sh: Remove CONFIG_COMMANDS from MS7720SE config file

Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>

sh: Update SuperH SCIF driver

This patch fixed wrong SH7720 CPU macro and changed macro that
calculated value of SCBRR register.

Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>

pcmcia: Remove CONFIG_COMMANDS from marubun pcmcia driver

Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>

sh: Add support SH7710/SH7712

SH7710/SH7712 of SH3 CPU are supported.
SH771X is called SH-Ether, and has the Ether controller in CPU.
The driver of Ether is not included in this patch.

Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>

sh: Add support of map_physmem() and unmap_physmem() to SuperH

This patch add the support of map_physmem() and unmap_physmem()
used with Common Flash Interface(CFI) driver.

Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>

sh: Add maintainer of MS7720SE to the MAINTAINER file

Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>

sh: Fix board name in MS7720SE's config.mk

Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>

sh: Add MS7720SE to MAKEALL

Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>

sh: Add support for MS7720RP02 board

Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
CC: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Acked-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>

sh: Add support for SH7720 in serial_sh driver.

Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
CC: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Acked-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>

sh: Add support SH3 and SH7720

Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
CC: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Acked-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>

Merge branch 'master' of git://www.denx.de/git/u-boot-ppc4xx

QE: fix compile warning

qe.c: In function 'qe_upload_firmware':
qe.c:390: warning: pointer targets in passing argument 2
uec.c: In function 'uec_initialize':
uec.c:1236: warning: 'uec_info' may be used uninitialized

Signed-off-by: Dave Liu <daveliu@freescale.com>

ppc4xx: Update Kilauea CPLD configuration with USB PHY reset bit

Now that bit 29 is the USB PHY reset bit, update the Kilauea port
to remove the USB PHY reset after powerup. The CPLD will keep the
USB PHY in reset (active low) until the bit is set to 1 in
board_early_init_f().

Signed-off-by: Stefan Roese <sr@denx.de>

ARM: update mach-types.h from 2.6.24-rc7 Linux kernel tree

Signed-off-by: Wolfgang Denk <wd@denx.de>

ADS5121: Fix typo in ads5121.c, adjust default environment

Signed-off-by: Wolfgang Denk <wd@denx.de>

ADS5121: MAX slew rate for PATA pins

Signed-off-by: John Rigby <jrigby@freescale.com>

Fix Makefile dependency problem with parallel builds.

Signed-off-by: Wolfgang Denk <wd@denx.de>

MPC8544DS: fix board Makefile for silent build (with -s)

Signed-off-by: Wolfgang Denk <wd@denx.de>

PMC440 board: fix board Makefile for out-of-tree building

Signed-off-by: Wolfgang Denk <wd@denx.de>

Makalu: fix compile warning

Signed-off-by: Wolfgang Denk <wd@denx.de>

Merge branch 'master' of git+ssh://10.10.0.7/home/wd/git/u-boot/master

cmd_nand : fix compiler warning.

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

CFI: Fix CONFIG_FLASH_CFI_LEGACY compilation

Signed-off-by: Michael Schwingen <michael@schwingen.org>
Acked-by: Stefan Roese <sr@denx.de>

Merge branch 'master' of /home/stefan/git/u-boot/u-boot

MPC8360ERDK: fix incorrect initialization of CFG_I2C_NOPROBES

Signed-off-by: Wolfgang Denk <wd@denx.de>

MPC8xx FEC driver: fix compiler warning.

Signed-off-by: Wolfgang Denk <wd@denx.de>

Fix Makefile dependencies issues; allow silent build

- get rid of "version" target whichdidn't really work
- make autoconf.mk depend on version_autogenerated.h to make sure
  to rebuild files as needed
- add XECHO macro to allow for silent build using "make -s"

Signed-off-by: Wolfgang Denk <wd@denx.de>

ADS5121e: fix compile warning

Signed-off-by: Wolfgang Denk <wd@denx.de>

MUNICes: fix board Makefile for remote build directory

Signed-off-by: Wolfgang Denk <wd@denx.de>

MPC5200: don't use hardcoded MBAR address in Bestcomm firmware

Signed-off-by: Oliver Weber <almoeli@gmx.de>

Make bootretry work when command line editing is enabled

Currently, when CONFIG_CMDLINE_EDITING is set, bootretry doesn't work.
This patch fixes the problem.

Signed-off-by: Andreas Engel <andreas.engel@ericsson.com>

Refactor code for "i2c sdram" command

Signed-off-by: Larry Johnson <lrj@acm.org>

Fix "i2c sdram" command for DDR2 DIMMs

Many of the SPD bytes for DDR2 SDRAM are not interpreted correctly by the
"i2c sdram" command.  This patch provides correct alternative
interpretations when DDR2 memory is detected.

Signed-off-by: Larry Johnson <lrj@acm.org>

Fix linker scripts: add NOLOAD atribute to .bss/.sbss sections

With recent toolchain versions, some boards would not build because
or errors like this one (here for ocotea board when building with
ELDK 4.2 beta):
ppc_4xx-ld: section .bootpg [fffff000 -> fffff23b] overlaps section .bss [fffee900 -> fffff8ab]

For many boards, the .bss section is big enough that it wraps around
at the end of the address space (0xFFFFFFFF), so the problem will not
be visible unless you use a 64 bit tool chain for development. On
some boards however, changes to the code size (due to different
optimizations) we bail out with section overlaps like above.

The fix is to add the NOLOAD attribute to the .bss and .sbss
sections, telling the linker that .bss does not consume any space in
the image.

Signed-off-by: Wolfgang Denk <wd@denx.de>

USB: Add Philips 1561 PCI-OHCI ids
(needed for M5475EVB)

Signed-off-by: TsiChungLiew <Tsi-Chung.Liew@freescale.com>

Add MAINTAINERS entries for ids8247, jupiter, municse, sc3 and uc101
boards.

Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Wolfgang Denk <wd@denx.de>

MPC512X: Cleanup bus clock names.

Signed-off-by: Grzegorz Bernacki <gjb@semihalf.com>

MPC512X: Fixed typo in macro name.

Signed-off-by: Grzegorz Bernacki <gjb@semihalf.com>

ads5121: Added support for FDT.

Signed-off-by: Grzegorz Bernacki <gjb@semihalf.com>

Coding Style cleanup; update CHANGELOG.

Signed-off-by: Wolfgang Denk <wd@denx.de>

Fixed syntax error in function init_e300_core() of mpc83xx/start.S if

Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Heiko Schocher <hs@denx.de>

MUNICes: Set the right CFG_DEFAULT_MBAR value.

Signed-off-by: Heiko Schocher <hs@denx.de>

added the config File for the MUNICes board.

Signed-off-by: Heiko Schocher <hs@denx.de>

added basic support for the MUNICes board.

Signed-off-by: Heiko Schocher <hs@denx.de>

Update CHANGELOG and MAINTAINERS files.

Signed-off-by: Wolfgang Denk <wd@denx.de>

Fix compilation problem in common/cmd_bmp.c

common/cmd_bmp.c fails to compile if CONFIG_VIDEO_BMP_GZIP
isn't defined. This patch fix this.

Signed-off-by: Anatolij Gustschin <agust@denx.de>

Fix defaultconfig for the mgcoge board.

Signed-off-by: Heiko Schocher <hs@denx.de>

Added support for the mgcoge board from keymile.

Signed-off-by: Heiko Schocher <hs@denx.de>

Enable SMC microcode relocation patch for SMC1.

Signed-off-by: Heiko Schocher <hs@denx.de>

Added support for the mgsuvd board from keymile.

Signed-off-by: Heiko Schocher <hs@denx.de>

Fix 64-bit vsprintf.

There were some size and unsigned problems.
Also add support for "ll" size modifier in format string like glibc

Signed-off-by: James Yang <James.Yang@freescale.com>
Acked-by: Jon Loeliger <jdl@freescale.com>

Remove superfluous preprocessor conditionals from LM73 driver

(1) Remove unused symbol "CFG_EEPROM_PAGE_WRITE_ENABLE".

(2) Use conditional Makefile.o.

Signed-off-by: Larry Johnson <lrj@acm.org>

Add support for the TK885D baseboard from TELE-DATA

The TK885D board uses a TQM885D module from TQ, this port adds an
own configuration file and adds a last_stage_init() method to
configure the two PHYs, depending on the phy_auto_nego environment
variable.

Signed-off-by: Guennadi Liakhovetski <lg@denx.de>

Merge branch 'master' of git://www.denx.de/git/u-boot-video

Merge branch 'master' of git://www.denx.de/git/u-boot-ppc4xx

Merge branch 'master' of git://www.denx.de/git/u-boot-mpc83xx

Merge branch 'master' of git://www.denx.de/git/u-boot-mpc86xx

Merge ../custodians

Fix compiler warning

main.c: In function 'readline_into_buffer':
main.c:927: warning: unused variable 'p_buf'

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

Add Fujitsu CoralP/Lime video driver

Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Rodolfo Giometti <giometti@linux.it>

Fix video console newline and carriage return handling

Lines of the lenght CONSOLE_COLS or greater than CONSOLE_COLS
are not displayed correctly. This is an attempt to fix
this issue. Also add carriage return handling.

Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Rodolfo Giometti <giometti@linux.it>

ppc4xx: Fix sdram init on Sequoia boards

Clear possible errors in MCSR resulting from data-eye-search.
If not done, then we could get an interrupt later on when
exceptions are enabled.

Signed-off-by: Stefan Roese <sr@denx.de>

ppc4xx: Rework Lime support for lwmon5

Rework Lime support for lwmon5 using new video driver

Signed-off-by: Anatolij Gustschin <agust@denx.de>

ppc4xx: Update PMC440 config file

Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>

ppx4xx: Fix sdram init on PMC440 boards

Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>

mpc83xx: Fix the bug of 266MHz data rate DDR

The DDR doesn't work on the 266MHz data rate,
the patch fix the bug.

Signed-off-by: Dave Liu <daveliu@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>

mpc83xx: Make the code more readable

Format the code, make it more readable

Signed-off-by: Dave Liu <daveliu@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>

mpc83xx: Reduce the latency of DDR

Reduce the AL from 2 to 1 clock to improve the performance.

Signed-off-by: Dave Liu <daveliu@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>

mpc83xx: Fix the wrong definition of MPC8315E

According to the latest user manual of MPC8315E,
1) The SVCOD of HRCWL is different than 837x
2) The SCCR has changes

Signed-off-by: Dave Liu <daveliu@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>

mpc83xx: Fix the typo in mpc83xx.h

The SPCR about TSEC priority is wrong.

Signed-off-by: Michael Barkowski <Michael.Barkowski@freescale.com>
Signed-off-by: Joe D'Abbraccio <Joe.D'abbraccio@freescale.com>
Signed-off-by: Dave Liu <daveliu@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>

mpc83xx: Fix the typo in global data struct

Fix the typo in global_data.h

Signed-off-by: Dave Liu <daveliu@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>

mpc83xx: Remove cache config from config.h

clean up the cache config from configs.h of board

Signed-off-by: Dave Liu <daveliu@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>

mpc83xx: add support for the MPC8360E-RDK

This is MPC8360E based board with:
- 256MB fixed SDRAM;
- 8MB Intel Strata NOR flash;
- StMICRO 64MiB NAND flash;
- two 10/100/1000 ethernet ports connected via Broadcom
  BCM5481 PHYs;
- two 10/100 ethernet ports connected via National
  DP83848 PHYs;
- one PCI and one miniPCI slots;
- four serial ports (two NS16550-compatible, two UCCs);
- four USB ports working through MPC8360E "FHCI" USB controller;
- Fujitsu MB86277 graphics controller;
- Analog to Digital Converter/Touchscreen controller, AD7843
  connected to SPI.

Features not supported in this patch are:
- StMICRO 64MiB NAND flash (patch sent);
- MINT framebuffer initialization (patch is pending);
- Fetching production information from the EEPROM via I2C;
- FHCI USB;
- Two slow UCCs used as RS-485 UARTs.

Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>

mpc83xx: add "fsl, qe" compatible fixups

New device trees will use "fsl,qe" compatible properties.

Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>

mpc83xx: add missing CONFIG_HAS_ETH0 defines

the new libfdt code only updates eth0 if CONFIG_HAS_ETH0
is defined; add the define to the missing board configs.

Thanks to Emilian Medve for finding this.

Signed-off-by: Kim Phillips <kim.phillips@freescale.com>

Merge commit 'wd/master'

86xx: Support 2GB DIMMs

Configure the number of bits used to address the banks inside the SDRAM
device.  The default register value of 0 means 2 bits to address 4 banks.
Higher capacity devices like a 2GB DIMM require 3 bits to address 8 banks.

Signed-off-by: Becky Bruce <bgill@freescale.com>

ppc4xx: Make Sequoia boot vxWorks

vxWorks expects in
TLB 0 a entry for the Machine Check interrupt
TLB 1 a entry for the RAM
TLB 2 a entry for the EBC
TLB 3 a entry for the boot flash

After changing the baudrate to 9600 I had no problems to boot the
vxWorks image as distributed by WindRiver (Revision 2.0/1 from
June 18, 2007)

Signed-off-by: Niklaus Giger <niklaus.giger@netstal.com>

ppc4xx: Fix dflush() to restore DVLIM register

Signed-off-by: Larry Johnson <lrj@acm.org>

Nios2: remove common/cmd_bdinfo.c unused variable.

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Scott McNutt <smcnutt@psyent.com>

Fix Ethernet init() return codes

Change return values of init() functions in all Ethernet drivers to conform
to the following:

    >=0: Success
    <0:  Failure

All drivers going forward should return 0 on success.  Current drivers that
return 1 on success were left as-is to minimize changes.

Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Acked-by: Stefan Roese <sr@denx.de>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
Acked-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Acked-By: Timur Tabi <timur@freescale.com>

Coding Style cleanup; update CHANGELOG

Signed-off-by: Wolfgang Denk <wd@denx.de>

Merge branch 'master' of git://www.denx.de/git/u-boot-mpc85xx

Add QE brg freq and correct qe bus freq fdt update code

Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>

Merge branch 'master' of git+ssh://10.10.0.7/home/wd/git/u-boot/master

Remove cache config from ATUM8548 and sbc8548 configs

These boards weren't updated by Kumar's config patch because they
weren't in the tree, yet.

Signed-off-by: Andy Fleming <afleming@freescale.com>

85xx: add ability to upload QE firmware

Define the layout of a binary blob that contains a QE firmware and instructions
on how to upload it.  Add function qe_upload_firmware() to parse the blob and
perform the actual upload.  Add command-line command "qe fw" to take a firmware
blob in memory and upload it.  Update ft_cpu_setup() on 85xx to create the
'firmware' device tree node if U-Boot has uploaded a firmware.  Fully define
'struct rsp' in immap_qe.h to include the actual RISC Special Registers.

Signed-off-by: Timur Tabi <timur@freescale.com>

85xx: Remove cache config from configs.h

Either use the standard defines in asm/cache.h or grab the information
at runtime from the L1CFG SPR.

Also, minor cleanup in cache.h to make the code a bit more readable.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

mpc85xx: Add support for ATUM8548 (updated)

Add support for Instituto Atlantico's ATUM8548 board

Signed-off-by: robert lazarski <robertlazarski@gmail.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>

mpc85xx: Add support for ATUM8548 (updated)

Add support for Instituto Atlantico's ATUM8548 board

Signed-off-by: robert lazarski <robertlazarski@gmail.com>

mpc85xx: Add support for SBC8548 (updated)

Add support for Wind River's SBC8548 reference board.

Signed-off by: Joe Hamman <joe.hamman@embeddedspecialties.com>

mpc85xx: Add support for SBC8548 (updated)

Add support for Wind River's SBC8548 reference board.

Signed-off by: Joe Hamman <joe.hamman@embeddedspecialties.com>
Signed-off by: Andy Fleming <afleming@freescale.com>

MPC8568E-MDS: set up QE pario for UART1

To use UART1 on the MPC8568E-MDS, QE pario pins PC[0:3] should
be set up appropriately.

Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>

MPC8568E-MDS: reset UCCs to use them reliably

In order to use GETH1 and GETH2 on the MPC8568E-MDS, we should reset
UCCs.

p.s Similar code exists in the Linux kernel board file (for capability
reasons with older U-Boots), but should be removed some day.

Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>

Reworked FSL Book-E TLB macros to be more readable

The old macros made it difficult to know what WIMGE and perm bits
were set for a TLB entry.  Actually use the bit masks for these items
since they are only a single bit.

Also moved the macros into mmu.h out of e500.h since they aren't specific
to e500.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

Use FSL Book-E MMU macros from Linux Kernel

Grab the FSL Book-E MAS register macros from Linux.  Also added
defines for page sizes up to 4TB and removed SHAREN since it doesnt
really exist.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

Fix my own merge stupidity

Way back in August I merged Heiko's patch:
566a494f592: [PCS440EP] upgrade the PCS440EP board

with Jon's CONFIG_COMMANDS patches.

This was done in commit: 6bf6f114dcdd97ec3f80c2761ed40e31229d6b78

However, in the process, I left out some of Heiko's good changes.

Now Heiko's and Jon's patches are properly merged in fat_register_device()

Signed-off-by: Andy Fleming <afleming@freescale.com>

Merge branch 'master' of /home/wd/git/u-boot/custodians

Merge branch 'master' of git://www.denx.de/git/u-boot-freebsd