Eric Nelson [Sat, 8 Mar 2014 14:55:52 +0000 (07:55 -0700)]
cfb_console: align fields in gzipped .bmp files
.bmp files contain 32-bit integers aligned at offsets of +2, +6,
et cetera within the bmp_header structure (see include/bmp_layout.h).
Support for gzip-compressed .bmp files is present in the cfb_console
display subsystem by uncompressing them prior to use.
This patch forces the in-memory header to be aligned properly
for these compressed images by extracting them to a 2-byte
offset in the memory returned by malloc. Since malloc will always
return a 4-byte aligned value, this forces the .bmp header
fields to be naturally aligned on 4-byte addresses.
Refer to these files for more details:
doc/README.displaying-bmps
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Ian Campbell [Fri, 7 Mar 2014 01:20:58 +0000 (01:20 +0000)]
ahci: wait longer for link.
I have observed timeouts on a cubietruck.
The increase to 40ms is completely arbitrary and Works For Me(tm). I
couldn't find a good reference for how long you are supposed to wait,
although googling around it seems like tens of ms rather than single
digits is more common. I don't think there is any harm in waiting a bit
longer.
Priyanka Jain [Wed, 26 Feb 2014 04:08:37 +0000 (09:38 +0530)]
powerpc/t104xrdb: Update DDR initialization related settings
Update following DDR related settings for T1040RDB, T1042RDB_PI
-Correct number of chip selects to two as t1040 supports
two Chip selects.
-Update board_specific_parameters udimm structure with settings
derived via calibration.
-Update ddr_raw_timing sructure corresponding to DIMM.
-Set ODT to off. Typically on FSL board, ODT is set to 75 ohm,
but on T104xRDB, on setting this , DDR instability is observed.
Board-level debugging is in progress.
Verified the updated settings to be working fine with dual-ranked
Micron, MT18KSF51272AZ-1G6 DIMM at data rate 1600MT/s.
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com> Signed-off-by: York Sun <yorksun@freescale.com>
Priyanka Jain [Wed, 26 Feb 2014 10:41:53 +0000 (16:11 +0530)]
powerpc/t1040qds: Add Video - HDMI support
T1040 has internal display interface unit (DIU) for driving video.
T1040QDS supports video mode via
-LCD using TI enconder
-HDMI type interface via HDMI encoder
Chrontel, CH7301C encoder which is I2C programmable is used as
HDMI connector on T1040QDS.
This patch add support to
-enable Video interface for T1040QDS
-route qixis multiplexing to enable DIU-HDMI interface on board
-program DIU pixel clock gerenartor for T1040
-program HDMI encoder via I2C on board
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
Priyanka Jain [Thu, 30 Jan 2014 10:09:58 +0000 (15:39 +0530)]
powerpc/mpc85xx: Add SCFG_PIXCLKCR register support for T1040
T1040 SoC has SCFG (Supplement Configuration) Block which provides
chip specific configuration and status support. The base address of
SCFG block in T1040 is 0xfc000.
SCFG contains SCFG_PIXCLKCR (DIU pixel clock control register)
at offset 0x28.
Add definition of
-SCFG block
-SCFG_PIXCLKCR register
-Bits definition of SCFG_PIXCLK register
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
Mela Custodio [Wed, 19 Feb 2014 15:16:57 +0000 (00:16 +0900)]
bootstage: powerpc: support fdt stash and reporting
This implements stashing of bootstage timing data to FDT and automatic
timing reporting. To enable define CONFIG_BOOTSTAGE_FDT and
CONFIG_BOOTSTAGE_REPORT respectively.
Signed-off-by: Rommel G Custodio <sessyargc+u-boot@gmail.com> Reviewed-by: York Sun <yorksun@freescale.com>
USB spec says that the minimum disconnect threshold should be
over 525 mV. However, internal USB PHY threshold value is below
this specified value. Due to this some devices disconnect at
run-time. Hence, phy settings are tweaked to increased disconnect
threshold to be above 525mV by using this workaround.
Signed-off-by: Suresh Gupta <suresh.gupta@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
Shaveta Leekha [Wed, 26 Feb 2014 10:38:22 +0000 (16:08 +0530)]
powerpc/b4860: Add workaround for errata A006384 and A006475
SerDes PLLs may not lock reliably at 5 G VCO configuration(A006384)
and at cold temperatures(A006475), workaround recalibrate the
PLLs with some SerDes configuration
Both these errata are only applicable for b4 rev1.
So, make workaround for these errata conditional,
depending upon soc version.
Signed-off-by: Shaveta Leekha <shaveta@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
Shaveta Leekha [Wed, 26 Feb 2014 10:37:51 +0000 (16:07 +0530)]
B4860qds: Set SerDes2 refclk2 at to 156.25MHz for XFI to work
Change setting of SerDes2 refclk2 to have the default value as it is
coming on board that is 156.25MHz, for XFI to work.
Also change PLL_NUM variable to the one defined in config_mpc85xx.h
for B4860 and B4420.
Signed-off-by: Shaveta Leekha <shaveta@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
Shaveta Leekha [Wed, 26 Feb 2014 10:36:56 +0000 (16:06 +0530)]
board/b4860qds: Add support to make PCIe SATA work on B4860QDS
1) SerDes2 Refclks have been set properly to make
PCIe SATA to work as it work on SerDes refclk of 100MHz
2) Mask the SerDes's device reset request before changing
the Refclks for SerDes1 and SerDes2 for PLL locks to
happen properly, device reset request bit unmasked
after SerDes refclks configuration
Signed-off-by: Shaveta Leekha <shaveta@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
Shaveta Leekha [Wed, 26 Feb 2014 10:36:30 +0000 (16:06 +0530)]
board/b4860qds: Add support to make Aurora work on B4860QDS
1) Add new SerDes1 protocols having Aurora in them
2) Add VSC cross point connections for Aurora to work with
CPRI and SGMIIs
3) Configure VSC crossbar switch to connect SerDes1
lanes to aurora on board, by checking SerDes1 protocols
4) SerDes1 Refclks have been set properly to make
Aurora, CPRI and SGMIIs to work together properly
Signed-off-by: Shaveta Leekha <shaveta@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
Masahiro Yamada [Wed, 5 Mar 2014 08:40:10 +0000 (17:40 +0900)]
powerpc: mpc8260: consolidate CONFIG_MPC8260 and CONFIG_8260
Before this commit, CONFIG_MPC8260 and CONFIG_8260
were used mixed-up.
All boards with mpc8260 cpu defined both of them:
- CONFIG_MPC8260 was defined in board config headers
and include/common.h
- CONFIG_8260 was defined arch/powerpc/cpu/mpc8260/config.mk
We do not need to have both of them.
This commit keeps only CONFIG_MPC8260.
This commit does:
- Delete CONFIG_8260 and CONFIG_MPC8260 definition
in config headers and include/common.h
- Rename CONFIG_8260 to CONFIG_MPC8260
in arch/powerpc/cpu/mpc8260/config.mk.
- Rename #ifdef CONFIG_8260 to #ifdef CONFIG_MPC8260
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Cc: Wolfgang Denk <wd@denx.de>
Masahiro Yamada [Wed, 5 Mar 2014 08:25:37 +0000 (17:25 +0900)]
mips: move CONFIG_MIPS{32, 64} definition to config.mk
All mips32 boards define CONFIG_MIPS32 in config headers
except malta boards which define it in boards.cfg.
We can consolidate them by defining it in
arch/mips/cpu/mips32/config.mk.
CONFIG_MIPS64 definition can be moved to
arch/mips/cpu/mips64/config.mk as well.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com> Acked-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Masahiro Yamada [Wed, 5 Mar 2014 07:59:40 +0000 (16:59 +0900)]
kbuild: improve Kbuild speed
Kbuild brought about many advantages for us but a significant
performance regression was reported by Simon Glass.
After some discussions and analysis, it turned out
its main cause is in $(call cc-option,...).
Historically, U-Boot parses all config.mk
(arch/*/config.mk and board/*/config.mk)
every time descending into subdirectories.
That means cc-options are evaluated over and over again.
$(call cc-option,...) is useful but costly.
So we want to evaluate them only in ./Makefile
and spl/Makefile and export compiler flags.
This commit changes the build system as follows:
- Modify scripts/Makefile.build to not include config.mk
Instead, add $(PLATFORM_CPPFLAGS) to asflags-y, ccflags-y,
cppflags-y.
- Export many variables
Going forward, Kbuild will not parse config.mk files
when it descends into subdirectories.
If we want to set variables in config.mk and use them
in subdirectories, they must be exported.
This is the list of variables to get exported:
PLATFORM_CPPFLAGS
CPUDIR
BOARDDIR
OBJCOPYFLAGS
LDFLAGS
LDFLAGS_FINAL
(used in nand_spl/board/*/*/Makefile)
CONFIG_STANDALONE_LOAD_ADDR
(used in examples/standalone/Makefile)
SYM_PREFIX
(used in examples/standalone/Makefile)
RELFLAGS
(used in examples/standalone/Makefile)
- Delete CPPFLAGS
This variable has been replaced with PLATFORM_CPPFLAGS
- Copy gcclibdir from example/standalone/Makefile
to arch/sparc/config.mk
The reference in CONFIG_STANDALONE_LOAD_ADDR must be
resolved before it is exported.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Reported-by: Simon Glass <sjg@chromium.org> Acked-by: Simon Glass <sjg@chromium.org> Tested-by: Simon Glass <sjg@chromium.org> [on Sandbox] Tested-by: Stephen Warren <swarren@nvidia.com> [on Tegra]
Masahiro Yamada [Wed, 5 Mar 2014 07:59:38 +0000 (16:59 +0900)]
kbuild: add CONFIG_ prefix to USE_PRIVATE_LIBGCC
Before this commit, USE_PRIVATE_LIBGCC was defined in
arch-specific config.mk and referenced in
arch/$(ARCH)/lib/Makefile.
We are not happy about parsing config.mk again and again.
We have to keep the same behavior with a different way.
By adding "CONFIG_" prefix, this macro appears
in include/autoconf.mk, include/spl-autoconf.mk.
(And treating USE_PRIVATE_LIBGCC as CONFIG macro
is reasonable enough.)
Tegra SoC family defined USE_PRIVATE_LIBGCC as "yes"
in arch/arm/cpu/arm720t/tegra*/config.mk,
whereas did not define it in arch/arm/cpu/armv7/tegra*/config.mk.
It means Tegra enables PRIVATE_LIBGCC only for SPL.
We can describe the same behavior by adding
Many (but not all) of Blackfin boards give -O2 option
to compile under lib/ directory.
That means lib/ should be speed-optimized,
whereas other parts should be size-optimized.
We want to keep the same behavior,
but do not want to parse board/*/config.mk again and again.
We've got no choice but to invent a new method.
CONFIG_CC_OPTIMIZE_LIBS_FOR_SPEED, if it is enabled,
gives -O2 flag only for building under lib/ directory.
Dirty codes which I had marked as "FIX ME"
in board/${BOARD}/config.mk have been deleted.
Instead, CONFIG_CC_OPTIMIZE_LIBS_FOR_SPEED has been
defined in include/configs/${BOARD}.h.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Cc: Sonic Zhang <sonic.zhang@analog.com>
Tom Rini [Tue, 4 Mar 2014 20:52:35 +0000 (15:52 -0500)]
cmd_nvedit: Make 'env import -c' require size parameter
When importing a checksummed area we need to be told how big the area in
question is so that we know that will match the size of the area which
the checksum is generated against.
Reported-by: Pierre AUBERT <p.aubert@staubli.com> Signed-off-by: Tom Rini <trini@ti.com>
Stefan Roese [Tue, 4 Mar 2014 14:34:35 +0000 (15:34 +0100)]
ppc4xx: Remove 4xx NAND booting support
As ppc4xx currently only supports the deprecated nand_spl infrastructure
and nobody seems to have time / resources to port this over to the newer
SPL infrastructure, lets remove NAND booting completely.
This should not affect the "normal", non NAND-booting ppc4xx platforms
that are currently supported.
Signed-off-by: Stefan Roese <sr@denx.de> Cc: Wolfgang Denk <wd@denx.de> Cc: Tirumala Marri <tmarri@apm.com> Cc: Matthias Fuchs <matthias.fuchs@esd.eu> Cc: Masahiro Yamada <yamada.m@jp.panasonic.com> Cc: Tom Rini <trini@ti.com> Tested-by: Matthias Fuchs <matthias.fuchs@esd.eu>
Stephen Warren [Sun, 2 Mar 2014 05:18:00 +0000 (22:18 -0700)]
unit-test: make "test -e" test independent of $CWD
The unit-test for hush's "test -e" currently relies upon being run in
the U-Boot build directory, because it tests for the existence of a file
that exists in that directory.
Fix this by explicitly creating the file we use for the existence test,
and deleting it afterwards so that multiple successive unit-test
invocations succeed. This required adding an os.c function to erase
files.
Reported-by: Simon Glass <sjg@chromium.org> Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Stephen Warren [Sun, 2 Mar 2014 05:16:10 +0000 (22:16 -0700)]
hush: fix some quoted variable expansion issues
The following shell command fails:
if test -z "$x"; then echo "zero"; else echo "non-zero"; fi
(assuming $x does not exist, it prints "non-zero" rather than "zero").
... since "$x" expands to nothing, and the argument is completely
dropped, causing too few to be passed to -z, causing cmd_test() to
error out early.
This is because when variable expansions are processed by make_string(),
the expanded results are concatenated back into a new string. However,
no quoting is applied when doing so, so any empty variables simply don't
generate any parameter when the combined string is parsed again.
Fix this by explicitly replacing quoting any argument that was originally
quoted when re-generating a string from the already-parsed argument list.
This also fixes loss of whitespace in commands such as:
setenv space " "
setenv var " 1${space}${space} 2 "
echo ">>${var}<<"
Reported-by: Russell King <linux@arm.linux.org.uk> Acked-by: Simon Glass <sjg@chromium.org> Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Stephen Warren [Fri, 28 Feb 2014 05:01:28 +0000 (22:01 -0700)]
unit-test: clean up evironment after Hush tests
Delete the temporary variables that are used to save unit-test results
from the environment after running the test. This prevents polluting
the environment, or growing it too much.
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org> Acked-by: Simon Glass <sjg@chromium.org>
Stephen Warren [Thu, 27 Feb 2014 20:27:02 +0000 (13:27 -0700)]
net: asix: don't pad odd-length TX packets
For Ethernet/USB RX packets, the ASIX HW pads odd-sized packets so that
they have an even size. Currently, asix_recv() does remove this padding,
and asic_send() adds equivalent padding in the TX path. However, the HW
does not appear to need this packing for TX packets in practical testing
with "ASIX Elec. Corp. AX88x72A 000001" Vendor: 0x0b95 Product 0x7720
Version 0.1. The Linux kernel does no such padding for the TX path.
Remove the padding from the TX path:
* For consistency with the Linux kernel.
* NVIDIA has a Tegra simulator which validates that the length of USB
packets sent to an ASIX device matches the packet length value inside
the packet data. Having U-Boot and the kernel do the same thing when
creating the TX packets simplifies the simulator's validation.
Cc: Lucas Stach <dev@lynxeye.de> Cc: Marek Vasut <marex@denx.de> Cc: Simon Glass <sjg@chromium.org> Signed-off-by: Stephen Warren <swarren@nvidia.com> Acked-by: Simon Glass <sjg@chromium.org> Acked-by: Marek Vasut <marex@denx.de> Tested-by: Marek Vasut <marex@denx.de> Tested-by: Gerhard Sittig <gsi@denx.de>
pekon gupta [Fri, 22 Nov 2013 11:23:30 +0000 (16:53 +0530)]
mtd: nand: omap: move omap_elm.h from arch/arm/include/asm to drivers/mtd/nand
omap_elm.h is a generic header used by OMAP ELM driver for all TI platfoms.
Hence this file should be present in generic folder instead of architecture
specific include folder.
Build tested using: ./MAKEALL -s am33xx -s omap3 -s omap4 -s omap5
pekon gupta [Fri, 22 Nov 2013 11:23:29 +0000 (16:53 +0530)]
mtd: nand: omap: move omap_gpmc.h from arch/arm/include/asm to drivers/mtd/nand
omap_gpmc.h is a generic header used by OMAP NAND driver for all TI platfoms.
Hence this file should be present in generic folder instead of architecture
specific include folder.
Build tested using: ./MAKEALL -s am33xx -s omap3 -s omap4 -s omap5
pekon gupta [Fri, 22 Nov 2013 11:23:28 +0000 (16:53 +0530)]
mtd: nand: omap: merge duplicate GPMC data from different arch-xx headers into common omap_gpmc.h
Each SoC platform (AM33xx, OMAP3, OMAP4, OMAP5) has its own copy of GPMC related
defines and declarations scattered in SoC platform specific header files
like include/asm/arch-xx/cpu.h
However, GPMC hardware remains same across all platforms thus this patch merges
GPMC data scattered across different arch-xx specific header files into single
header file include/asm/arch/omap_gpmc.h
pekon gupta [Fri, 22 Nov 2013 11:23:27 +0000 (16:53 +0530)]
mtd: nand: omap: remove unused #defines from common omap_gpmc.h
OMAP NAND driver can detect Page-size and OOB-size of NAND device from ONFI
params or nand_id[] table. And based on that it defines ECC layout.
This patch
1) removes following board configs used for defining NAND ECC layout
- GPMC_NAND_ECC_LP_x16_LAYOUT (for large page x16 NAND)
- GPMC_NAND_ECC_LP_x8_LAYOUT (for large page x8 NAND)
- GPMC_NAND_ECC_SP_x16_LAYOUT (for small page x16 NAND)
- GPMC_NAND_ECC_SP_x8_LAYOUT (for small page x8 NAND)
2) removes unused #defines in common omap_gpmc.h depending on above configs
pekon gupta [Fri, 22 Nov 2013 11:23:26 +0000 (16:53 +0530)]
mtd: nand: omap: remove redundant platform specific header: arch-xx/omap_gpmc.h
Currently there are two sets of omap_gpmc.h header files
(a) arch/arm/include/asm/omap_gpmc.h
common header file for all platforms, containing defines and declarations used
by GPMC NAND driver.
(b) arch/arm/include/asm/arch-xx/omap_gpmc.h
SoC platform specific header file containing defines like ECC layout.
This patch removes platform specific arch-xx/omap_gpmc.c because:
- GPMC hardware engine is common for all SoC platforms hence only (a) is enough
- ECC layout is now defined in omap_nand.c driver itself based on ecc-scheme
selected. Hence all ECC layout declarations in (b) are redundant.
James Hogan [Tue, 4 Mar 2014 14:48:42 +0000 (14:48 +0000)]
malta: correct tcl script path in README.malta
README.malta referred to board/malta, but malta has now been moved
within board/imgtec/, so correct the path.
Signed-off-by: James Hogan <james.hogan@imgtec.com> Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com> Cc: Paul Burton <paul.burton@imgtec.com>
Masahiro Yamada [Mon, 3 Mar 2014 10:03:17 +0000 (19:03 +0900)]
kbuild: allow empty board directories
U-Boot has compelled all boards to have
board/${BOARD}/ or board/${VENDOR}/${BOARD}/ directory.
Sometimes it does not seem suitable for some boards,
for example Sandbox. (Is it a board?)
And arcangel4 board has nothing to compile
under the board directory.
This commit makes the build system more flexible:
If '<none>' is given to the 6th column (=Board name) of boards.cfg,
Kbuild will not descend into the board directory.
Tom Rini [Thu, 27 Feb 2014 13:27:28 +0000 (08:27 -0500)]
scripts: update checkpatch.pl to latest upstream version
Update to v3.14-rc4's version of checkpatch.pl. In doing so we drop the
changes to top_of_kernel_tree() as we pass in --no-tree and drop our
changes about MAINTAINERS as that's for reporting checkpatch.pl problems
itself (and upstream has said they'll reword this section to be
clearer).
Simon Glass [Wed, 26 Feb 2014 22:59:27 +0000 (15:59 -0700)]
dm: Remove old driver model documentation
This documentation pertains to the planned implementation of driver model
in U-Boot for each subsystem, but it has not been superseded. It is
probably better to have this documentation in the source code for each
subsystem where possible, so that docbook will pick it up. Where this does
not make sense, new documentation can be placed in some suitable file in
doc/driver-model.
Simon Glass [Wed, 26 Feb 2014 22:59:26 +0000 (15:59 -0700)]
dm: Enable gpio command to support driver model
Now that named GPIO banks are supported, along with a way of obtaining
the status of a GPIO (input or output), we can provide an enhanced
GPIO command for driver model. Where the driver provides its own operation
for obtaining the GPIO state, this is used, otherwise a generic version
is sufficient.
Simon Glass [Wed, 26 Feb 2014 22:59:24 +0000 (15:59 -0700)]
dm: Add GPIO support and tests
Add driver model support for GPIOs. Since existing GPIO drivers do not use
driver model, this feature must be enabled by CONFIG_DM_GPIO. After all
GPO drivers are converted over we can perhaps remove this config.
Tests are provided for the sandbox implementation, and are a sufficient
sanity check for basic operation.
The GPIO uclass understands the concept of named banks of GPIOs, with each
GPIO device providing a single bank. Within each bank the GPIOs are numbered
using an offset from 0 to n-1. For example a bank named 'b' with 20
offsets will provide GPIOs named b0 to b19.
Anonymous GPIO banks are also supported, and are just numbered without any
prefix.
Each time a GPIO driver is added to the uclass, the GPIOs are renumbered
accordinging, so there is always a global GPIO numbering order.
Signed-off-by: Simon Glass <sjg@chromium.org> Signed-off-by: Marek Vasut <marex@denx.de> Signed-off-by: Pavel Herrmann <morpheus.ibis@gmail.com> Signed-off-by: Viktor Křivák <viktor.krivak@gmail.com> Signed-off-by: Tomas Hlavacek <tmshlvck@gmail.com>
Simon Glass [Wed, 26 Feb 2014 22:59:23 +0000 (15:59 -0700)]
dm: Add a demonstration/example driver
As an example of how to write a uclass and a driver, provide a demo version
of each, accessible through the 'demo' command.
To use these with driver model, define CONFIG_CMD_DEMO and CONFIG_DM_DEMO.
The two demo drivers are enabled with CONFIG_DM_DEMO_SIMPLE and
CONFIG_DM_DEMO_SHAPE.
Signed-off-by: Simon Glass <sjg@chromium.org> Signed-off-by: Marek Vasut <marex@denx.de> Signed-off-by: Pavel Herrmann <morpheus.ibis@gmail.com> Signed-off-by: Viktor Křivák <viktor.krivak@gmail.com> Signed-off-by: Tomas Hlavacek <tmshlvck@gmail.com>
Simon Glass [Wed, 26 Feb 2014 22:59:22 +0000 (15:59 -0700)]
dm: Add a 'dm' command for testing
This command is not required for driver model operation, but can be useful
for testing. It provides simple dumps of internal data structures.
Signed-off-by: Simon Glass <sjg@chromium.org> Signed-off-by: Marek Vasut <marex@denx.de> Signed-off-by: Pavel Herrmann <morpheus.ibis@gmail.com> Signed-off-by: Viktor Křivák <viktor.krivak@gmail.com> Signed-off-by: Tomas Hlavacek <tmshlvck@gmail.com>
Simon Glass [Wed, 26 Feb 2014 22:59:21 +0000 (15:59 -0700)]
dm: Add basic tests
Add some tests of driver model functionality. Coverage includes:
- basic init
- binding of drivers to devices using platform_data
- automatic probing of devices when referenced
- availability of platform data to devices
- lifecycle from bind to probe to remove to unbind
- renumbering within a uclass when devices are probed/removed
- calling driver-defined operations
- deactivation of drivers when removed
- memory leak across creation and destruction of drivers/uclasses
- uclass init/destroy methods
- automatic probe/remove of children/parents when needed
This function is enabled for sandbox, using CONFIG_DM_TEST.
Simon Glass [Wed, 26 Feb 2014 22:59:20 +0000 (15:59 -0700)]
dm: Set up driver model after relocation
Make driver model available after relocation, by setting up data structures
and scanning for devices using compiled-in platform_data and (when available)
the device tree.
Simon Glass [Wed, 26 Feb 2014 22:59:18 +0000 (15:59 -0700)]
dm: Add base driver model support
Add driver model functionality for generic board.
This includes data structures and base code for registering devices and
uclasses (groups of devices with the same purpose, e.g. all I2C ports will
be in the same uclass).
The feature is enabled with CONFIG_DM.
Signed-off-by: Simon Glass <sjg@chromium.org> Signed-off-by: Marek Vasut <marex@denx.de> Signed-off-by: Pavel Herrmann <morpheus.ibis@gmail.com> Signed-off-by: Viktor Křivák <viktor.krivak@gmail.com> Signed-off-by: Tomas Hlavacek <tmshlvck@gmail.com>
Simon Glass [Wed, 26 Feb 2014 22:59:16 +0000 (15:59 -0700)]
yaffs: Remove private list implementation
U-Boot already has a list implementation, and files which include both
that and the yaffs implementation will get errors:
In file included from ydirectenv.h:80:0,
from yportenv.h:81,
from yaffs_guts.h:19,
from yaffs_allocator.h:19,
from yaffs_allocator.c:14:
yaffs_list.h:32:8: error: redefinition of ‘struct list_head’
struct list_head {
^
Simon Glass [Wed, 26 Feb 2014 22:59:15 +0000 (15:59 -0700)]
Add cmd_process_error() to report and process errors
U-Boot now uses errors defined in include/errno.h which are negative
integers. Commands which fail need to report the error and return 1
to indicate failure. Add this functionality in cmd_process_error().
For now this merely reports the error number. It would be possible
also to produce a helpful error message by storing the error strings
in U-Boot.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com> Cc: Vineet Gupta <vgupta@synopsys.com> Cc: Tom Rini <trini@ti.com> Cc: Stefan Roese <sr@denx.de> Cc: Albert Aribaud <albert.u.boot@aribaud.net> Acked-by: Tom Rini <trini@ti.com> Acked-by: Stefan Roese <sr@denx.de>
[trini: Add bcm Kona platforms to the patch] Signed-off-by: Tom Rini <trini@ti.com>
Masahiro Yamada [Wed, 26 Feb 2014 08:51:11 +0000 (17:51 +0900)]
nand_spl: display warning message to inform the end of nand_spl
Now we have two different frameworks for doing the same thing.
I'd like to propose to drop nand_spl framework.
How about deleting it before v2014.07 release?
In the interim, this commit will display a warning message
when compiling nand_spl board.
They must be ported to SPL before the deadline,
otherwise they will be removed.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Cc: Dave Liu <daveliu@freescale.com> Cc: Ron Madrid <info@sheldoninst.com> Cc: Roy Zang <tie-fei.zang@freescale.com> Cc: Stefan Roese <sr@denx.de> Acked-by: Stefan Roese <sr@denx.de>
pekon gupta [Tue, 19 Nov 2013 05:32:17 +0000 (11:02 +0530)]
mtd: nand: omap: optimized chip->ecc.correct() for H/W ECC schemes
chip->ecc.correct() is used for detecting and correcting bit-flips during read
operations. In omap-nand driver it implemented as:
(a) omap_correct_data(): for h/w based ECC_HAM1 scheme
(b) omap_correct_data_bch() + CONFIG_NAND_OMAP_ECC_BCH8_CODE_HW_DETECTION_SW
for ECC_BCH8 scheme using GPMC and software lib/bch.c
(c) omap_correct_data_bch() + CONFIG_NAND_OMAP_ECC_BCH8_CODE_HW
for ECC_BCH8 scheme using GPMC and ELM
This patch updates (c)
- checks for calc_ecc[]==0x00 so that error_correction is not required for
known good pages.
- adds scalability for other ECC_BCHx scheme by merging following
omap_rotate_ecc_bch() + omap_fix_errors_bch() => omap_correct_data_bch()
- fixing logic for bit-flip correction based on error_loc[count]
pekon gupta [Tue, 19 Nov 2013 05:32:16 +0000 (11:02 +0530)]
mtd: nand: omap: optimize chip->ecc.calculate() for H/W ECC schemes
chip->ecc.calculate() is used for calculating and fetching of ECC syndrome by
processing the data passed during Read/Write accesses.
All H/W based ECC schemes use GPMC controller to calculate ECC syndrome.
But each BCHx_ECC scheme has its own implemetation of post-processing and
fetching ECC syndrome from GPMC controller.
This patch updates OMAP_ECC_BCH8_CODE_HW ECC scheme in following way:
- merges multiple chip->calculate API for different ECC schemes
omap_calculate_ecc() + omap_calculate_ecc_bch() + omap_calculate_ecc_bch_sw()
==> omap_calculate_ecc()
- removes omap_ecc_disable() and instead uses it as inline.
pekon gupta [Tue, 19 Nov 2013 05:32:15 +0000 (11:02 +0530)]
mtd: nand: omap: optimize chip->ecc.hwctl() for H/W ECC schemes
chip->ecc.hwctl() is used for preparing the H/W controller before read/write
NAND accesses (like assigning data-buf, enabling ECC scheme configs, etc.)
Though all ECC schemes in OMAP NAND driver use GPMC controller for generating
ECC syndrome (for both Read/Write accesses). But but in current code
HAM1_ECC and BCHx_ECC schemes implement individual function to achieve this.
This patch
(1) removes omap_hwecc_init() and omap_hwecc_init_bch()
as chip->ecc.hwctl will re-initializeGPMC before every read/write call.
omap_hwecc_init_bch() -> omap_enable_ecc_bch()
(2) merges the GPMC configuration code for all ECC schemes into
single omap_enable_hwecc(), thus adding scalability for future ECC schemes.
omap_enable_hwecc() + omap_enable_ecc_bch() -> omap_enable_hwecc()
Tom Rini [Tue, 25 Feb 2014 15:27:01 +0000 (10:27 -0500)]
arm: Switch to -mno-unaligned-access when supported by the compiler
When we tell the compiler to optimize for ARMv7 (and ARMv6 for that
matter) it assumes a default of SCTRL.A being cleared and unaligned
accesses being allowed and fast at the hardware level. We set this bit
and must pass along -mno-unaligned-access so that the compiler will
still breakdown accesses and not trigger a data abort.
To better help understand the requirements of the project with respect
to unaligned memory access, the
Documentation/unaligned-memory-access.txt file has been added as
doc/README.unaligned-memory-access.txt and is taken from the v3.14-rc1
tag of the kernel.
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net> Cc: Mans Rullgard <mans@mansr.com> Signed-off-by: Tom Rini <trini@ti.com>
projects / u-boot.git / log