For configurations with gmii2rgmii and external phy the DT nodes link
should be gem->gmii2rgmii->phy. But due to limitation in Linux driver
the DT is mentioned as gem->phy and gmii2rgmii->phy as shown in below DT.
Since same DT is used in Linux and U-Boot we need to workaround this
issue by using the gmii2rgmii node which points to phy and we should
ignore the gem pointing to phy directly.
Do this workaround by updating priv->phydev->node value with
priv->phy_of_node only if it is not valid node.
The main reason is that QEMU is using BOOTP protocol which is sending DHCP
Offer to a broadcast address that's why it can't be disabled.
DHCP protocol has no issue because it returns directly to client MAC
address.
Both of these options are described in RFC951
(https://datatracker.ietf.org/doc/html/rfc951#section-4)
Michal Simek [Thu, 6 Jan 2022 08:49:41 +0000 (09:49 +0100)]
phy: zynqmp: Add serdes/psgtr driver
Add PSGTR driver for Xilinx ZynqMP.
The most of configurations are taken from Linux kernel psgtr driver.
USB3.0 and SGMII configurations are tested on SOM. In SGMII case also
IOU_SLCR reg is updated to get proper clock setup and signal detection
configuration.
Michal Simek [Tue, 11 Jan 2022 09:28:09 +0000 (10:28 +0100)]
net: uclass: Save generated ethernet MAC addresses to the environment
When a MAC address is randomly generated we currently only update the
appropriate data structure. For consistency and to re-align with
historic usage, it should be also saved to the appropriate environment
variable as well.
Michal Simek [Mon, 6 Dec 2021 15:25:20 +0000 (16:25 +0100)]
net: zynq: Add support for GEM reset
Perform reset before core initialization.
Standard flow which close to 99% users are using getting all IPs out of
reset that there is no need to reset IP again. This is because of all low
level initialization is done in previous bootloader stage.
In SOM case these IPs are not touched by previous bootloader stage that's
why reset needs to be called before IP is accessed to make sure that it is
in correct state.
Michal Simek [Mon, 6 Dec 2021 13:53:17 +0000 (14:53 +0100)]
net: zynq: Add support for mdio bus address decoding
Xilinx DTS files are using two way how to describe ethernet phy.
The first (already supported) has phy as subnode of gem node.
eth {
phy-handle = <&phy0>;
phy0: ethernet-phy@21 {
...
};
};
The second has mdio subnode (with mdio name) which has phy subnode. This
structure allow hadling MDIO reset signal (based on Linux mdio.yaml)
eth {
phy-handle = <&phy0>;
mdio {
phy0: ethernet-phy@21 {
...
};
};
};
This patch adds support for the second case where mdio subnode
is found driver will look at its parent to find out which gem is handling
MDIO bus.
T Karthik Reddy [Wed, 24 Nov 2021 11:16:55 +0000 (12:16 +0100)]
versal: Return ENVL_NOWHERE instead of ENVL_UNKNOWN
The system fails to boot without any environment location, so return
ENVL_NOWHERE when there's nowhere to store the environment instead
of ENVL_UNKNOWN.
The same change was also done by commit 50918d0df5cb ("xilinx: Return
ENVL_NOWHERE instead of ENVL_UNKNOWN") for zynq and zynqmp.
Ovidiu Panait [Thu, 2 Dec 2021 19:56:56 +0000 (21:56 +0200)]
xilinx: Kconfig: add XILINX_OF_BOARD_DTB_ADDR default value for microblaze
The xilinx board_fdt_blob_setup() implementation makes use of
XILINX_OF_BOARD_DTB_ADDR, but no default value is currently defined for
microblaze. Add one so that microblaze could also work with
CONFIG_OF_SEPARATE.
Ovidiu Panait [Tue, 30 Nov 2021 16:33:57 +0000 (18:33 +0200)]
microblaze: branch to base vector address on reset
Current code assumes that the vector base address is always at 0x0.
However, this value is configurable for MicroBlaze using the
CONFIG_XILINX_MICROBLAZE0_VECTOR_BASE_ADDR Kconfig option. Update the
reset routines to branch to this location instead.
Ovidiu Panait [Tue, 30 Nov 2021 16:33:56 +0000 (18:33 +0200)]
microblaze: start.S: add support for configurable vector base address
Current code assumes that the vector base address is always at 0x0.
However, this value is configurable for MicroBlaze, so update the
__setup_exceptions routine to work with any vector base address.
The r4 register is reserved for the vector base address inside
__setup_exceptions and the function prologe/epilogue are also updated to
save and restore r4.
Ovidiu Panait [Tue, 30 Nov 2021 16:33:55 +0000 (18:33 +0200)]
microblaze: add Kconfig symbol for the vector base address
MicroBlaze vector base address is configurable (hdl C_BASE_VECTORS
configuration parameter). Current code assumes that the reset vector
location is always 0x0.
Add the XILINX_MICROBLAZE0_VECTOR_BASE_ADDR Kconfig option so the user
can adjust the reset vector address.
Ovidiu Panait [Tue, 30 Nov 2021 16:33:54 +0000 (18:33 +0200)]
microblaze: migrate CONFIG_SYS_USR_EXCEP to Kconfig
Migrate CONFIG_SYS_USR_EXCEP to Kconfig. Also, rename it to
XILINX_MICROBLAZE0_USR_EXCEP in order to match the naming convention of
microblaze-generic Kconfig options.
Ovidiu Panait [Tue, 30 Nov 2021 16:33:53 +0000 (18:33 +0200)]
microblaze: drop CONFIG_SYS_RESET_ADDRESS macro
Microblaze is one the last two users of the CONFIG_SYS_RESET_ADDRESS
macro (the other is arch/powerpc/cpu/mpc8xx/cpu.c, but the macro is not
defined anywhere in powerpc code, so it should be removed there too).
Replace CONFIG_SYS_RESET_ADDRESS usage in start.S with
CONFIG_SYS_TEXT_BASE. If the reset address should really be
user-configurable, a new Kconfig option could be added.
Ovidiu Panait [Tue, 30 Nov 2021 16:33:51 +0000 (18:33 +0200)]
microblaze: Kconfig: SPL dependencies fixup
Enable SPL_LIBCOMMON_SUPPORT and SPL_LIBGENERIC_SUPPORT if CONFIG_SPL=y, in
order to fix the following link failures:
common/spl/spl.o: in function `board_init_r':
common/spl/spl.c:755: undefined reference to `puts'
...
common/spl/spl.o: in function `board_init_r':
common/spl/spl.c:756: undefined reference to `hang'
common/spl/spl.c:740: undefined reference to `memset'
Microblaze has three boot modes defined in microblaze/include/asm/spl.h,
but only booting from NOR flash is currently useable. Add a custom
board_boot_order() implementation so that RAM and SPI boot modes can also
be selected if the corresponding load-image support is present.
Ovidiu Panait [Tue, 30 Nov 2021 16:33:49 +0000 (18:33 +0200)]
microblaze: u-boot.lds: replace __end symbol with _end
board_fdt_blob_setup() uses the _end symbol to find the dtb in the non-spl
case. In order to allow microblaze builds to compile successfully with
CONFIG_OF_SEPARATE, the _end symbol must be defined. Align microblaze with
the other architectures and use _end symbol rather than __end to mark the
end of the u-boot binary.
Michal Simek [Thu, 18 Nov 2021 12:00:02 +0000 (13:00 +0100)]
xilinx: firmware: Move dcache handling directly to pmufw load config
Core function should make sure that data is stored properly that's why move
cache operations directly to zynqmp_pmufw_load_config_object() to be able
to call it from other functions.
Michal Simek [Thu, 18 Nov 2021 11:58:15 +0000 (12:58 +0100)]
arm64: zynqmp: Switch SOM to shared psu configuration
Previous psu init was targeting SOM + KV260 carrier card and also contain
configurations for other devices on carrier card. This config is removing
all expected configurations for CC and let U-Boot to handle all of it self.
This configuration is designed for SOM itself (and I would bet without
eMMC).
Michal Simek [Thu, 18 Nov 2021 12:42:28 +0000 (13:42 +0100)]
arm64: zynqmp: Remove clock-names from GEM in zynqmp-clk-ccf.dtsi
Remove clock-names from GEM nodes from clk-ccf because they should be only
present in zynqmp.dtsi. And as is visible both clock-names defined didn't
really match.
Michal Simek [Thu, 18 Nov 2021 12:40:31 +0000 (13:40 +0100)]
arm64: zynqmp: Add u-boot,dm-pre-reloc to dpsub node
u-boot,dm-pre-reloc is necessary for DP driver to allocate enough space for
framebuffer before relocation.
Power domain driver is called when video console is used for example by
loading BMP image.
T Karthik Reddy [Fri, 29 Oct 2021 11:11:43 +0000 (13:11 +0200)]
zynqmp: gpio: Add support for zynqmp gpio modepin driver
ZynqMP modepin driver has capability to get/set/check status of modepin
gpios. These modepins are accessed using xilinx firmware. In modepin
register, [3:0] bits set direction, [7:4] bits read IO, [11:8] bits
set/clear IO.
Vincent Stehlé [Wed, 24 Nov 2021 14:54:20 +0000 (15:54 +0100)]
qemu: common: Fix build with update capsule
The common emulation Makefile has a dependency on a non-existent
qemu_capsule.o when building with support for capsule update enabled
(CONFIG_EFI_RUNTIME_UPDATE_CAPSULE=y).
The code which was in qemu_capsule.c has been completely moved to
lib/efi_loader/efi_capsule.c by commit 7a6fb28c8e4b ("efi_loader: capsule:
add back efi_get_public_key_data()").
Remove the false dependency.
This fixes the following build error:
make[1]: *** No rule to make target 'board/emulation/common/qemu_capsule.o', needed by 'board/emulation/common/built-in.o'. Stop.
Fixes: commit 47a25e81d35c ("Revert "efi_capsule: Move signature from DTB to .rodata"") Signed-off-by: Vincent Stehlé <vincent.stehle@arm.com> Cc: Simon Glass <sjg@chromium.org>
Tom Rini [Fri, 26 Nov 2021 22:10:53 +0000 (17:10 -0500)]
Merge tag 'efi-2022-01-rc3-2' of https://source.denx.de/u-boot/custodians/u-boot-efi
Pull request for efi-2022-01-rc3-2
Test:
* fix pylint warnings
UEFI:
* disable interrupts before removing devices in ExitBootServices()
* implement poweroff in efi_system_reset() on sandbox
* allow booting via EFI even if some block device fails
Here efi_resister_disk() failed due to an error in the BTRFS implementation.
Move the logic to clear EFI_OS_INDICATIONS_FILE_CAPSULE_DELIVERY_SUPPORTED
to the rest of the capsule code.
If CONFIG_EFI_IGNORE_OSINDICATIONS=y, we should still clear the flag.
If OsIndications does not exist, we should not create it as it is owned by
the operating system.
Our algorithm for creating USB device paths may lead to duplicate device
paths which result in efi_disk_register() failing. Instead we should just
skip devices that cannot be registered as EFI block devices.
Fix a memory leak in efi_disk_add_dev() caused by the duplicate device
path.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Tom Rini [Fri, 19 Nov 2021 21:33:04 +0000 (16:33 -0500)]
efi: Call bootm_disable_interrupts earlier in efi_exit_boot_services
If we look at the path that bootm/booti take when preparing to boot the
OS, we see that as part of (or prior to calling do_bootm_states,
explicitly) the process, bootm_disable_interrupts() is called prior to
announce_and_cleanup() which is where udc_disconnect() /
board_quiesce_devices() / dm_remove_devices_flags() are called from. In
the EFI path, these are called afterwards. In efi_exit_boot_services()
however we have been calling bootm_disable_interrupts() after the above
functions, as part of ensuring that we disable interrupts as required
by the spec. However, bootm_disable_interrupts() is also where we go
and call usb_stop(). While this has been fine before, on the TI J721E
platform this leads us to an exception. This exception seems likely to
be the case that we're trying to stop devices that we have already
disabled clocks for. The most direct way to handle this particular
problem is to make EFI behave like the do_bootm_states() process and
ensure we call bootm_disable_interrupts() prior to ending up in
usb_stop().
Cc: Ilias Apalodimas <ilias.apalodimas@linaro.org> Cc: Heinrich Schuchardt <xypron.glpk@gmx.de> Cc: Simon Glass <sjg@chromium.org> Suggested-by: Ilias Apalodimas <ilias.apalodimas@linaro.org> Signed-off-by: Tom Rini <trini@konsulko.com> Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Tom Rini [Sat, 20 Nov 2021 14:36:37 +0000 (09:36 -0500)]
Merge branch 'efi-2022-01' of https://source.denx.de/u-boot/custodians/u-boot-efi
Scripts:
* Update spelling.txt
LMB:
* remove extern keyword in lmb.h
* drop unused lmb_size_bytes()
Test:
* test truncation in snprintf()
Documentation:
* add include/lmb.h to HTML documentation
UEFI:
* reduce non-debug logging output for measured boot
* fix use after free in measured boot
* startup the tpm device when installing the protocol
* implement EFI_EVENT_GROUP_BEFORE_EXIT_BOOT_SERVICES
* record capsule result only if capsule is read
Ilias Apalodimas [Thu, 18 Nov 2021 08:13:42 +0000 (10:13 +0200)]
efi_loader: startup the tpm device when installing the protocol
Due to U-Boot's lazy binding mentality the TPM is probed but not properly
initialized. The user can startup the device from the command line
e.g 'tpm2 startup TPM2_SU_CLEAR'. However we can initialize the TPM during
the TCG protocol installation, which is easier to use overall.
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org> Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Ilias Apalodimas [Thu, 18 Nov 2021 07:03:39 +0000 (09:03 +0200)]
efi_loader: fix FinalEvents table if an EFI app invoked GetEventLog
As described in the TCG spec [1] in sections 7.1.1 and 7.1.2 the FinalEvent
table should include events after GetEventLog has been called. This
currently works for us as long as the kernel is the only EFI application
calling that. Specifically we only implement what's described in 7.1.1.
So refactor the code a bit and support EFI application(s) calling
GetEventLog. Events will now be logged in both the EventLog and FinalEvent
table as long as ExitBootServices haven't been invoked.
Masami Hiramatsu [Fri, 12 Nov 2021 13:05:15 +0000 (22:05 +0900)]
efi_loader: capsule: Record capsule result only if capsule is read
Record capsule update result only if the capsule file is
successfully read, because the capsule GUID is not sure when
the file can not be read or the file is not a capsule.
Without this fix, if user puts a dummy (non-capsule) file
under (ESP)EFI/UpdateCapsule, U-Boot causes a synchronous
abort.
This also fixes use-after-free bug of the 'capsule' variable.
Masahisa Kojima [Tue, 9 Nov 2021 11:35:53 +0000 (20:35 +0900)]
efi_loader: Reduce efi_tcg2 logging statement
log_info() is used for the debug level logging statement
which should use log_debug() instead. Convert it to reduce the
log output.
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org> Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Masahisa Kojima [Fri, 12 Nov 2021 07:24:27 +0000 (16:24 +0900)]
efi: add comment for efi_system_table and efi_configuration_table
This commit adds the comment for efi_system_table and
efi_configuration_table structure.
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Tom Rini [Thu, 18 Nov 2021 23:25:19 +0000 (18:25 -0500)]
Merge branch '2021-11-18-regression-fixes'
- An assortment of fixes related to GD, GD_FLG_SKIP_RELOC, and the lmb
- Environment fix on synquacer developmentbox
- Fix for get_info is not valid in partition code
Marek Vasut [Sat, 13 Nov 2021 17:34:37 +0000 (18:34 +0100)]
lmb: Reserve U-Boot separately if relocation is disabled
In case U-Boot starts with GD_FLG_SKIP_RELOC, the U-Boot code is
not relocated, however the stack and heap is at the end of DRAM
after relocation. Reserve a LMB area for the non-relocated U-Boot
code so it won't be overwritten.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Simon Glass <sjg@chromium.org> Cc: Tom Rini <trini@konsulko.com>
Marek Vasut [Sat, 13 Nov 2021 17:34:04 +0000 (18:34 +0100)]
board_f: Copy GD to new GD even if relocation disabled
Even if U-Boot has relocation disabled via GD_FLG_SKIP_RELOC , the
relocated stage of U-Boot still picks GD from new_gd location. The
U-Boot itself is not relocated, but GD might be, so copy the GD to
new GD location even if relocation is disabled.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Peng Fan <peng.fan@oss.nxp.com> Cc: Simon Glass <sjg@chromium.org> Cc: Tom Rini <trini@konsulko.com>
Masami Hiramatsu [Thu, 18 Nov 2021 05:45:25 +0000 (14:45 +0900)]
Revert "board: synquacer: developerbox: Don't set gd->env_addr to default_environment"
Without default setting of gd->env_addr, U-Boot will cause
a synchronous abort if the env-variables on the SPI flash is
broken or not saved corectly. Set gd->env_addr correctly.
Without get_desc, the tpm command will not provide a
description of the device in 'tpm device' or 'tpm info'.
Due to the characteristics of the Atmel TPM it isn't
possible to determine certain attributes (e.g open/close
status) without using the TPM stack (compare Infineon
and ST TPM drivers), so just print out the chip model
and udevice name as the identifier.
Mathew McBride [Thu, 11 Nov 2021 04:06:27 +0000 (04:06 +0000)]
cmd: tpm-v1: fix load_key_by_sha1 compile errors
This command is not compiled by default and has not been updated alongside
changes to the tpmv1 API, such as passing the TPM udevice to the relevant
functions.
Tom Rini [Tue, 16 Nov 2021 14:51:04 +0000 (09:51 -0500)]
Merge tag 'xilinx-for-v2022.01-rc3' of https://source.denx.de/u-boot/custodians/u-boot-microblaze
Xilinx changes for v2022.01-rc3
sdhci:
- Fix emmc mini case with missing firmware interface
zynqmp:
- Restore JTAG interface if required
- Allow overriding board name
- Add support for DLC21
- Fix one fallthrought statement description
- Use config macro instead of name duplication
- Save multiboot to variable
firmware:
- Handle ipi_req errors better
- Use local buffer in case user doesn't need it instead of NULL/0 location
Andy Shevchenko [Mon, 8 Nov 2021 18:03:38 +0000 (21:03 +0300)]
image: Explicitly declare do_bdinfo()
Compiler is not happy:
common/image-board.c: In function ‘boot_get_kbd’:
common/image-board.c:902:17: warning: implicit declaration of function ‘do_bdinfo’ [-Wimplicit-function-declaration]
902 | do_bdinfo(NULL, 0, 0, NULL);
| ^~~~~~~~~
Move the forward declaration to a header.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Masami Hiramatsu [Wed, 10 Nov 2021 00:40:07 +0000 (09:40 +0900)]
configs: synquacer: Fix dfu_alt_info to use nor1
Fix dfu_alt_info to use nor1 instead of the device name.
This reverts a part of commit 59bd18d4c4d7 ("configs: synquacer:
Remove mtdparts settings and update DFU setting") because the
commit a4f2d8341455 ("mtd: spi: nor: force mtd name to "nor%d"")
changed the mtd device naming scheme to nor%d.
The subdivision name "TQ Components" hasn't been in use for a long time.
Rename the vendor directory to "tq", which also matches our Device Tree
vendor prefix.
Alistair Delva [Wed, 20 Oct 2021 21:31:32 +0000 (21:31 +0000)]
arm64: relocate-rela: Add support for ld.lld
Cap end of relocations by the binary size.
Linkers like to insert some auxiliary sections between .rela.dyn and
.bss_start. These sections don't make their way to the final binary, but
reloc_rela still tries to relocate them, resulting in attempted read
past the end of file.
When linking U-Boot with ld.lld, the STATIC_RELA feature (enabled by
default on arm64) breaks the build. After this patch, U-Boot can be
linked successfully with and without CONFIG_STATIC_RELA.
Originally-from: Elena Petrova <lenaptr@google.com> Signed-off-by: Alistair Delva <adelva@google.com> Cc: David Brazdil <dbrazdil@google.com> Cc: Scott Wood <scottwood@freescale.com> Cc: Tom Rini <trini@konsulko.com>
projects / u-boot.git / log