Wang Huan [Fri, 5 Sep 2014 05:52:44 +0000 (13:52 +0800)]
arm: ls102xa: Add basic support for LS1021AQDS board
LS102xA is an ARMv7 implementation. This patch is to add
basic support for LS1021AQDS board.
One DDR controller
DUART1 is used as the console
For the detail board information, please refer to README.
Signed-off-by: Alison Wang <alison.wang@freescale.com> Signed-off-by: Jason Jin <jason.jin@freescale.com> Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Yuan Yao <yao.yuan@freescale.com> Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
York Sun [Fri, 5 Sep 2014 05:52:43 +0000 (13:52 +0800)]
driver/ddr/fsl: Add support of overriding chip select write leveling
JEDEC spec allows DRAM vendors to use prime DQ for write leveling. This
is not an issue unless some DQ pins are not connected. If a platform uses
regular DIMMs but with reduced DDR ECC pins, the prime DQ may end up on
those floating pins for the second rank. The workaround is to use a known
good chip select for this purpose.
York Sun [Fri, 5 Sep 2014 05:52:41 +0000 (13:52 +0800)]
driver/ddr/freescale: Add support of accumulate ECC
If less than 8 ECC pins are used for DDR data bus width smaller than 64
bits, the 8-bit ECC code will be transmitted/received across several beats,
and it will be used to check 64-bits of data once 8-bits of ECC are
accumulated.
Wang Huan [Fri, 5 Sep 2014 05:52:40 +0000 (13:52 +0800)]
ls102xa: esdhc: Add esdhc support for LS102xA
For LS1, esdhc is big-endian IP. Accessing the registers
should be in big-endian mode. So we use esdhc_read32()
to read Host controller capabilities register for LS1.
For LS1, when using CMD12, cmdtype need to be set to
ABORT, otherwise, next read command will hang.
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Wang Huan [Fri, 5 Sep 2014 05:52:39 +0000 (13:52 +0800)]
esdhc: Add CONFIG_SYS_FSL_ESDHC_LE and CONFIG_SYS_FSL_ESDHC_BE macros
For LS102xA, the processor is in little-endian mode, while esdhc IP is
in big-endian mode. CONFIG_SYS_FSL_ESDHC_LE and CONFIG_SYS_FSL_ESDHC_BE
are added. So accessing ESDHC registers can be determined by ESDHC IP's
endian mode.
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Alison Wang [Fri, 5 Sep 2014 05:52:38 +0000 (13:52 +0800)]
ls102xa: etsec: Add etsec support for LS102xA
This patch is to add etsec support for LS102xA. First, Little-endian
descriptor mode should be enabled. So RxBDs and TxBDs are interpreted
with little-endian byte ordering. Second, TSEC_SIZE and TSEC_MDIO_OFFSET
are different from PowerPC, redefine them for LS1021xA.
Signed-off-by: Alison Wang <alison.wang@freescale.com>
fsl_enet.h defines the mapping of the usual MII management
registers, which are included in the MDIO register block
common to Freescale ethernet controllers. So it shouldn't
depend on the CPU architecture but it should be actually
part of the arch independent fsl_mdio.h.
To remove the arch dependency, merge the content of
asm/fsl_enet.h into fsl_mdio.h.
Some files (like fm_eth.h) were simply including fsl_enet.h
only for phy.h. These were updated to include phy.h instead.
Wang Huan [Fri, 5 Sep 2014 05:52:35 +0000 (13:52 +0800)]
ls102xa: i2c: Add i2c support for LS102xA
The existing i.MX's I2C driver mxc_i2c.c is compatible
with the controller of LS102xA. As I2C's registers
are 8-bit on LS102xA, I2C_QUIRK_REG is enabled to
use 8-bit driver.
This patch is to add I2C 1,2,3 support for LS102xA.
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Wang Huan [Fri, 5 Sep 2014 05:52:34 +0000 (13:52 +0800)]
arm: ls102xa: Add Freescale LS102xA SoC support
The QorIQ LS1 family is built on Layerscape architecture,
the industry's first software-aware, core-agnostic networking
architecture to offer unprecedented efficiency and scale.
Freescale LS102xA is a set of SoCs combines two ARM
Cortex-A7 cores that have been optimized for high
reliability and pack the highest level of integration
available for sub-3 W embedded communications processors
with Layerscape architecture and with a comprehensive
enablement model focused on ease of programmability.
Signed-off-by: Alison Wang <alison.wang@freescale.com> Signed-off-by: Jason Jin <jason.jin@freescale.com> Signed-off-by: Jingchang Lu <jingchang.lu@freescale.com> Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Bo Shen [Wed, 27 Aug 2014 09:28:18 +0000 (17:28 +0800)]
USB: gadget: s3c: get rid of debug compile warning
When enable debug option to compile, it will give the following
warning, this patch is used to get rid of it.
--->8---
warning: 'flags' is used uninitialized in this function [-Wuninitialized]
---8<---
Bo Shen [Wed, 27 Aug 2014 09:28:17 +0000 (17:28 +0800)]
USB: gadget: atmel: get rid of debug compile warning
When enable debug option to compile, it will give the following
warning, this patch is used to get rid of it.
--->8---
warning: 'flags' is used uninitialized in this function [-Wuninitialized]
---8<---
Stephen Warren [Mon, 25 Aug 2014 20:02:15 +0000 (14:02 -0600)]
usb: ci_udc: implement dfu_usb_get_reset
This allows the USB code to determine whether a USB bus reset was issued,
which in turn allows the code to differentiate between a detach (return
to shell prompt) and a board reset/reboot request.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Lukasz Majewski [Mon, 25 Aug 2014 09:07:29 +0000 (11:07 +0200)]
udc: dfu: s3c_udc: Provide function to check if USB reset was asserted
New dfu_usb_get_reset() method is necessary to distinct two different
use cases of dfu-util program.
This method checks if the USB bus reset has been really performed after
DFU DETACH.
Without this function the previous DFU behavior is preserved.
Lukasz Majewski [Mon, 25 Aug 2014 09:07:28 +0000 (11:07 +0200)]
dfu: Provide means to find difference between dfu-util -e and -R
This commit provides distinction between DFU device detach and reset.
The -R behavior is preserved with proper handling of the dfu-util's -e
switch, which detach the DFU device.
By running dfu-util -e; one can force device to finish the execution of
dfu command on target and execute some other scripted commands.
Moreover, some naming has been changed - the dfu_reset() method now is known
as dfu_detach(). New name better reflects the purpose of the code.
It was also necessary to increase the number of usb_gadget_handle_interrupts()
calls since we also must wait for detection of the USB reset event.
Simon Glass [Mon, 11 Aug 2014 15:23:53 +0000 (09:23 -0600)]
dm: gpio: Allow gpio command to adjust GPIOs that are busy
The gpio command mostly relies on gpio_request() and gpio_free() being
nops, in that you can request a GPIO twice. With driver model this is
now implemented correctly, so it fails.
Change the command to deal with a failure to claim the GPIO.
Simon Glass [Mon, 11 Aug 2014 15:23:52 +0000 (09:23 -0600)]
dm: gpio: Enhance gpio command to show only active GPIOs
The GPIO list is very long in many cases and most of them are not used.
By default, show only the GPIOs that are in use, and provide a flag to show
all of them. This makes the 'gpio status' command much more pleasant.
In order to do this, driver model now exposes a method for obtaining the
'function' of a GPIO, which describes whether it is an input or output, for
example. Implementation of this method is optional.
Masahiro Yamada [Sun, 31 Aug 2014 15:47:55 +0000 (00:47 +0900)]
mx6: tqma6: get board support back to Kconfig build system
The QS Systems TQMa6 board support was added by commit cb07d74e
and lost by commit e82abaeb.
Commit e82abaeb merged the IMX branch based on pre-Kconfig
and the mainline based on post-Kconfig, simply deleting
the boards.cfg file. As a result, some boards added just before
the merge were lost.
This commit adds Kconfig, defconfig, MAINTAINERS for TQMa6 board
to work on the Kconfig infrastructure.
arm: Add missing .vectors section to linker scripts
Commit 41623c9 'arm: move exception handling out of start.S files' missed some
linker scripts. Hence, some boards no longer had exception handling linked since
this commit. Restore the original behavior by adding the .vectors section to
these linker scripts.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau.dev@gmail.com> Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Holger Brunck [Fri, 15 Aug 2014 08:51:48 +0000 (10:51 +0200)]
arm/km: disable subpage write for km_kirkwood_pci and kmsuv31 target
Newer FLASH types used on these boards don't allow writing of subpages.
So disable subpage write in the NAND driver. Additionally we need to
tell the UBI layer in the kernel that he also should only write 2048
bytes. This is done with an additional command line parameter for the
kernel commandline.
Tom Rini [Thu, 14 Aug 2014 10:42:36 +0000 (06:42 -0400)]
cmd_bootm.c: Add 'booti' for ARM64 Linux kernel Images
The default format for arm64 Linux kernels is the "Image" format,
described in Documentation/arm64/booting.txt. This, along with an
optional gzip compression on top is all that is generated by default.
The Image format has a magic number within the header for verification,
a text_offset where the Image must be run from, an image_size that
includes the BSS and reserved fields.
This does not support automatic detection of a gzip compressed image.
Marek Vasut [Sun, 3 Aug 2014 23:45:46 +0000 (01:45 +0200)]
ARM: Fix overflow in MMU setup
The patch fixes a corner case where adding size to DRAM start resulted
in a value (1 << 32), which in turn overflew the u32 computation, which
resulted in 0 and it therefore prevented correct setup of the MMU tables.
The addition of DRAM bank start and it's size can end up right at the end
of the address space in the special case of a machine with enough memory.
To prevent this overflow, shift the start and size separately and add them
only after they were shifted.
Hopefully, we only have systems in tree which have DRAM size aligned to
1MiB boundary. If not, this patch would break such systems. On the other
hand, such system would be broken by design anyway.
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Jiandong Zheng [Sat, 2 Aug 2014 03:37:16 +0000 (20:37 -0700)]
arm: bcm281xx: net: Add Ethernet Driver
The Broadcom StarFighter2 Ethernet driver is used in multiple Broadcom
SoC(s) and:
- supports multiple MAC blocks,
- provides support for the Broadcom GMAC.
This driver requires MII and PHYLIB.
Signed-off-by: Jiandong Zheng <jdzheng@broadcom.com> Signed-off-by: Steve Rae <srae@broadcom.com>
Andre Przywara [Fri, 1 Aug 2014 11:35:44 +0000 (13:35 +0200)]
ARM: enable ARMv7 virt support for the Arndale board
To enable hypervisors utilizing the ARMv7 virtualization extension
on the Arndale board, add the simple SMP pen address writer function
and add the required configuration variables to switch all cores to
HYP mode before launching the OS.
This allows booting KVM and Xen directly from u-boot.
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org> Signed-off-by: Andre Przywara <andre.przywara@linaro.org> Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Pavel Machek [Mon, 14 Jul 2014 12:14:17 +0000 (14:14 +0200)]
socfpga: initialize designware ethernet
Enable initialization fo designware ethernet controller. With this
patch, ethernet works in my configuration, provided I set ethernet
address in the environment.
Thomas Chou [Sat, 30 Aug 2014 09:45:23 +0000 (17:45 +0800)]
nios2: rebase nios2-generic board to 3c120 reference design
Though nios2-generic board meant to be a template, it is helpful
to be able to test on a real hardware. As the nios2 linux is
developed and tested on a 3c120 FPGA based Golden Hardware Reference
Design, it makes sense to rebase nios2-generic on this FPGA design.
Thomas Chou [Mon, 25 Aug 2014 09:43:12 +0000 (17:43 +0800)]
serial: move nios2-yanu.h into opencores_yanu driver
The nios2-yanu.h contains hardware registers and bits of
opencores yanu. As there is no other user of this header
, it should be moved into the driver.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw> CC: Renato Andreola <renato.andreola@imagos.it>
Thomas Chou [Mon, 25 Aug 2014 08:50:14 +0000 (16:50 +0800)]
nios2: divide nios2-io.h into each specific drivers and remove it
The nios2-io.h defines hardware registers and bits of several FPGA
IP cores. It could be divided in to the specific drivers, including
altera timer, altera sysid, altera uart and altera jtag uart. The
altera pio and altera spi drivers use their own hardware definitions.
The removal of nios2-io.h will help modularity and maintenance.
socfpga: Fix SOCFPGA build error for Altera dev kit
To fix the build error when build for Altera dev kit, not
virtual target. At same time, set the build for Altera dev
kit as default instead virtual target. With that, U-Boot
is booting well and SPL still lack of few drivers.
Signed-off-by: Chin Liang See <clsee@altera.com> Cc: Pavel Machek <pavel@denx.de> Cc: Marek Vasut <marex@denx.de> Cc: Tom Rini <trini@ti.com> Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Jeroen Hofstee [Sun, 22 Jun 2014 21:10:39 +0000 (23:10 +0200)]
ARM:asm:io.h use static inline
When compiling u-boot with W=1 the extern inline void for
read* is likely causing the most noise. gcc / clang will
warn there is never a actual declaration for these functions.
Instead of declaring these extern make them static inline so
it is actually declared.
cc: Albert ARIBAUD <albert.u.boot@aribaud.net> Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
Stephen Warren [Thu, 7 Aug 2014 23:07:59 +0000 (17:07 -0600)]
usb: hub: don't check CONNECTION in hub_port_reset()
One specific USB 3.0 device behaves strangely when reset by
usb_new_device()'s call to hub_port_reset(). For some reason, the device
appears to briefly drop off the bus when this second bus reset is
executed, yet if we retry this loop, it'll eventually come back after
another two resets.
If USB bus reset is executed over and over within usb_new_device()'s call
to hub_port_reset(), I see the following sequence of results, which
repeats as long as you want:
The device in question is a SanDisk Ultra USB 3.0 16GB memory stick with
USB VID/PID 0x0781/0x5581.
In order to allow this device to work with U-Boot, ignore the
{C_,}CONNECTION bits in the status/change registers, and only use the
ENABLE bit to determine if the reset was successful.
To be honest, extensive investigation has failed to determine why this
problem occurs. I'd love to know! I don't know if it's caused by:
* A HW bug in the device
* A HW bug in the Tegra USB controller
* A SW bug in the U-Boot Tegra USB driver
* A SW bug in the U-Boot USB core
This issue only occurs when the device's USB3 pins are attached to the
host; if only the USB2 pins are connected the issue does not occur. The
USB3 controller on Tegra is in reset, so is not actively communicating
with the device at all - a USB3 analyzer confirms this. Slightly
unplugging the device (so the USB3 pins don't contact) or using a USB2
cable or hub as an intermediary avoids the problem. For some reason,
the Linux kernel (either on the same Tegra board, or on an x86 host)
has no issue with the device, and I observe no disconnections during
reset.
This change won't affect any USB device that already works, since such
devices could not currently be triggering the error return this patch
removes, or they wouldn't be working currently.
However, this patch is quite reliable in practice, hence I hope it's
acceptable to solve the problem.
The only potential fallout I can see from this patch is:
* A broken device that triggers C_CONNECTION/!CONNECTION now causes the
loop in hub_port_reset() to run multiple times. If it never succeeds,
this will cause "usb start" to take roughly 1s extra to execute.
* If the user unplugs a device while hub_port_reset() is executing, and
very quickly swaps in a new device, hub_port_reset() might succeed on
the new device. This would mean that any information cached about the
original device (from the descriptor read in usb_new_device(), which
simply caches the max packet size) might be invalid, which would cause
problems talking to the new device. However, without this change, the
new device wouldn't work anyway, so this is probably not much of a
loss.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Marek Vasut [Fri, 1 Aug 2014 01:09:53 +0000 (03:09 +0200)]
usb: Handle -ENODEV from usb_lowlevel_init()
As we support both Host and Device mode operation, an OTG controller
can return -ENODEV on a port which it found to be in Device mode during
Host mode scan for devices. In case -ENODEV is returned, print that the
port is not available and continue instead of screaming a bloody error
message.
Commit 3ff291f371fa9858426774f3732924bacb61ed1c
(kconfig: convert Kconfig helper script into a shell script)
restored "<board>_config" target for backward compatibility.
It should be documented.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Reviewed-by: Stephen Warren <swarren@nvidia.com>
Stefan Roese [Mon, 25 Aug 2014 09:26:19 +0000 (11:26 +0200)]
net: cpsw: am335x: Drop constant link checking from rx/tx path's
We noticed on the DXR2 platform (AM335x with a SMSC LAN9303 switch connected
to the CPSW MAC) that the network performance in U-Boot is quite poor. Only
when the transfer is started without a cable connected, and the cable is
plugged after the first timeout "T" occured, an increased in performance
can be seen. Debugging has revealed, that the cpsw driver has constant
link checking builtin into the rx and tx functions. This results in the
bad performance and seems to be unnecessary. The link has already been
checked in the init function, before the transfer is started. This usually
is sufficient.
BTW: I have seen no other network driver in U-Boot so far, that constantly
checks for link in the rx / tx functions.
The performance numbers on the DXR2 board are:
0.56 MiB/s cpsw_check_link() in rx and tx path
0.87 MiB/s cpsw_check_link() only in tx path
1.0 MiB/s cpsw_check_link() only in rx path
2.7 MiB/s no cpsw_check_link() in rx and tx path
So with this patch the network performance on DXR2 increases from 0.56
to 2.7 MiB/s (nearly 5 times as fast).
Signed-off-by: Stefan Roese <sr@denx.de> Tested-by: Samuel Egli <samuel.egli@siemens.com> Tested-by: Heiko Schocher <hs@denx.de> Cc: Vladimir Koutny <vladimir.koutny@streamunlimited.com> Cc: Mugunthan V N <mugunthanvnm@ti.com> Cc: Joe Hershberger <joe.hershberger@gmail.com> Cc: Tom Rini <trini@ti.com>
Masahiro Yamada [Mon, 25 Aug 2014 03:39:48 +0000 (12:39 +0900)]
tools/genboardscfg.py: improve performance
I guess some developers are already getting sick of this tool
because it generally takes a few minites to generate the boards.cfg
on a reasonable computer.
The idea popped up on my mind was to skip Makefiles and
to run script/kconfig/conf directly.
This tool should become about 4 times faster.
You might still not be satisfied, but better than doing nothing.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Acked-by: Simon Glass <sjg@chromium.org>
Masahiro Yamada [Mon, 25 Aug 2014 03:39:46 +0000 (12:39 +0900)]
tools/genboardscfg.py: fix minor problems on termination
This tool deletes the incomplete boards.cfg
if it encounters an error or is is terminated by the user.
I notice some problems even though they rarely happen.
[1] The boards.cfg is removed if the program is terminated
during __gen_boards_cfg() function but before boards.cfg
is actually touched. In this case, the previous boards.cfg
should be kept as it is.
[2] If an error occurs while deleting the incomplete boards.cfg,
the program throws another exception. This hides the privious
exception and we will not be able to know the real cause.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Acked-by: Simon Glass <sjg@chromium.org>
Masahiro Yamada [Mon, 25 Aug 2014 03:39:45 +0000 (12:39 +0900)]
tools/genboardscfg.py: wait for unfinished subprocesses before error-out
When an error occurs or the program is terminated by the user
on the way, the destructer __del__ of class Slot is invoked and
the work directories are removed.
We have to make sure there are no subprocesses (in this case,
"make O=<work_dir> ...") using the work directories before
removing them. Otherwise the subprocess spits a bunch of error
messages possibly causing more problems. Perhaps some users
may get upset to see too many error messages.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Acked-by: Simon Glass <sjg@chromium.org>
Masahiro Yamada [Mon, 25 Aug 2014 03:39:44 +0000 (12:39 +0900)]
tools/genboardscfg.py: be tolerant of insane Kconfig
The tools/genboardscfg.py expects all the Kconfig and defconfig are
written correctly. Imagine someone accidentally has broken a board.
Error-out just for one broken board is annoying for the other
developers. Let the tool skip insane boards and continue processing.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Acked-by: Simon Glass <sjg@chromium.org>
Masahiro Yamada [Mon, 25 Aug 2014 03:39:43 +0000 (12:39 +0900)]
tools/genboardscfg.py: be tolerant of missing MAINTAINERS
tools/genboardscfg.py expects all the boards have MAINTAINERS.
If someone adds a new board but misses to add its MAINTAINERS file,
tools/genboardscfg.py fails to generate the boards.cfg file.
It is annoying for the other developers.
This commit allows tools/genboardscfg.py to display warning messages
and continue processing even if some MAINTAINERS files are missing
or have broken formats.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Acked-by: Simon Glass <sjg@chromium.org>
Masahiro Yamada [Mon, 25 Aug 2014 03:39:42 +0000 (12:39 +0900)]
tools/genboardscfg.py: ignore defconfigs starting with a dot
Kconfig in U-Boot creates a temporary file configs/.tmp_defconfig
during processing "make <board>_defconfig". The temporary file
might be left over for some reasons.
Just in case, tools/genboardscfg.py should make sure to
not read such garbage files.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Acked-by: Simon Glass <sjg@chromium.org>
Simon Glass [Fri, 22 Aug 2014 20:26:43 +0000 (14:26 -0600)]
Fix test failure caused by bad handling of ramdisk
Commit e3a5bbce broke the FIT image tests by not loading a ramdisk even if
a load address is provided in the FIT. The rationale was that a load address
of 0 should be considered to mean 'do not load'.
Add a new load operation which supports this feature, so that the ramdisk
will be loaded if a non-zero load address is provided.
Masahiro Yamada [Fri, 22 Aug 2014 10:42:28 +0000 (19:42 +0900)]
scripts: refetch scripts/setlocalversion from Linux 3.16
Now we have CONFIG_LOCALVERSION and CONFIG_LOCALVERSION_AUTO
in Kconfig so we can use scripts/setlocalversion without
any adjustment. Copy it from Linux 3.16 as is.
Masahiro Yamada [Fri, 22 Aug 2014 05:33:41 +0000 (14:33 +0900)]
buildman: run genboardscfg.py all the time
This commit makes sure boards.cfg is up to date before starting
the build tests. tools/genboardscfg.py exits immediately printing
"boards.cfg is up to date. Nothing to do." when boards.cfg is
already new.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Acked-by: Simon Glass <sjg@chromium.org>
Masahiro Yamada [Fri, 22 Aug 2014 05:33:40 +0000 (14:33 +0900)]
MAKEALL: run genboardscfg.py all the time
This commit makes sure boards.cfg is up to date before starting
the build tests. tools/genboardscfg.py exits immediately printing
"boards.cfg is up to date. Nothing to do." when boards.cfg is
already new.
Masahiro Yamada [Fri, 22 Aug 2014 05:10:43 +0000 (14:10 +0900)]
tools/genboardscfg.py: fix a bug of MAINTAINERS handling
This patch fixes a minor problem:
If a block without "F: configs/*_defconfig" is followed by another
block with "F: configs/*_defconfig", the maintainers from the
former block are squashed into the latter.
Łukasz Majewski [Fri, 22 Aug 2014 07:12:58 +0000 (09:12 +0200)]
samsung: s5p_goni: fix: Add missing definitions for G_DNL_UMS gadget
The commit (SHA1: 8fc171318e352) reintroduced correct values for vendor and
product IDs required for UMS gadget to work properly either at Windows or
Linux.
This data was missing for GONI target, so this commit corrects this mistake.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com> Acked-by: Robert Baldyga <r.baldyga@samsung.com> Acked-by: Minkyu Kang <mk7.kang@samsung.com>
projects / u-boot.git / log