Peng Fan [Tue, 27 Aug 2019 06:25:27 +0000 (06:25 +0000)]
imx8m: Fix MMU table issue for OPTEE memory
When running with OPTEE, the MMU table in u-boot does not remove the OPTEE
memory from its settings. So ARM speculative prefetch in u-boot may access
that OPTEE memory. Due to trust zone is enabled by OPTEE and that memory
is set to secure access, then the speculative prefetch will fail and cause
various memory issue in u-boot.
The fail address register and int_status register in trustzone has logged
that speculative access from u-boot.
Peng Fan [Tue, 27 Aug 2019 06:24:47 +0000 (06:24 +0000)]
ddr: imx8m: fix ddr firmware location when enable SPL OF
With CONFIG_SPL_OF_CONTROL, the device tree will be padded to
end of the u-boot-spl-nodtb.bin, however we also put
the ddr firmware file to this location, so need to adapt
the code with SPL OF and align to 4 bytes to ease copy firmware.
Peng Fan [Tue, 27 Aug 2019 06:24:43 +0000 (06:24 +0000)]
tools: imx8m_image: align spl bin image size
The loader for the DDR firmware in drivers/ddr/imx/imx8m/helper.c uses a
4-byte-aligned address to load the firmware. In cases where OF is
enabled in SPL the dtb will be appended to the SPL binary and can result
in a binary that is not aligned correctly. If OF is not enabled in SPL,
`_end` is already aligned correctly, but this patch does not hurt.
To ensure the correct alignment we use dd to create a temporary file
u-boot-spl-pad.bin with the correct padding.
Since recent splash changes common code for splashscreen logo
should be used instead of adding duplicated code under board
directories. mx6ul_9x9_evk and mx6ul_14x14_evk configurations
used old board specific logo code and do not link, fix them.
Signed-off-by: Anatolij Gustschin <agust@denx.de> Acked-by: Peng Fan <peng.fan@nxp.com>
The default CSF_SIZE defined in Kconfig is too high and SPL cannot
fit into the OCRAM in certain cases.
The CSF cannot achieve 0x2000 length when using RSA 4K key which is
the largest key size supported by HABv4.
According to AN12056 "Encrypted Boot on HABv4 and CAAM Enabled Devices"
it's recommended to pad CSF binary to 0x2000 and append DEK blob to
deploy encrypted boot images.
As the maximum DEK blob size is 0x58 we can reduce CSF_SIZE to 0x2060
which should cover both CSF and DEK blob length.
Update default_image.c and image.c to align with this change and avoid
a U-Boot proper authentication failure in HAB closed devices:
Authenticate image from DDR location 0x877fffc0...
bad magic magic=0x32 length=0x6131 version=0x38
bad length magic=0x32 length=0x6131 version=0x38
bad version magic=0x32 length=0x6131 version=0x38
spl: ERROR: image authentication fail
Fixes: 96d27fb218 (Revert "habv4: tools: Avoid hardcoded CSF size for SPL targets") Reported-by: Jagan Teki <jagan@amarulasolutions.com> Signed-off-by: Breno Lima <breno.lima@nxp.com>
Patrick Wildt [Thu, 3 Oct 2019 14:08:35 +0000 (16:08 +0200)]
imx: add support for i.MX7/i.MX8MQ reset controller
Add support for the reset controller that's used on the i.MX7D
and i.MX8MQ. This will be needed to be able to assert the PCIe
reset pins. Bindings taken from Linux, driver implementation
mostly taken from Linux and adjusted to U-Boot infrastructure.
Signed-off-by: Patrick Wildt <patrick@blueri.se> Reviewed-by: Fabio Estevam <festevam@gmail.com>
Patrick Wildt [Thu, 3 Oct 2019 13:51:50 +0000 (15:51 +0200)]
imx: add support for i.MX8MQ power domain controller
Add support for the power domain controller that's used on the
i.MX8MQ. This will be needed to be able to power on the PCIe
controller. Bindings taken from Linux, driver implementation
taken from the i.MX8 power domain controller and adjusted for
the i.MX8M SoC.
mmc: Replace printf with debug call for timeouts in the i.MX28 mxs driver
This change replaces printf() with debug() for the notification about
commands timeouts.
This is done on purpose (also other drivers use such approach - dw_mmc.c,
mvebu_mmc.c), as the mmc core code (mmc.c) uses timeouts to assess if one
is using sd card or eMMC device.
In such situation timeout is a some kind of a "normal" behavior and there
shall not be any output to the console.
There is no impact on boot time for boards using this driver (even in SPL)
when two extra timeouts are returned (no SD card present, only eMMC
available).
Boot time tested with grabserial:
sudo grabserial -b 115200 -d /dev/ttyUSB1 -e 30 -t -m "^U-Boot SPL*"
spi: fix: Call mxs_reset_block() during DM/DTS probe
Without this change the DM/DTS version of mxs_spi driver doesn't reset the
SPI IP block in probe.
As a result this driver (when used solely on U-Boot proper) relies on reset
performed by mxs spi driver in SPL.
In the use case where eMMC is used in SPL as a boot primary device, the
mxs_reset_block() is not called at all and DM/DTS aware SPI driver in
U-Boot proper is malfunctioning.
dts: imx28: Remove #include "imx28.dtsi" from imx28-u-boot.dtsi file
After this change it is possible to use imx28-<board>-u-boot.dtsi with
the imx28-u-boot.dtsi explicitly included without breaking setup from
imx28-<board>.dts file.
The problem is that the imx28.dtsi included in a wrong place overrides the
changes made in imx28-<board>.dts. As a result some devices are "disabled"
in the final DTB.
imx: Introduce CONFIG_SPL_FORCE_MMC_BOOT to force MMC boot on falcon mode
This change tries to fix the following problem:
- The board boots (to be more precise - ROM loads SPL) from a slow SPI-NOR
memory.
As a result the spl_boot_device() will return SPI-NOR as a boot device
(which is correct).
- The problem is that in 'falcon boot' the eMMC is used as a boot medium to
load kernel from its partition.
Calling spl_boot_device() will break things as it returns SPI-NOR device.
To fix this issue the new CONFIG_SPL_FORCE_MMC_BOOT Kconfig flag is
introduced to handle this special use case. By default it is not defined,
so there is no change in the legacy code flow.
ARM: Update display5_factory_defconfig after switch to DM/DTS and uuu utility
This commit updates the display5_factory_defconfig file after the switch
to DM/DTS for this board.
Moreover, the VID and PID for SPL running SDP gadget have been updated to
allow seamless work with 'uuu' utility from NXP (the imx_usb doesn't work
properly after embedding the u-boot proper into fitImage - problem with IVT
embedding in FIT).
Otavio Salvador [Wed, 19 Jun 2019 18:03:44 +0000 (15:03 -0300)]
pico-imx6: Fix bootmenu handling
We should use a common script to allow booting the U-Boot console as
fallback so we ended using a 'default_boot' and 'base_boot'
environment scripts to accomplish that.
Signed-off-by: Fabio Berton <fabio.berton@ossystems.com.br> Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Default value is too high and it covers the worst case. SPL for
imx6dl_mamoj becomes too big and cannot fit into the OCRAM, but CSF size
can be reduced.
Signed-off-by: Stefano Babic <sbabic@denx.de> CC: Jagan Teki <jagan@amarulasolutions.com> CC: Breno Lima <breno.lima@nxp.com>
imx: sksimx6_defconfig: remove SPL misc option to fix build error
Remove CONFIG_SPL_DRIVERS_MISC_SUPPORT since it is already defined
in include/configs/mx6_common.h for SPL builds. When this option
is in defconfig, we get build warnings (or errors when building
with -Werror).
pico-imx7d: Add instructions for booting in Falcon mode
Improve the README by adding instructions on how to boot using
Falcon mode, which allows the SPL to load the kernel directly,
without using U-Boot proper.
Signed-off-by: Fabio Estevam <festevam@gmail.com> Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Fabio Berton [Fri, 23 Aug 2019 18:01:00 +0000 (15:01 -0300)]
pico-imx7d: Sync pico-hobbit-imx7d_defconfig
Update pico-hobbit-imx7d_defconfig using pico-imx7d_defconfig as base
to fix device tree file generation. With this all pico-imx7d are
creating u-boot-dtb.img files.
habv4: tools: Avoid hardcoded CSF size for SPL targets
Currently it's not possible to authenticate the U-Boot proper of
mx6ul_14x14_evk_defconfig target:
Authenticate image from DDR location 0x877fffc0...
bad magic magic=0x0 length=0x00 version=0x3
bad length magic=0x0 length=0x00 version=0x3
bad version magic=0x0 length=0x00 version=0x3
spl: ERROR: image authentication fail
Commit 0633e134784a ("imx: hab: Increase CSF_SIZE for i.MX6 and
i.MX7 devices") has increased CSF_SIZE to avoid a possible issue
when booting encrypted boot images.
Commit d21bd69b6e95 ("tools: mkimage: add firmware-ivt image type
for HAB verification") is hardcoding the CSF and IVT sizes, the
new CSF size is not being considered and u-boot-ivt.img fails to
boot.
Avoid hardcoded CSF and IVT size to fix this issue.
Signed-off-by: Breno Lima <breno.lima@nxp.com> Reviewed-by: Fabio Estevam <festevam@gmail.com>
Peng Fan [Mon, 26 Aug 2019 08:12:16 +0000 (08:12 +0000)]
imx: scu_api: add sc_pm_is_partition_started
Add sc_pm_is_partition_started to check whether a partition
has been started. This will be used to detect M4 partition booted up or
not, then we could choose which dtb to use. If M4 is up, we need
use dtb, such as imx8qm-mek-rpmsg.dtb.
Peng Fan [Mon, 26 Aug 2019 08:12:13 +0000 (08:12 +0000)]
imx8: fdt: add optee node
Add OP-TEE device tree node for Linux according to args passed from ATF.
If ATF has been built with OP-TEE running, boot_pointer[1] will indicate
that.
Peng Fan [Mon, 26 Aug 2019 08:11:56 +0000 (08:11 +0000)]
imx8: disable node when the resource is not owned
When resource is not assigned to non-secure Linux, if linux continue
to use the node, linux may crash or hang. So need to set the node
status to disabled for not owned resources.
The resource id is in the power-domains property in device tree,
so parse the power-domains property to get the resource id and
use scfw api to check whether it is owned by current partition.
Peng Fan [Thu, 22 Aug 2019 07:42:41 +0000 (07:42 +0000)]
imx: add container target
To support SPL loading container file, add a new Makefile target,
and introduce a new Kconfig file to source the cfg file which
will be parsed by mkimage.
Peng Fan [Thu, 22 Aug 2019 07:42:38 +0000 (07:42 +0000)]
spl: mmc: support loading i.MX container format file
i.MX8 only support AHAB secure boot with Container format image,
we could not use FIT to support secure boot, so introduce container
support to let SPL could load container images.
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com> Cc: Tien Fong Chee <tien.fong.chee@intel.com> Cc: York Sun <york.sun@nxp.com> Cc: Marek Vasut <marex@denx.de> Cc: Alex Kiernan <alex.kiernan@gmail.com> Cc: Simon Glass <sjg@chromium.org> Cc: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Cc: Kever Yang <kever.yang@rock-chips.com> Cc: Heiko Schocher <hs@denx.de> Signed-off-by: Peng Fan <peng.fan@nxp.com>
The first stage of flash.bin is larger than 584 * 512, so when
writting u-boot.itb, some data will be override. Enlarge the
CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR to fix boot.
Peng Fan [Wed, 14 Aug 2019 09:27:06 +0000 (09:27 +0000)]
imx: imx6qdl: dtsi: move U-Boot specific change to u-boot.dtsi
The changes were added by following patch:
commit <9002e735e717> ("imx: mx6sabresd: fix boot hang with video")
commit <f45ec8fcfb86> ("imx6: dts: add 'u-boot, dm-pre-reloc' to soc and ipu nodes")
Let's move the U-Boot specific change to imx6qdl-u-boot.dtsi
projects / u-boot.git / log