky Bai [Fri, 28 Apr 2023 04:08:43 +0000 (12:08 +0800)]
ddr: imx93: update the ddr init to support mult setpoints
Update the DDR init flow for multi-setpoint support on i.MX93. A new
fsp_cfg struct need to be added in the timing file to store the diff
part of the DDRC and DRAM MR register for each setpoint.
Signed-off-by: Jacky Bai <ping.bai@nxp.com> Reviewed-by: Ye Li <ye.li@nxp.com> Signed-off-by: Peng Fan <peng.fan@nxp.com>
Jacky Bai [Fri, 28 Apr 2023 04:08:41 +0000 (12:08 +0800)]
ddr: imx9: Change the saved ddr data base to 0x2051c000
change the ddr saved info to the last 16KB of the OCRAM.
Signed-off-by: Jacky Bai <ping.bai@nxp.com> Reviewed-by: Peng Fan <peng.fan@nxp.com> Reviewed-by: Ye Li <ye.li@nxp.com> Signed-off-by: Peng Fan <peng.fan@nxp.com>
Ye Li [Fri, 28 Apr 2023 04:08:39 +0000 (12:08 +0800)]
ddr: imx9: Add workaround for DDRPHY rank-to-rank errata
According to DDRPHY errata, the Rank-to-Rank Spacing and tphy_rdcsgap
specification does not include the Critical Delay Difference (CDD) to
properly define the required rank-to-rank read command spacing after
executing PHY training firmware.
Following the errata workaround, at the end of data training, we get
all CDD values through the MessageBlock, then re-configure the DDRC
timing of WWT/WRT/RRT/RWT with comparing MAX CDD values.
Signed-off-by: Ye Li <ye.li@nxp.com> Acked-by: Peng Fan <peng.fan@nxp.com>
projects / u-boot.git / log