Since the mxs_nand_spl has implemented adjust read offset in
nand_spl_load_image, so we don't need to check the bad block in
nand_spl_adjust_offset. Directly return the offset to continue
read by nand_spl_load_image.
Ye Li [Tue, 17 Aug 2021 09:10:35 +0000 (17:10 +0800)]
arm: imx8m: Fix pad DSE issue for i.MX8MM/MN/MP
According to 8MM/MN/MP reference manual, their pad registers only have
4 valid DSE values. And DSE2 and DSE4 are different with current
definitions in iomux-v3.h. Fix the issue to align with manual.
Signed-off-by: Ye Li <ye.li@nxp.com> Acked-by: Peng Fan <peng.fan@nxp.com>
Ye Li [Tue, 17 Aug 2021 09:09:20 +0000 (17:09 +0800)]
mmc: fsl_esdhc_imx: Fix clock disable issue
The SD clock disable is wrapped by MMC_SUPPORTS_TUNING. So it
only works when UHS is enabled. However, in SD initialization the
power cycle does not depends on UHS. But the power cycle needs
disable the SD clock before power down.
So this causes a problem when UHS is not enabled. Some cards can't
become ready (ACMD14 timeout) due to the clock is enabled during
power cycle.
Signed-off-by: Ye Li <ye.li@nxp.com> Reviewed-by: Haibo Chen <haibo.chen@nxp.com> Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Heiko Schocher [Tue, 17 Aug 2021 06:17:18 +0000 (08:17 +0200)]
imx: spl: fix imx8m secure boot
cherry-picked from NXP code: 719d665a87c6: ("MLK-20467 imx8m: Fix issue for booting signed image through uuu")
which fixes secure boot on imx8m based boards. Problem was
that FIT header and so IVT header too, was loaded to
memallocated address. So the ivt header address coded
in IVT itself does not fit with the real position.
Signed-off-by: Heiko Schocher <hs@denx.de> Tested-by: Tim Harvey <tharvey@gateworks.com>
Tom Rini [Wed, 22 Sep 2021 18:50:39 +0000 (14:50 -0400)]
Convert CONFIG_NAND_OMAP_ECCSCHEME to Kconfig
The values of CONFIG_NAND_OMAP_ECCSCHEME map to the enum in
include/linux/mtd/omap_gpmc.h for valid ECC schemes. Make which one we
will use be a choice statement, enumerating the ones which we have
implemented.
Tom Rini [Wed, 22 Sep 2021 18:50:37 +0000 (14:50 -0400)]
Convert CONFIG_NAND_FSL_ELBC et al to Kconfig
This converts the following to Kconfig:
CONFIG_NAND_FSL_ELBC
CONFIG_NAND_FSL_IFC
Note that a number of PowerPC platforms had previously enabled
CONFIG_NAND_FSL_ELBC without CONFIG_MTD_RAW_NAND, and now they no longer
enable the option, reducing the size of a few functions.
Tom Rini [Wed, 22 Sep 2021 18:50:35 +0000 (14:50 -0400)]
nand.h: Cleanup linux/mtd/rawnand.h usage
We only include <linux/mtd/rawnand.h> in <nand.h> for the forward
declaration of struct nand_chip, so do that directly. Then, include
<linux/mtd/rawnand.h> where required directly.
Tom Rini [Wed, 22 Sep 2021 18:50:32 +0000 (14:50 -0400)]
Convert CONFIG_SYS_NAND_BAD_BLOCK_POS to Kconfig
This converts the following to Kconfig:
CONFIG_SYS_NAND_BAD_BLOCK_POS
In order to do this, introduce a choice for HAS_LARGE/SMALL_BADBLOCK_POS
as those are the only valid values. Use LARGE as the default as no
in-tree boards use SMALL, but it is possible.
Tom Rini [Wed, 22 Sep 2021 18:50:27 +0000 (14:50 -0400)]
m53menlo: Switch to deriving CONFIG_SYS_NAND_PAGE_COUNT
Typically platforms will define CONFIG_SYS_NAND_PAGE_COUNT based on
CONFIG_SYS_NAND_BLOCK_SIZE / CONFIG_SYS_NAND_PAGE_SIZE. Switch to this
in preparation for migrating CONFIG_SYS_NAND namespace to Kconfig.
Cc: Marek Vasut <marex@denx.de> Cc: Olaf Mandel <o.mandel@menlosystems.com> Signed-off-by: Tom Rini <trini@konsulko.com>
Simon Glass [Sun, 19 Sep 2021 21:14:49 +0000 (15:14 -0600)]
test: Allow hush tests to run in parallel
The -z tests don't really need to be part of the main set. Separate them
out so we can drop the test setup/cleans functions and thus run all tests
in parallel.
Simon Glass [Sun, 19 Sep 2021 21:14:48 +0000 (15:14 -0600)]
test: Allow vboot tests to run in parallel
Update the tests to use separate working directories, so we can run them
in parallel. It also makes it possible to see the individual output files
after the tests have completed.
test/py: Check hashes produced by mkimage against known values
Target code and mkimage share the same hashing infrastructure. If one
is wrong, it's very likely that both are wrong in the same way. Thus
testing won't catch hash regressions. This already happened in
commit 92055e138f28 ("image: Drop if/elseif hash selection in
calculate_hash()"). None of the tests caught that CRC32 was broken.
Instead of testing hash_calculate() against itself, create a FIT with
containing a kernel with pre-calculated hashes. Then check the hashes
produced against the known good hashes.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Samuel Holland [Sat, 11 Sep 2021 22:05:53 +0000 (17:05 -0500)]
gpio: Factor out DT flag translation
The generic GPIO flags binding is shared across many drivers, some of
which need their own xlate function. Factor out the flag translation
code from gpio_xlate_offs_flags so it does not need to be duplicated.
Signed-off-by: Samuel Holland <samuel@sholland.org> Reviewed-by: Simon Glass <sjg@chromium.org>
arm: imx: mx7: Move CONFIG_OPTEE_TZDRAM_SIZE from lib/optee
This config is only used by three boards with this SOC. Most other
platforms derive this information from devicetree, and are unlikely
to ever need this config.
Moreover, it is confusing when Kconfig asks for this value under
"Support OPTEE images", but does not do anything with the value.
Move it to imx7 for those boards who still make use of it.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
This value is not used by u-boot, and it should not. The load address
of an OPTEE image is defined by said image. Either a uImage or a FIT
will have a defined load address and entry point. Those values are the
correct ones, not CONFIG_OPTEE_LOAD_ADDR.
Commit f25006b96e9f ("optee: Add CONFIG_OPTEE_LOAD_ADDR") justifies
this config by requiring its presence in u-boot's .config for other
images as part of a larger build, claiming it is "the best way".
This argument is not persuasive. U-boot's configuration is driven by
platform requirements, not the other way around. It seems more likely
that the argument is conflating tooling issues with Kconfig. Yocto and
buildroot have excellent mechanisms for defining values across the
board (pun intended). u-boot's Kconfig is the wrong place to do it.
Furthermore, it is not "best" for u-boot because it hardcodes a value
which is then not used. In fact the load address that u-boot uses is
the one derived from the OPTEE image.
Confused yet? I sure was. To prevent future confusion, remove
CONFIG_OPTEE_LOAD_ADDR.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
It is no longer used in u-boot. Information about the TZDRAM location
is usually available in the devicetree as "/reserved-memory/" nodes.
Because this isn't used, remove it.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
lib: optee: Avoid CONFIG_TZDRAM_* in optee_verify_bootm_image()
The configs TZDRAM_BASE and TZDRAM_SIZE are expected to describe the
memory allocated to the OPTEE region. according to according to commit c5a6e8bd00cc ("optee: Add optee_verify_bootm_image()"). The TZDRAM is
with some limitations, described by "/reserved-memory" nodes in the
devicetree.
Consequently TZDRAM_BASE and TZDRAM_SIZE can point to imaginary
regions which have nothing to do with actual DRAM. They are not used
to configure the hardware or set up the Trust Zone Controller (TZC)
for OP-TEE -- the devicetree values are used instead.
When a valid OP-TEE image does not fall within the region described by
these configs, u-boot will refuse to load it. In fact, it mostly
serves to cause "bootm" to reject perfectly good OP-TEE images.
Ironically, someone has to correctly configure the devicetree for
TZDRAM, then go back and enter the same information in Kconfig for
"bootm". To remedy this, do not use TZDRAM_BASE and TZDRAM_SIZE in the
verification of OPTEE images.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
The configuration CONFIG_OPTEE is defined 2 times:
1- in lib/optee/Kconfig for support of OPTEE images loaded by bootm command
2- in drivers/tee/optee/Kconfig for support of OP-TEE driver.
It is abnormal to have the same CONFIG define for 2 purpose;
and it is difficult to managed correctly their dependencies.
Moreover CONFIG_SPL_OPTEE is defined in common/spl/Kconfig
to manage OPTEE image load in SPL.
This definition causes an issue with the macro CONFIG_IS_ENABLED(OPTEE)
to test the availability of the OP-TEE driver.
This patch cleans the configuration dependency with:
- CONFIG_OPTEE_IMAGE (renamed) => support of OP-TEE image in U-Boot
- CONFIG_SPL_OPTEE_IMAGE (renamed) => support of OP-TEE image in SPL
- CONFIG_OPTEE (same) => support of OP-TEE driver in U-Boot
- CONFIG_OPTEE_LIB (new) => support of OP-TEE library
After this patch, the macro have the correct behavior:
- CONFIG_IS_ENABLED(OPTEE_IMAGE) => Load of OP-TEE image is supported
- CONFIG_IS_ENABLED(OPTEE) => OP-TEE driver is supported
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Marek Vasut [Tue, 14 Sep 2021 03:21:48 +0000 (05:21 +0200)]
mtd: cqspi: Fix division by zero
Both dummy.nbytes and dummy.buswidth may be zero. By not checking
the later, it is possible to trigger division by zero and a crash.
This does happen with tiny SPI NOR framework in SPL. Fix this by
adding the check and returning zero dummy bytes in such a case.
Fixes: 38b0852b0ea ("spi: cadence-qspi: Add support for octal DTR flashes") Signed-off-by: Marek Vasut <marex@denx.de> Cc: Jagan Teki <jagan@amarulasolutions.com> Cc: Vignesh R <vigneshr@ti.com> Cc: Pratyush Yadav <p.yadav@ti.com>
[trini: Drop Pratyush's RB as his requested changes weren't made as
Marek disagreed]
Jan Kiszka [Sat, 18 Sep 2021 06:17:55 +0000 (08:17 +0200)]
watchdog: rti_wdt: Add support for loading firmware
To avoid the need of extra boot scripting on AM65x for loading a
watchdog firmware, add the required rproc init and loading logic for the
first R5F core to the watchdog start handler. In case the R5F cluster is
in lock-step mode, also initialize the second core. The firmware itself
is embedded into U-Boot binary to ease access to it and ensure it is
properly hashed in case of secure boot.
One possible firmware source is https://github.com/siemens/k3-rti-wdt.
The board is responsible for providing the firmware as additional
loadable via the U-Boot fit image. The driver will pick up its location
from /fit-images/k3-rti-wdt-firmware then.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Jan Kiszka [Sat, 18 Sep 2021 06:17:53 +0000 (08:17 +0200)]
board: siemens: Add support for SIMATIC IOT2050 devices
This adds support for the IOT2050 Basic and Advanced devices. The Basic
used the dual-core AM6528 GP processor, the Advanced one the AM6548 HS
quad-core version.
Both variants are booted via a Siemens-provided FSBL that runs on the R5
cores. Consequently, U-Boot support is targeting the A53 cores. U-Boot
SPL, ATF and TEE have to reside in SPI flash.
Full integration into a bootable image can be found on
https://github.com/siemens/meta-iot2050
Based on original board support by Le Jin, Gao Nian and Chao Zeng.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Jan Kiszka [Sat, 18 Sep 2021 06:17:52 +0000 (08:17 +0200)]
arm: dts: Add IOT2050 device tree files
Prepares for the addition of the IOT2050 board which is based on the TI
AM65x. The board comes in four variants, Basic and Advanced, each as
product generation 1 (SR1.0) and 2 (SR2.x), so there are separate dts
files needed. Furthermore, the SPL has its own device tree.
Based on original board support by Le Jin, Gao Nian and Chao Zeng.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Vladimir Oltean [Fri, 17 Sep 2021 12:11:21 +0000 (15:11 +0300)]
pci: include pci_internal.h inside pci_auto.c
To avoid a build warning with W=1, provide a function prototype for
dm_pciauto_prescan_setup_bridge, which is a non-static function whose
definition is inside pci_auto.c.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Vladimir Oltean [Fri, 17 Sep 2021 12:11:20 +0000 (15:11 +0300)]
pci: provide prototype for pci_skip_dev outside of #if defined(CONFIG_DM_PCI_COMPAT)
The weak definition of pci_skip_dev from drivers/pci/pci_common.c is not
under CONFIG_DM_PCI_COMPAT, and that definition needs a previous
function prototype declaration to avoid W=1 build warnings.
That prototype is not available due to it being under CONFIG_DM_PCI_COMPAT,
so move it outside of that preprocessor block.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
rtc: rx8025: revise single register write to use offset
Writing of individual registers was not functioning
correctly as a 0 'offset' byte under DM-managed
I2C was being appended in front of register we
wanted to access.
The RX8025/RX8035 does not like having it's time registers
set byte-by-byte in separate I2C transactions.
From the note at the top of the file, it appears
target-dependent workarounds have been used in the
past for this.
Resolve this by setting the time registers in a single
I2C transaction.
As part of this, also ensure the '24/12' flag in the RTC
is reset before writing the date (instead of after), otherwise
the RX8035 will clear the seconds and minutes registers.
Tested on Traverse Ten64 (NXP LS1088A) with RX8035.
Tom Rini [Fri, 10 Sep 2021 21:37:43 +0000 (17:37 -0400)]
arm: ti: k3: Resync dts files and bindings with Linux Kernel v5.14
This resyncs the dts files for all of the currently in-tree K3
platforms, along with relevant bindings, with the v5.14 Linux Kernel
release. Of note are that the main-navss/mcu-navss nodes were renamed
to main_navss / mcu_navss and so the u-boot.dtsi files needed to be
updated to match.
Tom Rini [Sat, 2 Oct 2021 19:47:28 +0000 (15:47 -0400)]
Merge branch '2021-10-01-assorted-removal-and-migration' into next
- Remove the last non-CONFIG_DM boards, and their related unused code.
- Finish a few partial migrations to Kconfig, and remove some redundant
serial related code.
Tom Rini [Mon, 13 Sep 2021 21:24:53 +0000 (17:24 -0400)]
serial: Use the default CONFIG_SYS_BAUDRATE_TABLE in more platforms
A number of platforms are still defining CONFIG_SYS_BAUDRATE_TABLE to
the fallback default of "{ 9600, 19200, 38400, 57600, 115200 }", but
with varying whitespace, or were introduced after the default fallback
was added. Use the default table here.
Retrieve current terminal settings via tcgetattr(), set to raw mode with
cfmakeraw(), enable receiver via CREAD and ignore modem control lines
via CLOCAL.
Signed-off-by: Pali Rohár <pali@kernel.org> Signed-off-by: Marek Behún <marek.behun@nic.cz> Reviewed-by: Stefan Roese <sr@denx.de>
Marek Behún [Fri, 24 Sep 2021 21:07:07 +0000 (23:07 +0200)]
tools: kwboot: Check whether baudrate was set to requested value
The tcsetattr() function can return 0 even if baudrate was not changed.
Check whether baudrate was changed to requested value, and in case of
arbitrary baudrate, check whether the set value is within 3% tolerance.
Signed-off-by: Marek Behún <marek.behun@nic.cz> Reviewed-by: Stefan Roese <sr@denx.de>
projects / u-boot.git / log