Marek Vasut [Mon, 10 Mar 2014 19:04:31 +0000 (20:04 +0100)]
arm: exynos: Squash bogus warnings in pinmux
Squash these warnings in pinmux.c found with GCC 4.8:
/arch/arm/cpu/armv7/exynos/pinmux.c: In function 'exynos_pinmux_config':
/arch/arm/cpu/armv7/exynos/pinmux.c:687:28: warning: 'count' may be used uninitialized in this function [-Wmaybe-uninitialized]
for (i = start; i < start + count; i++) {
^
/arch/arm/cpu/armv7/exynos/pinmux.c:663:16: note: 'count' was declared here
int i, start, count;
^
/arch/arm/cpu/armv7/exynos/pinmux.c:687:28: warning: 'start' may be used uninitialized in this function [-Wmaybe-uninitialized]
for (i = start; i < start + count; i++) {
^
/arch/arm/cpu/armv7/exynos/pinmux.c:663:9: note: 'start' was declared here
int i, start, count;
^
/arch/arm/cpu/armv7/exynos/pinmux.c:689:19: warning: 'bank' may be used uninitialized in this function [-Wmaybe-uninitialized]
s5p_gpio_cfg_pin(bank, i, GPIO_FUNC(0x2));
^
/arch/arm/cpu/armv7/exynos/pinmux.c:662:24: note: 'bank' was declared here
struct s5p_gpio_bank *bank;
^
/arch/arm/cpu/armv7/exynos/pinmux.c: In function 'exynos_pinmux_config':
/arch/arm/cpu/armv7/exynos/pinmux.c:687:28: warning: 'count' may be used uninitialized in this function [-Wmaybe-uninitialized]
for (i = start; i < start + count; i++) {
^
/arch/arm/cpu/armv7/exynos/pinmux.c:663:16: note: 'count' was declared here
int i, start, count;
^
/arch/arm/cpu/armv7/exynos/pinmux.c:687:28: warning: 'start' may be used uninitialized in this function [-Wmaybe-uninitialized]
for (i = start; i < start + count; i++) {
^
/arch/arm/cpu/armv7/exynos/pinmux.c:663:9: note: 'start' was declared here
int i, start, count;
^
/arch/arm/cpu/armv7/exynos/pinmux.c:689:19: warning: 'bank' may be used uninitialized in this function [-Wmaybe-uninitialized]
s5p_gpio_cfg_pin(bank, i, GPIO_FUNC(0x2));
^
/arch/arm/cpu/armv7/exynos/pinmux.c:662:24: note: 'bank' was declared here
struct s5p_gpio_bank *bank;
^
Note that the warning is bogus, the function can never be called with invalid
'peripheral' argument. GCC just cannot analyze this.
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Naveen Krishna Chatradhi <ch.naveen@samsung.com> Cc: Akshay Saraswat <akshay.s@samsung.com> Cc: Simon Glass <sjg@chromium.org> Cc: Tom Rini <trini@ti.com> Acked-by: Simon Glass <sjg@chromium.org> Acked-by: Rajeshwari S Shinde <rajeshwari.s@samsung.com> Signed-off-by: Lukasz Majewski <l.majewski@samsung.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Stefan Roese [Wed, 12 Mar 2014 09:45:41 +0000 (10:45 +0100)]
arm: am335x: DXR2: Move unconditional LAN9303 reset into command
The switch HW reset results in a disconnection of the switch port daisy-
chain for a few seconds. This is not desired in the normal field use
case. So lets remove this switch reset from the normal bootup sequence
and move it into a board specific command. This way it can be executed
in the development environment when really needed.
Signed-off-by: Stefan Roese <sr@denx.de> Cc: Roger Meier <r.meier@siemens.com> Cc: Lukas Stockmann <lukas.stockmann@siemens.com> Cc: Tom Rini <trini@ti.com>
Patch a7e36fc9 (mtd: nand: omap: remove unused #defines from common
omap_gpmc.h) removed some MTD related defines. Including
GPMC_NAND_ECC_LP_x8_LAYOUT. But this define is also needed for the
memory controller configuration (only the x8 defines are needed,
the x16 defines are the default). Without it the NAND subsystem is
not configured correctly and booting into U-Boot does not work.
Signed-off-by: Stefan Roese <sr@denx.de> Cc: Pekon Gupta <pekon@ti.com> Cc: Nikita Kiryanov <nikita@compulab.co.il> Cc: Igor Grinberg <grinberg@compulab.co.il> Cc: Tom Rini <trini@ti.com> Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Tom Rini [Mon, 10 Mar 2014 19:31:24 +0000 (15:31 -0400)]
am335x_evm: Remove SPI SPL from NOR support target
When using the am335x_evm_nor target one is generally expecting to be
used in an environment when you want to program the NOR and not a
"deployment" type target. In addition this only supports the Beaglebone
White with the memory cape and NOR module installed, which precludes the
presence of SPI flash. Drop SPI as we were getting close to the binary
limit in some cases and slightly over with other toolchains.
Vasili Galka [Sun, 9 Mar 2014 13:56:52 +0000 (15:56 +0200)]
drivers/spi/omap3: Bug fix of premature write transfer completion
The logic determining SPI "write" transfer completion was faulty. At
certain conditions (e.g. slow SPI clock freq) the transfers were
interrupted before completion. Both EOT and TXS flags of channel
status registeer shall be checked to ensure that all data was
transferred. Tested on AM3359 chip.
Tom Rini [Wed, 5 Mar 2014 19:57:47 +0000 (14:57 -0500)]
am33xx: Rework #ifdef's around s_init for clarity
The s_init function is only called on SPL or XIP cases, so lets only
build it for them. This makes the #if logic within the function a bit
clearer as to when we are or are not calling things, and makes it easier
to see that for example preloader_console_init isn't ever called in the
non-XIP full U-Boot case.
Piotr Wilczek [Fri, 7 Mar 2014 13:59:49 +0000 (14:59 +0100)]
board:trats2: Enable device tree on Trats2
This patch enables to run Trats2 board on device tree.
Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Piotr Wilczek [Fri, 7 Mar 2014 13:59:45 +0000 (14:59 +0100)]
arm:exynos: enable sdhci and misc_init to common board
This patch enables sdhci initialisation and misc_init_r in common board
file for all exynos 4 based boards.
Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Piotr Wilczek [Fri, 7 Mar 2014 13:59:43 +0000 (14:59 +0100)]
arm:exynos: add common DTS file for exynos 4
This patch adds common dtsi file and config header for all
Exynos 4 based boards.
Patch additionaly adds board specific (weak) functions for
board_early_init_f and board_power_init functions.
Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Piotr Wilczek [Fri, 7 Mar 2014 13:59:41 +0000 (14:59 +0100)]
drivers:mmc:sdhci: enable support for DT
This patch enables support for device tree for sdhci driver.
Non DT case is still supported.
Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Piotr Wilczek [Fri, 7 Mar 2014 13:59:40 +0000 (14:59 +0100)]
video:exynos_fb:fdt: add additional fdt data
This patch adds the new exynos_lcd_misc_init() function for optional
lcd specific initialisation.
Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Piotr Wilczek [Fri, 7 Mar 2014 13:59:39 +0000 (14:59 +0100)]
video:mipidsim:fdt: Add DT support for mipi dsim driver
This patch enables parsing mipi data from device tree.
Non device tree case is still supported.
Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Piotr Wilczek [Fri, 7 Mar 2014 13:59:38 +0000 (14:59 +0100)]
exynos4:pinmux:fdt: decode peripheral id
This patch adds api to decode peripheral id based on interrupt number.
Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Tim Harvey [Thu, 6 Mar 2014 15:46:30 +0000 (07:46 -0800)]
ventana: Add Gateworks Ventana family support
Gateworks Ventana is a product family based on the i.MX6. This
patch adds support for all boards in the Ventana family. Where
possible, data from the boards EEPROM is used to determine various
details about the board at runtime.
Stephen Warren [Fri, 14 Feb 2014 04:15:18 +0000 (21:15 -0700)]
usb: create common header virtual root hub descriptors
Many USB host controller drivers contain almost identical copies of the
same virtual root hub descriptors. Put these into a common file to avoid
duplication.
Note that there were some very minor differences between the descriptors
in the various files, such as:
- USB 1.0 vs. USB 1.1
- Manufacturer/Device ID
- Max packet size
- String content
I assume these aren't relevant.
Cc: Thomas Lange <thomas@corelatus.se> Cc: Shinya Kuribayashi <skuribay@pobox.com> Cc: Gary Jennejohn <garyj@denx.de> Cc: Wolfgang Denk <wd@denx.de> Cc: Eric Millbrandt <emillbrandt@coldhaus.com> Cc: Pierre Aubert <p.aubert@staubli.com> Cc: Stefan Roese <sr@denx.de> Cc: Daniel Hellstrom <daniel@gaisler.com> Cc: Denis Peter <d.peter@mpl.ch> Cc: Rodolfo Giometti <giometti@linux.it> Cc: Zhang Wei <wei.zhang@freescale.com> Cc: Mateusz Zalega <m.zalega@samsung.com> Cc: Remy Bohmer <linux@bohmer.net> Cc: Markus Klotzbuecher <mk@denx.de> Cc: Minkyu Kang <mk7.kang@samsung.com> Cc: Gary Jennejohn <garyj@denx.de> Cc: C Nauman <cnauman@diagraph.com> Cc: David Müller <d.mueller@elsoft.ch> Cc: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org> Cc: Thomas Abraham <t-abraham@ti.com> Cc: Tom Rini <trini@ti.com> Cc: Andrew Murray <amurray@embedded-bits.co.uk> Cc: Matej Frančeškin <matej.franceskin@comtrade.com> Cc: Cliff Cai <cliff.cai@analog.com> Cc: Bryan Wu <cooloney@gmail.com> Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Stephen Warren [Thu, 6 Feb 2014 20:13:06 +0000 (13:13 -0700)]
usb: ehci: fully align interrupt QHs/QTDs
These data structures are passed to cache-flushing routines, and hence
must be conform to both the USB the cache-flusing alignment requirements.
That means aligning to USB_DMA_MINALIGN. This is important on systems
where cache lines are >32 bytes.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Stephen Warren [Fri, 7 Feb 2014 16:53:50 +0000 (09:53 -0700)]
ush: ehci: initialize altnext pointers in QH
Section 4.10.2 "Advance Queue" of ehci-specification-for-usb.pdf
specifies how an EHCI controller loads a new QTD for processing if the
QH is not already marked as active. It states:
=====
If the field Bytes to Transfer is not zero and the T-bit in the Alternate
Next qTD Pointer is set to zero, then the host controller uses the
Alternate Next qTD Pointer. Otherwise, the host controller uses the Next
qTD Pointer. If Next qTD Pointer’s T-bit is set to a one, then the host
controller exits this state and uses the horizontal pointer to the next
schedule data structure.
=====
Hence, we must ensure that the alternate next QTD pointer's T-bit
(TERMINATE) is set, so the EHCI controller knows to use the next QTD
pointer.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Eric Nelson [Sat, 8 Mar 2014 14:55:52 +0000 (07:55 -0700)]
cfb_console: align fields in gzipped .bmp files
.bmp files contain 32-bit integers aligned at offsets of +2, +6,
et cetera within the bmp_header structure (see include/bmp_layout.h).
Support for gzip-compressed .bmp files is present in the cfb_console
display subsystem by uncompressing them prior to use.
This patch forces the in-memory header to be aligned properly
for these compressed images by extracting them to a 2-byte
offset in the memory returned by malloc. Since malloc will always
return a 4-byte aligned value, this forces the .bmp header
fields to be naturally aligned on 4-byte addresses.
Refer to these files for more details:
doc/README.displaying-bmps
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Ian Campbell [Fri, 7 Mar 2014 01:20:58 +0000 (01:20 +0000)]
ahci: wait longer for link.
I have observed timeouts on a cubietruck.
The increase to 40ms is completely arbitrary and Works For Me(tm). I
couldn't find a good reference for how long you are supposed to wait,
although googling around it seems like tens of ms rather than single
digits is more common. I don't think there is any harm in waiting a bit
longer.
Bo Shen [Mon, 3 Mar 2014 06:47:16 +0000 (14:47 +0800)]
mtd: nand: atmel: prepare for nand spl boot support
Prepare for nand spl boot support. It supports nand software ECC and
hardware PMECC.
This patch is take <drivers/mtd/nand/nand_spl_simple.c> as reference.
Signed-off-by: Bo Shen <voice.shen@atmel.com> Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Bo Shen [Sun, 9 Feb 2014 07:52:39 +0000 (15:52 +0800)]
ARM: atmel: add sama5d3 Xplained board support
Add sama5d3 Xplained board support which use Atmel SAMA5D36 SoC.
Now it supports boot from NAND flash and SD/MMC card.
Features support:
- NAND flash
- SD/MMC card
- Two USB hosts
- Ethernet (one GMAC, one EMAC)
Signed-off-by: Bo Shen <voice.shen@atmel.com>
[reorder boards.cfg] Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
It's called _pio_ in the version that was added to git.
Apparently it got renamed without updating the macros before it was
applied, c.f.
http://u-boot.10912.n7.nabble.com/U-Boot-PATCH-3-9-V3-add-a-new-AT91-GPIO-driver-td75922.html
Signed-off-by: Andreas Henriksson <andreas.henriksson@endian.se> Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Add support for using the Atmel MCI driver on at91sam9263ek.
This change is modeled after the existing at91sam9260ek support.
Please note that this hooks up slot1 (MCI1) for SD. Not both.
Tested with at91bootstrap and u-boot on dataflash in slot 0
and fat-formatted 8GB SDHC in slot 1 on first revision
at91sam9263ek (which must use dataflash in slot0 to boot).
CONFIG_ATMEL_MCI_PORTB not tested.
Signed-off-by: Andreas Henriksson <andreas.henriksson@endian.se>
[remove empty line] Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Priyanka Jain [Wed, 26 Feb 2014 04:08:37 +0000 (09:38 +0530)]
powerpc/t104xrdb: Update DDR initialization related settings
Update following DDR related settings for T1040RDB, T1042RDB_PI
-Correct number of chip selects to two as t1040 supports
two Chip selects.
-Update board_specific_parameters udimm structure with settings
derived via calibration.
-Update ddr_raw_timing sructure corresponding to DIMM.
-Set ODT to off. Typically on FSL board, ODT is set to 75 ohm,
but on T104xRDB, on setting this , DDR instability is observed.
Board-level debugging is in progress.
Verified the updated settings to be working fine with dual-ranked
Micron, MT18KSF51272AZ-1G6 DIMM at data rate 1600MT/s.
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com> Signed-off-by: York Sun <yorksun@freescale.com>
Priyanka Jain [Wed, 26 Feb 2014 10:41:53 +0000 (16:11 +0530)]
powerpc/t1040qds: Add Video - HDMI support
T1040 has internal display interface unit (DIU) for driving video.
T1040QDS supports video mode via
-LCD using TI enconder
-HDMI type interface via HDMI encoder
Chrontel, CH7301C encoder which is I2C programmable is used as
HDMI connector on T1040QDS.
This patch add support to
-enable Video interface for T1040QDS
-route qixis multiplexing to enable DIU-HDMI interface on board
-program DIU pixel clock gerenartor for T1040
-program HDMI encoder via I2C on board
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
Priyanka Jain [Thu, 30 Jan 2014 10:09:58 +0000 (15:39 +0530)]
powerpc/mpc85xx: Add SCFG_PIXCLKCR register support for T1040
T1040 SoC has SCFG (Supplement Configuration) Block which provides
chip specific configuration and status support. The base address of
SCFG block in T1040 is 0xfc000.
SCFG contains SCFG_PIXCLKCR (DIU pixel clock control register)
at offset 0x28.
Add definition of
-SCFG block
-SCFG_PIXCLKCR register
-Bits definition of SCFG_PIXCLK register
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
Mela Custodio [Wed, 19 Feb 2014 15:16:57 +0000 (00:16 +0900)]
bootstage: powerpc: support fdt stash and reporting
This implements stashing of bootstage timing data to FDT and automatic
timing reporting. To enable define CONFIG_BOOTSTAGE_FDT and
CONFIG_BOOTSTAGE_REPORT respectively.
Signed-off-by: Rommel G Custodio <sessyargc+u-boot@gmail.com> Reviewed-by: York Sun <yorksun@freescale.com>
USB spec says that the minimum disconnect threshold should be
over 525 mV. However, internal USB PHY threshold value is below
this specified value. Due to this some devices disconnect at
run-time. Hence, phy settings are tweaked to increased disconnect
threshold to be above 525mV by using this workaround.
Signed-off-by: Suresh Gupta <suresh.gupta@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
Shaveta Leekha [Wed, 26 Feb 2014 10:38:22 +0000 (16:08 +0530)]
powerpc/b4860: Add workaround for errata A006384 and A006475
SerDes PLLs may not lock reliably at 5 G VCO configuration(A006384)
and at cold temperatures(A006475), workaround recalibrate the
PLLs with some SerDes configuration
Both these errata are only applicable for b4 rev1.
So, make workaround for these errata conditional,
depending upon soc version.
Signed-off-by: Shaveta Leekha <shaveta@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
Shaveta Leekha [Wed, 26 Feb 2014 10:37:51 +0000 (16:07 +0530)]
B4860qds: Set SerDes2 refclk2 at to 156.25MHz for XFI to work
Change setting of SerDes2 refclk2 to have the default value as it is
coming on board that is 156.25MHz, for XFI to work.
Also change PLL_NUM variable to the one defined in config_mpc85xx.h
for B4860 and B4420.
Signed-off-by: Shaveta Leekha <shaveta@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
Shaveta Leekha [Wed, 26 Feb 2014 10:36:56 +0000 (16:06 +0530)]
board/b4860qds: Add support to make PCIe SATA work on B4860QDS
1) SerDes2 Refclks have been set properly to make
PCIe SATA to work as it work on SerDes refclk of 100MHz
2) Mask the SerDes's device reset request before changing
the Refclks for SerDes1 and SerDes2 for PLL locks to
happen properly, device reset request bit unmasked
after SerDes refclks configuration
Signed-off-by: Shaveta Leekha <shaveta@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
Shaveta Leekha [Wed, 26 Feb 2014 10:36:30 +0000 (16:06 +0530)]
board/b4860qds: Add support to make Aurora work on B4860QDS
1) Add new SerDes1 protocols having Aurora in them
2) Add VSC cross point connections for Aurora to work with
CPRI and SGMIIs
3) Configure VSC crossbar switch to connect SerDes1
lanes to aurora on board, by checking SerDes1 protocols
4) SerDes1 Refclks have been set properly to make
Aurora, CPRI and SGMIIs to work together properly
Signed-off-by: Shaveta Leekha <shaveta@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
Masahiro Yamada [Wed, 5 Mar 2014 08:40:10 +0000 (17:40 +0900)]
powerpc: mpc8260: consolidate CONFIG_MPC8260 and CONFIG_8260
Before this commit, CONFIG_MPC8260 and CONFIG_8260
were used mixed-up.
All boards with mpc8260 cpu defined both of them:
- CONFIG_MPC8260 was defined in board config headers
and include/common.h
- CONFIG_8260 was defined arch/powerpc/cpu/mpc8260/config.mk
We do not need to have both of them.
This commit keeps only CONFIG_MPC8260.
This commit does:
- Delete CONFIG_8260 and CONFIG_MPC8260 definition
in config headers and include/common.h
- Rename CONFIG_8260 to CONFIG_MPC8260
in arch/powerpc/cpu/mpc8260/config.mk.
- Rename #ifdef CONFIG_8260 to #ifdef CONFIG_MPC8260
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Cc: Wolfgang Denk <wd@denx.de>
Masahiro Yamada [Wed, 5 Mar 2014 08:25:37 +0000 (17:25 +0900)]
mips: move CONFIG_MIPS{32, 64} definition to config.mk
All mips32 boards define CONFIG_MIPS32 in config headers
except malta boards which define it in boards.cfg.
We can consolidate them by defining it in
arch/mips/cpu/mips32/config.mk.
CONFIG_MIPS64 definition can be moved to
arch/mips/cpu/mips64/config.mk as well.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com> Acked-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Masahiro Yamada [Wed, 5 Mar 2014 07:59:40 +0000 (16:59 +0900)]
kbuild: improve Kbuild speed
Kbuild brought about many advantages for us but a significant
performance regression was reported by Simon Glass.
After some discussions and analysis, it turned out
its main cause is in $(call cc-option,...).
Historically, U-Boot parses all config.mk
(arch/*/config.mk and board/*/config.mk)
every time descending into subdirectories.
That means cc-options are evaluated over and over again.
$(call cc-option,...) is useful but costly.
So we want to evaluate them only in ./Makefile
and spl/Makefile and export compiler flags.
This commit changes the build system as follows:
- Modify scripts/Makefile.build to not include config.mk
Instead, add $(PLATFORM_CPPFLAGS) to asflags-y, ccflags-y,
cppflags-y.
- Export many variables
Going forward, Kbuild will not parse config.mk files
when it descends into subdirectories.
If we want to set variables in config.mk and use them
in subdirectories, they must be exported.
This is the list of variables to get exported:
PLATFORM_CPPFLAGS
CPUDIR
BOARDDIR
OBJCOPYFLAGS
LDFLAGS
LDFLAGS_FINAL
(used in nand_spl/board/*/*/Makefile)
CONFIG_STANDALONE_LOAD_ADDR
(used in examples/standalone/Makefile)
SYM_PREFIX
(used in examples/standalone/Makefile)
RELFLAGS
(used in examples/standalone/Makefile)
- Delete CPPFLAGS
This variable has been replaced with PLATFORM_CPPFLAGS
- Copy gcclibdir from example/standalone/Makefile
to arch/sparc/config.mk
The reference in CONFIG_STANDALONE_LOAD_ADDR must be
resolved before it is exported.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Reported-by: Simon Glass <sjg@chromium.org> Acked-by: Simon Glass <sjg@chromium.org> Tested-by: Simon Glass <sjg@chromium.org> [on Sandbox] Tested-by: Stephen Warren <swarren@nvidia.com> [on Tegra]
Masahiro Yamada [Wed, 5 Mar 2014 07:59:38 +0000 (16:59 +0900)]
kbuild: add CONFIG_ prefix to USE_PRIVATE_LIBGCC
Before this commit, USE_PRIVATE_LIBGCC was defined in
arch-specific config.mk and referenced in
arch/$(ARCH)/lib/Makefile.
We are not happy about parsing config.mk again and again.
We have to keep the same behavior with a different way.
By adding "CONFIG_" prefix, this macro appears
in include/autoconf.mk, include/spl-autoconf.mk.
(And treating USE_PRIVATE_LIBGCC as CONFIG macro
is reasonable enough.)
Tegra SoC family defined USE_PRIVATE_LIBGCC as "yes"
in arch/arm/cpu/arm720t/tegra*/config.mk,
whereas did not define it in arch/arm/cpu/armv7/tegra*/config.mk.
It means Tegra enables PRIVATE_LIBGCC only for SPL.
We can describe the same behavior by adding
Many (but not all) of Blackfin boards give -O2 option
to compile under lib/ directory.
That means lib/ should be speed-optimized,
whereas other parts should be size-optimized.
We want to keep the same behavior,
but do not want to parse board/*/config.mk again and again.
We've got no choice but to invent a new method.
CONFIG_CC_OPTIMIZE_LIBS_FOR_SPEED, if it is enabled,
gives -O2 flag only for building under lib/ directory.
Dirty codes which I had marked as "FIX ME"
in board/${BOARD}/config.mk have been deleted.
Instead, CONFIG_CC_OPTIMIZE_LIBS_FOR_SPEED has been
defined in include/configs/${BOARD}.h.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Cc: Sonic Zhang <sonic.zhang@analog.com>
Tom Rini [Tue, 4 Mar 2014 20:52:35 +0000 (15:52 -0500)]
cmd_nvedit: Make 'env import -c' require size parameter
When importing a checksummed area we need to be told how big the area in
question is so that we know that will match the size of the area which
the checksum is generated against.
Reported-by: Pierre AUBERT <p.aubert@staubli.com> Signed-off-by: Tom Rini <trini@ti.com>
Stefan Roese [Tue, 4 Mar 2014 14:34:35 +0000 (15:34 +0100)]
ppc4xx: Remove 4xx NAND booting support
As ppc4xx currently only supports the deprecated nand_spl infrastructure
and nobody seems to have time / resources to port this over to the newer
SPL infrastructure, lets remove NAND booting completely.
This should not affect the "normal", non NAND-booting ppc4xx platforms
that are currently supported.
Signed-off-by: Stefan Roese <sr@denx.de> Cc: Wolfgang Denk <wd@denx.de> Cc: Tirumala Marri <tmarri@apm.com> Cc: Matthias Fuchs <matthias.fuchs@esd.eu> Cc: Masahiro Yamada <yamada.m@jp.panasonic.com> Cc: Tom Rini <trini@ti.com> Tested-by: Matthias Fuchs <matthias.fuchs@esd.eu>
Stephen Warren [Sun, 2 Mar 2014 05:18:00 +0000 (22:18 -0700)]
unit-test: make "test -e" test independent of $CWD
The unit-test for hush's "test -e" currently relies upon being run in
the U-Boot build directory, because it tests for the existence of a file
that exists in that directory.
Fix this by explicitly creating the file we use for the existence test,
and deleting it afterwards so that multiple successive unit-test
invocations succeed. This required adding an os.c function to erase
files.
Reported-by: Simon Glass <sjg@chromium.org> Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Stephen Warren [Sun, 2 Mar 2014 05:16:10 +0000 (22:16 -0700)]
hush: fix some quoted variable expansion issues
The following shell command fails:
if test -z "$x"; then echo "zero"; else echo "non-zero"; fi
(assuming $x does not exist, it prints "non-zero" rather than "zero").
... since "$x" expands to nothing, and the argument is completely
dropped, causing too few to be passed to -z, causing cmd_test() to
error out early.
This is because when variable expansions are processed by make_string(),
the expanded results are concatenated back into a new string. However,
no quoting is applied when doing so, so any empty variables simply don't
generate any parameter when the combined string is parsed again.
Fix this by explicitly replacing quoting any argument that was originally
quoted when re-generating a string from the already-parsed argument list.
This also fixes loss of whitespace in commands such as:
setenv space " "
setenv var " 1${space}${space} 2 "
echo ">>${var}<<"
Reported-by: Russell King <linux@arm.linux.org.uk> Acked-by: Simon Glass <sjg@chromium.org> Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Stephen Warren [Fri, 28 Feb 2014 05:01:28 +0000 (22:01 -0700)]
unit-test: clean up evironment after Hush tests
Delete the temporary variables that are used to save unit-test results
from the environment after running the test. This prevents polluting
the environment, or growing it too much.
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org> Acked-by: Simon Glass <sjg@chromium.org>
Stephen Warren [Thu, 27 Feb 2014 20:27:02 +0000 (13:27 -0700)]
net: asix: don't pad odd-length TX packets
For Ethernet/USB RX packets, the ASIX HW pads odd-sized packets so that
they have an even size. Currently, asix_recv() does remove this padding,
and asic_send() adds equivalent padding in the TX path. However, the HW
does not appear to need this packing for TX packets in practical testing
with "ASIX Elec. Corp. AX88x72A 000001" Vendor: 0x0b95 Product 0x7720
Version 0.1. The Linux kernel does no such padding for the TX path.
Remove the padding from the TX path:
* For consistency with the Linux kernel.
* NVIDIA has a Tegra simulator which validates that the length of USB
packets sent to an ASIX device matches the packet length value inside
the packet data. Having U-Boot and the kernel do the same thing when
creating the TX packets simplifies the simulator's validation.
Cc: Lucas Stach <dev@lynxeye.de> Cc: Marek Vasut <marex@denx.de> Cc: Simon Glass <sjg@chromium.org> Signed-off-by: Stephen Warren <swarren@nvidia.com> Acked-by: Simon Glass <sjg@chromium.org> Acked-by: Marek Vasut <marex@denx.de> Tested-by: Marek Vasut <marex@denx.de> Tested-by: Gerhard Sittig <gsi@denx.de>
OMAP3: igep00x0: Enable required clocks for GPIO that are used.
Enable required clocks for GPIO to fix a boot issue introduced by commit f33b9bd3984fb11e1d8566a866adc5957b1e1c9d (arm: omap3: Enable clocks for
peripherals only if they are used).
Without this patch the u-boot freezes after the following messages
To avoid this we just need enable the clocks for GPIOs that are used, but it
would be interesting implement a mechanism to protect these situations and
make sure that the clock is enabled when we request a GPIO.
Signed-off-by: Enric Balletbo i Serra <eballetbo@gmail.com>
B&R boards are using Phy Addresses 'one' and 'two', prior this was
defined through #define PHYADDR 1 within a header file.
Now this is addresses are given with device-driver structure.
Signed-off-by: Hannes Petermaier <oe5hpm@oevsv.at>
Stephen Warren [Wed, 5 Feb 2014 16:24:59 +0000 (09:24 -0700)]
ARM: tegra: implement bootcmd_pxe
This retrieves a PXE config file over the network, and executes it. This
allows an extlinux config file to be retrieved over the network and
executed, whereas the existing bootcmd_dhcp retrieves a U-Boot script.
Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
Stephen Warren [Wed, 5 Feb 2014 16:24:58 +0000 (09:24 -0700)]
ARM: tegra: rework boot scripts
Update the common Tegra boot scripts in the default environment to
a) Make use of the new "test -e" shell command to avoid some error
messages.
b) Allow booting using the sysboot command and extlinux.conf. This
allows easy creation of boot menus, and provides a simple interface
for distros to parameterize/configure the boot process.
Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
Stephen Warren [Wed, 5 Feb 2014 16:24:57 +0000 (09:24 -0700)]
ARM: tegra: convert tegra to use distro defaults
Modify all Tegra boards to include the "distro defaults" header, so that
all the config options distros expect are enabled. Remove any #defines
that enable the same options from the Tegra files.
Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
Stephen Warren [Mon, 10 Feb 2014 20:11:53 +0000 (13:11 -0700)]
ARM: tegra: set CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS
Tegra's EHCI controllers only have a single PORTSC register. Configure
U-Boot to know this. This prevents e.g. ehci_shutdown() from touching
non-existent registers.
Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
Stephen Warren [Mon, 3 Feb 2014 21:03:27 +0000 (14:03 -0700)]
ARM: tegra: simplify halt_avp()
In order to completely halt the AVP processor, we should simply write
FLOW_MODE_STOP without any extra options that allow wakeup. Amend the
code to do this.
I believe that enabling FIQ_1 and IRQ_1 allow the CPU to be awoken by
interrupts. We don't want this; if later SW wishes to use the AVP, it
should be reset and booted from scratch.
Related, the bits that were previously IRQ_1 and FIQ_1 have a slightly
different definition starting with Tegra114, so the values we're
writing don't entirely make sense there anyway.
Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
Register pmc_pwrgate_timer_mult has a different layout on Tegra114 and
Tegra124. Reflect this in pmc.h.
Also, simply write the whole of the register in start_cpu() rather than
doing a read-modify-write; the register is simple enough that the code
can easily construct the entire desired value.
Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
Stephen Warren [Mon, 3 Feb 2014 21:03:24 +0000 (14:03 -0700)]
ARM: tegra: move CONFIG_TEGRAnn
<asm/arch-tegra/tegra.h> needs to use CONFIG_TEGRA* to conditionalize
some definitions, since some modules moved between generations. Move
the definition of CONFIG_TEGRAnn to a header that's included earlier,
so that it's set by the time tegra.h needs to use it.
Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
pekon gupta [Fri, 22 Nov 2013 11:23:30 +0000 (16:53 +0530)]
mtd: nand: omap: move omap_elm.h from arch/arm/include/asm to drivers/mtd/nand
omap_elm.h is a generic header used by OMAP ELM driver for all TI platfoms.
Hence this file should be present in generic folder instead of architecture
specific include folder.
Build tested using: ./MAKEALL -s am33xx -s omap3 -s omap4 -s omap5
pekon gupta [Fri, 22 Nov 2013 11:23:29 +0000 (16:53 +0530)]
mtd: nand: omap: move omap_gpmc.h from arch/arm/include/asm to drivers/mtd/nand
omap_gpmc.h is a generic header used by OMAP NAND driver for all TI platfoms.
Hence this file should be present in generic folder instead of architecture
specific include folder.
Build tested using: ./MAKEALL -s am33xx -s omap3 -s omap4 -s omap5
pekon gupta [Fri, 22 Nov 2013 11:23:28 +0000 (16:53 +0530)]
mtd: nand: omap: merge duplicate GPMC data from different arch-xx headers into common omap_gpmc.h
Each SoC platform (AM33xx, OMAP3, OMAP4, OMAP5) has its own copy of GPMC related
defines and declarations scattered in SoC platform specific header files
like include/asm/arch-xx/cpu.h
However, GPMC hardware remains same across all platforms thus this patch merges
GPMC data scattered across different arch-xx specific header files into single
header file include/asm/arch/omap_gpmc.h
pekon gupta [Fri, 22 Nov 2013 11:23:27 +0000 (16:53 +0530)]
mtd: nand: omap: remove unused #defines from common omap_gpmc.h
OMAP NAND driver can detect Page-size and OOB-size of NAND device from ONFI
params or nand_id[] table. And based on that it defines ECC layout.
This patch
1) removes following board configs used for defining NAND ECC layout
- GPMC_NAND_ECC_LP_x16_LAYOUT (for large page x16 NAND)
- GPMC_NAND_ECC_LP_x8_LAYOUT (for large page x8 NAND)
- GPMC_NAND_ECC_SP_x16_LAYOUT (for small page x16 NAND)
- GPMC_NAND_ECC_SP_x8_LAYOUT (for small page x8 NAND)
2) removes unused #defines in common omap_gpmc.h depending on above configs
pekon gupta [Fri, 22 Nov 2013 11:23:26 +0000 (16:53 +0530)]
mtd: nand: omap: remove redundant platform specific header: arch-xx/omap_gpmc.h
Currently there are two sets of omap_gpmc.h header files
(a) arch/arm/include/asm/omap_gpmc.h
common header file for all platforms, containing defines and declarations used
by GPMC NAND driver.
(b) arch/arm/include/asm/arch-xx/omap_gpmc.h
SoC platform specific header file containing defines like ECC layout.
This patch removes platform specific arch-xx/omap_gpmc.c because:
- GPMC hardware engine is common for all SoC platforms hence only (a) is enough
- ECC layout is now defined in omap_nand.c driver itself based on ecc-scheme
selected. Hence all ECC layout declarations in (b) are redundant.
projects / u-boot.git / log