board/BuR: simplify default IP-setup on B&R boards.
To simplify and having a common default IP-setup on all B&R boards we
introduce an environment variable "brdefaultip" which does following.
Test if ${ipaddr} is empty, if yes it set's up some defaults:
- ipaddr : 192.168.60.1
- netmask : 255.255.255.0
- gatewayip: 192.168.60.254
- serverip : 192.168.60.254
This environment is ran from CONFIG_PREBOOT.
All other "tricks" are dropped.
Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at> Reviewed-by: Tom Rini <trini@konsulko.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Stephen Warren [Wed, 29 Jul 2015 03:55:03 +0000 (21:55 -0600)]
fat: handle paths that include ../
The FAT code contains a special case to parse the root directory. This
is needed since the root directory location/layout on disk is special
cased for FAT12/16. In particular, the location and size of the FAT12/16
root directory is hard-coded and contiguous, whereas all FAT12/16 non-root
directories, and all FAT32 directories, are stored in a non-contiguous
fashion, with the layout represented by a linked-list of clusters in the
FAT.
If a file path contains ../ (for example /extlinux/../bcm2835-rpi-cm.dtb),
it is possible to need to parse the root directory for the first element
in the path (requiring application of the special case), then a sub-
directory (in the general way), then re-parse the root directory (again
requiring the special case). However, the current code in U-Boot only
applies the special case for the very first path element, and never for
any later path element. When reparsing the root directory without
applying the special case, any file in a sector (or cluster?) other than
the first sector/cluster of the root directory will not be found.
This change modifies the non-root-dir-parsing loop of do_fat_read_at()
to detect if it's walked back to the root directory, and if so, jumps
back to the special case code that handles parsing of the root directory.
This change was tested using sandbox by executing:
(/extlinux and /backup are in different sectors so trigger some different
cases, and bcm2835-rpi-cm.dtb is in a sector of the root directory other
than the first).
In all honesty, this change is a bit of a hack, using goto and all.
However, as demonstrated above it appears to work well in practice, is
quite minimal, likely doesn't introduce any risk of regressions, and
hopefully doesn't introduce any maintenance issues.
The correct fix would be to collapse the root and non-root loops in
do_fat_read_at() and get_dentfromdir() into a single loop that has a
small special-case when moving from one sector to the next, to handle
the layout difference of root/non-root directories. AFAIK all other
aspects of directory parsing are identical. However, that's a much
larger change which needs significantly more thought before it's
implemented.
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Copyright 2005-2009 Weston Schmidt, Harald Welte and OpenMoko Inc.
Copyright 2010-2014 Tormod Volden and Stefan Schmidt
This program is Free Software and has ABSOLUTELY NO WARRANTY
Please report bugs to dfu-util@lists.gnumonks.org
A recent change introduced a link error for the composite
printer gadget driver:
`printer_unbind' referenced in section `.ref.data' of drivers/built-in.o: defined in discarded section `.exit.text' of drivers/built-in.o
Evidently the unbind function should not be marked __exit here,
because it is called through a callback pointer that is not necessarily
discarded, __composite_unbind() is indeed called from the error path of
composite_bind(), which can never work for a built-in driver.
Looking at the surrounding code, I found the same problem in all other
composite gadget drivers in both the bind and unbind functions, as
well as the udc platform driver 'remove' functions. Those will break
if anyone uses the 'unbind' sysfs attribute to detach a device from a
built-in driver.
This patch removes the incorrect annotations from all the gadget
drivers.
Bo Shen [Wed, 2 Sep 2015 10:00:06 +0000 (18:00 +0800)]
ARM: atmel: boards: use default CONFIG_SYS_PBSIZE
Entering the maximum number of characters defined by CONFIG_SYS_CBSIZE
into the console and hitting enter afterwards, causes a hang in the
system because CONFIG_SYS_PBSIZE is not capable of storing the extra
characters of the error message:
"Unknown command '' - try 'help'".
Use the default CONFIG_SYS_PBSIZE definition from config_fallbacks.h
to solve this problem.
Signed-off-by: Bo Shen <voice.shen@atmel.com> Signed-off-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Daniel Gorsulowski <daniel.gorsulowski@esd.eu> Reviewed-by: Simon Glass <sjg@chromium.org>
[fix corrupt line wraps in patch] Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Heiko Schocher [Fri, 21 Aug 2015 16:53:46 +0000 (18:53 +0200)]
arm, at91: add axm extensions
add extensions for the axm board:
- power on LED on power up
- press both recovery buttons on power up to enter
recovery mode
- detect 64 MiB and 128 MiB ramsize
- PHY rest at reboot because of ATMEL bug
- use siemens update concept
- add axm default environment
- set CONFIG_SPL_MAX_SIZE to 15k
Stefan Roese [Fri, 4 Sep 2015 12:43:00 +0000 (14:43 +0200)]
sunxi_nand_spl: Add config parameter for 4KiB page sized NAND devices
This patch adds support for NAND chips with 4KiB page size and 24/1024
ECC strength. Like the Micron MT29F32G08CBACAWP which is used on the
ICnova-A20 SoM.
Signed-off-by: Stefan Roese <sr@denx.de> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
==5581== Syscall param write(buf) points to uninitialised byte(s)
==5581== at 0x4F0F940: __write_nocancel (in /lib64/libc-2.20.so)
==5581== by 0x400839: main (in /tmp/u-boot/tools/mksunxiboot)
==5581== Address 0xffeff5d3c is on thread 1's stack
==5581== in frame #1, created by main (???)
This patch fixes the problem by clearing the whole structure instead
of just a portion of it.
Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
sunxi: Fix wrong serial console setup in Forfun Q88DB tablet
The Forfun Q88DB tablet was unbootable since commit b6006baf9c2553543e3384983d23d95efbf24fa6 ("sunxi: Move all
boards to the driver-model"). Appears that this is caused
by the wrong serial console setup in the SPL. The serial
console should use PG3/PG4 pins according to the FEX file.
Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The Wobo i5 top set box is a somewhat curious A10s based top set box,
it uses an AXP209 rather then the AXP152 usually used in combination
with the A10s. It has an ethernet phy connected to PORTD rather then
PORTA, and its built-in usb wifi is connected via the otg controller.
The dts file changes are identical to the changes submitted to the
upstream kernel.
Signed-off-by: Jelle van der Waa <jelle@vdwaa.nl> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Hans de Goede [Sat, 5 Sep 2015 15:01:31 +0000 (17:01 +0200)]
sun5i: Add q8_a13_tablet defconfig and dts
This commits adds a generic support for q8 formfactor a13 based tablets.
These tablets ship in many variants, with the difference mainly being the
touchscreen controller / accelerometer / wifi chip used.
The wifi is USB based, and thus not listed in devicetree.
ATM the kernel does not support the touchscreen / accelerometer on these
devices. In the future we may need multiple configs with different
CONFIG_DEFAULT_DEVICE_TREE settings, this depends on how we solve the
hw differences on the kernel side.
For now this will suffice.
The dts files are identical to the dts files submitted to the upstream
kernel for these tablets.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
Hans de Goede [Sat, 5 Sep 2015 08:50:56 +0000 (10:50 +0200)]
sun4i: Add defconfig and dts for the pov protab2-ips9 tablet
The Point of View protab2-ips9 is a tablet with a 9" ips 1024x768 lcd
screen, microsd slot, headphones, mini hdmi, mini usb b and power barrel
connectors.
The dts file is identical to the one submitted to the upstream kernel.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
Bin Meng [Thu, 3 Sep 2015 12:37:29 +0000 (05:37 -0700)]
net: designware: Fix build warnings
When building dm version of designware eth driver on a platform
with 64-bit phys_addr_t, it reports the following warnings:
drivers/net/designware.c: In function 'designware_eth_probe':
drivers/net/designware.c:599:2:
warning: format '%lx' expects argument of type 'long unsigned int',
but argument 3 has type 'phys_addr_t' [-Wformat]
drivers/net/designware.c:600:21:
warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
drivers/net/designware.c:601:21:
warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
This commit fixes the build warnings.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Bin Meng [Thu, 3 Sep 2015 12:37:25 +0000 (05:37 -0700)]
x86: Enable PCIe controller on quark/galileo
Quark SoC holds the PCIe controller in reset following a power on.
U-Boot needs to release the PCIe controller from reset. The PCIe
controller (D23:F0/F1) will not be visible in PCI configuration
space and any access to its PCI configuration registers will cause
system hang while it is held in reset.
Enable PCIe controller per Quark firmware writer guide.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Acked-by: Simon Glass <sjg@chromium.org>
Bin Meng [Thu, 3 Sep 2015 12:37:24 +0000 (05:37 -0700)]
x86: quark: Avoid chicken and egg problem
If we convert to use driver model pci on quark, we will encounter
some chicken and egg problems like below:
- To enable PCIe root ports, we need program some registers on the
message bus via pci bus. With driver model, the first time to
access pci bus, the pci enumeration process will be triggered.
But without first enabling PCIe root ports, pci enumeration
just hangs when scanning PCIe root ports.
- Similar situation happens when trying to access GPIO from the
PCIe enabling codes, as GPIO requires its block base address
to be assigned via a pci configuration register in the bridge.
To avoid such dilemma, replace all pci calls in the quark codes
to use the local version which does not go through driver model.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Acked-by: Simon Glass <sjg@chromium.org>
Bin Meng [Thu, 3 Sep 2015 12:37:23 +0000 (05:37 -0700)]
x86: quark: Optimize MRC execution time
Intel Quark SoC has a low end x86 processor with only 400MHz
frequency. Currently it takes about 15 seconds for U-Boot to
boot to shell and the most time consuming part is with MRC,
which is about 12 seconds. MRC programs lots of registers on
the SoC internal message bus indirectly accessed via pci bus.
To speed up the boot, create an optimized version of pci config
read/write dword routines which directly operate on PCI I/O ports.
These two routines are inlined to provide better performance too.
Now it only takes about 3 seconds to finish MRC, which is really
fast (4 times faster than before).
Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Acked-by: Simon Glass <sjg@chromium.org>
Simon Glass [Wed, 26 Aug 2015 03:52:14 +0000 (21:52 -0600)]
buildman: Improve the config comparison feature
At present buildman can compare configurations between commits but the
feature is less useful than it could be. There is no summary by architecture
and changes are not reported on a per-board basis.
Correct these deficiencies so that it is possible to see exactly what is
changing for any number of boards.
Note that 'buildman -b <branch> -C' is recommended for any build where you
will be comparing configuration. Without -C the correct configuration will
not be reported since changes will often not be picked up.
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com> Signed-off-by: Simon Glass <sjg@chromium.org>
Since that commit, patman generates useless patches for file removal;
"git format -D" prints only the header but not the diff when deleting
files, and "git am" always refuses such patches.
The following is the quotation from "man git-format-patch":
-D, --irreversible-delete
Omit the preimage for deletes, i.e. print only the header but
not the diff between the preimage and /dev/null. The resulting
patch is not meant to be applied with patch nor git apply; this
is solely for people who want to just concentrate on reviewing
the text after the change. In addition, the output obviously
lack enough information to apply such a patch in reverse, even
manually, hence the name of the option.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Acked-by: Simon Glass <sjg@chromium.org>
Bin Meng [Fri, 28 Aug 2015 05:25:56 +0000 (22:25 -0700)]
x86: crownbay: Convert to use CONFIG_DM_ETH for E1000
Since E1000 driver has been converted to driver model, enable it
on Intel Crown Bay. But the Intel Topcliff GbE driver has not been
converted to driver model yet, disable it for now.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Bin Meng [Fri, 28 Aug 2015 05:25:53 +0000 (22:25 -0700)]
dm: test: Add a new test case for dm_test_eth_rotate
Add one more ethernet device node in the sandbox test device tree,
with name 'sbe5'. This is to support a new test case for testing
network device rotation.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Bin Meng [Fri, 28 Aug 2015 05:25:51 +0000 (22:25 -0700)]
net: Revert "tftp: adjust settings to be suitable for 100Mbit ethernet"
Commit 620776d "tftp: adjust settings to be suitable for 100Mbit ethernet"
causes the following error message when trying to load a file using 'tftp'
command via a tftp server.
TFTP error: 'Unsupported option(s) requested' (8)
This is due to with commit 620776d changes, the tftp option 'timeout'
value is now set to zero which is an invalid value as per RFC2349 [1].
Valid values range between "1" and "255" seconds, inclusive. With some
tftp servers that strictly implement the RFC requirement, it reports
such an error message.
Simon Glass [Fri, 28 Aug 2015 01:54:48 +0000 (19:54 -0600)]
x86: panther: Add PCI and video configuration
Add a PCI node to the device tree. This allows SPI flash and SATA to work
correctly. Also configure the video to come up correctly even though there
is no keyboard.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Bin Meng [Thu, 27 Aug 2015 15:38:17 +0000 (08:38 -0700)]
x86: bayleybay: Change default vga bios rom address
With multiple microcode blobs included, the generated u-boot-dtb.bin
leaves merely several hundred bytes before the vga bios. Change the
vga bios rom address to make a bigger room for u-boot-dtb.bin.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Acked-by: Simon Glass <sjg@chromium.org> Tested-by: Simon Glass <sjg@chromium.org>
Bin Meng [Thu, 27 Aug 2015 15:38:15 +0000 (08:38 -0700)]
x86: ifdtool: Support checking region overlap before U-Boot
We have the capability to check regions written after U-Boot that
do not overlap. Since regions can also be written before U-Boot,
add such check for these too.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Tested-by: Andy Pont <andy.pont@sdcsystems.com> Acked-by: Simon Glass <sjg@chromium.org> Tested-by: Simon Glass <sjg@chromium.org>
Stephen Warren [Thu, 20 Aug 2015 23:38:05 +0000 (17:38 -0600)]
usb: ehci: remember init mode
When an EHCI device is registered in device mode, the HW isn't actually
initialized at all, and hence isn't left in a running state. Consequently,
when the device is deregistered, ehci_shutdown() will fail, since the HW
bits it expects to see set in response to its shutdown requests will not
be sent, and the message "EHCI failed to shut down host controller." will
be printed.
Fix ehci-hcd.c to remember whether the device was registered in host or
device mode, and only call ehci_shutdown() for host mode registrations.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Lukasz Majewski [Sun, 23 Aug 2015 22:21:44 +0000 (00:21 +0200)]
tftp: update: Allow some parts of the code to be reused when CONFIG_SYS_NO_FLASH is set
Up till now it was impossible to use code from update.c when system
was not equipped with raw FLASH memory.
Such behavior prevented DFU from reusing this code.
Signed-off-by: Lukasz Majewski <l.majewski@majess.pl> Acked-by: Joe Hershberger <joe.hershberger@ni.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Lukasz Majewski [Sun, 23 Aug 2015 22:21:42 +0000 (00:21 +0200)]
doc: dfu: tftp: README entry for TFTP extension of DFU
Documentation file for DFU extension. With this functionality it is now
possible to transfer FIT images with firmware updates via TFTP and use
DFU backend for storing them.
Signed-off-by: Lukasz Majewski <l.majewski@majess.pl> Reviewed-by: Simon Glass <sjg@chromium.org> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Commit <8bfc288c3955> ("usb: gadget: ether: Perform board
initialization from ethernet gadget driver") added board_usb_init
and board_usb_cleanup in ethernet gadget driver. But h2200 board
didn't have board_usb_init and board_usb_cleanup implementations.
This introduced the following build errors
+drivers/usb/gadget/built-in.o: In function `usb_eth_halt':
+drivers/usb/gadget/ether.c:2498: undefined reference to `board_usb_cleanup'
+drivers/usb/gadget/built-in.o: In function `usb_eth_init':
+drivers/usb/gadget/ether.c:2316: undefined reference to `board_usb_init'
Fix it here by adding empty board_usb_init and board_usb_cleanup
functions in h2200.c.
dfu: Delete superfluous initialization of the dfu_buf_size static variable
After extension of the dfu_get_buf() to also setup (implicitly) the dfu_buf_size
variable it is not needed to set dfu_buf_size to CONFIG_SYS_DFU_DATA_BUF_SIZE.
This variable is set in the dfu_get_buf() by not only considering
CONFIG_SYS_DFU_DATA_BUF but more importantly the "dfu_bufsiz" env variable.
Therefore, dfu_get_buf() should be used for initialization.
Lukasz Majewski [Sat, 15 Aug 2015 09:23:45 +0000 (11:23 +0200)]
dfu:tests: Modify dfu_gadget_test.sh to accept USB device vendor:product ID
dfu-util allows filtering on USB device vendor:product ID by using
the -d flag (-d 0451:d022).
Such option is very handy when many DFU devices are connected to a single
host PC. This commit allows testing when above situation emerges.
Signed-off-by: Lukasz Majewski <l.majewski@majess.pl> Reviewed-by: Simon Glass <sjg@chromium.org> Tested-by: Lukasz Majewski <l.majewski@majess.pl>
Test HW - AM335x Beagle Bone Black
NOTE: Max size of file to transfer: 2MiB
usb: gadget: f_thor: Allocate request up to THOR_PACKET_SIZE
Allocate request up to THOR_PACKET_SIZE not the ep0->maxpacket
as the descriptors data depend on the number of descriptors
and this 64 bytes were not enough and the buffer might overflow
which results in memalign failures later.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Dont perform reset at the end of thor download
if configured to do reset off.
Reset may not be required in all cases and hence
provided an option to do so.
The case would be to download the images to DDR instead
of flash device.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Marek Vasut [Sun, 2 Aug 2015 23:37:28 +0000 (01:37 +0200)]
arm: socfpga: Add support for DENX MCV SoM and MCVEVK board
Add support for DENX MCV SoM, which is CycloneV based and the
associated DENX MCVEVK baseboard. The board can boot from eMMC.
Ethernet and USB is supported.
Marek Vasut [Sat, 29 Aug 2015 08:16:20 +0000 (10:16 +0200)]
arm: socfpga: Do not call board_init_r() from board_init_f()
Instead of calling board_init_r() directly from board_init_f(), just
return from board_init_f(). This will make the code continue executing
in crt0.S _main(), from which the board_init_r() is called. This patch
aligns the SoCFPGA SPL with the correct SPL design as well as reduces
the stack utilisation slightly.
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Marek Vasut [Mon, 24 Aug 2015 09:51:46 +0000 (11:51 +0200)]
arm: socfpga: Assure ISWGRP 0 and 1 are inited
This fix makes sure that the ISWGRP0 and ISWGRP1 registers are
correctly inited. In case those registers are not initialized,
it is not possible to access the registers synthesised in the
FPGA through the bridges. Any such access produces data abort.
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Marek Vasut [Sat, 25 Jul 2015 08:48:14 +0000 (10:48 +0200)]
mmc: dw_mmc: Probe the MMC from OF
Rework the driver to probe the MMC controller from Device Tree
and make it mandatory. There is no longer support for probing
from the ancient qts-generated header files.
This patch now also removes previous temporary workaround.
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Dinh Nguyen <dinguyen@opensource.altera.com> Cc: Pantelis Antoniou <panto@antoniou-consulting.com> Cc: Tom Rini <trini@konsulko.com>
Sjoerd Simons [Sun, 30 Aug 2015 22:55:50 +0000 (16:55 -0600)]
rockchip: Drop first 32kb of zeros from the rkSD image type
Instead of creating a rockchip SPL SD card image with 32KB of zeros
which can be written to the start of an SD card, create the images with
only the useful data that should be written to an offset of 32KB on the
SD card.
The first 32 kilobytes aren't needed for bootup and only serve as
convenient way of accidentally obliterating your partition table.
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk> Acked-by: Simon Glass <sjg@chromium.org> Signed-off-by: Simon Glass <sjg@chromium.org>
Sjoerd Simons [Sun, 30 Aug 2015 22:55:49 +0000 (16:55 -0600)]
arm: Turn of d-cache before i-cache
Booting the kernel fails on RK3288 (and probably other rockchip SoCs)
when the i-cache is disabled/flushed before d-cache.
I have not investigated whether this is due to U-Boot hanging or whether
it's very early in the linux boot, but following the approach of the
various rockchip U-Boot forks (first disable d-cache then i-cache) makes
things work.
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk> Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Simon Glass <sjg@chromium.org>
Sjoerd Simons [Sun, 30 Aug 2015 22:55:48 +0000 (16:55 -0600)]
rockchip: Add config_distro_bootcmd support
Now that MMC works in U-Boot add config distro command support to start
Linux in a standard fashion. One oddity here is that linux fails to load
when the fdt is relocated to above 512MB, so set fdt_high to make sure it's
loaded below that.
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk> Acked-by: Simon Glass <sjg@chromium.org> Signed-off-by: Simon Glass <sjg@chromium.org>
Sjoerd Simons [Sun, 30 Aug 2015 22:55:47 +0000 (16:55 -0600)]
rockchip: Turn off CONFIG_SPL_LED for firefly
With LED support enabled the SPL easily goes over the size limit (e.g.
with both Debians gcc 4.9 and 5.2 cross-compilers). Turn off LED support
in the SPL to reduce the size just enough for those compilers.
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Tweaked commit subject to remove _SUPPORT Signed-off-by: Simon Glass <sjg@chromium.org>
Sjoerd Simons [Sun, 30 Aug 2015 22:55:44 +0000 (16:55 -0600)]
doc: Fix reference to Rock pro when Rock 2 is meant
The Radxa Rock pro board is rk3188 based and thus won't work with U-Boot
built for RK3288. Change the documentation to refer to the intended
board, the Radxa Rock 2, which is an RK3288-based design very similar to
the firefly
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk> Acked-by: Simon Glass <sjg@chromium.org> Signed-off-by: Simon Glass <sjg@chromium.org>
Simon Glass [Sun, 30 Aug 2015 22:55:41 +0000 (16:55 -0600)]
rockchip: Add basic support for firefly-rk3288
The Firefly RK3288 is a suitable target board for initial mainline Rockchip
support. It includes a good set of peripherals, a recent SoC and it is
readily available.
This adds only some basic files required to allow the baord to display a
serial message in SPL and hang.
Simon Glass [Sun, 30 Aug 2015 22:55:36 +0000 (16:55 -0600)]
rockchip: rk3288: Add SDRAM init
Add code to set up the SDRAM in SPL, ready for loading U-Boot. This uses
device tree for configuration so should be able to support other RAM
configurations. It may be possible to generalise the code to support other
SoCs at some point.
projects / u-boot.git / log