ramneek mehresh [Mon, 5 Aug 2013 10:32:53 +0000 (16:02 +0530)]
powerpc/usb: Depricate usb_phy_type and usb_dr_mode uboot env variables
Remove getting values of usb mode and phy_type from "usb_dr_mode"
and "usb_phy_type" uboot env variables. Now, these are determined
only from hwconfig string
Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com> Acked-by: York Sun <yorksun@freescale.com>
MIPS: bootm: drop obsolete Qemu specific bootm implementation
The Qemu specific bootm implementation was intended for a special
Qemu target in Linux kernel. But this target has been dropped in
v2.6.25-rc1 by commit 302922e5f6901eb6f29c58539631f71b3d9746b8
The Qemu platform was originally implemented to have an easily supportable
platform until Qemu reaches a state where it emulates a real world system.
Since the latest release Qemu is capable of emulating the MIPSsim and
Malta platforms, so this goal has been reached. The Qemu plaform is also
rather underfeatured so less useful than a Malta emulation.
Thus the special bootm implementation is obsolete by now and can be
dropped. The Qemu support in U-Boot is going to be replaced by MIPS Malta
board support.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org> Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
MIPS: bootm: add support for generic relocation of init ramdisks
All linux kernels after v2.6 require a page-aligned location of
an external init ramdisk. Enable CONFIG_SYS_BOOT_RAMDISK_HIGH to
support this with the generic U-Boot relocation code.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
edid: rename struct member to fix two EDID_* macros
Without this change EDID_DETAILED_TIMING_VSYNC_OFFSET
and EDID_DETAILED_TIMING_VSYNC_PULSE_WIDTH macros can
not be used (compile error).
The fix is quite trivial: rename struct member to the
expected name.
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Donghwa Lee [Mon, 5 Aug 2013 04:34:32 +0000 (13:34 +0900)]
exynos: video: change mipi dsi write function parameters correctly
This patch have changed mipi dsi write functions' parameters correctly
so that type cast operations were removed. And mipi dsi payload is
composed with array of panel commands to improve readability.
drivers: console: font_: Change a glyph from "broken bar" to "vertical line"
I removed these lines as they are useless in U-Boot:
#include <linux/font.h>
#define FONTDATAMAX 1536
Whole "const struct font_desc font_mini_4x6" block
This patch also adds a new configuration option to select this smaller font,
CONFIG_VIDEO_FONT_4X6 , but this is disabled by default. The default setting
is the regular "large" font.
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Anatolij Gustschin <agust@denx.de>
Marek Vasut [Tue, 30 Jul 2013 21:37:57 +0000 (23:37 +0200)]
video: Encapsulate font in video_font_data.h
This patch moves all the font configuration values into video_font_data.h
so they are all in the right place with the font. The video_font.h now only
includes video_font_data.h and will allow us to select and include different
font once more fonts are added.
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Anatolij Gustschin <agust@denx.de>
[agust: fixed build warning for mcc200] Signed-off-by: Anatolij Gustschin <agust@denx.de>
Stefan Roese [Sat, 22 Jun 2013 14:16:25 +0000 (16:16 +0200)]
mpc5200: Misc updates to a3m071 config header
This patch changes some features of the a3m071/a4m2k board support:
- Add bootcounter support
- Update MTD env default to correct values
- Add mtdparts to bootargs for mtd partitioning via kernel cmdline
- Added some default env variables for easy updating (kernel, dtb)
- Change README to the updated flash locations
Soren Brinkmann [Sat, 15 Jun 2013 00:43:24 +0000 (17:43 -0700)]
fpga: zynqpl: Clear loopback mode during device init
Some versions of the Zynq first stage boot loader enable PCAP loopback
during boot regardless of whether or not the boot image includes PL
configuration. This behavior only appears in certain boot modes (notably
QSPI boot). Attempting to configure the PL with the loopback bit set
will result in timeouts and will prevent successful configuration.
In order to avoid this problem, and to avoid dependency on the version
of the FSBL used to boot the system, ensure that the loopback enable bit
is cleared when loading the driver.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Mon, 17 Jun 2013 11:54:07 +0000 (13:54 +0200)]
fpga: zynqpl: Add support for zc7100 device.
- Add support for zc7100 device.
- FPGA programming on few of the SOC(zc7100) takes more
than 1sec, hence increased the program time by 4sec to
sync' all soc's.
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Heiko Schocher [Sat, 3 Aug 2013 05:22:53 +0000 (07:22 +0200)]
video: add an option to skip cfb console init
This patch add an option to skip cfb console init for boards
who want to show a logo, but not use the cfb console. This is
needed for the siemens boards, which have a bmp bootlogo, but
do not need the cfb console.
Signed-off-by: Heiko Schocher <hs@denx.de> Cc: Anatolij Gustschin <agust@denx.de>
[agust: use '__weak int board_cfb_skip(void)'] Signed-off-by: Anatolij Gustschin <agust@denx.de>
Heiko Schocher [Sat, 3 Aug 2013 05:22:50 +0000 (07:22 +0200)]
video, da8xx-fb: changes for am335x usage
to use this driver also on am335x based boards, the following
changes are made:
- struct lcd_ctrl_config lcd_cfg is now configurable
through board code
- controller base is configurable through define
DA8XX_LCD_CNTL_BASE. To be compatible with older
da8xx based boards: If this define is missing, the
DAVINCI_LCD_CNTL_BASE is used
- Determine LCD IP Version, and make the driver
working on lcd revision register values:
Version 1:
0x4C100102
Version 2:
0x4F200800
0x4F201000
Signed-off-by: Heiko Schocher <hs@denx.de> Cc: Stefano Babic <sbabic@denx.de> Cc: Anatolij Gustschin <agust@denx.de> Cc: Tom Rini <trini@ti.com> Acked-by: Tom Rini <trini@ti.com>
Heiko Schocher [Sat, 3 Aug 2013 05:22:48 +0000 (07:22 +0200)]
video, da8xx: move da8xx-fb.h to drivers/video
the da8xx-fb driver works also on am335x boards. So move
the da8xx-fb.h file from arch/arm/include/asm/arch-davinci
to drivers/video, so this driver can used from am335x
based boards. Also add WVGA panel_type.
Signed-off-by: Heiko Schocher <hs@denx.de> Cc: Stefano Babic <sbabic@denx.de> Cc: Anatolij Gustschin <agust@denx.de> Cc: Tom Rini <trini@ti.com> Acked-by: Tom Rini <trini@ti.com>
Marek Vasut [Tue, 30 Jul 2013 21:37:59 +0000 (23:37 +0200)]
video: Fix cfb_console for 4-bit wide font
The cfb_console can't handle 4-bit wide font properly, since with
4-bit wide font, all 8 bits are drawn. Unbreak the video_drawchars()
function to correctly render 4-bits only on such fonts.
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Anatolij Gustschin <agust@denx.de>
Marek Vasut [Tue, 30 Jul 2013 21:37:54 +0000 (23:37 +0200)]
video: Implement continuous screen refresh for SmartLCD into mxsfb
The LCDIF interface doesn't give us any means to do continuous refresh
when driving a SmartLCD. To work this around, we produce a special
circular DMA descriptor, which only writes the HW_LCDIF_CTRL0 register
and sets the RUN bit.
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Anatolij Gustschin <agust@denx.de> Cc: Fabio Estevam <fabio.estevam@freescale.com> Cc: Otavio Salvador <otavio@ossystems.com.br> Cc: Stefano Babic <sbabic@denx.de>
Marek Vasut [Tue, 30 Jul 2013 21:37:53 +0000 (23:37 +0200)]
video: Add System-Mode configuration hook into mxsfb
Add hook that allow configuring SmartLCD attached the MXS LCDIF
controller operating in System-Mode. This hook can be overriden
by a platform-specific SmartLCD programming routine, which writes
the SmartLCD specific values into it's registers.
Also, this patch makes sure the SYNC signals are off for the
SmartLCD case.
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Anatolij Gustschin <agust@denx.de> Cc: Fabio Estevam <fabio.estevam@freescale.com> Cc: Otavio Salvador <otavio@ossystems.com.br> Cc: Stefano Babic <sbabic@denx.de>
Marek Vasut [Tue, 30 Jul 2013 21:37:51 +0000 (23:37 +0200)]
dma: apbh: Add special circular mode for LCD
Add special function that executes a specially crafted circular
DMA descriptor. The function doesn't wait for the descriptor to
finish the transfer, since the descritor never finishes. This is
useful when operating a SmartLCD through the LCDIF interface, as
the LCDIF does not give us any means to have continuous refresh
of the SmartLCD. Instead, the RUN bit in the LCDIF CTRL register
must be triggered manually. This can be worked around by starting
an DMA transfer which continuously sets the RUN bit. This function
allows starting exactly such transfer.
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Anatolij Gustschin <agust@denx.de> Cc: Fabio Estevam <fabio.estevam@freescale.com> Cc: Otavio Salvador <otavio@ossystems.com.br> Cc: Stefano Babic <sbabic@denx.de>
Mingkai Hu [Thu, 4 Jul 2013 09:33:43 +0000 (17:33 +0800)]
powerpc/c29xpcie: add support for C29XPCIE board
C29XPCIE board is a series of Freescale PCIe add-in cards to perform
as public key crypto accelerator or secure key management module. It
includes C293PCIE board, C293PCIE board and C291PCIE board.
- 512KB platform SRAM in addition to 512K L2 Cache/SRAM
- 512MB soldered DDR3 32bit memory
- CPLD System Logic
- 64MB x16 NOR flash and 4GB x8 NAND flash
- 16MB SPI flash
Signed-off-by: Mingkai Hu <Mingkai.Hu@freescale.com> Singed-off-by: Po Liu <Po.Liu@freescale.com>
[yorksun: Fixup include/configs/C29XPCIE.h] Signed-off-by: York Sun <yorksun@freescale.com>
Mingkai Hu [Thu, 4 Jul 2013 09:30:36 +0000 (17:30 +0800)]
powerpc/85xx: Add C29x SoC support
The Freescale C29x family is a high performance crypto co-processor.
It combines a single e500v2 core with necessary SEC engine. There're
three SoC types(C291, C292, C293) with the following features:
T4240 PCIe IP is version 3.0 and has some update comparing previous
QorIQ products.
1. Move Freescale specific register define
to
arch/powerpc/include/asm/fsl_pci.h
and update the register offset define for T4240.
2. add the status/control register define
use status/control register to judge the link status
3. The original code uses 'Programming Interface' field to judge if PCIE is
EP or RC mode, however, T4240 does not support this functionality.
According to PCIE specification, 'Header Type' offset 0x0e is used to
indicate header type, so for PCIE controller, the patch changes code to
use 'Header Type' field to identify if the PCIE is RC or EP mode.
This patch fixes the PCIe card link up issue on T4240QDS.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com> Signed-off-by: Minghuan Lian <Minghuan.Lian@freescale.com> Signed-off-by: York Sun <yorksun@freescale.com>
Minghuan Lian [Wed, 3 Jul 2013 10:32:41 +0000 (18:32 +0800)]
powerpc/rman: fix RMan support for t4240 and b4860
1. Add CONFIG_SYS_DPAA_RMAN macro to t4240 and b4860.
2. Decrease RMan liodn offset number.
SET_RMAN_LIODN() is used to set liodn offset of RMan blocks 0-3.
For t4240 and b4860, RMan liodn base is assigned to 922, the original
offset number is too large that the liodn (base+offset 922+678 = 1600)
is greater than 0x500 the maximum liodn number.
Signed-off-by: Minghuan Lian <Minghuan.Lian@freescale.com> Signed-off-by: York Sun <yorksun@freescale.com>
board/b4860qds: Add support for configuring SerDes1 Refclks
1) Add support in B4860 board files for using IDT driver where
IDT8T49N222A is a low phase noise Frequency Translator / Synthesizer
that generate different refclks for SerDes modules, used this driver
for reconfiguring SerDes1 Refclks(based on SerDes1 protocols)
for CPRI to work. CPRI works on 122.88MHz and default refclks coming
on board are not suitable for it
2) Move SerDes1 refclk1 source selection from eth_b4860qds.c file
to b4860qds board file, as SerDes1 Refclk1 would come from
PHY MUX in case of certain protocols, that have been checked here.
This change would make on board SGMIIs to work
3) Add I2C addresses for IDT8T49N222A devices in board/include file
4) Add define for PCA-I2C bus multiplexer, on which IDT devices exist
Signed-off-by: Shaveta Leekha <shaveta@freescale.com> Acked-by: York Sun <yorksun@freescale.com>
Add code for configuring IDT8T49N222A device for various output refclks
- The IDT8T49N222A is a low phase noise Frequency Translator / Synthesizer with
alarm and monitoring functions suitable for networking and
communications applications. It is able to generate wide range of output
frequencies.
- In B4860QDS, it has been used to generate different refclks to SerDes modules
- Programming of these devices are performed by I2C interface.
Signed-off-by: Shaveta Leekha <shaveta@freescale.com> Acked-by: York Sun <yorksun@freescale.com>
BSC9132 SoC has two separate DDR controllers for PowerPC side and DSP side
DDR. They are mapped to PowerPC and DSP CCSR space respectively.
BSC9132QDS has two on-board MC34716EP DDR3 memory one connected to PowerPC
and other to DSP side controller.
Configure DSP DDR controller similar to PowerPC side DDR controller as
memories are exactly similar.
Signed-off-by: Manish Jaggi <manish.jaggi@freescale.com> Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com> Acked-by: York Sun <yorksun@freescale.com>
BSC9132QDS is a Freescale Reference Design Board for BSC9132 SoC which is a
integrated device that contains two powerpc e500v2 cores and two DSP
starcores.
To support DSP starcore
-Creating LAW and TLB for DSP-CCSR space.
-Creating LAW for DSP-core subsystem M2 and M3 memory
-Creating LAW for 1GB DDR which is connected exclusively to DSP-cores
Signed-off-by: Manish Jaggi <manish.jaggi@freescale.com> Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com> Acked-by: York Sun <yorksun@freescale.com>
Liu Gang [Fri, 28 Jun 2013 09:58:37 +0000 (17:58 +0800)]
powerpc/srio-pcie-boot: Avoid the NOR_BOOT macro when boot from SRIO/PCIE
When a board (slave) boots from SRIO/PCIE, it would get the instructions
from a remote board (master) by SRIO/PCIE interface, and the slave's
u-boot image should be built with the
SYS_TEXT_BASE=0xFFF80000;
So the u-boot of the slave should avoid the NOR_BOOT branch at the
booting stage.
For example, when a P2041RDB boots from SRIO/PCIE, it will set TLB
entry 15 from base address "CONFIG_SYS_MONITOR_BASE & 0xffc00000",
and with the 4M size as the boot window in NOR_BOOT branch. Because
the CONFIG_SYS_MONITOR_BASE = CONFIG_SYS_TEXT_BASE = 0xFFF80000, so
the TLB entry will be from base address 0xffc00000 and with 4M size.
Then the u-boot will set TLB entry 14 from base address
"CONFIG_SYS_INIT_RAM_ADDR", and with the 16K size as the initial
stack window. For the P2041RDB platform, the CONFIG_SYS_INIT_RAM_ADDR
= 0xffd00000. So the TLB entry 14 and 15 will be in confliction.
There will be right TLB entries configurations when avoid the
NOR_BOOT branch and set the boot window from 0xfff00000 with 1M
size space.
Haijun.Zhang [Fri, 28 Jun 2013 02:47:09 +0000 (10:47 +0800)]
p1020rdb-pd: platform support
Add new board p1020RDB-PD. P1020RDB-PD board was update from P1020RDB.
DDR changed from DDR2 1G to DDR3 2G.
NAND: 128 MiB
Flash: 64 MiB
Also change P1020RDB to P1020RDB-PC to distinguish from P1020RDB board.
Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com> Signed-off-by: Haijun Zhang <Haijun.Zhang@freescale.com> CC: Scott Wood <scottwood@freescale.com> Acked-by: York Sun <yorksun@freescale.com>
York Sun [Tue, 25 Jun 2013 18:37:49 +0000 (11:37 -0700)]
powerpc/mpc85xx: Workaround for A-005812
Erratum A-005812 Incorrect reservation clearing in Write Shadow mode can
result in invalid atomic operations. For u-boot, this erratum only impacts
SoCs running in write shadow mode.
York Sun [Tue, 25 Jun 2013 18:37:48 +0000 (11:37 -0700)]
powerpc/mpc8xxx: Add memory reset control
JEDEC spec requires the clocks to be stable before deasserting reset
signal for RDIMMs. Clocks start when any chip select is enabled and
clock control register is set. This patch also adds the interface to
toggle memory reset signal if needed by the boards.
York Sun [Tue, 25 Jun 2013 18:37:47 +0000 (11:37 -0700)]
powerpc/mpc8xxx: Add x4 DDR device support
On selected platforms, x4 DDR devices can be supported. Using x4 devices may
lower the performance, but generally they are available for higher density.
York Sun [Tue, 25 Jun 2013 18:37:45 +0000 (11:37 -0700)]
powerpc/mpc8xxx: Set inactive csn_bnds to 0xffffffff
When chip select interleaving is enabled, cs0_bnds is used for address
binding. Other csn_bnds are not used. When two controllers interleaving is
enabled, cs0_bnds of both controllers are used, other csn_bnds are not.
However, the unused csn_bnds may be used internally for calculating
addresses for calibration. Setting those registers to 0 may confuse
controllers in some cases. Instead, setting them to 0xffffffff together
with normal LAWs will guarantee the address is not mapped to DDR.
York Sun [Thu, 27 Jun 2013 17:48:29 +0000 (10:48 -0700)]
powerpc/T4240EMU: Add T4240EMU target
Add emulator support for T4240. Emulator has limited peripherals and
interfaces. Difference between emulator and T4240QDS includes:
ECC for DDR is disabled due the procedure to load images
No board FPGA (QIXIS)
NOR flash has 32-bit port for higher loading speed
IFC and I2C timing don't really matter, so set them fast
No ethernet
York Sun [Tue, 25 Jun 2013 18:37:41 +0000 (11:37 -0700)]
mpc85xx: Base emulator support
Prepare for emulator support for mpc85xx parts.
Disable DDR training and skip wrlvl_cntl_2 and wrlvl_cntl_3 registers.
These two registers improve stability but not supported by emulator.
Add CONFIG_FSL_TBCLK_EXTRA_DIV for possible adjustment to time base.
Liu Gang [Tue, 25 Jun 2013 10:12:12 +0000 (18:12 +0800)]
powerpc/srio: Update the SRIO LIODN registers and ID table macro
For some PowerPC platforms, LIODN registers for SRIO ports are
in SRIO register address space. So the ccsr_rio structure should
be updated for those LIODN registers.
In addition, add a new macro "SET_SRIO_LIODN_BASE" to create
the SRIO LIODN ID table based on the SRIO LIODN register address.
Signed-off-by: Liu Gang <Gang.Liu@freescale.com> Acked-by: York Sun <yorksun@freescale.com>
Xie Xiaobo [Mon, 24 Jun 2013 07:01:30 +0000 (15:01 +0800)]
powerpc/85xx: Add TWR-P10xx board support
TWR-P1025 Specification:
-----------------------
Memory subsystem:
512MB DDR3 (on board DDR)
64Mbyte 16bit NOR flash
One microSD Card slot
Ethernet:
eTSEC1: Connected to Atheros AR8035 GETH PHY
eTSEC3: Connected to Atheros AR8035 GETH PHY
UART:
Two UARTs are routed to the FDTI dual USB to RS232 convertor
USB: Two USB2.0 Type A ports
I2C:
AT24C01B 1K Board EEPROM (8 bit address)
QUICC Engine:
Connected to DP83849i PHY supply two 10/100M ethernet ports
QE UART for RS485 or RS232
PCIE:
One mini-PCIE slot
Signed-off-by: Michael Johnston <michael.johnston@freescale.com> Signed-off-by: Xie Xiaobo <X.Xie@freescale.com>
[yorksun: Fixup include/configs/p1_twr.h] Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kuan-Yu Kuo <ken.kuoky@gmail.com> Cc: Macpaul Lin <macpaul@gmail.com> Cc: Andes <uboot@andestech.com> Signed-off-by: Andes <uboot@andestech.com>
The driver assumes that the DMA allocation API are provided by all
architectures. This is not the case for nds32 and it causes a
build error. This patch adds DMA allocation API to avoid the errors.
Signed-off-by: Kuan-Yu Kuo <ken.kuoky@gmail.com> Cc: Macpaul Lin <macpaul@gmail.com> Cc: Andes <uboot@andestech.com> Signed-off-by: Andes <uboot@andestech.com>
Michal Simek [Thu, 8 Aug 2013 13:28:11 +0000 (18:58 +0530)]
microblaze: Call spi_init function
Initialization spi.
Signed-off-by: Michal Simek <monstr@monstr.eu> Acked-by: Stephan Linz <linz@li-pro.net> Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Marek Vasut [Thu, 1 Aug 2013 10:32:20 +0000 (12:32 +0200)]
i2c: soft: Fix typo in CONFIG_SYS_I2C_SOFT_SPEED
In case only the CONFIG_SYS_I2C_SPEED is set in configuration file,
the CONFIG_SYS_I2C_SOFT_SPEED is defined as CONFIG_SYS_I2C_SPEED.
The CONFIG_SYS_I2C_SOFT_SPEED is then used throughout the driver.
Unfortunatelly, due to a typo in the driver, instead of defining
CONFIG_SYS_I2C_SOFT_SPEED, an CONFIG_SYS_SOFT_I2C_SPEED was defined
and therefore the driver failed to compile. The same applies for
CONFIG_SYS_I2C_SOFT_SLAVE , where the swap happens as well.
This patch fixes the issue.
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Heiko Schocher <hs@denx.de>
Stephen Warren [Wed, 24 Jul 2013 17:09:24 +0000 (10:09 -0700)]
dts/Makefile: pass -undef -D__DTS__ to cpp
This brings U-Boot's cpp invocation into line with the way the Linux
kernel invokes cpp on device trees. Consistency will be useful to ensure
*.dts is portable between the two.
-undef also has the added advantage of not defining "linux", so DT
property names such as "linux,keymap" don't get mangled.
Signed-off-by: Stephen Warren <swarren@nvidia.com> Acked-by: Simon Glass <sjg@chromium.org>
Stephen Warren [Wed, 24 Jul 2013 17:09:23 +0000 (10:09 -0700)]
dts/Makefile: don't use cpp -P
Recent dtc supports #line directives in the input source code, and even
uses them to generate useful line numbers in any messages it emits. Stop
passing -P to cpp, since there's no need any more.
Signed-off-by: Stephen Warren <swarren@nvidia.com> Acked-by: Simon Glass <sjg@chromium.org>
Stephen Warren [Wed, 24 Jul 2013 17:09:20 +0000 (10:09 -0700)]
dt: don't use ARCH_CPU_DTS
Now that we assume dtc supports the -i option, we don't need to use
ARCH_CPU_DTS in *.dts{,i}; we simply specify the include filename
directly, and dtc will find it.
Signed-off-by: Stephen Warren <swarren@nvidia.com> Acked-by: Simon Glass <sjg@chromium.org>
Stephen Warren [Wed, 24 Jul 2013 17:09:19 +0000 (10:09 -0700)]
dts/Makefile: unify cpp/dtc include paths
*.dts may use #include (via cpp) or /include/ (via dtc; assuming a newer
dtc). The choice is up to the creator of the DT. Create a common variable
DTC_INCDIRS that lists the paths searched by include statements, and
update cpp and dtc invocation to use them.
For cpp, also specify -nostdinc to ensure the same set of paths is
available to both type of include statement.
For dtc, create a new DTC_FLAGS variable to hold all the flags passed to
dtc.
Signed-off-by: Stephen Warren <swarren@nvidia.com> Acked-by: Simon Glass <sjg@chromium.org>
Stephen Warren [Wed, 24 Jul 2013 17:09:18 +0000 (10:09 -0700)]
dts/Makefile: simplify dtc invocation
The invocation of dtc is significantly more complex that it could be,
in order to work around an issue on old versions of dtc, which print
a message to stdout every time they run.
Remove this workaround, on the assumption that people have or will
upgrade to a newer version of dtc. This simplifies the build rule
significantly.
Related, split the invocation of cpp and dtc into separate commands
rather than a pipeline, so that if either fail, it is detected. This has
the nice benefit of saving off the result of the pre-processing step,
allowing it to be easily inspected.
Assuming a new enough dtc (which an earlier patch enforces), dtc will
parse #line directives in its input file, and generate correct file and
line numbers in error messages, even though cpp is unconditionally
applied to its input file.
Signed-off-by: Stephen Warren <swarren@nvidia.com> Acked-by: Simon Glass <sjg@chromium.org>
Stephen Warren [Wed, 24 Jul 2013 17:09:17 +0000 (10:09 -0700)]
xilinx: move microblaze-generic .dts to standard location
Aside from microblaze, all other SoCs/boards/vendors store their DT files
in board/$vendor/dts/$soc-$board.dts. Move microblaze-generic.dts to this
location for consistency.
Signed-off-by: Stephen Warren <swarren@nvidia.com> Acked-by: Simon Glass <sjg@chromium.org> Acked-by: Michal Simek <monstr@monstr.eu>
Axel Lin [Fri, 12 Jul 2013 09:39:41 +0000 (17:39 +0800)]
spi: bfin_spi: Use DIV_ROUND_UP instead of open-coded
Use DIV_ROUND_UP to simplify the code.
Signed-off-by: Axel Lin <axel.lin@ingics.com> Signed-off-by: Scott Jiang <scott.jiang.linux@gmail.com> Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Axel Lin [Mon, 1 Jul 2013 05:16:17 +0000 (13:16 +0800)]
blackfin: Fix using gd->baudrate before setting its value
Current code uses gd->baudrate before setting its value.
Besides, I got below build warning which is introduced by
commit ddb5c5be "blackfin: add baudrate to bdinfo".
board.c:235:3: warning: passing argument 1 of 'simple_strtoul' makes pointer from integer without a cast [enabled by default]
include/vsprintf.h:27:7: note: expected 'const char *' but argument is of type 'unsigned int'
This patch ensures we get the baudrate setting before using it.
Signed-off-by: Axel Lin <axel.lin@ingics.com> Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Axel Lin [Fri, 28 Jun 2013 06:45:06 +0000 (14:45 +0800)]
blackfin: gpio: Use proper mask for comparing function
The function return from P_FUNCT2MUX(per) takes 2 bits, however
for BF537_FAMILY with offset != 1 the function is 1 bit.
Also has small refactor for better readability.
In portmux_setup(), it looks odd having "muxreg &= ~(3 << 1);"
while in current code we do muxreg |= (function << offset);.
projects / u-boot.git / log