Mike Frysinger [Thu, 23 Jul 2009 20:37:03 +0000 (16:37 -0400)]
atmel_df_pow2: standalone to convert dataflashes to pow2
Atmel DataFlashes by default operate with pages that are slightly bigger
than normal binary sizes (i.e. many are 1056 byte pages rather than 1024
bytes). However, they also have a "power of 2" mode where the pages show
up with the normal binary size. The latter mode is required in order to
boot with a Blackfin processor, so many people wish to convert their
DataFlashes on their development systems to this mode. This standalone
application does just that.
Mike Frysinger [Wed, 2 Sep 2009 08:21:16 +0000 (04:21 -0400)]
Blackfin: enable 64bit printf for nand
Since the NAND code now uses 64bit code, make sure we enable support for
ADI Blackfin boards in printf to avoid the warning:
nand_util.c:45:2: warning: #warning Please define CONFIG_SYS_64BIT_VSPRINTF for correct output!
Mike Frysinger [Tue, 25 Aug 2009 00:48:04 +0000 (20:48 -0400)]
Blackfin: use scratch pad for exception stack
If the memory layout pushes the stack out of the default DCPLB coverage,
the exception handler may trigger a double fault by trying to push onto
the uncovered stack. So handle the exception stack similar to the kernel
by using the top of the scratch pad SRAM.
Robin Getz [Mon, 17 Aug 2009 15:23:02 +0000 (15:23 +0000)]
Blackfin: change global data register from P5 to P3
Since the Blackfin ABI favors higher scratch registers by default, use the
last scratch register (P3) for global data rather than the first (P5).
This allows the compiler's register allocator to use higher number scratch
P registers, which in turn better matches the Blackfin instruction set,
which reduces the size of U-Boot by more than 1024 bytes...
Signed-off-by: Robin Getz <robin.getz@analog.com> Signed-off-by: Mike Frysinger <vapier@gentoo.org>
David Brownell [Sun, 30 Aug 2009 18:05:29 +0000 (11:05 -0700)]
bugfix CONFIG_SYS_CONSOLE_INFO_QUIET
The "console: unify printing current devices" patch goofed:
CONFIG_SYS_CONSOLE_INFO_QUIET is supposed to *REMOVE* boot
time noise, not add it. Said patch changed the #ifndefs
to #ifdef; this one restores them to the proper sense.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Timur Tabi [Fri, 28 Aug 2009 21:56:45 +0000 (16:56 -0500)]
fsl: simplify the "mac id" command, improve boot-time informational message
The "mac id" command took a 4-character parameter as the identifier string.
However, for any given board, only one kind of identifier is acceptable, so it
makes no sense to ask the user to type it in. Instead, if the user enters
"mac id", the identifier (and also the version, if it's NXID) will
automatically be set to the correct value.
Improve the message that is displayed when EEPROM is read during boot. It now
displays "EEPROM:" and then either an error message or the EEPROM identifier
if successful.
If the identifier in EEPROM is valid, then always reject a bad CRC, even if the
CRC field has not been initialized.
Don't force the MAC address count to MAX_NUM_PORTS or less. Forcing the value
to be changed resulting in an in-memory copy that does not match what's in
hardware, even though the user did not request that change.
Finally, always update the CRC value in the in-memory copy after any field
is changed, so that the CRC is always correct.
Signed-off-by: Timur Tabi <timur@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Poonam Aggrwal [Fri, 21 Aug 2009 01:59:42 +0000 (07:29 +0530)]
driver/fsl_pci: Add fsl_pci_init_port function to initialize a PCI controller
fsl_pci_init_port can be called from board specific PCI initialization
routines to setup the PCI (or PCIe) controller. This will reduce code
redundancy in most of the 85xx/86xx FSL board ports that setup PCI.
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Timur Tabi [Thu, 20 Aug 2009 22:41:11 +0000 (17:41 -0500)]
85xx: Improve MPIC initialization
The MPIC initialization code for Freescale e500 CPUs was not using I/O
accessors, and it was not issuing a read-back to the MPIC after setting
mixed mode. This may be the cause of a spurious interrupt on some systems.
Signed-off-by: Timur Tabi <timur@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Felix Radensky [Sat, 15 Aug 2009 12:08:37 +0000 (15:08 +0300)]
85xx: Fix memory test range on MPC8536DS
With current values of CONFIG_SYS_MEMTEST_START and CONFIG_SYS_MEMTEST_END
memory test hangs if run without arguments. Set them to sane values, so
that all available 512MB of RAM excluding exception vectors at the bottom
and u-boot code and stack at the top can be tested.
Signed-off-by: Felix Radensky <felix@embedded-sol.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Kumar Gala [Fri, 7 Aug 2009 18:00:55 +0000 (13:00 -0500)]
85xx: Move to a common linker script
There are really no differences between all the 85xx linker scripts so
we can just move to a single common one. Board code is still able to
override the common one if need be.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
P1020 is another member of QorIQ series of processors which falls in ULE
category. It is an e500 based dual core SOC.
Being a scaled down version of P2020 it has following differences:
- 533MHz - 800MHz core frequency.
- 256Kbyte L2 cache
- Ethernet controllers with classification capabilities.
Also the SOC is pin compatible with P2020
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Poonam Aggrwal [Wed, 5 Aug 2009 07:59:24 +0000 (13:29 +0530)]
85xx: Add support for P2020RDB board
The code base adds P1 & P2 RDB platforms support.
The folder and file names can cater to future SOCs of P1/P2 family.
P1 & P2 processors are 85xx platforms, part of Freescale QorIQ series.
Tested following on P2020RDB:
1. eTSECs
2. DDR, NAND, NOR, I2C.
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The number of CPUs are getting detected dynamically by checking the
processor SVR value. Also removed CONFIG_NUM_CPUS references from all
the platforms with 85xx/86xx processors.
This can help to use the same u-boot image across the platforms.
Also revamped and corrected few Freescale Copyright messages.
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Kumar Gala [Wed, 5 Aug 2009 12:59:35 +0000 (07:59 -0500)]
pci/fsl_pci_init: Rework PCI ATMU setup to handle >4G of memory
The old PCI ATMU setup code would just mimic the PCI regions into the
ATMU registers. For simple memory maps in which all memory, MMIO, etc
space fit into 4G this works ok. However there are issues with we have
>4G of memory as we know can't access all of memory and we need to
ensure that PCICSRBAR (PEXCSRBAR on PCIe) isn't overlapping with
anything since we can't turn it off.
We first setup outbound windows based on what the board code setup
in the pci regions for MMIO and IO access. Next we place PCICSRBAR
below the MMIO window. After which we try to setup the inbound windows
to map as much of memory as possible.
On PCIe based controllers we are able to overmap the ATMU setup since
RX & TX links are separate but report the proper amount of inbound
address space to the region tracking to ensure there is no overlap.
On PCI based controllers we use as many inbound windows as available to
map as much of the memory as possible.
Additionally we changed all the CCSR register access to use proper IO
accessor functions. Also had to add CONFIG_SYS_CCSRBAR_PHYS to some
86xx platforms that didn't have it defined.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Kumar Gala [Wed, 5 Aug 2009 12:49:27 +0000 (07:49 -0500)]
pci/fsl_pci_init: Use PCIe capability to determine if controller is PCIe
Change the code to use the PCIe capabilities register to determine if we
are a PCIe controller or not. Additionally cleaned up some white space
and formatting in the file.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Kumar Gala [Tue, 4 Aug 2009 02:02:02 +0000 (21:02 -0500)]
pci/fsl_pci_init: Fold fsl_pci_setup_inbound_windows into fsl_pci_init
Every platform that calls fsl_pci_init calls fsl_pci_setup_inbound_windows
before it calls fsl_pci_init. There isn't any reason to just call it
from fsl_pci_init and simplify things a bit.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Kumar Gala [Tue, 4 Aug 2009 01:44:55 +0000 (20:44 -0500)]
pci/fsl_pci_init: Fold pci_setup_indirect into fsl_pci_init
Every platform that calls fsl_pci_init calls pci_setup_indirect before
it calls fsl_pci_init. There isn't any reason to just call it from
fsl_pci_init and simplify things a bit.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Also make bootdelay consistent with other boards, so as to give on the
opportunity to fix mistakenly set bootcmd without having checked for an
bootdelay zero setting first.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Sandeep Paulraj [Mon, 10 Aug 2009 17:27:56 +0000 (13:27 -0400)]
MTD:NAND: ADD new ECC mode NAND_ECC_HW_OOB_FIRST
This patch adds the new mode NAND_ECC_HW_OOB_FIRST in the nand code to
support 4-bit ECC on TI DaVinci devices with large page (up to 2K) NAND
chips. This ECC mode is similar to NAND_ECC_HW, with the exception of
read_page API that first reads the OOB area, reads the data in chunks,
feeds the ECC from OOB area to the ECC hw engine and perform any
correction on the data as per the ECC status reported by the engine.
This patch has been accepted by Andrew Morton and can be found at
Ilya Yanok [Mon, 10 Aug 2009 22:32:54 +0000 (02:32 +0400)]
mxc_nand: add nand driver for MX2/MX3
Driver for NFC NAND controller found on Freescale's MX2 and MX3
processors. Ported from Linux. Tested only with i.MX27 but should
works with other MX2 and MX3 processors too.
Signed-off-by: Ilya Yanok <yanok@emcraft.com> Signed-off-by: Scott Wood <scottwood@freescale.com>
Sandeep Paulraj [Mon, 10 Aug 2009 17:27:46 +0000 (13:27 -0400)]
NAND: ADD page Parameter to all read_page/read_page_raw API's
This patch adds a new "page" parameter to all NAND read_page/read_page_raw
APIs. The read_page API for the new mode ECC_HW_OOB_FIRST requires the
page information to send the READOOB command and read the OOB area before
the data area.
This patch has been accepted by Andrew Morton and can be found at
http://userweb.kernel.org/~akpm/mmotm/broken-out/mtd-nand-add-page-parameter-to-all-read_page-read_page_raw-apis.patch
WE would like this to become part of the u-boot GIT as well
Change %08lX to %08X in board.c. Remove unused variable
'oscillator' in mcf5227x/cpu_init.c and 'scm2' in
mcf532x/cpu_init.c. Provide argument type cast in
drivers/dma/MCD_dmaApi.c.
ColdFire: Fix missing _IO_BASE which caused compile error
The compile error was caused by a recent patch. Affected platforms -
M5253DEMO.h, M5253EVBE.h, and M54455EVB.h. Adding the _IO_BASE
automatically defined to 0 in asm-m68k/io.h if it isn't set in
platform configuration file.
Kim Phillips [Mon, 24 Aug 2009 19:32:26 +0000 (14:32 -0500)]
net: tsec - handle user interrupt while waiting for PHY auto negotiation to complete
if you don't have firmware installed for the PHY to come to life, this
wait can be painful - let's give the option to avoid it if we want.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com> Acked-by: Andy Fleming <afleming@freescale.com> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Robin Getz [Thu, 20 Aug 2009 14:50:20 +0000 (10:50 -0400)]
Add Transfer Size Option to tftp
Optionally add RFC 2349 "Transfer Size Option", so we can minimize the
time spent sending data over the UART (now print a single line during a
tftp transfer).
- If turned on (CONFIG_TFTP_TSIZE), U-Boot asks for the size of the file.
- if receives the file size, a single line (50 chars) are printed.
one hash mark == 2% of the file downloaded.
- if it doesn't receive the file size (the server doesn't support RFC
2349, prints standard hash marks (one mark for each UDP frame).
Signed-off-by: Robin Getz <rgetz@blackfin.uclinux.org> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Ben Warren [Tue, 25 Aug 2009 20:09:37 +0000 (13:09 -0700)]
Convert CS8900 Ethernet driver to CONFIG_NET_MULTI API
All in-tree boards that use this controller have CONFIG_NET_MULTI added
Also:
- changed CONFIG_DRIVER_CS8900 to CONFIG_CS8900
- changed CS8900_BASE to CONFIG_CS8900_BASE
- changed CS8900_BUS?? to CONFIG_CS8900_BUS??
- cleaned up line lengths
- modified VCMA9 command function that accesses the device
- removed MAC address initialization from lib_arm/board.c
Signed-off-by: Ben Warren <biggerbadderben@gmail.com> Tested-by: Wolfgang Denk <wd@denx.de> Acked-by: Wolfgang Denk <wd@denx.de>
To take advantage of defragmented packets, the config file
can define CONFIG_NFS_READ_SIZE to override the 1kB default.
No support is there for an environment variable by now.
Signed-off-by: Alessandro Rubini <rubini@gnudd.com> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
tftp: get the tftp block size from config file and from the environment
Increasing the block size is useful if CONFIG_IP_DEFRAG is
used. Howerver, the last fragments in a burst may overflow the
receiving ethernet, so the default is left at 1468, with thre new
CONFIG_TFTP_BLOCKSIZE for config files. Further, "tftpblocksize"
can be set in the environment.
Signed-off-by: Alessandro Rubini <rubini@gnudd.com> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
The defragmenting code is enabled by CONFIG_IP_DEFRAG; the code is
useful for TFTP and NFS transfers. The user can specify the maximum
defragmented payload as CONFIG_NET_MAXDEFRAG (default 16k).
Since NFS has a bigger per-packet overhead than TFTP, the static
reassembly buffer can hold CONFIG_NET_MAXDEFRAG + the NFS overhead.
The packet buffer is used as an array of "hole" structures, acting as
a double-linked list. Each new fragment can split a hole in two,
reduce a hole or fill a hole. No support is there for a fragment
overlapping two diffrent holes (i.e., thre new fragment is across an
already-received fragment).
Signed-off-by: Alessandro Rubini <rubini@gnudd.com> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Feng Kan [Fri, 21 Aug 2009 17:59:42 +0000 (10:59 -0700)]
ppc4xx: Fix ECC Correction bug with SMC ordering for NDFC driver
Fix ECC Correction bug where the byte offset location were double
flipped causing correction routine to toggle the wrong byte location
in the ECC segment. The ndfc_calculate_ecc routine change the order
of getting the ECC code.
/* The NDFC uses Smart Media (SMC) bytes order */
ecc_code[0] = p[2];
ecc_code[1] = p[1];
ecc_code[2] = p[3];
But in the Correction algorithm when calculating the byte offset
location, the s1 is used as the upper part of the address. Which
again reverse the order making the final byte offset address
location incorrect.
byteoffs = (s1 << 0) & 0x80;
.
.
byteoffs |= (s0 >> 4) & 0x08;
The order is change to read it in straight and let the correction
function to revert it to SMC order.
Signed-off-by: Feng Kan <fkan@amcc.com> Acked-by: Victor Gallardo <vgallardo@amcc.com> Acked-by: Prodyut Hazarika <phazarika@amcc.com> Signed-off-by: Stefan Roese <sr@denx.de>
Eric Millbrandt [Thu, 13 Aug 2009 13:32:37 +0000 (08:32 -0500)]
Add support for USB on PSC3 for the mpc5200
Support USB on PSC3 on the mpc5200. Before this patch, enabling USB support
would reconfigure PSC4 and PSC5 to USB. The mpc5200 does not support USB
enabled on both the standard USB port and PSC3. This patch masks the
appropriate bits when enabling USB.
Signed-off-by: Eric Millbrandt <emillbrandt@dekaresearch.com> Acked-by: Grant Likely <grant.likely@secretlab.ca> Acked-by: Remy Bohmer <linux@bohmer.net>
Albin Tonnerre [Thu, 13 Aug 2009 13:31:11 +0000 (15:31 +0200)]
Replace BCD2BIN and BIN2BCD macros with inline functions
In the process, also remove backward-compatiblity macros BIN_TO_BCD and
BCD_TO_BIN and update the sole board using them to use the new bin2bcd
and bcd2bin instead
Mike Frysinger [Fri, 24 Jul 2009 20:34:32 +0000 (16:34 -0400)]
unify {CONFIG_,}ENV_IS_EMBEDDED
Some boards have fallen out of sync by defining CONFIG_ENV_IS_EMBEDDED
manually. While it is useful to have this available to the build system,
let's do it automatically rather than forcing people to opt into it.
Signed-off-by: Mike Frysinger <vapier@gentoo.org> Signed-off-by: Albin Tonnerre <albin.tonnerre@free-electrons.com> Signed-off-by: Wolfgang Denk <wd@denx.de>
Mike Frysinger [Sun, 23 Aug 2009 06:47:59 +0000 (02:47 -0400)]
start a linker script helper file
Start a common header file for common linker script code (such as
workarounds for older linkers) rather than doing this in the build system.
As fallout, we no longer execute the linker every time config.mk is
included by a build file (which can easily be 70+ times), but rather only
execute it once.
This also fixes a bug in the major version checking by creating a macro to
easily compare versions and keep people from making the same common
mistake (forgetting to check major and minor together).
commit 9993e196da707a0a1cd4584f1fcef12382c1c144 "mpc83xx: convert all
remaining boards over to 83XX_GENERIC_PCI" remapped pci windows on
tqm834x to make it more consistent with the other 83xx boards. During
that time however, the author failed to realize that FLASH_BASE was
occupying the same range as what PCI1_MEM_BASE was being assigned.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com> Tested-by: Wolfgang Denk <wd@denx.de>
Paul Gortmaker [Fri, 21 Aug 2009 21:21:58 +0000 (16:21 -0500)]
mpc83xx: sbc8349 - make enabling PCI more user friendly
Prior to this commit, to enable PCI, you had to go manually
edit the board config header, which isn't really user friendly.
This adds the typical PCI make targets to the toplevel Makefile
in accordance with what is being done with other boards.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
This patch fixes some issues with JFFS2 summary support in U-Boot.
1/ Summary support made compilation configurable (as summary support
considered expiremental even in Linux).
2/ Summary code can do unaligned 16-bit and 32-bit memory accesses.
We need to get data byte by byte to exclude data aborts.
3/ Make summary scan in two passes so we can safely fall back to full
scan if we found unsupported entry in the summary.
projects / u-boot.git / log