Giulio Benetti [Fri, 10 Jan 2020 14:47:05 +0000 (15:47 +0100)]
serial_lpuart: add clock enable if CONFIG_CLK is defined
This driver assumes that lpuart clock is already enabled before probing
but using DM only lpuart won't be automatically enabled so add
clk_enable() when probing if CONFIG_CLK is defined. If clock is not
found, because DM is not used, let's emit a warning and proceed, because
serial clock could also be already enabled by non DM code. If clock is
found but cna't be enabled then return with error.
Giulio Benetti [Fri, 10 Jan 2020 14:46:58 +0000 (15:46 +0100)]
clk: imx: pllv3: add PLLV3_SYS support
Add PLLV3_SYS support by adding set/get_rate() for PLLV3_SYS but keeping
generic enable()/disable(). Add a different driver because ops are
different respect to GENERIC/USB.
Giulio Benetti [Fri, 10 Jan 2020 14:46:55 +0000 (15:46 +0100)]
clk: imx: pllv3: add enable() support
Before set_rate() pllv3 needs enable() to power the pll up.
Add enable() taking into account different power_bit and
different powerup_set, because some pll needs its power_bit to be
set or reset to be powered on.
Giulio Benetti [Fri, 10 Jan 2020 14:46:53 +0000 (15:46 +0100)]
clk: imx: pllv3: register PLLV3 GENERIC and USB as 2 different clocks
Better to register the 2 clock as 2 different drivers because they work
slightly differently depending on power_bit and powerup_set bits coming
on next patches.
Giulio Benetti [Fri, 10 Jan 2020 14:46:51 +0000 (15:46 +0100)]
spl: fix entry_point equal to load_addr
At the moment entry_point is set to image_get_load(header) that sets it
to "load address" instead of "entry point", assuming entry_point is
equal to load_addr, but it's not true. Then load_addr is set to
"entry_point - header_size", but this is wrong too since load_addr is
not an entry point.
So use image_get_ep() for entry_point assignment and image_get_load()
for load_addr assignment.
clk: imx8qxp: extend to support getting I2C IPG clock
Since commit d02be21d3004 ("i2c: imx_lpi2c: add ipg clk") getting
I2C clocks doesn't work. Add I2C IPG clock IDs to related switch
statements to fix it.
Fabio Estevam [Mon, 6 Jan 2020 23:11:28 +0000 (20:11 -0300)]
ARM: dts: imx6ul-14x14-evk: Pass the "broken-cd" property
imx6ul-14x14-evk does not have a GPIO dedicated for reading the card
detect pin on the eSDHC2 port. In such cases the "broken-cd" property
must be passed, otherwise the card cannot be detected.
Fabio Estevam [Mon, 6 Jan 2020 23:11:27 +0000 (20:11 -0300)]
mmc: fsl_esdhc_imx: Handle the "broken-cd" property
When no GPIO is used to read the card detect status the following
error is seen:
MMC: FSL_SDHC: 0, FSL_SDHC: 1
Loading Environment from MMC... MMC: no card present
*** Warning - No block device, using default environment
Fix it by handling the "broken-cd" property in the same way
that drivers/mmc/sdhci.c does, which considers that the SD card
is present when the "broken-cd" property is passed.
Fabio Estevam [Mon, 6 Jan 2020 15:31:55 +0000 (12:31 -0300)]
mx6ul_14x14_evk: Fix SPL boot hang
Currently the following SPL hang is observed:
U-Boot SPL 2020.01-rc5-00079-g797eee36a1 (Jan 06 2020 - 11:24:09 -0300)
Trying to boot from MMC1
Card did not respond to voltage select!
spl: mmc init failed with error: -95
SPL: failed to boot from all boot devices
### ERROR ### Please RESET the board ###
Fix it by moving the eSDHC2 initialization to SPL.
While at it, since this board uses DM_MMC all the esdhc board
code can be removed to make the code simpler.
Eugeniu Rosca [Tue, 24 Dec 2019 16:51:08 +0000 (17:51 +0100)]
cmd: adtimg: Refactor usage style
Trying to extend 'adtimg' functionality [1], we've been severely hit
by a major limitation in the command's usage scheme. Specifically, the
command's user interface appears to be too centric to getting the
DTB/DTBO entry [3] based on the index of the desired DT in the image,
which makes it really difficult retrieving the DT entry based on
alternative criteria (e.g. filtering by id/rev fields), the
latter being demanded by real life customer use-cases [1].
This went to the point of receiving below feedback from Sam [2]:
-- snip --
As for 'dtimg' command: after giving it some thought, I think not much
people using it yet. So in this particular case I don't have some
strong preference, and if you think the 'dtimg' interface is ugly, and
it overcomes "don't break interfaces" rule, maybe now is a good time
to rework it (before it gets widely used).
-- snip --
Given the above, rework the usage pattern from [4] to [5], in order to
allow an intuitive enablement of "by id|rev" DT search [6].
[1] https://patchwork.ozlabs.org/cover/1202575/
("cmd: dtimg: Enhance with --id and --rev options (take #1)")
[2] https://patchwork.ozlabs.org/patch/1182207/#2317020
[3] https://source.android.com/devices/architecture/dto/partitions
[4] Old usage
adtimg dump <addr> - Print image contents
adtimg start <addr> <index> <varname> - Get DT address by index
adtimg size <addr> <index> <varname> - Get DT size by index
[5] New usage
adtimg addr <addr> - Set image location to <addr>
adtimg dump - Print out image contents
adtimg get dt --index=<i> [avar [svar]] - Get DT address and size by index
[6] Soon-to-be-provided "by id|rev" add-on functionality
adtimg get dt --id=<id> --rev=<rev> [avar [svar [ivar]]]
- Get DT address/size/index by id|rev fields
Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com> Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org>
Eugeniu Rosca [Tue, 24 Dec 2019 16:51:06 +0000 (17:51 +0100)]
dtimg/am57xx_evm_defconfig: Rename dtimg to adtimg
Rename the existing 'dtimg' command to 'adtimg', in order to:
- Suggest the Android origins and scope
- Be consistent with the upcoming 'abootimg' command (naming
suggested by Simon [*])
The change in _not_ backward compatible, but its benefits outweigh its
downsides, given that we don't expect active users of 'dtimg' today.
Perform the rename in several steps:
1. Rename *.c file and Kconfig symbol. This should allow
'git log --follow' to properly track the history of 'adtimg.c'
2. 's/dtimg/adtimg/g' in the internal namespace of 'adtimg.c'
ELF comparison [**] before and after shows no functional change.
Cc: Tom Rini <trini@konsulko.com> Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com> Reviewed-by: Simon Glass<sjg@chromium.org> Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org>
Rajesh Ravi [Fri, 22 Nov 2019 22:50:01 +0000 (14:50 -0800)]
arm: cpu: armv8: add support for arm psci reset2.
Current U-Boot has only support for psci reset.
Adding support for arm psci reset2 allows passing of reset level
and other platform sepcific parameters like strap settings
to lowlevel psci implementation.
Signed-off-by: Rajesh Ravi <rajesh.ravi@broadcom.com> Signed-off-by: Vladimir Olovyannikov <vladimir.olovyannikov@broadcom.com>
Programs the following:
1. Redistributor PROCBASER configuration table (which
is common for all redistributors)
2. Redistributor pending table (PENDBASER), for all the
available redistributors.
Signed-off-by: Bharat Kumar Reddy Gooty <bharat.gooty@broadcom.com> Signed-off-by: Vladimir Olovyannikov <vladimir.olovyannikov@broadcom.com>
Philippe Reynes [Thu, 9 Jan 2020 16:34:02 +0000 (17:34 +0100)]
test/cmd_ut.c: fix cmd_ut_category
In the function cmd_ut_category, the prefix is used with
the function strncmp to know if the prefix should be
removed from the test name, even if the prefix is NULL.
To avoid this issue, we consider that a prefix NULL
mean no prefix. So we only try to remove the prefix
from the test_name if the prefix is not NULL, then
we avoid to call the function strncmp with a NULL
prefix.
Reported-by: Coverity CID 281110 Fixes: 4ad4edfe ("cmd_ut: add a parameter prefix to the function cmd_ut_category") Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
Andy Shevchenko [Fri, 29 Nov 2019 17:47:59 +0000 (19:47 +0200)]
gcc-9: silence 'address-of-packed-member' warning
GCC 9.x starts complaining about potential misalignment of the pointer to
the array (in this case alignment=2) in the packed (alignment=1) structures.
Repeating Linus' Torvalds commit 6f303d60534c in the Linux kernel.
Original commit message:
We already did this for clang, but now gcc has that warning too.
Yes, yes, the address may be unaligned. And that's kind of the point.
This in particular hides the warnings like
drivers/usb/gadget/composite.c:545:23: warning: taking address of packed member of ‘struct usb_string_descriptor’ may result in an unaligned pointer value [-Waddress-of-packed-member]
545 | collect_langs(sp, s->wData);
drivers/usb/gadget/composite.c:550:24: warning: taking address of packed member of ‘struct usb_string_descriptor’ may result in an unaligned pointer value [-Waddress-of-packed-member]
550 | collect_langs(sp, s->wData);
drivers/usb/gadget/composite.c:555:25: warning: taking address of packed member of ‘struct usb_string_descriptor’ may result in an unaligned pointer value [-Waddress-of-packed-member]
555 | collect_langs(sp, s->wData);
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Holger Brunck [Mon, 25 Nov 2019 16:24:14 +0000 (17:24 +0100)]
km/boards: add MAC address offset as argument to ivm_populate_env
For upcoming SECU board we have different MAC address offsets depending
on which functional unit we are running. In this case we need to pass
this value to the ivm_populate_env function instead of using the hard
coded config option there.
Signed-off-by: Holger Brunck <holger.brunck@ch.abb.com> CC: Stefan Roese <sr@denx.de> CC: Valentin Longchamp <valentin.longchamp@ch.abb.com> CC: Marek Vasut <marex@denx.de> Reviewed-by: Stefan Roese <sr@denx.de>
Han Nandor [Tue, 12 Nov 2019 08:39:38 +0000 (08:39 +0000)]
rtc: add support for DS3232 device
DS3232 is an i2c RTC with 236 bytes of battery-backed SRAM.
Add an RTC driver for DS3232 device, which provides time and
date support. Also read and write functions are provided,
which can be used to access the SRAM memory.
Signed-off-by: Nandor Han <nandor.han@vaisala.com>
spl: fix stack usage check if gd is not initialized
Most platforms do not set up gd->start_addr_sp in SPL. Since this is
required for CONFIG_SPL_SYS_REPORT_SACK_F_USAGE to work correctly, set
up gd->start_addr_sp in SPL to the value passed to
board_init_f_init_reserve if it is not set yet.
Tom Rini [Wed, 8 Jan 2020 23:57:11 +0000 (18:57 -0500)]
Merge tag 'efi-2020-04-rc1' of https://gitlab.denx.de/u-boot/custodians/u-boot-efi
Pull request for UEFI sub-system for efi-2020-04-rc1
This pull request provides:
* support for FIT images for UEFI binaries
* drivers for hardware random number generators
* an implementation of the EFI_RNG_PROTOCOL
* a sub-command for efidebug to display configuration tables
Peng Ma [Wed, 4 Dec 2019 10:36:45 +0000 (10:36 +0000)]
ata: fsl_sata: Continue probing other sata port when failed current port.
In the initialization of sata driver, we want to initialize all port
probes, Therefore, any detection failure between of them should continue
initialization by skipping the current port instead of exit.
Peng Ma [Wed, 4 Dec 2019 10:36:42 +0000 (10:36 +0000)]
ata: sata_sil: Continue probing other sata port when failed current port.
In the initialization of sata driver, we want to initialize all port
probes, Therefore, any detection failure between of them should continue
initialization by skipping the current port instead of exit.
Patrice Chotard [Fri, 6 Dec 2019 14:01:49 +0000 (15:01 +0100)]
treewide: Remove CONFIG_SYS_UBOOT_START from configs board files
As previous CONFIG_SYS_UBOOT_START is now set by default to
CONFIG_SYS_TEXT_BASE when not defined, CONFIG_SYS_UBOOT_START
can be removed from include/configs board files.
Peng Fan [Mon, 6 Jan 2020 08:16:32 +0000 (16:16 +0800)]
imx: imx8mn_evk: add board_mmc_get_env_dev
Add board_mmc_get_env_dev, otherwise,
Loading Environment from MMC...
MMC Device 0 not found
*** Warning - No MMC card found, using default environment
Reviewed-by: Fabio Estevam <festevam@gmail.com> Signed-off-by: Peng Fan <peng.fan@nxp.com>
CPU: Freescale i.MX8MP rev1.0 at 1000 MHz
Reset cause: POR
Model: NXP i.MX8MPlus EVK board
DRAM: 6 GiB
MMC: FSL_SDHC: 1, FSL_SDHC: 2
Loading Environment from MMC... OK
In: serial
Out: serial
Err: serial
Net: No ethernet found.
Hit any key to stop autoboot: 0
u-boot=> mmc list
FSL_SDHC: 1 (SD)
FSL_SDHC: 2
Peng Fan [Mon, 30 Dec 2019 08:52:30 +0000 (16:52 +0800)]
imx: imx8m: only support non-dm code in clock_imx8mm.c
The drivers/clk/imx/*.c are used for CLK dm case, the
clock_imx8mm.c is used for non CLK dm case, let's split
it. Sometimes it is hard to enable CLK dm in SPL stage,
considering code size, malloc size requirement, the splittion
will make it easy to use non CLK dm in SPL stage.
Peng Fan [Mon, 30 Dec 2019 02:03:44 +0000 (10:03 +0800)]
arm: dts: freescale: Add i.MX8MP dtsi support
The i.MX8M Plus Media Applications Processor is part of the growing
mScale family targeting the consumer and industrial market. It brings
an effective Machine Learning and AI accelerator that enables a new
class of applications. It is built in Samsung 14LPP to achieve both
high performance and low power consumption and relies on a powerful
fully coherent core complex based on a quad core ARM Cortex-A53 cluster
and Cortex-M7 low-power coprocessor, audio digital signal processor,
machine learning and graphics accelerators.
Add the basic dtsi support for i.MX8MP.
Patch from Anson Huang for Kernel
https://patchwork.kernel.org/patch/11310915/
Peng Fan [Wed, 11 Dec 2019 06:17:12 +0000 (06:17 +0000)]
imx: imx8mq: handle ESDHC in mxc_get_clock
fsl_esdhc_imx driver will call "mxc_get_clock(MXC_ESDHC_CLK +
dev->seq)", however mxc_get_clock wrongly handle MXC_ESDHC_CLK
as root clk and cause sd card could not be detected in U-Boot proper,
as below:
"Loading Environment from MMC... unable to select a mode"
Handle MXC_ESDHC_CLK in mxc_get_clock to fix the issue.
projects / u-boot.git / log