Masahiro Yamada [Wed, 29 Jun 2016 10:38:59 +0000 (19:38 +0900)]
pinctrl: uniphier: support pin configuration for dedicated pins
PH1-LD4 and PH1-sLD8 SoCs have pins that support pin configuration
(pin biasing, drive strength control), but not pin-muxing.
Allow to fill the mux value table with -1 for those pins; pins with
mux value -1 will be skipped in the pin-mux set function. The mux
value type should be changed from "unsigned" to "int" in order to
accommodate -1 as a special case.
Masahiro Yamada [Wed, 29 Jun 2016 10:38:58 +0000 (19:38 +0900)]
pinctrl: uniphier: split pinctrl driver for PH1-LD11 and PH1-LD20
PH1-LD11 and PH1-LD20 have much pin controlling in common, so I
added a single driver shared between them in the initial commit.
However, the Ethernet pin-mux settings I am going to add are
different with each other, and they may diverge more as the
progress of development. Split it into two dedicated drivers.
Masahiro Yamada [Wed, 29 Jun 2016 10:38:57 +0000 (19:38 +0900)]
pinctrl: uniphier: allow to have pinctrl node under syscon node
Currently, the UniPhier pinctrl driver itself is a syscon, but it
turned out much more reasonable to make it a child node of a syscon
because our syscon node consists of a bunch of system configuration
registers, not only pinctrl, but also phy, and misc registers.
It is difficult to split the node. This commit allows to migrate to
the new DT structure.
Bin Meng [Wed, 22 Jun 2016 09:30:03 +0000 (02:30 -0700)]
x86: coreboot: Remove the dummy pch driver
There is a dummy pch driver in the coreboot directory. This causes
drivers of its children fail to function due to empty ops. Remove
the whole file since it is no longer needed.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Abhimanyu Saini [Tue, 14 Jun 2016 07:48:31 +0000 (13:18 +0530)]
armv8: dts: fsl: Remove cpu nodes from Layerscape DTSIs
Currently layescape SoCs are not using cpu nodes. So removing
them in favour of compatibly with similar SoCs that
have different cores like LS2080A and LS2088A.
This has been tested on LS2080AQDS, LS1043ARDB, LS1012ARDB.
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com> Signed-off-by: Abhimanyu Saini <abhimanyu.saini@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
Peng Fan [Wed, 15 Jun 2016 02:53:02 +0000 (10:53 +0800)]
mmc: fsl: introduce wp_enable
Introudce wp_enable. To check WPSPL, wp_enable needs to be set
to 1 in board code.
Take i.MX6UL for example, for some boards, they do not use WP singal,
so they does not configure USDHC1_WP_SELECT_INPUT, and its default
value is 0(GPIO1_IO02). However GPIO1_IO02 is muxed for i2c usage and
SION bit set. So USDHC controller can always get wp signal and WPSPL
shows write protect and blocks driver continuing. This is not what
we want to see, so add wp_enable, and if set to 0, just omit the
WPSPL checking and this does not effect normal working of usdhc
controller.
If wp-gpios is provided in dts, wp_enable is set to 1, otherwise 0.
Signed-off-by: Peng Fan <van.freenix@gmail.com> Cc: Pantelis Antoniou <panto@antoniou-consulting.com> Cc: York Sun <york.sun@nxp.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Fabio Estevam <fabio.estevam@nxp.com> Tested-by: Fabio Estevam <fabio.estevam@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
Ye Li [Wed, 15 Jun 2016 02:53:01 +0000 (10:53 +0800)]
fsl_esdhc: Update clock enable bits for USDHC
The USDHC moves the 4 clock bits CARD_CLK_SOFT_EN, IPG_PERCLK_SOFT_EN,
HCLK_SOFT_EN, and IPG_CLK_SOFT_EN from sysctl register to vendorspec
register. The driver uses RSTA to replace the clock gate off
operation. But this is not a good solution because:
1. when using RSTA, we should wait this bit to clear by itself. This is not
implemeneted in the code.
2. After RSTA is set, it is recommended that the Host Driver reset the
external card and reinitialize it.
So in this patch, we change to use the vendorspec registers for these bits
operation.
Signed-off-by: Ye Li <ye.li@nxp.com> Signed-off-by: Peng Fan <van.freenix@gmail.com> Cc: York Sun <york.sun@nxp.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Pantelis Antoniou <panto@antoniou-consulting.com> Cc: Fabio Estevam <fabio.estevam@nxp.com> Tested-by: Fabio Estevam <fabio.estevam@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
Peng Fan [Wed, 15 Jun 2016 02:53:00 +0000 (10:53 +0800)]
mmc: fsl: reset to normal boot mode when eMMC fast boot
When booting in eMMC fast boot, MMC host does not exit from
boot mode after bootrom loading image. So the first command
'CMD0' sent in uboot will pull down the CMD line to low and
cause errors.
This patch cleans the MMC boot register in "mmc_init" to put the
MMC host back to normal mode.
Also clear DLL_CTRL delay line settings at USDHC initialization
to eliminate the pre-settings from boot rom.
Signed-off-by: Peng Fan <van.freenix@gmail.com> Cc: Pantelis Antoniou <panto@antoniou-consulting.com> Cc: York Sun <york.sun@nxp.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Fabio Estevam <fabio.estevam@nxp.com> Tested-by: Fabio Estevam <fabio.estevam@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
SoCs supports loading U-Boot from different medias to DRAM, such as
i.MX6/7 supports loading U-Boot to DRAM from sd/emmc/nand/qspi/spi/sata
and etc. For i.MX, imximage will generate different IVT headers according
to boot medias.
Signed-off-by: Peng Fan <peng.fan@nxp.com> Cc: Simon Glass <sjg@chromium.org> Cc: Heiko Schocher <hs@denx.de> Cc: Joe Hershberger <joe.hershberger@ni.com> Cc: Bin Meng <bmeng.cn@gmail.com> Cc: Christophe Ricard <christophe-h.ricard@st.com> Cc: Nikita Kiryanov <nikita@compulab.co.il> Cc: Francois Retief <fgretief@spaceteq.co.za> Cc: Tom Rini <trini@konsulko.com>
Steve Rae [Tue, 7 Jun 2016 18:19:38 +0000 (11:19 -0700)]
fastboot: sparse: implement reserve()
In order to process the CHUNK_TYPE_DONT_CARE properly, there is
a requirement to be able to 'reserve' a specified number of blocks
in the storage media. Because of the special handling of "bad blocks"
in NAND devices, this is implemented in a storage abstraction function.
Signed-off-by: Steve Rae <srae@broadcom.com> Reviewed-by: Maxime Ripard <maxime.ripard@free-electrons.com>
While retaining the storage abstraction feature, this is the second
set of the changes required to resync with the
cmd_flash_mmc_sparse_img()
in the file
aboot.c
from
https://us.codeaurora.org/cgit/quic/la/kernel/lk/plain/app/aboot/aboot.c?h=LE.BR.1.2.1
While retaining the storage abstraction feature, this is the first
set of the changes required to resync with the
cmd_flash_mmc_sparse_img()
in the file
aboot.c
from
https://us.codeaurora.org/cgit/quic/la/kernel/lk/plain/app/aboot/aboot.c?h=LE.BR.1.2.1
Jaehoon Chung [Fri, 13 May 2016 14:37:44 +0000 (23:37 +0900)]
mmc: dw_mmc: fix the wrong AND operation
These condition checking are wrong.
Original Author's intention might be "&" instead of "&&".
It can know whether receive or transmit data request with
BIT[4]/BIT[5] of RINTSTS register.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Heiko Schocher [Wed, 25 May 2016 05:23:48 +0000 (07:23 +0200)]
arm: at91: taurus/axm: add DM and DTS support
add DM and DTS support for the at91 based siemens
boards.
Signed-off-by: Heiko Schocher <hs@denx.de> Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
[rebased on current ToT] Signed-off-by: Andreas Bießmann <andreas@biessmann.org>
Heiko Schocher [Wed, 25 May 2016 05:23:47 +0000 (07:23 +0200)]
arm: at91: smartweb: add DM and DTS support
Signed-off-by: Heiko Schocher <hs@denx.de> Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
[rebased on current ToT] Signed-off-by: Andreas Bießmann <andreas@biessmann.org>
Marek Vasut [Sat, 14 May 2016 21:42:28 +0000 (23:42 +0200)]
ARM: at91: Don't invoke spl_boot_device() twice
Since the spl_boot_mode() is now passed the boot device to boot from,
make use of it instead of inquiring for the boot device again. This
allows board_boot_order() to function correctly.
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Andreas Bießmann <andreas.devel@googlemail.com> Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
Marek Vasut [Sat, 14 May 2016 21:42:07 +0000 (23:42 +0200)]
common: Pass the boot device into spl_boot_mode()
The SPL code already knows which boot device it calls the spl_boot_mode()
on, so pass that information into the function. This allows the code of
spl_boot_mode() avoid invoking spl_boot_device() again, but it also lets
board_boot_order() correctly alter the behavior of the boot process.
The later one is important, since in certain cases, it is desired that
spl_boot_device() return value be overriden using board_boot_order().
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Andreas Bießmann <andreas.devel@googlemail.com> Cc: Albert Aribaud <albert.u.boot@aribaud.net> Cc: Tom Rini <trini@konsulko.com> Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
[add newly introduced zynq variant] Signed-aff-by: Andreas Bießmann <andreas@biessmann.org>
Masahiro Yamada [Thu, 23 Jun 2016 04:53:46 +0000 (13:53 +0900)]
kbuild: avoid race between dtbs and dt/dt.dtb targets
If the final targets depend on both "dtbs" and "dts/dt.dtb",
and -j option is given to the command line, multiple threads
descend into the dts/ directory, which causes build error.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Tested-by: Andreas Dannenberg <dannenberg@ti.com>
Alexander Graf [Wed, 22 Jun 2016 23:15:38 +0000 (01:15 +0200)]
efi_loader: Fix typo in distro script
The distro script is supposed to use the internal fdt as fallback if we
find no viable other option. However, we're missing a space key to actually
make that work.
Add the space, so we can successfully load an EFI blob even when there is
no device tree provided on the target device.
Stephen Warren [Tue, 21 Jun 2016 19:32:07 +0000 (13:32 -0600)]
clk: sandbox: don't check clk ID against 0
clk->id is unsigned, so it can't be < 0. Remove the check for that.
FWIW, this issue was introduced when the clock API converted e.g.
clk_get_rate()'s clock ID parameter from an int to an unsigned long
(with a struct clk), without removing this check.
Fixes: 135aa9500264 ("clk: convert API to match reset/mailbox style") Reported-by: Coverity Scan Signed-off-by: Stephen Warren <swarren@nvidia.com> Acked-by: Simon Glass <sjg@chromium.org>
Andre Renaud [Mon, 20 Jun 2016 01:25:25 +0000 (19:25 -0600)]
mtd: nand: Drop a blank line in nand_wait()
This empty line should not be there. Remove it. Signed-off-by: Andre Renaud <andre@designa-electronics.com> Reviewed-by: Andreas Bießmann <andreas@biessmann.org> Signed-off-by: Simon Glass <sjg@chromium.org>
common: image: minimal android image iminfo support
We already support iminfo for other images. The idea
of this patch is start to have a minimal support for
android image format. We still need to print id[] array
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Teddy Reed [Fri, 10 Jun 2016 02:38:02 +0000 (19:38 -0700)]
mkimage: fit: spl: Add an optional static offset for external data
When building a FIT with external data (-E), U-Boot proper may require
absolute positioning for executing the external firmware. To acheive this
use the (-p) switch, which will replace the amended 'data-offset' with
'data-position' indicating the absolute position of external data.
It is considered an error if the requested absolute position overlaps with the
initial data required for the compact FIT.
Sergey Kubushyn [Tue, 7 Jun 2016 18:14:31 +0000 (11:14 -0700)]
cmd: bootefi: cosmetic
Short help (description) in bootefi command has a trailing "\n" that
breaks the "help" command output (empty line after "bootefi").
Nothing important, doesn't affect anything but better be fixed in the
upcoming release.
Still working on i.MX6 and their siblings NAND U-Boot update -- it
works here but not ready for a submission yet. Anyway it is for the
next cycle, not going to go into this release because it is too big
and may affect something else.
Also have some thoughts about fastboot (using multiple devices) but
this will go into separate email with RFC.
Masahiro Yamada [Wed, 15 Jun 2016 05:33:54 +0000 (14:33 +0900)]
tools: moveconfig: show suspicious boards with possible misconversion
There are some cases where config options are moved, but they are
ripped off at the final savedefconfig stage:
- The moved option is not user-configurable, for example, due to
a missing prompt in the Kconfig entry
- The config was not defined in the original config header despite
the Kconfig specifies it as non-bool type
- The config define in the header contains reference to another
macro, for example:
#define CONFIG_CONS_INDEX (CONFIG_SYS_LPC32XX_UART - 2)
The current moveconfig does not support recursive macro expansion.
In these cases, the conversion is very likely to be an unexpected
result. That is why I decided to display the log in yellow color
in commit 5da4f857beac ("tools: moveconfig: report when CONFIGs are
removed by savedefconfig").
It would be nice to display the list of suspicious boards when the
tool finishes processing. It is highly recommended to check the
defconfigs once again when this message is displayed.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
Masahiro Yamada [Wed, 15 Jun 2016 05:33:53 +0000 (14:33 +0900)]
tools: moveconfig: simplify show_failed_boards() and show more info
Since commit 1d085568b3de ("tools: moveconfig: display log atomically
in more readable format"), the function color_text() is clever enough
to exclude LF from escape sequences. Exploit it for removing the
"for" loops from Slots.show_failed_boards().
Also, display "(the list has been saved in moveconfig.failed)" if
there are failed boards.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
Masahiro Yamada [Wed, 15 Jun 2016 05:33:52 +0000 (14:33 +0900)]
tools: moveconfig: simplify source tree switching
The subprocess.Popen() does not change the child process's working
directory if cwd=None is given. Let's exploit this fact to refactor
the source directory handling.
We no longer have to pass "-C <reference_src_dir>" to the sub-process
because self.current_src_dir tracks the source tree against which we
want to run defconfig/autoconf.
The flag self.use_git_ref is not necessary either because we can know
the current state by checking whether the self.current_src_dir is a
valid string or None.
Masahiro Yamada [Wed, 15 Jun 2016 05:33:51 +0000 (14:33 +0900)]
tools: moveconfig: change class WorkDir to class ReferenceSource
The class WorkDir can be used in a very generic way, but currently
it is only used for containing a reference source directory.
This commit changes it for a more dedicated use. The move_config
function can be more readable by enclosing the git-clone and git-
checkout in the class constructor.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
Masahiro Yamada [Wed, 15 Jun 2016 05:33:50 +0000 (14:33 +0900)]
tools: moveconfig: fix needless move for config with default 1
When moving an integer type option with default value 1, the tool
moves configs with the same value as the default (, and then removed
by the later savedefconfig). This is a needless operation.
The KconfigParser.parse_one_config() should compare the config after
the "=y -> =1" fixup.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
Nathan Rossi [Fri, 3 Jun 2016 13:16:17 +0000 (23:16 +1000)]
net: phy: marvell: Do not reset 88e1310 after autoneg
Commit a058052c "net: phy: do not read configuration register on reset",
changes the behaviour of the phy_reset function such that the state of
the BMCR register is not preserved during reset.
Change the config function for the m88e1310 so that it does not do a
reset after configuring auto-negotiation.
Signed-off-by: Nathan Rossi <nathan@nathanrossi.com> Cc: Joe Hershberger <joe.hershberger@ni.com> Cc: Michal Simek <michal.simek@xilinx.com> Cc: Stefan Roese <sr@denx.de> Acked-by: Michal Simek <michal.simek@xilinx.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> Reviewed-by: Stefan Roese <sr@denx.de>
Alexey Firago [Thu, 26 May 2016 13:28:44 +0000 (16:28 +0300)]
net: phy: micrel: add support for KSZ886x switches in MIIM mode
This patch adds a phy driver for the Micrel KSZ886x switches.
Similarly to the KSZ8895, SoC MAC is directly connected to the switch
MAC on the switch CPU port, so the link to the switch is always up.
KSZ886x switches can be used in the following configuration modes:
- Unmanaged mode with config stored in external EEPROM
- Managed mode over SPI
- Managed mode over I2C
- Managed mode over mdio/mdc (aka MIIM or SMI)
This patch supports only unmanaged and MIIM modes.
Based on Micrel KSZ886x driver from Linux kernel and
Micrel KSZ8895 driver from U-Boot.
Verified with the KSZ8863MLL.
Signed-off-by: Alexey Firago <alexey_firago@mentor.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Stephen Warren [Tue, 26 Apr 2016 21:29:00 +0000 (15:29 -0600)]
net: rtl8169: fix switching between adapters
The rtl8169 driver uses a global variable to store the register address
of the adapter being operated upon. This is updated to point at the
correct adapter when sending or receiving a packet, or shutting down the
adapter, but not when initializing the adapter. Consequently, switching
between different adapters within the same U-Boot runtime does not work
correctly since the driver programs the wrong registers during
rtl8169_eth_start() -> rtl8169_common_start() -> rtl8169_hw_start().
Note that since rtl8169_eth_stop() does set the global variable, the
second consecutive attempt to use the "new" adapter did work even before
this patch, because each time network usage is shut down, the network
core calls stop, which sets the variable so that the next start does
actually initialize the hardware, and the adapter works.
Equally, rtl8169_eth_probe() calls rtl_init() which sets the global, so
if using only a single device, or if picking the "right" device (based on
probe order) when multiple devices are present, ioaddr will already be set
correctly from the get-go, so the issue does not occur.
Signed-off-by: Stephen Warren <swarren@nvidia.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Hans de Goede [Mon, 20 Jun 2016 21:16:28 +0000 (23:16 +0200)]
Kconfig: Add a new DISTRO_DEFAULTS Kconfig option
DISTRO_DEFAULTS is intended to mirror / replace
include/config_distro_defaults.h.
The intend is for boards which include this file to select this from
their Kconfig files and when moving setting to Kconfig which are #define-ed
in config_distro_defaults.h to select this from DISTRO_DEFAULTS so that
boards which have selected DISTRO_DEFAULTS will keep the same configuration
as before without needing any defconfig file changes.
The initial list of selected things matches all settings recently removed
from config_distro_defaults.h because they have been converted to Kconfig,
with the exception of CMD_ELF and CMD_NET, which have a default of y, if
the default of these ever changes they should be selected by DISTRO_DEFAULTS
too.
For testing and example purposes this commit also converts ARCH_SUNXI
to use DISTRO_DEFAULT instead of selecting everything it needs itself.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Chen-Yu Tsai [Tue, 7 Jun 2016 02:54:34 +0000 (10:54 +0800)]
sunxi: Add PSCI implementation in C
To make the PSCI backend more maintainable and easier to port to newer
SoCs, rewrite the current PSCI implementation in C.
Some inline assembly bits are required to access coprocessor registers.
PSCI stack setup is the only part left completely in assembly. In theory
this part could be split out of psci_arch_init into a separate common
function, and psci_arch_init could be completely in C.
Signed-off-by: Chen-Yu Tsai <wens@csie.org> Acked-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Chen-Yu Tsai [Tue, 7 Jun 2016 02:54:31 +0000 (10:54 +0800)]
sunxi: Group cpu core related controls together
Instead of listing individual registers for controls to each processor
core, list them as an array of registers. This makes accessing controls
by core index easier.
Also rename "cpucfg_sun6i.h" (which was unused anyway) to the more generic
"cpucfg.h", and add packed attribute to struct sunxi_cpucfg.
Signed-off-by: Chen-Yu Tsai <wens@csie.org> Acked-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Chen-Yu Tsai [Tue, 7 Jun 2016 02:54:27 +0000 (10:54 +0800)]
ARM: allocate extra space for PSCI stack in secure section during link phase
The PSCI implementation expects at most 2 pages worth of space reserved
at the end of the secure section for its stacks. If PSCI is relocated to
secure SRAM, then everything is fine. If no secure SRAM is available,
and PSCI remains in main memory, the reserved memory space doesn't cover
the space used by the stack.
If one accesses PSCI after Linux has fully booted, the memory that should
have been reserved for the PSCI stacks may have been used by the kernel
or userspace, and would be corrupted. Observed after effects include the
system hanging or telinit core dumping when trying to reboot. It seems
the init process gets hit the most on my test bed.
This fix allocates the space used by the PSCI stacks in the secure
section by skipping pages in the linker script, but only when there is
no secure SRAM, to avoid bloating the binary.
This fix is only a stop gap. It would be better to rework the stack
allocation mechanism, maybe with proper usage of CONFIG_ macros and an
explicit symbol.
Signed-off-by: Chen-Yu Tsai <wens@csie.org> Acked-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Chen-Yu Tsai [Tue, 7 Jun 2016 02:54:24 +0000 (10:54 +0800)]
ARM: PSCI: use only r0 and r3 in psci_get_cpu_stack_top()
For psci_get_cpu_stack_top() to be usable in C code, it must adhere to
the ARM calling conventions. Since it could be called when the stack
is still unavailable, and the entry code to linux also expects r1 and
r2 to remain unchanged, stick to r0 and r3.
Signed-off-by: Chen-Yu Tsai <wens@csie.org> Acked-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Hans de Goede [Sun, 12 Jun 2016 09:57:07 +0000 (11:57 +0200)]
sunxi: Revert "sunxi: make SoC variant choice mandatory"
This reverts commit 1a5f0de08e86("sunxi: make SoC variant choice
mandatory").
With the optional marking in the Kconfig "make savedefconfig"
will drop CONFIG_MACH_SUN4I=y from all the A10 boards, making it
hard to see at a glance which family of sunxi chips the defconfig
is for.
This commit therefore restores the optional, and restores
CONFIG_MACH_SUN4I=y to all defconfig's which had it dropped
because of this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
Hans de Goede [Sun, 12 Jun 2016 17:44:42 +0000 (19:44 +0200)]
sunxi: Add defconfig and dts file for inet86dz board
The inet86dz board is a board used in 7" tablets from various oems.
These tablets are a23 based 7" tablets featuring a 1024x600 LCD,
512MB RAM, 4G NAND, rtl8188etv usb wifi, gsl1680 touchschreen,
micro-sd slot, 3.5mm headphone jack and a micro-usb otg connector
which doubles as charging port.
The dts file this commit adds is identical to the one submitted to
the upstream kernel.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
Hans de Goede [Sat, 11 Jun 2016 13:19:38 +0000 (15:19 +0200)]
sunxi: Add defconfig and dts file for Polaroid MID2407PXE03 tablet
The Polaroid MID2407PXE03 is an a23 based 7" tablet based on a M86_MB V2.0
PCB, featuring a 800x480 LCD, 512MB RAM, 4G NAND, esp8089 wifi, gsl1680
touchschreen, micro-sd slot, 3.5mm headphone jack and a micro-usb otg
connector which doubles as charging port.
The dts file is identical to the one submitted to the upstream kernel.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
Masahiro Yamada [Mon, 20 Jun 2016 08:33:39 +0000 (17:33 +0900)]
autoboot: add CONFIG_AUTOBOOT to allow to not compile autoboot.c
Since commit bb597c0eeb7e ("common: bootdelay: move CONFIG_BOOTDELAY
into a Kconfig option"), CONFIG_BOOTDELAY is defined for all boards.
Prior to that commit, it was allowed to unset CONFIG_BOOTDELAY to
not compile common/autoboot.c, as described in common/Makefile:
# This option is not just y/n - it can have a numeric value
ifdef CONFIG_BOOTDELAY
obj-y += autoboot.o
endif
It was a bit odd to enable/disable code with an integer type option,
but it was how this option worked before that commit, and several
boards actually unset it to opt out of the autoboot feature.
This commit adds a new bool option, CONFIG_AUTOBOOT, and makes
CONFIG_BOOTDELAY depend on it.
I chose "default y" for this option because most boards use the
autoboot. I added "# CONFIG_AUTOBOOT is not set" for the boards that
had not set CONFIG_BOOTDELAY prior to the bad commit.
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com> Reviewed-by: Benoît Thébaudeau <benoit.thebaudeau.dev@gmail.com>
[scottwood: fix usage to show size as optional, and add misssing braces] Signed-off-by: Scott Wood <oss@buserror.net>
projects / u-boot.git / log